Home

Runco SC-50D User's Manual

1. 7 AutoScope Carriage Plate Figure 3 23 Anamorphic Lens Mounting Assembly Exploded View Signature Cinema SC 50d SC 60d Installation Operation Manual 45 Installation Attach Lens Mounting gt Assembly to Lens Motor Carriage Plate is Remove the two Yaw X Adjustment Levers item 8 from the bottom of the Anamorphic Lens Holder item 5 Place the Anamorphic Lens Holder on top of the AutoScope Carriage Plate item 7 Position the bracket so that the long slot at the bottom of the lens holder is perpendicular to the corresponding slots on the plate Secure the Anamorphic Lens Holder to the plate using the Hex Bolts Washers item 6 and Yaw X Adjustment Levers that you removed in Step 1 Use the Lens Mounting Screws to attach the Lens Adapter Ring item 1 to the Pitch Adjustment Yoke item 2 see Figure 3 24 Use the round threaded holes on the yoke Use the Height Y Adjustment T Screws Washers item 3 Pitch Adjustment T Screws Washers item 4 and T Nuts item 9 to attach the Pitch Adjustment Yoke and Lens Adapter Ring to the Anamorphic Lens Holder The Yoke should be as close to the primary lens as possible Attach the lens to the Lens Adapter Ring by threading it clockwise Lens threads into ring Figure 3 24 Attaching the Anamorphic Lens to the Lens Ring 46 Signature Cinema SC 50d SC 60d Installation Operation
2. OHEIGHT 50 50 YES Sets the value for output height OHEIGHT NA NA Returns output height value OHPOS 50 50 YES Sets the value for output horizontal posi tion OHPOS NA NA Returns output horizontal position value OVPOS 50 50 YES Sets the value for output vertical position OVPOS NA NA Returns output vertical position value OWIDTH 50 50 YES Sets the value for output width OWIDTH NA NA Returns output horizontal width value 88 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 6 1 Serial Commands continued Command Parameter Manor Description min max Stored P Sleep Timer Commands SLEEPTMR NA NA Returns sleep timer setting STOFF NA YES Sets the sleep timer to Off ST30MIN NA YES Sets the sleep timer to 30 minutes ST60MIN NA YES Sets the sleep timer to 60 minutes ST90MIN NA YES Sets the sleep timer to 90 minutes ST2HRS NA YES Sets the sleep timer to 2 hours ST4HRS NA YES Sets the sleep timer to 4 hours Miscellaneous Commands DISPLAY NA NA Returns display device input source value as follows 1 Auto 51 SC 50d SC 60d INRES NA NA Returns input resolution MACADDR NA NA Returns DHD Controller MAC address MODEL NA NA Returns product model name OUTRES NA NA Returns output resolution SERNUM NA NA Returns DHD Controller serial number SWVER NA NA Re
3. Figure 2 2 shows the SC 50d SC 60d rear input panel O o 7 EE ofe C o p GS wm O 6 Oo Tee dE 0 Om Uu l m Figure 2 2 SC 50d SC 60d Input Panel 6 Signature Cinema SC 50d SC 60d Installation Operation Manual Controls and Functions 1 RS232 IN Connect the RS 232 output from the DHD Controller here using the provided RJ11 to DB9 adapter and communication cable 2 PWRLED Lights green to indicate that power is applied and the module is initialized During normal operation always on 3 1 Dual Link DVI I Input Slot 2 HDCP compliant digital video input Connect the HDMI output from the DHD Controller to this input See Figure 2 4 4 Analog LED Lights briefly when the projector is powered up self test During normal operation always off 5 Digital LED Lights green to indicate that a valid digital signal from the DHD Controller is present 6 MAIN POWER SWITCH Disconnects or applies power to the SC 50d SC 60d 7 POWER INPUT 100 to 240 VAC Connect the projector to power here Use ONLY the AC power cord s
4. Rear Screen Inverted Mount ceiling Installation Projector is completely hidden Usually good ambient light rejection Requires separate room nstallation cost is usually higher Rear Screen Floor Mount with Mirror Projector is completely hidden Usually good ambient light rejection Requires less space behind screen than other rear screen installations Requires separate room nstallation cost is usually higher In general minimize or eliminate light sources directed at the screen Contrast ratio in your images will be noticeably reduced if light directly strikes the screen such as when a shaft of light from a window or floodlight falls on the image Images may then appear washed out and less vibrant Signature Cinema SC 50d SC 60d Installation Operation Manual 17 Installation 3 3 Installation Considerations lt Installation Type Ambient Light Installation Throw Distance y Throw distance is the distance measured from the front of the projector to the screen This is an important calculation in any projector installation as it determines whether or not you have enough room to install your projector with a desired screen size and if your image will be the right size for your screen You can quickly estimate the throw distance by taking the width of the screen and multiplying it by the lens throw ratio see Figure 3 1 The result of this calculation tells
5. a Camnnnenu SCART Figure 2 4 DHD Controller Rear Panel 1 MAIN POWER SWITCH Disconnects or applies power to the DHD Controller TRIGGERS Connection for up to three 3 12 volt trigger controlled devices such as retractable screens or screen masks Output current is limited to 250 milliamperes mA USB A standard USB Series B connection to a personal computer for performing software upgrades and other service procedures Signature Cinema SC 50d SC 60d Installation Operation Manual 9 Controls and Functions RS 232 To Accessory Box A male 9 pin D sub connector for interfacing with external equipment For future use Display Control Connect this to the RS 232 input on the SC 50d SC 60d projector IR Wired input from a Niles or Xantech compatible infrared IR repeater system It is a 3 5 mm mini phono jack wired as follows Ring No connection Tip IR Input Sleeve Ground POWER INPUT 100 to 240 VAC Connect the DHD Controller to power here HD1 HD2 5 x Analog BNCs Two inputs five BNCs per input for connecting standard definition SD 480i 576i enhanced definition ED 480p 576p or high definition HD 720p 1 080i 1 080p component video sources or RGBHV sources such as personal computers Component SCART 3 x RCA connectors SD HD input for connecting SDTV EDTV or HDTV component video sources Also provides RGB input for SCART RGBS sources Video 1 Video
6. e EN 61000 3 2 Electromagnetic compatibility EMC Part 3 Section 2 Limits for harmonic current emissions equipment input current up to and including 16 A per phase 2000 e EN 61000 3 3 Electromagnetic compatibility EMC Part 3 Section 3 Limitations of voltage changes voltage fluctuations and flicker in public low voltage supply systems for equipment with rated current up to and including 16 A and not subject to conditional connection 1995 Council Directive 2006 95 EC and amended by M1 and C1 on Low Voltage Equipment Safety EN 60950 Safety of information technology equipment including electrical business equipment The Technical Construction file required by this Directive is maintained at the corporate headquarters of Runco International LLC located at 1195 NW Compton Drive Beaverton OR 97006 1992 Date of Declaration March 201 1 viii Signature Cinema SC 50d SC 60d Installation Operation Manual NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a part
7. none of the other pins are used Figure 3 17 RS 232 Control System Connection to DHD Controller Signature Cinema SC 50d SC 60d Installation Operation Manual 37 Installation Connecting 12 volt Trigger Outputs to External Equipment If you are installing an SC 50d CineWide with AutoScope or SC 60d CineWide with AutoScope connect the AutoScope lens motor to a 12 volt trigger output on the DHD Controller see Figure 3 18 Similarly connect other 12 volt trigger activated equipment such as retractable screens or screen masks to the other trigger outputs AutoScope Lens Motor fe d Power AC Input Switch H 3 5 mm mini plug Retractable Screen or other 12 volt trigger activated device Sleeve Ground e _ Tip 12V Figure 3 18 Connecting 12 volt Trigger Outputs 38 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation Connecting an External IR Receiver to the DHD Controller If infrared signals from the remote control cannot reach the DHD Controller due to excessive distance or obstructions such as walls or cabinet doors you can connect an external IR receiver to extend the range of the remote control See Figure 3 19 IR Sensor Remote Control QR Repeater 3 5 mm mini phono plug RS 232 Display Control gt R AS 9 HDMI Out 3 To Display 5 Reza gt HDMI Out PC Control 4 Etheme
