Samsung AM18B1C09 User's Manual
Contents
1. Airing Your Room On Timer Off Timer i Turbo E Sal vy On Timer If the atmosphere in your room is stale you can air the room using the Fan feature If necessary press the On Off button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps If the ef is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in FAN mode The temperature is set automatically Note You change modes at any time Select the fan speed by pressing the FAN button one or more times until the required setting is displayed da Low Sal Medium Sal High Result Each time you press the FAN button the indoor unit beeps To control the direction of the air flow refer to page 15 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner 1 Press the SWING button one or more times as required Result The outer blade is adjusted vertically RECOMMENDATION When Adjust the blade to face Cooling Upwards 2 If you want t2. F to 90 F approx 18 to 43 C approx 18 to 32 approx If the cooling operation is used at over 92 F 33 C indoor temperature then it does not cool as its full capacity Cleaning Your Air Conditioner ENGLISH To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTA NT Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Open the front grille by lifting the tabs on the lower right and left sides of the indoor unit 2 Disassemble the front grille by pulling it forwards 3 Hold the edge of the air filter under the front grille and pull to release them 4 Remove all dust on the air filters with a vacuum cleaner or brush 5 Clean the front panel with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals 6 Reassemble the air filters and the front grille Note If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call
3. Problem Explanation Solution The air conditioner does not operate at all Check that the breaker used for the air conditioner is switched on Check that the 5 Way indicator on the indoor unit is on if necessary press the On Off button on the remote control Check whether the TIMER indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 16 and 17 for further details The air conditioner does not operate with the remote control 99 Check that there are no obstacles between you and the indoor unit Check the remote control batteries Check that you are close enough to the indoor unit seven metres yards 23ft or less No beep is heard when you press the 7 On Off on the remote control Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected AUTO COOL The room temperature may be too low or too high Dust may be blocking the air filter guard refer to page 21 for cleaning instructions Check that there is no obstacle in front of the outdoor unit The fan speed does not change when you press the FAN button Check that the operating mode is set to CO
4. not the fan speed 1 If necessary press the On Off button Result o The 5 Way indicator on the indoor unit lights up On Timer The air conditioner starts up in the mode selected when the unit was last used Off Timer The indoor unit beeps OS a PORTANT The air conditioner is fitted with a protection mechanism to D 0 prevent the unit from being damaged when it is started Gway immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe is not displayed at the top of the remote control auo press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in AUTO mode Turbo E Note You change modes at any time 3 To adjust the standard temperature The air conditioner automatically set the standard temperature by the current room temperature press the TEMPERATURE buttons one or more times SET TEMP SET TEMP SET TEMP SET TEMP C 4 F 2 C 2 F 4 C Standard temperature 2 1 4 2 TA lt When you feel hot gt lt When you feel chilly gt Turbo O g Cooling Your Room ENGLISH You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press the On Off button Result The 5 Way indicator on the indoor unit lights up On Time
5. of the installation book you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Installing the Remote Controller Holder 1 Place the remote controller holder on the wall lt 3 2 Fix the remote controller holder by tightening the screws 3 Put the remote controller into the holder as shown in the figure O If you want to install the holder easily you had better install the holder on the wooden frame 5 Way Function You can select the 5 Way function with operating mode of the air conditioner for more comfortable circumstance
