Saeco Coffee Makers Espresso Maker SUP 016 User's Manual
Contents
1. The keys W allow you to change the set options ON OFF If the second boiler is disconnected it is not possible to dispense st amand therefore cap puccino can t be prepared Should the cappuc cino selection button be pressed or the steany hot water knob be opened the display shows the following message PLEASE ACTIVADE SYSTEM 2 N E Water hardness adjustment Inorderto adjustthe waterhardness itis necessary to testthe water using the stip supplied with the machine Dip the stip into the waterfora second shake off excess water gently wait approx 1 minute and read the results Move the asterisk at the end of the line to the menu item WATER HARDN using the keys NV and select it by means of the ENT button The following message will be displayed 3 WATER HARDN HARDNESS 3 N The keys W allow you to change the set options HARDNESS 4 hard water HARDNESS 3 medium water HARDNESS 2 soft water HARDNESS 1 very soft water Cup heating plate connection Royal Cappuccino is equipped with a useful cup heating plate which can be disconnected if required Press keys NWVY to move the asterisk to item CUP HEATER Press ENT to activate this function The following message will be displayed 4 CUP HEATER y ON SOS IE UTA The keys AV allow you to change the set options ON or OFF Temperature selection W ith Ro2. standby to disactivate the energy saving mode Drainage Directthe steany hotwater spouton the drip tay 2 Place a cup or another suitable container under the dispensing tube then tum the steany hot water knob counterclockwise The pump starts automatically W aituntil a regularwaterjet is obtained then close the knob The machine is now drained and ready to work The following message will be displayed SELECT PRODUCT READY FOR USE E Important Itis advisable to drain the machine before the first start after a prolonged period the machine has not been used or whenever the water tank has been completely emptied Furthenmore should the pump be defective the display shows VENTILATE 1 Programming the machine 32 To enter the programming mode press the key ENT preground coffee when the machine is on and keep it pressed until the first two lines of the progranming mode are displayed 1 LANGUAGE 2 SYSTEM 2 At the end of the line a blinking asterisk is displayed which can be moved up and down with the keys AO tall and regular coffee Ifthe asteriskis on the firstmenu press button to move it on the second menu and vice versa The display shows the following sequence of messages 1 LANGUAGE 10 PROG H WATER 2 SYSTEM 2 11 PROG CAPPUC 3 WATERHARDN 12 TOTALCO FFEE 4 CUP HEATER 13 DESCAUN G 5 TEMP L COFFEE 14 SIGN DESCAL 6 TEMP COFFE
3. Switch off and unplug the machine if itwill notbe used for long periods Cut the supply power cord and deliver the machine to a public collecting point A Should the machine not be used anyrrore switch it off and unplug it A Keep the machine in a dry place far from the reach of children Should the machine not be used for a long period keep it from dust and dirt Maintenance Periodically check the machine working and clean it in accordance to the instructions Troubleshooting A In case of failure fault or suspected damage following a fall unplug the machine imvrediately To fix problems follow the instructions in the table Otherwise contact authorised personnel Only skilled personnel are authorised to repair the machine The user nightincur serious injuries should repairs not be propery camied out The manufacturer declines any liability whatsoever should repairs fail to be carried out according to the instructions contained in this manual Furthermore in these cases warranty rights cannot be honored M S PORTANT SAFEGUARDS IMPORTANT SAFEGUARDS W hen using your coffee maker basic safety precautions should always be followed in cluding the followed to reduce the risk of fire electric shock and or injury to persons including the following 10 Read all instuctions 20 Do not touch hot surfaces Use handles or knobs 30 To protect against electric shock do not place cord plug or appliance in w
4. Switch the machine on close the service door fit the coffee grounds containerand waituntil the machine resets
5. CAPPUCCINO 2 Saeco C HO USEHO LD USE ONLY W e congratulate for having bought this top quality espresso machine and thank you for choosing Saeco Before operating the machine we recommend to read the following instructions thouroughly which explain how to use clean and maintain the machine E DESCRIPTION OFSYMBOLS How to use the instructions These instructions cannotanticipate every possible use of the machine For further infonmation or questions conceming specific situations or problerrs please contact the local dealer or manufacturer directly A The waming triangle shows all important safety indications to ensure the user s safety The nonobservance of said instructions may cause serious injuries The first cover page of the manual shows figures relevant to the text Thus keep it open while reading the instructions Save these instructions carefully and make sure to hand them to other users B Reference to figures parts of the machine and control elements are given by numbers or letters as figure B exemplifies SAVE THESE INSTRUCTIONS A The lightning flash with arowhead symbol within an equilateral triangle is intended to alert the user to the presence of unisulated dangerous voltage within the products enclosure that may be of sufficient magnitude to consitute a risk of fire or electric shock to persons Table of contents Pa