8. CEC Version Ox9E y Set OSD Name 0x47 y Menu Status Ox8E y Report Power Status 0x90 y Set Menu Language 0x32 y 94 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 6 3 CEC Commands Supported by the DHD Controller continued Supported V Yes No Opcode Value Initiator Follower Give Physical Address 0x83 Y Set Stream Path Ox86 Y Get CEC Version Ox9F y Abort Message OxFF y User Control Pressed 0x44 y User Control Released 0x45 y Give OSD Name 0x46 y Menu Request Ox8D y Give Device Power Status Ox8F y A Note The DHD Controller does not transmit HDMI CEC control messages from the HDMI Audio Out connector Signature Cinema SC 50d SC 60d Installation Operation Manual 95 External Control External Control Notes 96 Signature Cinema SC 50d SC 60d Installation Operation Manual Specifications 7 Specifications Table 7 1 lists the SC 50d SC 60d projector specifications Table 7 1 SC 50d SC 60d Projector Specifications Projector Type Native Resolution Lamp Life Aspect Ratios DTV Compatibility Picture Size 16 9 Screen SC 50d Picture Size 16 9 Screen SC 50d Processing Control Options Inputs Video Standards Calibration Throw Distance Factor x Screen Width Horizontal amp Vertical Offset Light Output Contrast Ratio
9. This symbol found on your product or on its packaging indicates that this product should not be treated as household waste when you wish to dispose of it Instead it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences to the environment and human health which could otherwise be caused by inappropriate disposal of this product The recycling of materials will help to conserve natural resources This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal Signature Cinema SC 50d SC 60d Installation Operation Manual ix Notes X Signature Cinema SC 50d SC 60d Installation Operation Manual Table of Contents RuncoCare Standard Two Year Limited Warranty eeeceeeeeseeseeneeneeeeeeeeeeee iii Important Safety Instructions 22 2 eccccecesessnneneeceeeeeeeeeeeensensnneeeeeeeeeseseeensesnnaneneeeeenes vii Compliance Information nmmnicccccnnnnnnnnnnnnan cnc viii Te Introduction E 1 About This Manual 5 ett tn eim net Hs 1 Target AUN 2i eet eed a ter dep EROR HR te e ECHTE ED te GN 1 If You Have Comments About This Manual ssec 1 Textual and Graphic Conventions oooooococonooncncccnnconnnonanonan aa a a aa 1 Hsing THa Mant
10. e Remote and built in keypad button identifiers are set in upper case bold type for example Press EXIT to return to the previous menu e Computer input commands you type and output responses that appear on screen is shown in monospace fixed width type for example To change the aspect ratio to Letterbox type LETTERBOX lt Enter gt e All keys with functional names are initial capped set in bold type and enclosed in angle brackets These keys are the following lt Enter gt lt Spacebar gt lt Control gt lt Esc gt and lt Tab gt e Enter indicates that you may press either the RETURN or ENTER key on your keyboard if it has both keys In addition to these conventions underlining boldface and or italics are occasionally used to highlight important information as in this example Nos A carriage return must be used after each command or string A ote Signature Cinema SC 50d SC 60d Installation Operation Manual 1 Introduction 1 2 Using This Manual Graphic Conventions These symbols appear in numerous places throughout the manual to emphasize points that you must keep in mind to avoid problems with your equipment or injury TIPS highlight time saving short cuts and helpful guidelines for using A Tip certain features NOTES emphasize text with unusual importance or special A Note significance They also provide supplemental information degrade performance or cause a mal
11. Composite 2 Composite 1 DOWN BUTTON Use to direct select aspect ratios or move the OSD menu cursor down When no menu is present on screen this button toggles through the different aspect ratios in this order 16 9 4 3 Letterbox VirtualWide Cinema Virtual Cinema Native 8 Signature Cinema SC 50d SC 60d Installation Operation Manual Controls and Functions 7 RIGHT BUTTON Used to direct select inputs or move the OSD menu cursor to the right When no menus are present on screen the RIGHT button toggles through the different sources in this order Composite 1 Composite 2 Composite 3 Component HD 1 HD 2 SCART HDMI 1 HDMI 2 HDMI 3 HDMI 4 8 MENU BUTTON Press the MENU button to bring up the main menu or to exit the current menu and return to the previous one 9 UP BUTTON Use to direct select aspect ratios or move the OSD menu cursor up When no menus are present on screen the UP button toggles through aspect ratios in the following order Native Virtual Cinema Cinema VirtualWide Letterbox 4 3 16 9 10 ENTER BUTTON When an item is highlighted on the OSD the ENTER button selects the item 11 STANDBY LED Lights amber when the DHD Controller is in standby mode otherwise it is off Figure 2 4 shows the rear connector panel on the DHD Controller 2 4 DHD Controller Rear Panel
12. 108 EC on Electromagnetic Compatibility EN 55022 Limits and methods of measurements of radio interference characteristics of information technology equipment 1998 EN 55024 Limits and methods of measurements of immunity characteristics of information technology equipment 1998 Including e EN 61000 4 2 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 2 Electrostatic discharge immunity test e EN 61000 4 3 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 3 Radiated Radio Frequency Electromagnetic Field Immunity Test e EN 61000 4 4 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 4 Electrical fast transient burst immunity test e EN 61000 4 5 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 5 Surge immunity test EN 61000 4 6 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 6 Conducted disturbances induced by radio frequency fields immunity test EN 61000 4 8 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 8 Conducted disturbances induced by power frequency magnetic fields immunity test e EN 61000 4 11 Electromagnetic compatibility EMC Part 4 Testing and measurement techniques Section 11 Voltage dips short interruptions and voltage variations immunity tests And
13. Cinema SC 50d SC 60d Installation Operation Manual Installation If you are installing an SC 50d CineWide with AutoScope or SC 60d CineWide with 3 12 AutoScope proceed as follows to install and adjust the secondary anamorphic lens Installing and Adjusting the It is extremely important that the primary lens is properly CineWide Anamorphic A Note adjusted before you install the anamorphic lens Ensure that Lens the image from the primary lens is perfectly centered on the screen The SC 50d SC 60d Anamorphic lens mount kit consists of everything shown in Figure 3 23 Some components shipped with your projector may differ slightly from what is shown in these instructions If any items are missing or damaged please contact your Runco dealer or Runco Customer Service at 800 23 RUNCO 1 Lens Adapter Ring and Mounting Screws 3x 10 Anamorphic Lens a e Set Screw 9 Pitch Adjustment T Nut 2x L e gs CES Pitch Adjustment Yoke for L ili i nO 2 itc justment Yoke for Lens i it ee 3 Height Y Adjustment E O q T Screw and Washer te 6 4 Ll L g 2x ji Pitch Adjustment T Screw and es Washer Ex 6 Anamorphic Lens Holder 8 Yaw X Adjustment Lever 2x i 6 1 4 20 Hex Bolt 2x and Washer 2x
14. Cinema SC 50d SC 60d Installation Operation Manual Operation Height Select Height from the Inout Position menu to change the projected image height Press p gt to increase the height press to decrease it Overscan Overscan Mode Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area Overscan effectively trims away these inactive outer edges and enlarges the remaining portion of the image to fill the display area For HDTV DVDs and other video sources Overscan is generally not necessary or desirable This control defines the amount of overscan applied to the image The range is from O to 20 There are two overscan modes e n Crop mode each increment adds a mask at the top bottom left and right edges of the source image equal to 0 5 of the displayed horizontal resolution 1 total A setting of 10 for example crops the image 5 on all sides or 10 total e n Zoom mode each increment adds a factor to the scaling of the source image so that the vertical and horizontal resolutions are 100 plus 1 increments of the size determined by the aspect ratio function A setting of 10 for example zooms in on the image 5 on all sides or 10 total Figure 4 6 illustrates the effect of each overs
15. Figure 2 5 shows the SC 50d SC 60d remote control and the paragraphs that follow lt DHD Controller describe its functionality SC 50d SC 60d Remote Control Unit Figure 2 5 DHD Controller SC 50d SC 60d Remote Control Signature Cinema SC 50d SC 60d Installation Operation Manual 11 Controls and Functions IR OUTPUT INDICATOR Lights when a button is pressed to indicate that an IR signal is being transmitted LIGHT Press to illuminate the buttons ON OFF Press to turn the DHD Controller and projector on or off ENTER Press to select a highlighted menu item or confirm a changed setting Cursor Buttons A 4 V gt Use these buttons to select items or settings adjust settings or switch display patterns When no menu is present on screen the UP and DOWN buttons toggle through the available aspect ratios in this order UP Button Native Virtual Cinema Cinema VirtualWide Letterbox 4 3 16 9 DOWN Button 16 9 4 3 Letterbox VirtualWide Cinema Virtual Cinema Native Not For more information about aspect ratios refer to Table 4 1 A ote Likewise the LEFT and RIGHT buttons toggle through the different source inputs in this order LEFT Button HDMI 4 HDMI 3 HDMI 2 HDMI 1 SCART HD 2 HD 1 Component Composite 3 Composite 2 Composite 1 RIGHT Button Composite 1 Composite 2 Composite 3 Component HD 1 HD 2 SCART HDMI 1 HDMI 2 HDMI 3 HDMI 4 EXIT Press this