6. to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the ON TIMER button until 2 0 Hr is displayed 2 Press the Set Cancel button 3 Press the OFF TIMER button until 4 0 Hr is displayed 4 Press the Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the MODE button or the TEMPERATURE buttons after setting the Off timer To Cancel the Off Timer 1 To cancel the Off Timer press the OFF TIMER button one or more times until the timer setting disappears LI LUE tI 2 Press the Set Cancel button Note If you want to turn off the air conditioner before the timer reaches the setting time press the ON OFF button E ENGLISH 8 Sel c 9 Setting the Sleep Timer a 4 The Sleep Timer can be used when you are cooling your room to switch the air conditioner off automatically after a period of six hours Note If you wish to switch the unit off at a specific time refer to page 17 1 Make sure that you have selected either COOL mode 2 Press the button one or more times until appears on the remote control Result The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below Cooling The desired temperature is increased by 2 F 1 C every FOC hour Fn l When it has been in
7. 9 Air Outlet Air Outlet Air Outlet Air Inlet Rear Air Inlet Rear Tu c Air Inlet Rear ARA Connection Valve Connection Valve lt o 0 Connection Valve ENGLISH Remote Control Buttons and Display Remote control transmission indicator Operating mode AUTO 3 COOL DRY FAN Temperature setting Turbo mode Sleep mode Fan speed Air flow direction On Timer setting Off Timer setting Battery discharge indicator 5 Way selection button SET TEMP um mp LC EU F OFF TIMER Ett ao Mode selection button AUTO COOL DRY FAN Temperature adjustment buttons Turbo Sleep mode selection button Fan speed adjustment button Swing button On Timer button Off Timer button On Off amp Timer Set Cancel button ENGLISH Getting Started You have just purchased a split type air conditioner and it has been installed by your installation specialist Your Owner s Instructions contains valuable information on using your air conditioner Please take the time to read it as it will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages from 4 to 6 Indoor and outdoor units Remote control buttons and display They will help you find the buttons and understand the symbols displayed Inthe main part
8. OL or FAN in the AUTO mode the fan speed changes automatically and in the DRY mode it is set to AUTO The air flow direction does not change when you press the SWING button Check that the air conditioner has been switched on if necessary press the button on the remote control The timer is not correctly triggered Check that the timer has been programmed correctly see pages 16 and 17 Odours are permeated in the room during air conditioning Air the room Installing a Filter Option ENGLISH The air conditioner can be fitted with a deodorizing and Bio Pure filter to remove minute dust particles or odours The service life of the filter is approximately three months depending on the time during which the air conditioner is used 1 Remove the vinyl packing from the filter Note not remove the packing from a deodorizing filter until you wish to use the filter as it will lose its properties a filter 2 nsert the filter in the filter holder and press the three insert tabs until you hear a click Bio Pure Filter 3 Open the front grille by pulling on the tabs on the lower right and left sides of the indoor unit 4 Take out the existing filter and replace it with the new one Technical Specifications Indoor unit Outdoor unit Indoor unit Outdoor unit AM18B1C09 UM18B1C2 AM26B1C13 UM26B1C2 MODEL Type 2 Comp 2 Room 2 Comp 2 Room Pe
9. OWNERS INSTRUCTIONS amp INSTALLATION MANUAL z MANUAL DE INSTRUCCIONES amp g MANUAL DE INSTALACION MANUEL D UTILISATION amp 8 MANUEL D INSTALLATION Indoor Unit Outdoor Unit AM18B1C09 UM18B1C2 AM26B1C13 UM26B1C2 4 0 278188 i MULTI SPLIT TYPE ROOM AIR CONDITIONER ACONDICIONADOR DE AIRE DOMESTICO SISTEMA MULTI SPLIT Refrigeraci n CLIMATISEUR DE TYPE MULTIPLE Refroidissement DOP DB98 05640A 3 Safety Precautions The following safety precautions must be taken when using your air conditioner 1 Make sure that the indoor unit is correctly ventilated at all times do NOT place clothing or other materials over it 2 NEVER spill liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist 3 Do NOT insert anything between the air flow blades as the inner fan may become damaged and you may be hurt Keep children away from the indoor unit 4 Do NOT place any obstacles in front of the outdoor unit 5 If the remote control will not be used for a long time remove the batteries 6 Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased 7 If the supply cord is damaged it must be replaced by a s
10. cator stops The selected mode and the temperature on the display disappear after 10 seconds The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting 3 To select an operating mode in advance press the button until the desired mode is displayed at the top of the remote control Result The air conditioner will run in the selected mode when it is turned on To Cancel the On Timer 1 To cancel the On Timer press the ON TIMER button one or more times until the timer setting disappears 2 Pressthe Set Cancel button Note If you want to turn on the air conditioner before the timer reaches the setting time press the ON OFF button Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the OFF TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive 2 Press the Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off timer setting Example If you would like