6. Counter COUNTER LOCKING Xx After a certain number of cycles this function allows to stop the coffee dispensing excluding hot water seam and cappuccino dispensing operations Itcan also be used for example to program the machine servicing If the O value is set the function is disabled Fromthe VEN DING menu move the asterisk to the COUNTER menu by means of keys AW and confirm the selection through ENT Press the sarre keys to modify the selected value forexample to seta new servicing limit Through ENT a new value can be saved On the contrary by pressingESC the new value entering is stopped and as a result the former counter setting shall be considered W hen the setlinithas been reached the coffee dispensing stops and the following two messages are displayed COFFEE DISPENS BLOCKED SELECT PRODUCT READY FOR USE E Reset the counters by pressing the cappuccino selection key Dosage of ground coffee 33 The coffee dosage adjustment lever 18 allows the selection of the grinding coffee ammount from 6 to 9 grans Place lever 18 on the required position RECOMMENDATIONS Prolonged idleness If the machine hasn t been used for a prolonged ic TETAS period itis advisable for hygienic reasonsto run a rinse cycle through the machine Place a cup under the seam hotwater spout 7 and fill it with water by operating the hot water
7. fromthe rear side of the machine 30 Remove the cover 15 and fill the container with coffee beans 300 g approx then replace the cover Adjust grinding by means of the grind adjustrentlever 17 positioning iton point 5 of the scale A N ever fill the coffee bean container with other products since they mightdamage the machine A Before filling the container with coffee beans make sure the pre ground coffee container 14 is closed to preventcoffee beans fromfalling into it They might damage the machine Remove water tank 11 from the machine remove its cover 12 and fill it with cold water approx 2 41 A valve on the tank bottom prevents water from escaping Before installing the water tank in the machine make sure the coffee bean container cover is properly fitted 131 IE UTA 31 Install the water tank slightly pressing over it to fit the valve which will open automatically A Do not fill the tank with an excessive quantity of water A Always fill the tank with fresh water only hot water as well as other fluids night danage the tank Never use carbon dioxide added water A Do notswitch on the machine on ifthe water tank is empty always make sure there is enough water in the tank Connect the plug to the socket and press the main switch The following message will be displayed WARMING UP 7 Should ENERGY SAVING i be displayed press button
8. 2 m free flow themel cutout altemating piston pump electronic grinding adjustment device automatic coffee releasing device 0250 mM approx removable transparent tank electronic continuous approx 2 4 litres 300g bean coffee adjustable supplied with bum protection adjustable continuous approx 2 rin approx 20s cup approx 30s cup approx 605 cup approx 60 90s creany cup incorporated protection rangel see rating plate on the back of the machine EN 603352 15 96 EN 603352 14 96 EN 55014 inconpliance with the waranty certificate enclosed herein The manufacturer reserves the right to make inproverrents to the appliance due to technological advancement a NA Electrical parts should never be in contact with water danger of short circuit Steam and hot water may cause burns Never direct steam or water jets towards the body special attention mustbe paid when touching the steam hot water spout and the heating plate danger of burns This machine mustbe used exclusively for the purposes it has been manufactured Do not make technical changes for any reason whatsoever any improper use is forbidden due to the risks which might occur Warnings The machine shall only be used by adults and propery instructed persons Voltage Never touch parts under current They might cause electric shocks serious injuries a
9. 8 Forcappuccino dispensing fitsuction pipe 26 of the Cappuccinatore 25 ina milk container or in another container To prevent milk container deformation pierce iton the top to allow airentry Place the cup under dispenser 27 and press the cappuccino selection key Cappuccino dispensing can be adjusted by tuming the special Cappuccinatore adjustrrert valve 28 Note it is suggested to use milk with low fat amounts 1 5 Cappuccinatore cleaning Letthe C appuccinatore draina full watercontainer after each cappuccino dispensing in this way the device will be perfectly cleaned Incorporated safety devices Automatic off Should the service door be open the machine automatically switches off Ifthe central unitis not mounted only water and steam can be dispensed Electronic grinding time control As soon as the coffee bean container is empty grinding automatically stops after 20 seconds approx Fill the container with coffee beans as shown at page 80 Electronic pump control The machine switches off autorratically as soon asthe water inthe tankis underthe ninimumlevel checked by a special water level indicator 73 Fill the tank according to the procedure shown at page 80 Electronic temperature adjustment Said adjustrentcontols the correctterrperature to brew coffee and to dispense hotwaterand steam Coffee brewing isautorratically interrupted should the water temperature be excessive safety thenmostat and over
10. E 15 TIMER 7 TEMP S COFFEE 16 VEN DING 8 PREBREW ING 17 EXT 9 PREGRNDING To leave the menu move the asterisk at the end of the line to item lt lt EXx it gt gt using the key VY Then press ENT e preground coffee The machine is now in the normal mode again Selecting single menus Select the different menu itens by means of the E32 U PROGRAMMING THE MACHINE keys NY ThekeyENTallowsyouto activate the selected item Itis possible to modify the selected figuresina menuitemusing the keys AV Thekey ENT menoiizes the selected options for instance ON for the cup heating plate Should you accidentally change sore data press ESC to leave the menu item without saving the new options which were selected accidentally Language selection Move the asterisk to the menu item LANGUAGE using the keys AV Press ENT activate this item The following message will be displayed 1 LANGUAGI ENGLISH T E The keys allow you to change the set options ENGLISH ITALIANO FRANCAIS DEUTSCH NEERLANDAIS ESPANOL PORTUGUES Enabling of second heating system Royal Cappuccino is equipped with two boilers with independent circuits O ne of these boilers can be disconnected By pressing keys AV move the asterisk at the end of the line to the menu item SYSTEM 2 Press ENT to activate this item The following message will be displayed 2 SYSTEM 2 y ON