16. Manual Installation CineWide with AutoScope maintains constant image height independent of the aspect lt Configure Lens Motor ratio while using the full display resolution of the projector It accomplishes this by moving Trigger CineWide with the anamorphic lens in front of the primary lens when widescreen material is being viewed AutoScope When the viewer transitions back to 16 9 or 4 3 source material the anamorphic lens moves out of the light path To configure the lens motor trigger on the DHD Controller for proper AutoScope operation 1 Project a 2 35 1 aspect ratio test pattern or other image on the screen On the DHD Controller remote control or front panel press MENU Select Service from the Main Menu and enter the Service Menu passcode You must enter a passcode to access the Service menu for the first A Note time after turning on the system Select Triggers from the Service menu Assign the trigger output to which the lens motor is connected to the Cinema and Virtual Cinema aspect ratios This enables the lens motor to move the anamorphic lens into position in front of the primary lens when either aspect ratio is selected 6 Select the Cinema or Virtual Cinema aspect ratio to move the anamorphic lens into position if it isn t already To do this press CINEMA or V CINE on the DHD Controller remote control Figure 2 5 or press A or W repeatedly with no menus visible on screen Refer to Figure 3 23 and pro
17. The aspect ratio selection is automatically saved for each input and resolution Signature Cinema SC 50d SC 60d Installation Operation Manual 53 Operation lt Main Menu Runco Video NAAA Aspect Ratio Picture Input Position Memory Presets Sleep Timer Information Calibration Service lt Input Source Input Source gt PERA Composite 2 Composite 3 Component HD 1 HD 2 SCART HDMI 1 HDMI 2 HDMI 3 HDMI 4 lt Aspect Ratio Aspect Ratio PASTA 4 3 Letterbox VirtualWide Cinema Virtual Cinema OOOUOOOR Native Operation Table 4 1 Aspect Ratio Settings Remote Aspect Ratio Control Description Key 16 9 16 9 Select 16 9 to view 16 9 DVDs and HDTV programs in their native aspect ratio 16 9 Image on 16 9 Screen Display 4 3 images are stretched horizontally to fit a 16 9 screen 4 3 Image stretched to fill 16 9 Screen Display 4 3 4 3 Standard 4 3 scales the input signal to fit in the center of the 16 9 screen 4 3 is the aspect ratio used by computer monitors standard television programming and most VHS video cassettes 4 3 Image on 16 9 Screen Display Letterbox LET Letterbox mode scales zooms BOX in on a 4 3 image linearly by the 43 Image n same amount on all sides to fill 16 9 Display a 16 9 display Letterbox aspect ratio Letterbox is best suited for viewing LaserDisc movies or non anamorphic DVDs on a
18. a newer firmware version than the one currently installed is available you can have the DHD Controller automatically download and install it To do this select Auto Perform Upgrade from the Auto Firmware Upgrade menu and set it to On The upgrade will occur the next time the DHD Controller is power cycled powered off then on again If you prefer to do this manually set it to Off The DHD Controller will ask if you want to perform the upgrade the next time it is power cycled e Check For New Firmware To have the DHD Controller check for new firmware on demand and perform an upgrade if it finds a new version select Check For New Firmware from the Auto Firmware Upgrade menu If the DHD Controller finds a new firmware version select Yes to perform the upgrade or No to return to the previous menu 72 Signature Cinema SC 50d SC 60d Installation Operation Manual E Mail Notification Select E Mail Notification from the Network menu to specify when and to whom the DHD Controller sends error and service notification messages via e mail The notification messages are in the following format To E Mail Address see below From do not reply runco com Subject Type of notification from Runco DHD4 Body This is an automated message sent from the Runco DHD4 Notification One of the following DHD Error Display Error Periodic Service Notification Lamp Life Notification Calibration D
19. and Adjusting the CineWide Anamorphic Lens see 45 Attach Lens Mounting Assembly to Lens Motor Carriage Plate ss 46 Configure Lens Motor Trigger CineWide with AutoScope ooooooccccccccccccicncanannnnnnos 47 Adjust the Anamorphic Lens ooocciccconiononnnnnnccnncncnonnonnnnnonnncnncnnnconnonnan nn eene 47 Verify Proper Image Alignment with Anamorphic Lens ssssssee 50 Working With the Lamp s iet eie lat dais 50 xij Signature Cinema SC 50d SC 60d Installation Operation Manual Table of Contents COME UTEM A idea 51 Using the On Screen MENUS enmarca diesels ML FWYD FF eode e ds E FFY TA 51 Main Me FETHU HT td FFR HF d te E ae HE Ee HER End 53 A Obere e Ue e EA B n E E E 53 Aspect Ratio ene t HR Mo ED CR IR Ie teu Y Y LR THIS 53 Pictur Greene Geg Y De Td Cd Giana ear avian atin nao 56 IripputiPOSItiOns ne diecast E E P Ri ra Po Oed Rede E e TEE noto e URS 60 Mermoty Presels a doti a DR ie aa UR aeg S o E HR 62 Sleep TIETIGr eu RY GY YY ars 63 MOMO sce erede D DE o i M EN E E e EL Lt A E e Lt 64 alibEatloFtz hurt ate a siamese chess AEA utet det Soter tuu RF ON iode ted 65 SeIVICe GGH Y A eU et e eire Te 70 5 Maintenance and Troubleshooting eese eee eeeeeeneen nennen 81 Lamp Replacement irte Ee et DRE o Hebe e i Ed 81 Troubleshootirig TIS stes tet ue idee mde eret te uet ERR es Fo FR CAW A 83 6 External Control iicsiisiciseceieceissca
20. button to exit the current menu and return to the previous one MENU Press this button to access the OSD controls or to exit the current menu and return to the previous one Memory Preset Buttons ISF NIGHT Press to recall settings for the current input from the ISF Night memory preset ISF DAY Press to recall settings for the current input from the ISF Day memory preset CUST 1 Press to recall settings for the current input from the Custom 1 memory preset CUST 2 Press to recall settings for the current input from the Custom 2 memory preset VID 1 1 VID 2 2 VID 3 3 Press to select a composite video input as the source or to enter the numeric character 1 2 or 3 12 Signature Cinema SC 50d SC 60d Installation Operation Manual Controls and Functions 10 HD 1 4 HD 2 5 Press to select a HD RGBHV or YPbPr component input or to enter the numeric character 4 or 5 11 COMP Component 6 Press to select the Component video input as the source or to enter the numeric character 6 12 HDMI 1 7 HDMI 2 8 HDMI 3 HDMI 4 0 Press to select an HDMI input as the source or to enter the numeric character 7 8 or O 13 SCART 9 Press to select the SCART video input as the source or to enter the numeric character O 14 Aspect Ratio Selection Buttons Use these buttons to select an aspect ratio directly as follow
21. free from defects in material and workmanship during the warranty period provided below If in Runco s sole determination a product proves to be defective in material or workmanship during the warranty period Runco will repair the product replace the product with a substantially similar new or like new product or refund a prorata share of the purchase price calculated based on the remainder of the warranty period and the then current MSRP of a similar product if repair or replacement of the product is determined by Runco to not be feasible Runco has sole discretion in determining whether a same or like model is offered and what constitutes a substantially similar model Length of Warranty Runco products are warranted for two 2 years from the date of shipment from Runco Lamps are warranted six 6 months from the date of shipment or 1000 hours of use whichever comes first All other accessories which include but are not limited to cables remotes carrying cases lens cap and other peripherals sold with the Runco product are warranted for ninety 90 days from the date of the original shipment of the accessory Eligibility This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an authorized Runco dealer or distributor This warranty is not transferable You may be required to provide proof of purchase in order to receive warranty services 1 Runco may update this