11. creased Set by 4 2 after two hours TEMP the temperature is maintained Stari Stop for four hours To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the w9 button Result The indoor unit beeps The is no longer displayed The air conditioner operates normally Operating Recommendations ENGLISH Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns you must press the ON OFF button to restart it Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automatic protection feature may be triggered and the air conditioner stopped Low temperatures A water leak or some other malfunction may occur if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Cooling 70 to 109 F approx 65 F to 90 F approx 21 to 43 C approx 18 C to 32 C approx 80 or less Drying 65 F to 109 approx 65
12. de Cooling Your Room Changing the Room Temperature Quickly m Removing Excess Humidity m Airing Your Room m Adjusting the Air Flow Direction Vertically m Adjusting the Air Flow Direction Horizontally PROGRAMMING YOUR AIR CONDITIONER Setting the On m Setting the Off mSetingiheSleeplimer RECOMMENDATIONS FOR USE m Operating Recommendations m Temperature and Humidity Ranges m Cleaning Your Air Conditioner m Solving Common Problems m Installing a Filter Option TECHNICAL SPECIFICATIONS ENGLISH View of the Unit The design and shape are subject to change according to the model Indoor Unit Air filter Air flow blades outlet Air Inlet under the grille Timer indicator Remote Control Sensor Timer e STANDARD indicator SAVING Indicator 5Way E gt SILENCE indicator NATURE indicator POWER indicator OY a amp 5 Way Selection button Note For details on the 5 Way refer to page
13. he blade to move up and down automatically when the air conditioner is operating press the SWING button Result The blade move up and down around the base position set 3 To stop the blade moving and down press the SWING button again Note Ifyou switch the air conditioner Then the blade is Off Closed completely On again Set to the initial position powered E On Timer Off Timer Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades Just as the outer air flow blade can be adjusted vertically the inner blades can be adjusted horizontally 1 Adjust each set of inner blades to the required position by pushing or pulling them sideways ENGLISH Setting the On Timer LUG LUE SET TEMP On Ti Grim Off Timer cel F SO g ZO Off Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the ON TIMER button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hour inclusive 2 Press the Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indi
14. pecial cord or assembly available from the manufacturer or its service centre 8 This device must be installed according to the national electrical rules 9 Before disposing of the remote control it is necessary to remove batteries 10 The appliance is not intended for use by young children or infirm person without supervision young children should be supervised to ensure that they do not play with the appliance 11 Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency CAUTION The manufacturer does not take any responsibility for any accidents that occur because the air conditioner is not fixed firmly or installed securely during installing or using the product In case you experience difficulty in installation you must use an installation specialist An accident will occur if the installation is not done as recommends in the installation guide Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions m View of the m Remote Control Buttons and Display m Getting Started m Inserting the Remote Control Batteries m Installing the Remote Controller Holder OPERATING YOUR AIR CONDITIONER moWayfFuncton m Selecting the Automatic Operating Mo
15. r The air conditioner starts up in the mode selected when the unit was last used Timer The indoor unit beeps oy PORTANT The air conditioner is fitted with a protection mechanism to SA prevent the unit from being damaged when it is started way immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe X is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in COOL mode Note You change modes at any time Turbo 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 65 F 18 C and 86 F 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 F 1 C The indoor unit beeps The air conditioner starts cooling provided that the room LAY temperature is higher than the selected temperature f 1 b the fan will however operate Ct We Turbo CS 4 Select the fan speed by pressing the FAN button one or more times until the required setting is displayed Automatic rotated Low a Medium ul High Turbo E Result Each time you press the FAN but