11. a 25 OH value which causes the waming light to switch on after 150 approx Should itbe necessary the water hardiness value may be exactly programmed following the instructions shown at page 82 The following adjustrents are possible Hardness 4 highwaterhardness over29 OH 14 dH i e 80 water approx Hardness 3 mediumwaterhardness approx 2029 OH 7 14 dH approx 150 water passage Hardness 2 soft water approx 12 20 dH 4 7 dH approx 300 water passage Hardness 1 very soft water less than 10 OH 3 dH approx 500 water passage Inhard water regions a filter should be used both to improve the coffee quality or to protect the machine thus reducing the descaling frequency Note for this purpose use a descaling product suitable for coffee machines Never use vinegar Descaling can be performed in two ways Automatic descaling Select this mode in the progranming menu see page 84 By means of keys NV move the asterisk at the end of the line on the menu itemDescaling and confirm the selection with the ENT key The following message will be displayed 13 DESCALING T Pour a discaling solution into the water tank according to the instuctions on the product package Switchthe machine onthe progranming mode Place a large container under the steany hot water spoutand open slowly the seamknob The automatic descaling starts Small amounts of descaling solution are pumped into the cir
12. a properly lit and hygienic room provided with accessible sockets leave a minimumdistance of 100 mmbetween the machine and the wall E Cleaning Before cleaning the machine make sure to switch off all keys and unplug the machine W ait until the machine cools down N ever plunge the machine into water Do nottamper with the inner parts of the machine and neveropenthe machine Repair maintenance Incase of defector suspected damage following a fall unplug the machine imvrediately Never use a defective appliance O nly skilled personnel are authorised to carry out repairs The manufacturer declines any liability whatsoever should repairs fail to be camed outby authorised personnel In case of fires use carbon dioxide CO2 extinguishers Never use water or powder extinguishers n 9 IMPORTANT SAFEGUARDS a A short power supply cord or detachable powersupply cord is to be provided to reduce risks resulting from becoming entangled in or tipping over a longer cord b Longer detachable powersupply cords or extension cords are available and may be used if care is exercised in their use c If a long detachable powersupply cord or extension cords is used 1 The marked electrical rating of the detachable powersupply cord or extension cord should be at least as great as the electrical rating of the appliance 2 If the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer c
13. ate this function The following message is displayed 9 PREGRINDING y ON The keys NV allow you to change the set options ON OFF Hot water programming Whenever this function is enabled the selected water amount is constantly dispensed On the contrary whenever this function is disabled hot water is dispensed until the user stops the dispensing Hot water amount can only be programmed with programming mode enabled PROG H WATER Press ENT to activate this function The following message will be displayed 10 PROG H WATER ON The keys W allow you to change the set options ON OFF Cappuccino programming Whenever this function is enabled the same amount of cappuccino is constantly dispensed On the contrary whenever this function is disabled cappuccino is brewed until the user stops the dispensing Cappuccino amount can only be programmed with programming mode enabled PROGRAMMING THE MACHINE Press keys NY to move the asterisk to item PROG CAPUC PresENT to activate this function The following message will be displayed 11 PROG CAPUC ON The keys AV allow you to change the set options ON OFF Coffee counter Press keys AV to move the asterisk to item TOTAL COFFEE and selectitby means of the ENT key The following message will be displayed 12 TOTAL COFFEE XX This value cannot b
14. ater or other liquid 40 Close supervision is necessary when any appliance is used by or near children 50 Unplug from the outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance 60 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Retum appliance to an authorised service facility for examination repair or adjustment 70 The use of an accessory not evaulated for use with this appliance may cause injuries 30 Do not use outdoors 90 Do not let cord hang over edge or table or counter or touch hot surfaces 100 Do not place on or near a hot gas or electric bumer or in a heated oven 11 0 Always atach plug to appliance first then plug cord into the wall outlet To disconnect tum any control to the off position then remove plug from wall outlet 12 Use this appliance only for its intended use as described in this manual 130 Keep the cord away from heated surfaces SAVE THESE INSTRUCTIONS RISK OF HRE OR ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF HRE OR ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REPAIR SHOULD BE DONE BY AUTORIZED SER ICE PERSONNEL ONLY 195 oe Trouble No message is displayed The autorratic coffee brewing does not start The autorratic coffee brewing does not start Steam and hot wa