22. is adjustable for 40 6in 103 multiple lenses 1 3mm 11 3inJ i 26 9in 288 3mm 682 4mm 4 5in 114 6mm LULUQ9S Uto c UL UJuu6 gc Figure 7 2 SC 50d CineWide with AutoScope and SC 60d CineWide with AutoScope Dimensions 102 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 7 3 lists the signal types supported by each input on the DHD Controller Table 7 3 Supported Signal Timings by Input Specifications 7 5 Supported Timings Supported Y Yes No Horizontal P t yn P a Format Resolution Refresh Freguency Pixel Frequency ra TONOS 2 E 553 Rate Hz kHz MHz B zzzz S T o5 IIII 5 o EEE ooo o 000 60 00 31 469 25 175 y y y 66 59 35 892 29 862 y y y 640x480 640x480 72 00 37 861 31 500 y y y 75 00 37 500 31 500 y y y z 85 00 43 269 36 000 y y y 60 00 37 879 40 000 y y y 72 00 48 077 50 000 y y y 800x600 800x600 75 00 46 875 49 500 y y y 85 00 53 674 56 250 y Y Y 832x624 832x624 74 54 52 849 60 036 y y y 47 95 25 270 27 089 y y Y 848x480 848x480 60 00 31 020 33 750 y y y 60 00 48 363 65 000 y y y 70 00 56 476 75 000 y y y 1024x768 1024x768 75 00 60 023 78 750 y y Y 85 00 68 677 94 500 y y Y 1152x864 1152x864 75 00 67 500 108 000 y y y 1280x720 1
23. jittery and or tearing you may want to enable Film Mode to ensure stable processing for that source CUE Chroma Upsampling Error Correction Some DVD players use MPEG decoders that do not correctly upsample the 4 2 0 format chroma information on the DVD to the 4 2 2 or 4 4 4 format required by the video encoder of the display device This so called chroma bug sometimes causes streaky or spiky horizontal lines running through the chroma channel It is most noticeable in static interlaced scenes and on diagonal edges especially red ones Set CUE to On to correct this issue e Remote Code Select Remote Code from the Miscellaneous menu to set the infrared IR code set to which the DHD Controller will respond By default it is set to 17 You can change this setting if either e Another device in the theater a DVD player for example is responding to commands from the DHD Controller remote control Figure 2 5 in ways that are unpredictable or undesirable e You have multiple DHD Controllers and want to control them independently as opposed to broadcasting commands from a single remote to all of them In this scenario you can use multiple remotes programmed to use different IR codes Or you can use a single remote and change the IR code as needed to address a specific DHD Controller Use the DHD Controller front panel keypad to change the IR code to A Tip which the controller will respond Then
24. of the splash screen that appears on the display upon power up e Owner Name ISF Calibrated ISF Other You can have the SC 50d SC 60d display the owner s name your name the phrase ISF Calibrated and or any other string up to 30 characters in length Use the up or down cursor button to select a character Use the right and left cursor buttons to change the cursor position Press MENU when you have finished entering text e Splash Timer When you turn on the SC 50d SC 60d it projects a welcome screen with the Runco and ISF logos along with the personalized information you enter as described above Select Splash Timer from the Splash Configure menu to set the amount of time for which this screen appears The range is from 5 to 60 seconds in one second increments Press lt or to set the timer then press MENU e Splash Enable When you have finished customizing the splash screen select Splash Enable from the Splash Configure menu Then select On and press ENTER OSD Position To adjust the position of the OSD select OSD Position from the Calibration menu and press ENTER Press A or W to select Hor or Ver Then press or p to change the position Signature Cinema SC 50d SC 60d Installation Operation Manual 69 Operation Service y Service SS Input Names Display Device Network Color Space Triggers Miscellaneous Sync Threshold HDMI Front Panel Brightness S
25. press ENTER On your external test pattern source select a pattern like the one shown in Figure 4 5 Adjust as needed looking for white edges around the transitions from black to gray and differently sized lines in the sweep patterns at the top and bottom Lower the sharpness setting to eliminate them Figure 4 5 Typical Test Pattern for Adjusting Sharpness Noise Filter To apply noise filtering to the input signal select Noise Filter from the Picture menu The Noise Filter is useful for clearing up noisy images from 480i video sources Use the left or right arrow buttons to select the desired amount of noise reduction keeping in mind that higher settings which reduce high frequencies may also soften the image Use the controls in the Input Position Menu to fine tune the aspect ratio and image position for the current source The input position settings are automatically saved for each input A Note and resolution Left Right Select Left Right from the Input Position menu to shift the projected image horizontally Press p gt to shift the image to the right press lt q to shift it to the left Up Down Select Up Down from the Input Position menu to shift the projected image vertically Press p to shift the image upward press to shift it downward Width Select Width from the Input Position menu to change the projected image width Press to increase the width press to decrease it 60 Signature
26. the projector Secure the motor to the projector with the eight screws provided for this purpose See Figure 3 7 Then connect the 12V trigger input on the motor to a 12V trigger output on the DHD Controller as shown in Figure 3 18 em Figure 3 7 Attaching the AutoScope Lens Motor to the Projector DO NOT OVER TIGHTEN THE SCREWS Caution 26 Signature Cinema SC 50d SC 60d Installation Operation Manual There are several methods for mounting the projector Depending on your chosen installation one method may be more suitable than another In typical front and rear screen installations the projector can be mounted to a secure and level surface such as a table or cart Carts are useful when moving a projector during a presentation or from site to site If possible lock the wheels when it s in position to prevent it from being moved during a presentation For fixed installations and for those that want the projector out of sight or have a limited space for projector and audience you can invert the SC 50d SC 60d and suspend it from the ceiling using a specially designed ceiling mount fixture Use only the Runco approved ceiling mount kit designed for your A Note projector Install the ceiling mount kit according to the instructions provided with the kit The projector can also be inverted and placed in an enclosure above and behind the viewing area Install four feet on the inside bottom surface of the enclosure on which t
27. to DHD Controller sessist yiee kienta e 36 3 17 RS 232 Control System Connection to DHD Controller eeeeeese 37 3 18 Connecting 12zvolt Trigger AIRE acti rar ted 38 3 19 External IR Receiver CONNECtiON ooccoccconcccncnnccncconnnonannonccnnnnnncnncnonnnnnnncnnncnnncnncnnnnnns 39 3 20 Ethernet Network Connection to DHD Controller ss 40 3 21 Keystone and Pincushion Distortion ssssssssseee e 43 3 22 Image Alignment Controls 53 rie mer th te ED OA C t p PORA E P 44 3 23 Anamorphic Lens Mounting Assembly Exploded View ssssseee 45 3 24 Attaching the Anamorphic Lens to the Lens Ring ssesee RE LL RYAN 46 4 1 SC 50d SC 60d OSD Menu Structure sssssssssssseeeeeeeeeenen enne 51 4 2 Typical PLUGE Pattern for Adjusting Brightness ss Y LL RF A LL RYAN 56 4 3 Typical Gray Bar Pattern for Adjusting Contrast sss 57 4 4 Typical Color Bar Pattern for Adjusting Color Saturation and Tint sssse 58 Signature Cinema SC 50d SC 60d Installation Operation Manual XV List of Figures 4 5 Typical Test Pattern for Adjusting SharpnesS occiccicnconconnononcnnccnncononnninnonnnnnncnnccnncnnns 60 4 6 Overscan MOGES 3 hid te reo HR Pe o E HD RR bed Pet e he SR HO pc FD Yd 61 4 7 CIE 1931 Chromaticity Digranes teurer etiri mmm 67 521 Opening the Lamp Dodo reete ies lent tet eee a ege
28. transmit HDMI CEC control A Note messages from the HDMI Audio Out connector For more information about CEC refer to Using HDMI CEC Messages on page 94 Audio Processor Switcher Figure 3 16 Audio Processor Connection to DHD Controller 36 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation The DHD Controller provides the following interfaces to external equipment that allow t to lt lt Additional Connections to control or be controlled by that equipment the DHD Controller e An RS 232 interface to a PC or control automation system Optional e Three 3 12 volt trigger outputs e An infrared IR repeater input e An Ethernet network interface for firmware updates and maintenance notifications The following sections describe how to make these interface connections For more information about using these connections refer to Network on page 71 and External Control on page 85 RS 232 Controller Connection Use a straight through 9 pin RS 232 cable to connect a PC or control automation system if present to the RS 232 port on the DHD Controller see Figure 3 17 RS 232 Display Control HDMI Out HDMI 3 To Display to Automation 2 Receive Data Control System 3 Transmit Data or PC amp 4 5 Ground