16. rformance Capacity Cooling A B Unit 9000 A B Unit 12500 Ratings SEER 10 0 10 0 Moisture Removal 3 4 Air FLOW Cooling HIGH 255 300 Sound Rating Outdoor 57 Electrical The number of operation 1 Unit operation 2 Unit operation 1 Unit operation 2 Unit operation Data Power source 208 230V 60Hz 208 230V 60Hz Min Ampacity 43 8 4 6 1 11 4 Cooling Watts W 990 1920 1360 2550 Refrigeration Indoor unit A Unit B Unit A Unit B Unit Lines Connections Flare Flare Liquid Line O D i 6 35 1 4 6 35 1 4 Suction Line O D 9 52 3 8 12 70 1 2 Factory Pre charge 50 16 5 0 163 Max Line length 15 0 491 15 0 49 Max Height Difference 7 0 23 7 0 23 Dimensions wy Hx p 790 x 245 x 165 880 x 638 x 310 790 x 245 x 165 1000 x 790 x 310 amp Weight 316 92 X 62 342 25 12 1 315 92x 62 302X31 X 124 Net Weight 17 132 3 17 152 1 Standard rating conditions Cooling indoor WB DB WB 80 67 95 75 MODEL Indoor unit Indoor unit ENGLISH Outdoor unit AM27B1C07 AM27B1C13 UM27B1C3 2 Comp 3 Room Performance Ratings Capacity Cooling A Unit 13000 B C Unit 7000 SEER 10 0 Moisture Removal 4 Air FLOW Cooling HIGH 300 Sound Rating Outdoor Electrical Data The number of opera
17. s You can use the 5 Way function with the indoor unit as well as the remote control Thus you can use this function even though you have lost your remote control Using with the indoor unit 1 Press the b ON OFF button one time and then select the desired a Timer To obtain a n Then select POW e v Normal operating STANDARD mode 5 Way Reducing the uncomfortable temperature gradually ele High fan speed POWER mode SET sus Compressor run time reduced SAVING mode Fan speed reduces as the temperature SILENCE mode decreases 2 Tostop the operating press the 5 ON OFF button until all indicators turn off ote Even if the air conditioner has been turned on via the ON OFF button on the unit operations can still be controlled using the remote control as usual Selecting with the Remote Control To select the 5 Way function with the remote control press the 5 Way button one or more times until the desired mode is selected On Timer Each time you press the 5 Way button amp 9 Each 5 Way indicator on the indoor unit lights up in order Off Timer cel A og ENGLISH Selecting the Automatic Operating Mode You can start the air conditioner in Automatic mode from your remote control In the Automatic mode the standard temperature and the optimum fan speed is selected automatically You can adjust the standard temperature but
18. tion 1 Unit operation 2 Unit operation 3 Unit operation Power source 208 230V 60Hz Min Ampacity 6 0 B C 5 8 A B C 11 0 B C 6 2 A B C 11 6 Cooling Watts A 1350 B C 1300 AsB C 2450 B C 1380 2580 Refrigeration Lines Indoor unit A Unit B Unit C Unit Connections Flare Liquid Line O D 6 35 1 4 Suction Line O D 12 70 1 2 9 52 3 8 Factory Pre charge 50 162 Max Line length 150 491 Max Height Difference 70 23 Dimensions amp Weight WXHXD 790 x 245 x 165 31 92 62 1000 x 790 x 310 393 X313X 124 Net Weight 17 1543
19. ton the indoor unit beeps Sul vy 5 To control the direction of the air flow refer to page 15 On Timer Aff Timar Changing the Room Temperature Quickly 9 Si The Turbo cooling function is used to cool your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected 1 If necessary press the button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 Press the Get button Result The temperature and fan settings are adjusted automatically The air conditioner cools the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous mode temperature and fan settings But if you press the X amp C button in DRY FAN mode it will change to AUTO mode automatically 3 If you wish to stop the Turbo function before the end of the 30 minute period press the Gw button one or more times until mm or disappears Result The air conditioner is reset automatically to the previous mode temperature and fan settings 4 To control the direction of the air flow refer to page 15 Removing E
20. xcess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press On Off button Result The 5 Way indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the MODE button The air conditioner runs in DRY mode Note You can change modes at any time 3 To adjust the temperature press the TEMPERATURE buttons one or more times until the required temperature is displayed Possible temperatures are between 65 F 18 C and 86 F 30 C inclusive Result Each time you press the TEMPERATURE buttons The temperature is adjusted by 1 F 1 C The indoor unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically 4 control the direction of the air flow refer to page 15 On Timer Off Timer vey Turbo E Turbo ENGLISH
Download Pdf Manuals
Related Search