15. ble damages to the machine Warning if the central unit is not correctly fitted the following message will be displayed BREW UNIT MISS The machine cannot dispense coffee Coffee grinder A N ever fill the coffee grinder with water it may imeparably damage the machine 45 Clean the coffee beans container periodically this operation should be accomplished by a qualified technician Unplug the machine Empty the coffee container and unloose the two fastening screws Now the container can be removed and cleaned 46 Carefully pull the adjustment lever upwards previously writing the set grinding degree 47 Tum the adjustment ring counterclockwise until the blue marks coincide 48 Now itis possible to remove the grinding ring from the machine slightly pulling it upwards 49 With the aid of a brush or a nanow vacuum hose clean both the gearbox and the grind ring support Make cure the position of the grind ring does notshift To reassemble the coffee grinder carry out the reverse sequence making sure the adjustment ring has not been shifted during cleaning If that is the case tum it until the blue mark coincide with one of the three notches Asserrble the grind ring support and make sure the blue marks coincide 50 Tum the adjustment ring clockwise to make the red marks coincide 51 Fit the adjustment lever on the ring until it coincides with the previously setgrinding degree Cappucci
16. cuit Then the pump stops to let the solution take effect During this phase the following message is displayed MACHINE IS i DESCALING Afterapprox 45 minutes when the procedure is accomplished the following message will be displayed DESCALING FINISHED Close the steam knob The pump stops Press ENT button A display message reninds youto rinse away any possible descaling residues from the machine RINSE MACHINE N E Remove water tank rinse it accurately and fill it with fresh water Clean the machine using the hot water knob and let the whole tank content flow out The following message will be displayed RINSING N FINISHED T Press the hot water key again Go back to progranming function by pressing tneENT key Note By pressing the ESC key itis possible to quit descaling procedure Reset descaling message Inprogranming function by pressing keys NV move the asterisktill the end of the line on the menu Sign Descal and confirm the selection with ENT button TU Descaung The following message will be displayed RESET DESCALING NO By means of the same keys NV itis possible to modify the value Yes or no Through this resetoperation the intemal counters of the two water systems are reset and the message DESCALE is erased If the function SIGN DESCAL N is selected without the displayed message D
17. d before can dispense two products at the same time During hot water dispensing only the programmed amount is dispensed if the corresponding progranming isenabled O nthe contrary dispensing should be stopped by pressing againthe selection key whenthe desired amount is reached Ifhotwateronly is dispensed dispensing isfaster than when coffee is dispensed atthe sare time To programthe hotwater amount itis necessary to keep the corresponding selection key pressed till the desired amount is reached Attention hot water can only be programmed if the corresponding programming function is enabled see page 83 During the progranming phase the following message will be displayed HOT WATER dl PROGR QUANTITY 36 Place a glass or cup under the steany hot water spout 7 then press the hot water selection key Hot water will be automatically dispensed Steam dispensing To heat milk or other drinks A Always clean the spout with a danp cloth soon after the use otherwise it night be difficult to remove milk residues A Aftera steamoutflow always drainthe machine By tuming steam knob 9 these two messages will be displayed STEAM ll READY FOR USE E SELECT PRODUCT READY FOR USE E This happens because the machine asmentioned before can dispense two products at the same time Direct seam hot water spout 7 on cup holder grill 3 and slightiy open
18. dosage of the coffee quantity according to the cup dimension The desired quantity Wee can be selected through the selection keys The relevantmessages will be displayed To set the quantity of coffee to be dispensed it is necessary to press the relevant selection key till the desired quantity of coffee is obtained max 250 m approx During this operation the following message is displayed 1 SMALL COFFEE PROG QUANTITY u The machine considers automatically the necessary amounts to brew two cups of coffee Attention Ifthe prebrewing functionisenabled during the cups dosage adjustment keep the selected key pressed even during the pump stop until the desired arrount is reached Double quantity of coffee or 2 cups of coffee By pressing one of the three selection keys twice before coffee dispensing begins the machine will brew a double portion of coffee Coffee grinding 34 This machine grinds a portion of fresh coffee for each cup for two cups itgrinds two portions of coffee one afterthe other thus ensuring optimum coffee quality Adjust the grinding degree according to the instructions mentioned at page 87 A Adjustthe grinding degree only when the coffee grinder is running Coffee dispensing Place one ortwo preheated cupsonthe cupholder grill 3 under the dispenser 6 By pressing the relevant selection key the machine will automatically dispense the selected coffee Dispensing ma