29. with an anamorphic lens To correct keystoning or pincushion distortion 1 On the DHD Controller remote control or front panel press MENU 2 Select Calibration from the Main Menu and enter the Calibration Menu passcode You must enter a passcode to access the Calibration menu A Note Select Image Alignment from the Calibration Menu Select Corner Alignment to correct a keystoned image by adjusting the image corner positions Select Midpoint Alignment to correct pincushion distortion by adjusting the image edge mid points See Figure 3 22 Use the built in test pattern when adjusting the image corners or A Tip midpoints To access it check the Test Pattern box in the Corner Alignment or Midpoint Alignment menu Top Left x y Top Middle x y Top Right x y o e Left ANZ cia ur EM AL E M pP NM CG CAME YI AR A RC Da O OUR Right Middle pes e O Middle x y 9 e e e Bottom Left x y Bottom Middle y Bottom Right x y Notes 1 Bottom Middle x Top Middle x 2 Right Middle y Left Middle y 3 Smaller x values move a point to the left larger values move it to the right 4 Smaller y values move a point up larger values move it down Figure 3 22 Image Alignment Controls y coordinate Similarly the Top Middle x setting also controls the The Left Middle y setting also controls the Right Middle A Note Bottom Middle x coordinate 44 Signature
30. with the ferrite sleeve to A WARNING connect the projector to AC power Doing otherwise creates a fire hazard risk Connect the DHD Controller to a nearby AC outlet using the other AC power cord AutoScope Lens Motor With AutoScope equipped projectors an additional power cord is provided for the lens motor Plug the female end of the AC power cord into the AC input on the rear of the lens motor assembly Connect the other end to your AC power source 40 Signature Cinema SC 50d SC 60d Installation Operation Manual 1 Power up your source components Turn on the main power switch at the rear of the projector 3 If this is an AutoScope equipped projector turn on the main power switch at the rear of the AutoScope lens motor The lens motor power switch is located next to the AC input See Figure 3 18 4 Turn on the main power switch at the rear of the DHD Controller Press the ON button on the remote control or the ON STANDBY button on the DHD Controller front panel to turn on the system The vacuum fluorescent display on the DHD Controller front panel briefly displays Initializing System followed by Starting SC 50d SC 60d 6 When the display is ready for use the fluorescent display indicates the active source input resolution frame rate and aspect ratio for example Current Source SC 50d SC 60d HDMI 1 16 9 1080p 60 Aspect Ratio Input Resolution Frame Rate Lens zoom focus and positi
31. you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen Estimating Throw Distance Throw Distance TD Screen Width w x Lens Throw Ratio 10 Figure 3 1 Estimating Throw Distance Table 3 3 lists the available SC 50d SC 60d lens options and their throw ratios Table 3 3 SC 50d SC 60d Lens Options and Throw Ratios Note Throw Range in Throw Ratio Throw Range in Throw Ratio inches with with Primary inches with Lens Option with Primary 120x67 5 inch 1 78 1 Lens and 158 6x67 5 inch Lens Only Screen Anamorphic 2 35 1 Screen Minimum Maximum Lens Minimum Maximum For rear screen installa tions only Contact Athena Uno cannot be used with an Runco Technical Support anamorphic lens for more information Athena Uno 0 67 Fixed Athena Dos 1 39 1 85 166 80 222 00 1 20 1 39 190 36 220 50 Athena Tres 1 85 2 59 222 00 310 80 1 39 1 94 220 50 307 74 Athena 2 59 4 16 310 80 499 20 1 94 3 12 307 74 494 93 Quatro _ 416 693 49920 831 60 3 12 5 20 494 93 824 88 Note Due to normal manufacturing variances throw distance can vary by up to 5 percent from these specifications 18 Signature Cinema SC 50d SC 60d Installation Operation Manual Proper placement of the projector relative to the screen will yield a rectangular perfectly centered i
32. 16 9 screen VirtualWide V WIDE VirtualWide scales a 4 3 image NON linearly more on the sides 4 3 Image on than in the center to fit a 16 9 16 9 Screen Display screen 4 3 Image on 16 9 Screen with VirtualWide On a 2 35 1 screen the image is 4 3 Image on 2 35 1 Screen centered between black bars on with VirtualWide either side 54 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 4 1 Aspect Ratio Settings continued Aspect Ratio Cinema Remote Control Key CINEMA 2 35 1 Image on 16 9 Screen Cinema aspect ratio no CineWide 2 35 1 Image on 2 35 1 Screen Cinema aspect ratio CineWide Description Select Cinema to view 2 35 source material in its native aspect ratio With a 16 9 screen and a standard SC 50d SC 60d without an anamorphic lens the upper and lower portions of the screen are masked but the geometry of the active image area is unchanged With a 2 35 1 screen and an anamorphic lens the DHD Controller scales the 2 35 1 image so that the active image area fills the 16 9 chip surface eliminating the black bars The secondary anamorphic lens then restores the proper geometry to the 2 35 1 image 1080i HDTV Image 720p HDTV Image Virtual Cinema V CINE A 16 9 image is scaled NON linearly more on the sides 16 9 Image on than in the center to fit a 2 35 1 2 35 1 Screen
33. 2 Video 3 Standard composite video inputs for connecting a VCR camcorder or other composite video source The Video 1 input also provides composite sync input for SCART RGBS sources HDMI 1 HDMI 2 HDMI 3 HDMI 4 Digital HDCP compliant digital video inputs for connecting an HDMI or DVI source Ethernet A female RJ 45 connector for wired network communications HDMI Out Audio Only Connect this output to an audio control system to pass through HDMI audio The DHD Controller does not transmit HDMI CEC control A Note messages from the HDMI Audio Out connector HDMI Out To Display Connect this to the DHD Input on the SC 50d SC 60d see Figure 2 2 RS 232 PC Control A female 9 pin D sub connector for interfacing with a PC or automation control system 10 Signature Cinema SC 50d SC 60d Installation Operation Manual Controls and Functions The SC 50d SC 60d ships with two remote control units 2 5 e A standard Runco DHD Controller remote control unit and SC 50d SC 60d A setup remote control unit for making lens adjustments Remote Control Units Only the setup remote control can be used to perform lens shift zoom and focus adjustments For this reason you must use it to complete the initial SC 50d SC 60d installation and setup After you have completed the installation only the standard DHD Controller remote control is needed to access all projector and controller functions
34. 280x720 47 95 37 833 64 769 y y y 60 00 47 396 68 250 y y y 60 00 47 776 79 500 Y y y 1280x768 1280x768 75 00 60 289 102 250 y Y Y a 85 00 68 633 117 500 y y y 60 00 60 000 108 000 y y y z 1280x960 1280x960 85 00 85 938 148 500 y y Y Signature Cinema SC 50d SC 60d Installation Operation Manual 103 Specifications Table 7 3 Supported Signal Timings by Input continued Supported V Yes No rN CO Format Resolution a i E si jo 4o OQ 2 fr 3 kHz 22 64400 E 5 eee II 5 e 5585 o ooo 60 00 63 981 108 000 y y y 1280x1024 1280x1024 75 00 79 976 135 000 y y y 85 00 91 146 157 500 y y y 1960x768 1360x768 60 00 47 712 85 500 y y y 60 00 64 744 101 000 y y y 1400x1050 1400x1050 60 00 65 317 121 750 y y y 75 00 82 278 156 000 y y y 1600x1200 1600x1200 60 00 75 000 162 000 y y y 1680x1050 1680x1050 60 00 64 674 119 000 y y y 1920x1080 1920x1080 47 95 56 821 150 007 y y y 1920x1200 1920x1200 60 00 74 038 154 000 y y y ee M MM J poet 50 00 y 480 60i 720x487 59 94 15 734 13 500 y y y 480 60p 720x483 59 94 31 469 27 000 y y y 576 50i 720x576 50 00 15 625 14 750 y y y 576 50p 720x576 50 00 31 250 29 000 y y y 720 24p 1280x720 23 98 24 00 17 982 1
35. 4 HDMI with CEC and Deep Color 1 Component SCART 3 x RCA 2 Component RGBHV 5 x BNC 3 Composite 1 HDMI with Deep Color to SC 50d SC 60d 1 HDMI with Deep Color to second display or audio processor Front panel vacuum fluorescent display and keypad Discrete infrared IR remote RS 232 female DB9 for serial commands USB type B female for firmware upgrade RS 232 male DB9 for accessories 3 5 mm wired IR input for Niles Xantech compatible IR Systems e Consumer Electronics Control CEC protocol support via HDMI e Ethernet RJ45 female for web server e mail auto firmware upgrade and Telnet 19200 bps no parity 8 data bits 1 stop bit no flow control 3 12 VDC each rated at 250 mA and thermal fuse protected Runco Firmware Upgrader Runco BRiC backup restore clone CalMAN by SpectraCal for automatic calibration 100 240V 47 63Hz 0 45 Amps 41 F to 104 F 5 C to 40 C 0 to 90 humidity non condensing up to 10 000 feet 8 048 meters altitude Width 17 50 inches 444 5 mm Depth 11 19 inches 284 1 mm Height 3 75 inches 95 3 mm 15 4 lbs 7 00 kg Signature Cinema SC 50d SC 60d Installation Operation Manual 99 Specifications Table 7 2 DHD Controller Specifications continued Regulatory Approvals cTUVus FCC class B CE RoHS China RoHS WEEE C Tick CCC local conformances as required Limited Warranty Two 2 years parts and labor from the date of shipment f