19. e machine during mail shipping Keep thispackage to retum the machine to the manufacturer whenever necessary Before installing the machine keep to the safety indications at page 77 W henever possible use the machine with swivel 24 W hen installing the machine make sure the swivel is always fitted inthe provided area on the lower side of the machine Power supply connection A Warning electric curent may cause death Always keep to safety rules The coffee machine must be connected to an adequate socket Voltage mustsuitto the voltage specified on the appliance rating plate A Never use defective power cords Defective power cords and plugs must be replaced by an authorised personnel A Should an extension cord be used check its perfectconditions The extension cord musthave a minimum sectionof 1 5 nm or 16 AWG and must be supplied with a three pole plug socket Starting and use NA Parts under current shall never be in contact with water danger of short circuit Overheated steam and hot water may cause burns Do not direct steam or water jettowards the body furthermore great attention must be given when touching eitherthe stea m hot water spout or the heating plate danger of burns A N ever use the machine without water or coffee beans Rerrove measuring spoon brush and the central unit key from the coffee grounds container 1 and keep them within reach Unwind the power cord 5
20. e asterisk to item VENDING and select it through the ENT key From the displayed submenu it is possible to select one of the following itens by mearsofthesamekeys W Onthecontary if the hot water selection key is pressed the submenu can be quit The following messages will be displayed CODI AA AM El 1 LARGE COFFEE e PROGRAMMING THE MACHINE T SMALL COFFEE O AL HOT WATER TOTAL COUNTE LOCKING i COUNTER i CYCLES y Code programming A code protects the access to the machine counters enter it for each progranming section and before carrying out any modification As soon as the code is entered modifications can be camied out without entering it again as long as the programming function is enabled The machine is not supplied with a code Keep to the following indications for code progranming By means of keys AVY move the asterisk to item VEN DING and selectitthrough theENT key The following message will be displayed CODE AA AM By means of keys enter the number to be seton the first character and confirm the selection through the ENT key The entered number is saved and the cursor moves automatically to the following character After having entered the complete new code it is necessary to save it The following message will be displayed NEW CODE XXXX
21. e modified Q uitthe menu by means of the ENT or ESC keys Descaling Move the asterisk at the end of the line to menu item Descaling and selectitby means of the ENT key The following message will be displayed 13 DESCALING For descaling procedure see page 92 Timer The timer enables the automatic switching off of the machine after a preset period which can be set from 15 minutes to 12 hours after last dispensing If after a few seconds coffee is brewed again the timer is reset If the value set is0 00 thetimerfunctionis notactivated and the machine does not switch off M ove the asterisk at the end of the line to menu item Timer by means of the keys AV Press ENT to select this item The following message will be displayed STANDBY AFTER 0 00 By means of the same keys AV select the suitable time and confirmthe value throughEN T button W hen the selected time is over the following message is displayed ENERGY SAVING f The machine stops and can be switched on again by means of button Q standby Vending functions Royal Cappuccino is equipped with a counter allowing the machine statistic analysis while detecting the different dispensing operations It is also equipped with another counter which is able to stop the dispensing operations after a certain number These functions are protected by a special access code By means of keys AWY move th
22. el SAVE NO By means of keys AW the code can be saved or not saved YES orNO Code entering To enter the code press keys Y and move the asterisk to the counter to be changed select it through the ENT button The following message will be displayed CODE Enter the number to be set on the first character by means of keys and confirmthe selection with ENT The entered number is then saved and the cursormovesautomaticallyto the following character If a wrong code has been entered the following message will be displayed for about two se conds CODE FAULTY s After having entered three wrong codes the entering procedure is not allowed any longer Counter modification Large coffee counter 1 LARGE COFFEE TOTAL XX The counter shows the large coffee amount dispensed from the last reset Fromthe VEN DING menu nove the asteriskto the LARGE CO FFEErrenu by mearsofkeys AV corfinmthe selection with butonENT By means of the sarre keys AV it is possible to modify the selected value to resetthe counter for example Use the ENT button to save a new value Press the ESC button to stop the new value entering procedure and as a result the fonmer counter setting shall be considered Coffee counter 1 COFF TOTAL Xx T T The counter shows the regular coffee amount ki RECOMMENDATIONS dispensed from the last reset Fromthe VEN DIN G m
23. enu move the asteriskto the COFFEE menu by means of keys AV confirm the selection through ENT By means of the same keys AV itis possible to modify the selected value to resetthe counter for example Press ENT to save a new value Onthe contrary by pressing ESC the new value entering is stopped and as a result the former counter setting shall be considered Small coffee counter T SMALL COFFEE TOTAL xx The counter shows the small coffee amount dispensed from the last reset Fromthe VEN DING menu move the asterisk to the SMALL COFFEE menu by means of keys AV confirmthe selection throughEN T By means of the sarre keys AV itis possible to modify the selected value to resetthe counter for example Press ENT to save a new value Onthe contrary by pressing ESC the new value entering is stopped and as a result the former counter setting shall be considered Hot water dispensing counter HOT WATER TOTAL DON The counter shows the hot water amount in m dispensed from the last reset Fromthe VEN DIN G menu move the asteriskto te HOT WATER menu by means of keys AV confirmthe selectionthroughENT By rreans of the sarre keys AV itis possible to modify the selected value to resetthe counter for exanple PressENT to save a new value Onthe contrary by pressing ESC the new value entering is stopped and as a result the fonmer counter setting shall be considered