36. 56 000 y y y 1600x1200 1600x1200 60 00 75 000 162 000 y y y 1680x1050 1680x1050 60 00 64 674 119 000 y y y 1920x1080 1920x1080 47 95 56 821 150 007 y y y 1920x1200 1920x1200 60 00 74 038 154 000 y y y A 480 60i 720x487 59 94 15 734 13 500 y y y 480 60p 720x483 59 94 31 469 27 000 y y y 576 50i 720x576 50 00 15 625 14 750 y y y 576 50p 720x576 50 00 31 250 29 000 y y y 720 24p 1280x720 23 98 24 00 17 982 18 000 59 341 59 400 y y y 720 25p 1280x720 25 00 18 750 74 250 y y y 720 30p 1280x720 29 97 30 00 22 478 22 500 74 175 74 250 y y y 720 50p 1280x720 50 00 37 500 75 250 y y y 720 60p 1280x720 60 00 45 000 74 250 y y y 1080 50i 1920x1080 50 00 28 125 31 250 74 250 72 000 y y y 1080 60i 1920x1080 59 94 60 00 33 716 33 750 74 175 74 250 y y y 1080 24p 1920x1080 23 98 24 00 26 978 27 000 74 175 74 250 y y y 1080 50p 1920x1080 50 00 56 250 148 500 y y y 1080 60p 1920x1080 59 94 60 00 67 433 67 500 148 350 148 500 y y y NTSC 3 58 59 94 60 00 15 734 15 750 3 580 y NTSC 4 43 59 94 60 00 15 734 15 750 4 430 y PAL B G H 50 00 15 625 4 430 y Signature Cinema SC 50d SC 60d Installation Operation Manual 105 Specifications Table 7 3 Supported Signal Timings by Input continued Supported V Yes No Horizontal E 5 N a Format Resolution Refresh Frequency PixelFre
37. 60d to the DHD Controller Signature Cinema SC 50d SC 60d Installation Operation Manual 29 Installation 3 7 Connections to the SC 50d SC 60d and DHD Controller lt Connecting the DHD Controller to the SC 50d SC 60d Installation RS 232 Connection Connect the Display Control output from the DHD Controller to the RS 232 input on the SC 50d SC 60d Use a standard modular telephone cable with RJ11 plugs at both ends On the SC 50d SC 60d end use the provided RJ11 to DB9 adapter This adapter is wired as shown in Figure 3 10 RCV DATA El 2 2 To From 3 A UU 3 DHD l To From Projector Controller SIG GND 1 6 NO CONNECTION 6 position RJ11 Male _ 8 mI lox Figure 3 10 RS 232 Connection from the DHD Controller to the SC 50d SC 60d 30 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation Connect your video sources to the DHD Controller as shown and described in the lt Connecting Source sections that follow Components to the DHD Controller HDMI Source Connections See Figure 3 11 video quality because the signal is carried in the digital domain throughout the entire signal path from source component output into the projector Use the HDMI inputs whenever possible This ensures the highest N Tip You can
38. 8 000 59 341 59 400 y y y 720 25p 1280x720 25 00 18 750 74 250 y y y 720 30p 1280x720 29 97 30 00 22 478 22 500 74 175 74 250 y y y 720 50p 1280x720 50 00 37 500 75 250 y y y 720 60p 1280x720 60 00 45 000 74 250 y y y 1080 50i 1920x1080 50 00 28 125 31 250 74 250 72 000 y y y 1080 60i 1920x1080 59 94 60 00 33 716 33 750 74 175 74 250 y y y 1080 24p 1920x1080 23 98 24 00 26 978 27 000 74 175 74 250 y y y 1080 50p 1920x1080 50 00 56 250 148 500 y y y 1080 60p 1920x1080 59 94 60 00 67 433 67 500 148 350 148 500 y y y NTSC 3 58 59 94 60 00 15 734 15 750 3 580 y NTSC 4 43 59 94 60 00 15 734 15 750 4 430 y PAL B G H 50 00 15 625 4 430 y 104 Signature Cinema SC 50d SC 60d Installation Operation Manual Specifications Table 7 3 Supported Signal Timings by Input continued Supported V Yes No rN CO Format Resolution a i E si jo 4o OQ 2 fr 3 kHz 22 64400 E 5 eee II 5 e 5585 o ooo 60 00 63 981 108 000 y y y 1280x1024 1280x1024 75 00 79 976 135 000 y y y 85 00 91 146 157 500 y y y 1960x768 1360x768 60 00 47 712 85 500 y y y 60 00 64 744 101 000 y y y 1400x1050 1400x1050 60 00 65 317 121 750 y y y 75 00 82 278 1
39. Carrier 27 8 us tp St First Packet Repeated Packet RC5 Packet Transmission 14 cycles 24 9 ms 64 cycles 113 8 ms Figure 6 1 RC5 Message Format Signature Cinema SC 50d SC 60d Installation Operation Manual 91 External Control IR Command List Table 6 2 lists the RC5 control codes for the DHD Controller Table 6 2 RC5 Control Codes for the DHD Controller ROS Pata RC5 Data Remote Control Remote with Toggle Description Button Name Control No is Note 16 9 0x3449 0x3C49 16 9 aspect ratio 4 3 0x344A 0x3C4A 4 3 aspect ratio CINEMA Ox346C Ox3C6C Cinema aspect ratio COMP 0x344E 0x3C4E Component video input CUST 1 0x3472 0x3C72 Custom 1 memory preset CUST 2 0x3473 0x3C73 Custom 2 memory preset DOWN 0x3446 0x3C46 Down Arrow W ENTER 0x3444 Ox3C44 ENTER EXIT Ox3474 0x3C74 EXIT HD 1 0x3451 Ox3C51 HD1 video input HD 2 0x3452 Ox3C52 HD2 video input HDMI 1 Ox3453 Ox3C53 HDMI1 video input HDMI 2 0x3454 Ox3C54 HDMI2 video input HDMI 3 0x3455 0x3C56 HDMI3 video input HDMI 4 0x3456 Ox3C56 HDMIA video input ISF DAY 0x3471 0x3C71 SF Day memory preset ISFNT 0x3470 0x3C70 SF Night memory preset LEFT 0x3447 0x3C47 Left Arrow lt q LET BOX 0x344B 0x3C4B Letterbox aspect ratio MENU 0x3443 Ox3C43 MENU NATIVE Ox346E Ox3C6E Native aspect ratio OFF 0x3442 0x3C42 Power off ON 0x3441 0x3C41 Power on RIGHT 0x3448 0x3C48
40. DHD Controller and the SC 50d SC 60d e HDMI EDID Extension Extended display identification data EDID is a data structure provided by a display device to describe its capabilities to a graphics card It is what enables a modern personal computer to know what kind of monitor is connected Some modern display devices provide more information via EDID than others in the form of extensions Some computer graphics cards do recognize or properly interpret this extended EDID information Select HDMI EDID Extension from the HDMI menu to specify whether or not the EDID extensions from the display device are passed through to the 3Dimension Processor and to the sources connected to the HDMI 1 HDMI 2 HDMI 3 or HDMI 4 inputs By default the extensions are on Change these settings only if HDMI EDID incompatibility issues arise Audio Format Select Audio Format from the HDMI menu to choose an option for routing the audio signal from an HDMI source With the SC 50d SC 60d the recommended setting is HDMI Out Audio Only This is also the default setting e CEC This control chooses whether or not the DHD Controller responds to HDMI CEC control messages from a disc player set top box or other HDMI source The default setting is On For more information about CEC refer to Using HDMI CEC Messages on page 94 The DHD Controller does not transmit HDMI CEC control A Note messages from the HDMI Audio Out connector regardless of th
41. HD Controller SC 50d SC 60d Remote Control ssssseeeeee 11 2 6 Setup Remote Control for SC 50d SC 60d ccccccccnconocononnnonononeneninnonononononnnnnanononininnnons 14 3 1 Estimating Throw DISteree eto id uwy et tete cerei teet e cb Ped Pu d YO eae DR 18 3 2 Projector Placeniention on eco e esa ede tele Ra TI eoa ae 19 3 3 Vertical Lens Shift EXAMPLE ONLY eee enne DN DD RR DD nennen 19 3 4 Horizontal Lens Shift EXAMPLE ONLY ssssssse memes 20 3 5 Folded OptlGSiua rete E n m e oM DE e o Der Re ERR 22 3 6 Ventilation Requirements for Enclosure Mounting sse LH FFF LL RYAN 24 3 7 Attaching the AutoScope Lens Motor to the Projector ssssssssse 26 3 8 Mounting Angle Ranges Front to Back and Side to Sid6 99 99 eeeeeeeee eiu 28 3 9 Connecting the SC 50d SC 60d to the DHD Controller eee 29 3 10 RS 232 Connection from the DHD Controller to the SC 50d SC 60d 30 3 11 HDMI Source Connections essen eene Ea Yai Virb iait 31 3 12 Component Video Source Connections essen 32 3 13 RGBHV Source GConnectloris erred e rte rete e e ee Seb ede era 33 3 14 SCART RGBS Source CONNECtIONS ooooococccccccncccccninnnonnnncnnncnncnncconononnnnoncnnccnncnnccnnnns 34 3 15 Composite Video Source Connections cooocccnnononenininincononononononnnnnnnononnnonononeneneninnos 35 3 16 Audio Processor Connection
42. INSTALLATION OPERATION MANUAL SIGNATURE CINEMA SC 50d Series SC 60d Series Full HD Private Cinema Projector and Digital High Definition DHD Controller Processor RUNCO RuncoCare Standard Two Year Limited Warranty Congratulations on your purchase of a Runco product With proper installation setup and care you should enjoy many years of unparalleled video performance This RuncoCare Standard Limited Warranty is provided free of charge by Runco International LLC Runco with the purchase of a covered Runco product The following sets forth Runco s Standard Limited Warranty applicable to all Runco projectors processors LCD display and plasma display products with the exception of the following models XP 103DHD SC 1 SC 1a CW 95DHD and VW 100HD The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us Runco and you the customer who has purchased a Runco product This contract applies to purchases of covered Runco products occurring on or after February 11 2010 Runco reserves the right to change the terms of this contract and such changes shall apply to purchases of covered Runco products that occur on or after any future effective date RuncoCare Standard Features e Two year protection from defects in material and workmanship e Access to 24x7 phone support e Complimentary second day one way shipping Warranty Coverage Runco warrants its products to be