24. escale the following message will be displayed QUANTITY WATER NOT REACHED N E Standard descaling Switch offthe machine Poura descaling solution into the water tank according to the instuctions onthe productpackage Place a large container under the steany hot water spout 7 Switch the machine on by pressing the main switch press the hot water key and let the descaling solution inthe watertank pour outof the spoutfor 1 minute approx Press hot water key to complete the operation Switch the machine off and letthe solution taking effectfor5 minutes approx Repeatthis procedu re two or three times to empty the water tank Assoon as descaling has been performed rinse the watertank 1 1 thoroughly and fill itwith fresh water Switch on the machine again and let water 2 approx flow out of the steam hot water dispensing tube in order to rinse away residues Important A periodic descaling ensures a correct machine functioning and avoids expensive repairs The machine warranty does not cover damages occuning asa result of the non observance of descaling procedures improper use and non observance of any other instruction contained herein Maintain the manufacturer s adjustmentif the water hardness degree is not known Disposal Machines which are no longer operational should immediately be made non serviceable by cutting the power cord Machines should be delivered to a public disposal centre
25. ge 75 Technical data 77 Safety rules 79 Machine controls and parts 79 Description of the control panel 80 Unpacking Installation 80 Power supply connection 80 Starting and use 81 Drainage A The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance rvicing instructions in the literature accompanying the appliance Page 82 Programming the machine 86 Recontrendation 87 Grind adjustment 88 Brewing 90 Incorporated Safety Devices 91 Cleaning and maintenance operations 94 Disposal 95 Troubleshooting cnc aa Voltage rating N ominal power Dimensions length x width x height Machine case W eight Cable length System Temperature control Coffee grinder adjustment Coffee grounds ejection Ground coffee dosage Cup progranming W ater tank W ater regulation Capacity water tank bean coffee container Steam hot water dispensing tube Steam hot water dispensing Heating tine Brewing tine espresso coffee coffee hot water milk Cappuccino Overheating protection Insulation Approvals In compliance with EN regulation W ananty Accessories included in the machine price Measuring spoon Central unit key Cleaning brush W ater hardness detecting strips see rating plate on the back of the machine see rating plate on the back of the machine approx 385 x 330 x 395 nm metal and plastic material approx 16 kg approx 1
26. heating safety device activated Antigravel device Even selected coffees may contain inpurities To avoid damages the coffee grinder is fitted with an antigravel device against impurities Should gravel end up into the coffee grinder you will hear a strong and characteristic noise Stop the machine immediately otherwise the machine will automatically stop within 20 seconds thanks A 9 1 CLEANING AND MAINTENANCE OPERATIONS to the special electronic protection system Important Do not start the machine before the foreign body has been removed otherwise the motor may be damaged Procedures see page 92 points 4549 Cleaning and maintenance operations General deaning To ensure a good coffee quality and a longer working life always keep the machine clean A Before cleaning the machine tum off the nain switch unplug the machine and wait until it cools down A Do notintrerse the machine into water or other fluids it may be imeparably danaged A Do not wash parts of the machine in the dishwasher A Always handdry all parts of the machine do not dry themin the oven or nicrowave oven Water tank drip tray coffee grounds container and coffee dispenser 39 In orderto keep the service area and the central unit 22 clean daily empty the coffee grounds container 1 after machine use The watertank 11 drip tray 2 cup holder grill 3 and coffee grounds container 1 should be washed periodically us
27. ing a nonabrasive solvent and drying them carefully 40 Coffee dispenser 4 may be removed forcleaning operations Unloose the screws and rinse the dispensing tube thoroughly with hot water Fromtirre to time clean the machine casing with a damp cloth and dry it Clean pre ground coffee container 14 with the aid of the brush supplied whenever necessary Central unit Clean central unit 22 whenever the coffee bean container is filled oratleastonce a week Switch off the machine and open service door 19 Remove grounds coffee container 1 41 Remove central unit 22 by holding the handle and shortly pressing the PRESS key W ash the central unit with hot water do not use any solvent 42 Make sure there are no coffee residues on the two steel filters the upper filter can be removed by unloosening and tuming the plastic pin anticlockwise using the tool supplied Dry thoroughly each central unit component fit the filter again and tighten it properly with the screw 43 Remove coffee rest drawer 23 and clean it using a nonabrasive solvent Clean the service area thoroughly and fit the coffee rest drawer again 44 By holding the central unit by its handle slide it back into its original position making sure itis correctly engaged Then close the door Fit the coffee grounds container again A When fitting the central unit do not press PRESS button it may cause 1 O 2 II TT irrepara
28. knob Preheating cups Cups may be preheated by placing themon the special cup heating plate Temperature led When starting the machine the following message is displayed WARMING UP As soon as the operating temperature has been reached the following message is displayed SELECT PRODUCT READY FOR USE E Empty coffee bean container W hen coffee beans run out the coffee grinder stops and the following message is displayed COF BEANS EMPTY Fill the container and restart the cycle Empty water tank When water runs out the program stops automatically and the following message is displayed WATERTANK EMPTY Fill the tank and restart the cycle Grounds container warning light Assoonasthere are 30 groundsin the container the following message is displayed DREGDRAWER FULL READY FOR USE N The machine does notstop remove the grounds container and enpty it Grind adjustment If the coffee flows too quickly Coarse grind or too dowly fine grind into the cup adjust coffee grinder The recommended grind level is position 5 Should grinding be too coarse adjust iton a lower value e g from5 to 3 On the contrary should grinding be too fine adjustiton a higher value e g from5 to 7 A Adjust the grind level only when the coffee grinderis running Avoid any extreme adjustment for instance on position 1 wheneve
29. knob 9 tuming it counterclockwise W ait until the remaining water has flown out of the spout Then move the spout outwards and plunge it deeply into the fluid to be heated 37 Slowly open the steany hotwater knob and heat the fluid with a circular moverrent from the bottom to the top W hen the fluid has reached the desired tenpe SOQ IE TEA rature close the knob and immediately clean the spout with a damp cloth Attention the spoutis hot itrray cause bums Cappuccino Through the special Cappuccinatore thismachine canbrew a real cappuccino withoutany problem By pressing the cappuccino button these two messages will be altemately displayed CAPPUCCINO N READY FOR USE y E SELECT FOR USE READY FOR USE N E That is because the machine as mentioned before can dispense two products at the same tine USER MAINTENANCE INSTRUCTIONS INCORPORATED SAFETY DEVICES During the cappuccino dispensing only the programmed amount is dispensed if the corresponding programming is enabled O nthe contrary dispensing should be stopped by pressing againthe selection key when the desired Cappuccino amount has been reached To program the cappuccino amount it is necessary to keep the corresponding selection key pressed till the desired amount is reached Attention cappuccino amountcan only be programmed if the corresponding programming function is enabled see page 83 3
30. natore 52 To quickly clean the cappuccinatore inmerse the suction pipe into warm water and let water flow through it For a more accurate cleaning remove the cappuccinatore and open cover 29 Clean the outside part with warm water and rinse it with cleaned water Descaling Attention The descaling operations mus be carried out when the machine components are cold Descaling removes limescale from all surfaces and holes thus ensuring a perfect operation of valves heating controls and other important parts Note due to the complexity of the coffee machine hydraulic circuit the following descaling cycles autorratic and standard do notallow the descaling of all tubes In fact easily accessible components such as the central unit 22 and its plastic connection are excluded The machine mustbe descaled every 3 4 months depending on the water hardness degree A rrore frequent descaling is recommended wherever the water hardness degree is very high To avoid dangerous delaysto users this machine is supplied with a special control counter reninding the user to perform this operation according to the water hardness degree scan In this case the following message will be displayed DESCALING W hen this message is displayed the machine doesnotstop however itissuggested to descale quickly the machine To cancel the message see programming menu indications point 14 The machine has been adjusted on
31. nd death The machine mustbe connected to a socket with suitable voltage Voltage must correspond to the voltage shown on the appliance rating plate A Power cord N ever use the machine with a defective power cord Replace defective power cords and plugs contacting authorised personnel Do not extend the power cord around comers sharp edges or over hot parts and protectit fromoil Do not shift or move the machine by pulling its power cord Do notunplug the machine by pulling the power cord and never touch it with wet hands Make sure the power cord does nothang fromtables or shelves B Keep children away Do notallow children to play with the machine Children are not aware of the potential danger caused by electric appliances SAFETY RULES Positioning Place the machine on a plane surface where nobody can tum it upside down or be hurt Hot water or overheated steam might escape from the machine danger of bums Never use the coffee machine outdoors or inside rooms with low temperature conditions Do not place the machine on hot surfaces or in the proximity of open flames to avoid possible damages of the case C Danger of burns Do not direct the overheated steamor hot water jettowards youor other people Do nottouch hot surfaces such as the steany hot water spout D Necessary space For a proper operation of the machine it is advisable to keep to the following indications choose a levelled surface choose
32. ord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over 1 Coffee grounds container 16 Coffee bean container 2 Drip tay 17 Grind adjustrrent lever 3 Cup holder surface 18 Coffee dosage adjustment lever 4 Main switch 19 Service door 5 Power cord 20 Filling funnel 6 Coffee dispensing unit 21 Handle for assembling and disasserrbling 7 Steam hotwater spout wit bum protection of central unit 8 Control panel 22 Central unit 9 Steamknob 23 Coffee rest drawer 10 Cup heating plate 24 Swivel 11 Water tank 25 Cappuccinatore 12 Water tank cover 26 Suction pipe 13 Water level 27 Dispenser 14 Preground coffee container with cover 28 Cappuccinatore adjusting valve 15 Coffee bean container cover 29 Cappuccinatore cover Description of the control panel a z Digital display f Standby switch WARMING UP energy saving function ory off pa 2 N inthe programming mode Selection key for 1 or 2 cups of regular coffee or key w in the programming mode 0 Selection key for 1 or2 cupsoftall coffee orkey E E O Selection key for 1 or 2 cups of espresso coffee or ESC in the programming mode Pre ground coffee selection button or ENT in the programming mode Cappuccino selection key Hot water or off key 130 IE TA Unpacking installation Standard packing is strong enough to protectth