43. PNESS 50 50 YES Sets a value for sharpness SHARPNESS NA NA Returns sharpness setting value TINT 50 50 YES Sets a value for tint TINT NA NA Returns tint setting value Signature Cinema SC 50d SC 60d Installation Operation Manual 87 External Control External Control Table 6 1 Serial Commands continued Command Parameter Value Description min max Stored P Image Preset Commands CUSTOM NA YES Loads Custom 1 image preset CUSTOM2 NA YES Loads Custom 2 image preset DAY NA YES Loads ISF Day image preset NIGHT NA YES Loads ISF Night image preset PRESET NA NA Returns currently selected preset ISF Day ISF Night Custom 1 or Cus tom 2 Input Position Commands IEIGHT 0 20 YES Sets the value for input height IEIGHT NA NA Returns input height value HPOS 50 50 YES Sets a value for horizontal input position HPOS NA NA Returns input horizontal position value VPOS 50 50 YES Sets a value for vertical input position VPOS NA NA Returns input vertical position value WIDTH 0 50 YES Sets the value for input width WIDTH NA NA Returns input horizontal width value OVERSCAN 0 20 YE Sets the overscan percentage OVERSCAN NA NA Returns overscan percentage OVERSCANMODE 0 1 YES Sets the overscan mode 02zoom 1 crop OVERSCANMODE NA NA Returns the overscan mode 0 zoom 1 crop Output Shift Commands
44. Right Arrow p gt SCART 0x3457 Ox3C57 SCART video input STOFF 0x3460 0x3C60 Sets the sleep timer to Off ST3OMIN 0x3461 0x3C61 Sets the sleep timer to 30 minutes Note These codes assume that the default address of 17 is used If you change it to something other than 17 you will need to modify these codes accordingly 92 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 6 2 RC5 Control Codes for the DHD Controller continued a RC5 Data Remote Control with Toggle E Remote Description Button Name Bit 1 Control Note Note ST60MIN 0x3462 0x3C62 Sets the sleep timer to 60 minutes ST90MIN Ox3463 Ox3C63 Sets the sleep timer to 90 minutes ST2HRS Ox3464 Ox3C64 Sets the sleep timer to 2 hours STAHRS 0x3465 0x3C65 Sets the sleep timer to 4 hours UP 0x3445 0x3C45 Up Arrow A VID 1 0x344D 0x3C4D Composite video input 1 VID 2 0x3458 0x3C58 Composite video input 2 VID 3 0x3459 0x3C59 Composite video input 3 V CINE 0x346D Ox3C6D Virtual Cinema aspect ratio V WIDE Ox344C Ox3CAC VirtualWide aspect ratio Note These codes assume that the default address of 17 is used If you change it to something other than 17 you will need to modify these codes accordingly Signature Cinema SC 50d SC 60d Installation Operation Manual 93 External Control External Control 6 3 The DHD Controller accepts and can respond to CEC command messages from a disc Using HDMI CEC pl
45. Texas Instruments Digital Light Processing DLP dual imaging system SuperOnyx DMD Full HD 1920 x 1080 1080p SC 50d 2 000 hours typical SC 60d 1 300 hours typical 4 3 Letterbox 16 9 VirtualWide Cinema Virtual Cinema Native Refer to Table 7 2 Recommended Width 100 132 in Maximum Width 264 in Recommended Width 120 198 in Maximum Width 420 in Runco DHD4 Processor with ViVix IV technology and BRiC Backup Recovery and Clone tool e Serial commands via RS 232 e Discrete infrared IR remote e Consumer Electronics Control CEC protocol support via HDMI e Ethernet Refer to Table 7 2 NTSC PAL SECAM CEA 861D ISF Certified Calibration Configuration Refer to Table 3 3 Refer to Table 3 4 SC 50d CSMS Specifications Private Cinema Calibration 3 471 ANSI Lumens 126 Foot Lamberts fL Uncalibrated 6 000 ANSI Lumens SC 60d CSMS Specifications Private Cinema Calibration 5 785 ANSI Lumens 210 Foot Lamberts fL Uncalibrated 10 000 ANSI Lumens Measured on a 1 0 gain 84 wide 16 9 screen CSMS Contrast Ratio gt 500 1 ANSI Signature Cinema SC 50d SC 60d Installation Operation Manual 97 7 1 SC 50d SC 60d Projector Specifications Specifications Table 7 1 SC 50d SC 60d Projector Specifications continued lllumination System Power Requirements Power Consumption Operating Temperature Operating Humidity Dimensions Weight wit
46. The white areas are a comfortable level of true white e The image contains only black gray and white no color Contrast On your external test pattern source select a stepped gray bar pattern like the one shown in Figure 4 3 Figure 4 3 Typical Gray Bar Pattern for Adjusting Contrast Select Contrast and press ENTER Adjust the contrast to a point just below which the white rectangle starts to increase in size Brightness and contrast controls are interactive A change to one A Note may require a subtle change to the other in order to achieve the optimum setting Signature Cinema SC 50d SC 60d Installation Operation Manual 57 Operation Color Saturation On your external test pattern source select a color bar pattern like the one shown in Figure 4 4 lt Tall color bars Short color bars E Tint Color Figure 4 4 Typical Color Bar Pattern for Adjusting Color Saturation and Tint Oo O fF WB nm 8 9 Press the MENU button on the remote control or DHD Controller front panel Select Service from the Main Menu and press ENTER Enter the Service menu passcode Select Display Device from the Service menu and press ENTER Press ENTER again to select Configure Select Diagnostics and press ENTER Select Blue from the Diagnostics menu then press ENTER to display only the blue color channel Press EXIT or MENU repeatedly to return to the Main Menu Select Picture fr
47. al nue Sel al 2 Description Features and Benefits ooooonnnnnnnnnniononccnncnnnnnncnonananan ono emen 3 Key Features andBenefitS lea o at PL RR REA y Rc 4 p mH I 4 2 Controls and Functions eeeeseeeeeeeeeeeeee seen en nnns ennt nhan nnns assa anna sans nnns 5 SC 50d SC 60d at a GIafICe xoi o oce esi ete Ee be ee etia d 5 o0 50d SG b0d Input Panel eau ot eb e Pao t be HO aay 6 DAD Controller Front Patel ee eed e re esr A 8 DAD Gontroller Rear Pariels a cio cte e ttn Y nahe anten 9 SC 50d SC 60d Remote Control Units esee 11 DHD Controller SC 50d SC 60d Remote Control Unit eres 11 Setup Remote Conto itid tdt re dO eee tede rb 14 3 instalation ME 15 Remote Control idiv ia ta ete Aetna ied ete e e eb EA 15 Notes on Batteries ioa ede e ED e ERU d ER Pe ER TEE RM 15 Notes on Remote Control Operation ssssssss eee 16 QUICK SGtUp s c ice ta eres een px a Ee EX a TERR EX TED RU E PRI EE FFAN RR ERR Ra a 16 Signature Cinema SC 50d SC 60d Installation Operation Manual Xi Table of Contents Installation Consideran iesin shed em des odes vided ias 17 Installation Type ciis lea Ge aie ee el col eae 17 Ambient Light i iei t t ra een a bep d P b e tate 17 dato DISTANCE er ET 18 Vertical a d Horizontal POSO epps piri Pe coa em b eds 19 Vertical and Horizontal Lens Shift mee 19 Folded Optic Siy itni ea ep e Ty ed eo e e MER e Hoo t pene 22 Audio Video Synchroniza
48. also connect computers with DVI output to these inputs A Note Refer to Supported Timings on page 103 for a list of compatible input signals HDMI HDMI AV OUT O AV OUT EE ooo O 1 iJ IU ii ooo UY HDMI sources BD DVD DTV Set Top Box etc Figure 3 11 HDMI Source Connections Signature Cinema SC 50d SC 60d Installation Operation Manual 31 Installation Component Video Source Connections Connect your component video sources to the HD1 HD2 and or Component SCART inputs as shown in Figure 3 12 TRIGGERS RCA to BNC c nod adapter muumummumuumummumuumummuo COMPONENT vpEoour O Y DTV Set Top Box BD DVD DTV STB Figure 3 12 Component Video Source Connections 32 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation RGBHV Source Connections Connect personal computers and or other RGB sources to the HD1 and or HD2 inputs as shown in Figure 3 13
49. ata Detailed Description If a DHD Error one of the following Fan Failure 1 Fan Failure 2 Overtemp 1 Overtemp 2 Initialization Failure If a Display Error a device specific error message such as Lamp Door Open If a Periodic Service Notification the elapsed time since the last notification If a Lamp Life Notification the number of hours the lamp has been in servic If a Calibration Data message See Attached File Serial Number DHD Controller serial number Customer Information From Customer Information sub menu see below Best Regards Runco International LLC 1195 NW Compton Drive Beaverton OR 97006 1 800 237 8262 e E Mail Address To specify the destination e mail address for error and service notifications select E Mail Address from the E Mail Notification menu The procedure is similar to that for setting the IP address refer to IP Configuration on page 71 Enter up to 45 alphanumeric characters Error Notification To have the DHD Controller send a message to the destination e mail address when a DHD Error or Display Error occurs select Error Notification from the E Mail Notification menu and set it to On Error Notification to Runco To have the DHD Controller send an e mail message to Runco Customer Support when a DHD Error or Display Error occurs select Error Notification to Runco from the E Mail Notification