33. r possible Itis preferable to try another coffee blend since not all coffee blends are suitable Coffee blends Make sure coffee is fresh An espresso roast is preferable In order to obtain a strong and aromatic espres so coffee use special blends suitable for espres so coffee machines and special cups with thick sides Keep coffee in a cool place in an henretically sealed container Operation time The machine may be kept on all day long However in case of a prolonged period of idleness it is advisable to enable the energy saving function by pressing the standby switch If the timer is properly prograntred this operation is automatic for this purpose see page 84 In case of a prolonged period of idleness it is advised to switch the main switch 4 off once switched on again the machine will be ready to be used within two minutes Switching off the machine Switch the machine off only afterthe coffee cycle has been concluded E OS IE TN BREWING Royal Cappuccino is equipped with 2 indepen dent heating systems which may dispense atthe same time coffee and hot water coffee and steam or coffee and cappuccino If during the dispensing of 2 coffees hot water steamor cappuccino are dispensed atthe same time it may happen that the second coffee portion is not immediately ground after the first one but only at the end of the first coffee dispensing Cup level filling This machine allows the precise
34. ter are not dispensed Coffee is dispensed too quickly Coffee is dispensed too slowly Coffee is not hot enough Coffee is not creamy enough The machine coffee brewing is reduced it takes longer to heat and the dispensing isnotsufficient The central unit cannot be removed Possible causes The machine is notgetting power The service door is open GE BREW UNITMISS CEEE ATA BREW UNITBLOCK O WATERTANK COF BEANS EMPTY EMPTY d LE DREG DRAWER MISS C SD GRIN DER BLO CKEDI ETA The steam hot water spout hole is clogged Grinding too coarse Grinding too fine The central unit filter is clogged The cup has not been preheated The coffee blend is not suitable or is not fresh Grinding is not correct too fine or too coarse Descaling the machine The central unit has not been correctly positioned Solution Tum the main switch on check plug and fuse Close the service door is Properly fit and lock the central unit Clean the central unit see page 91 Fill with water or coffee beans and restart the cycle Fitthe coffee grounds container properly Service the coffee grinder see page 92 Clear the hole with the aid ofa thin needle Adjust the grinder on a finer grinding e g from5 to 3 Adjustthe grinder on a coarser grinding e g from5 to 7 Clean the filter Heat the cup on the heating plate Try another coffee blend Descale the machine as described at page 92
35. y be intemupted by pressing one of the coffee selection keys ifan excessive water amount has been selected Should you interrupt the coffee flow after the first of two coffees the second is not dispensed Pre ground coffee A Make sure to use pre ground coffee only medium ground Never use whole beans or soluble coffee A Right before brewing coffee fill the container with freshly ground coffee For bestresults make sure coffee blend is fresh Remember that ground coffee ages soon thus losing its quality 35 Important Use the measuring spoon supplied to fill the container 14 with a single portion of ground coffee Use a full measure only To dispense coffee press pre ground coffee button e and the desired selection key large E O O IE BREWING coffee coffee small coffee to obtain a cup of coffee Important This function does not allow the double coffee cycle Dispensing may be intemupted by pressing one of the coffee selection keys ifan excessive water amount has been selected Hot water dispensing Hot water dispensing is accomplished through an independent water circuit which ensures the correct temperature and supplies tasteless hot water to be used for tea soup etc By operating the hotwater key the following two messages will be displayed HOT WATER READY FOR USE y SELECT PRODUCT READY FOR USE d This happens because the machine asnentione
36. yal Cappuccino a precise adjustrent of the coffee tenperature can be executed Move the asterisk atthe end of the line to the menuiters Temp I coffee Temp coffee or Temp s coffee and selectit by means of the ENT key Depending on the selection the following messages will be displayed 5 TEMP L COFFEE EDIUM 6 TEMP COFFEE EDIUM 7 TEMP S COFFEE The keys XV allow youto change the setoptions Minimum maximum high medium or low Prebrewing function As soon as the coffee has been moistened the pump stops fora while in order to allow a better utilization of the coffee powder Move the asterisk at the end of the line to the menu item PREBREWING and select it by rreans of the ENT key The following message will be displayed 8 PREBREWING ON The keys W allow you to change the set options ON OFF LONG in the latter Case the pump stop is longer Pre grinding function By activating this function grinding occurs every time the doser is empty So a ground coffee portion is always ready in the doser allowing a time saving whenever the machine is often used This function is not recommended in all other cases because fresh ground coffee is by far better Press keys NY to move the asterisk to item PREGRIN DING Press ENT to activ
Download Pdf Manuals
Related Search