50. ation Operation Manual 85 6 1 Serial Communications lt RS 232 Connection and Port Configuration lt Serial Command Syntax External Control Table 6 1 lists the RS 232 command set The Parameter min max column shows the valid parameter ranges or NA for commands that take no parameters When you enter a valid command the DHD Controller executes it and acknowledges it with a plus sign on the command line gt When you enter an invalid command one that is misspelled or followed by values outside the valid range for that command the DHD Controller ignores it and returns a minus sign gt Table 6 1 Serial Commands Command Parameter Vae Description min max Stored Power On Off Commands OFF NA NA Turns projector off ON NA NA Turns projector on POWER 0 1 NA Turns projector on and off POWER NA NA Returns power status Input Selection Commands COMPONENT NA YES Selects the Component input COMPOSITE NA YE Selects the Composite 1 video input COMPOSITE COMPOSITE2 NA YE Selects the Composite 2 video input COMPOSITES NA YE Selects the Composite 3 video input HDMI1 NA YES Selects the HDMI 1 input HDMI2 NA YES Selects the HDMI 2 input HDMIS3 NA YES Selects the HDMI 3 input HDMI4 NA YES Selects the HDMI 4 input HD1 NA YES Selects the RGB HD 1 input HD2 NA YES Selects the RGB HD 2 input NPUT NA NA Returns ac
51. aumummumummumummm Computer RGB Camcorder Figure 3 13 RGBHV Source Connections Signature Cinema SC 50d SC 60d Installation Operation Manual 33 Installation SCART RGBS Source Connections Connect the green blue and red outputs from your SCART source to the Component SCART input on the DHD Controller Connect the sync output from your SCART source to the Video 1 input on the DHD Controller See Figure 3 14 VCR j O scaRT4o RGBS zm adapter DVD DTV STB Gaming Console Figure 3 14 SCART RGBS Source Connections 34 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation Composite Source Connections See Figure 3 15 Composite Composite Composite Composite Camcorder Gaming Console gt Composite Composite Figure 3 15 Composite Video Source Connections Signature Cinema SC 50d SC 60d Installation Operation Manual 35 Installation Connecting an Audio x Processor or Secondary Display Device to the DHD Controller Optional The DHD Controller provides a second HDMI output labeled HDMI Out Audio Only for connection to an audio receiver switching system or secondary display device for monitoring purposes See Figure 3 16 The DHD Controller does not
52. ayer satellite receiver or DVR set top box via an HDMI connection Using CEC the DHD Messages Controller can perform the following actions e Turn itself and the display device on and select the correct input when the source component initiates playback of a disc or recorded program e Turn the source component on when you switch to its corresponding input on the DHD Controller e Turn the source component off when the DHD Controller is turned off unless the source component is in playback mode Change its OSD language when a similar change is made at the source To use CEC connect your CEC compatible sources to the HDMI inputs on the SC 50d SC 60d Set the CEC option to On refer to CEC on page 78 Additional steps may be needed to enable CEC at the source Refer to the documentation for your source device for more information CEC Command List Table 6 3 lists the CEC commands supported by the DHD Controller Table 6 3 CEC Commands Supported by the DHD Controller Supported V Yes No Opcode Value Initiator Follower Feature Abort 0x00 Y y Standby 0x36 y y Routing Change 0x80 y Y Routing Information 0x81 y y Active Source 0x82 y y Request Active Source 0x85 y y Device Vendor ID 0x87 Y y Give Device Vendor ID 0x8C y y Vendor Command With ID OxAO y y Polling Message N A y y Text View On OxOD Y Report Physical Address 0x84 y Inactive Source Ox9D y
53. cal support representative The customer will need to properly package the defective product consisting of the product only and not include any accessories e g cables remotes carrying cases lens lens cap and other peripherals and return it to the Runco repair depot specified by the technical support representative It is the customer s responsibility to properly package the hardware include all appropriate materials and return it to the location specified by the Runco technical support department The customer will need to address and resolve any shipping damage claims directly with the shipping company The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot Boxes may be purchased from a Runco technical support representative The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot For in warranty repairs Runco will pay freight charges to return the repaired replacement product which shall not include accessories e g cables remotes carrying cases lens cap and other peripherals sold with the Runco product to the customer from the Runco repair depot Once an RMA has been created the customer may contact serviceorders runco com for followup questions or confirmation status of the claim process Warranty Exclusions This RuncoCare Standard Limited Warranty does not include or is limited by the
54. can mode setting Off Crop Zoom 4 3 16 9 Source Image Area Edge Noise ER Screen 16 9 Figure 4 6 Overscan Modes Signature Cinema SC 50d SC 60d Installation Operation Manual 61 Operation Memory Presets Memory Presets ISF Day Custom 1 Custom 2 Save Save Reset Reset Phase RGB Component or SCART sources This control adjusts the phase of the pixel sampling clock relative to the incoming signal Adjust the phase when an RGB Component or SCART image still shows shimmer or noise after Tracking has been optimized A For best results use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels or a similar half on half off graphic image Adjust the slidebar until the image stabilizes and each pixel is clearly defined You may notice that you can stabilize the image at more than one point Use either setting in such cases Adjust the Phase after adjusting Tracking see below Tracking RGB Component or SCART sources Tracking determines the frequency of the pixel sampling clock indicated by the number of incoming pixels per line so that all pixels generated by a particular source are sampled Steady flickering or several soft vertical stripes or bands across the entire image indicates poor pixel tracking Proper pixel tracking helps ensure that the image quality is consis
55. ceed as follows lt Adjust the Anamorphic a Lens Horizontal Position X Adjustment 1 Project a white field on the screen 2 Loosen the Yaw X Adjustment Levers underneath the lens 3 Slowly move the anamorphic lens into place from right to left or vice versa so that there are no shadows on either side of the screen Too Far Left Correct position Too Far Right 4 When the horizontal position is properly set tighten the Yaw X Adjustment Levers to Secure the lens in place Signature Cinema SC 50d SC 60d Installation Operation Manual 47 Installation Adjusting the Height Y With the white field still on screen loosen the Height Y Adjustment T Screws on either side of the lens Then slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen Too Low Correct position Too High When the height is properly set tighten the Height Adjustment T Screws to secure the lens in place Adjusting the Pitch Angle Next angle the lens to even out any top to bottom pincushion distortion To do this loosen the Pitch Adjustment T Screws directly below the Height Y Adjustment T Screws on either side of the lens to allow it to pivot freely Then adjust the anamorphic lens angle so that the projected image is rectangular Correct Lens Angle Incorrect Lens Angle The anamorphic lens will almost always be angled with
56. change the code sent by the remote to match as described below When you change a remote code on the DHD Controller you must re program the DHD Controller remote control to send that same code To do this 1 Press and hold the LIGHT button on the remote control for approximately three seconds or until the LED on the remote lights solid red 2 Enter a new two digit code between 00 and 31 inclusive Include a leading zero for single digit codes for example enter 9 as 09 3 The LED turns off to confirm the code change If you enter an invalid code the LED flashes for three or four seconds Try again entering a valid code Signature Cinema SC 50d SC 60d Installation Operation Manual 77 Operation Operation Sync Threshold Select Sync Threshold to adjust the threshold at which negative pulses on the component video green luma channel are interpreted to be sync pulses Sync Threshold adjustment is occasionally necessary when a DVD player or HDTV source signal drops below black for example during scenes with explosions or when subtitles are present and causes the projector to temporarily lose sync If the sync level from the source is persistently too low the display device won t sync with the source at all The range is from O approximately 60 millivolts mV to 15 approximately 300 mV HDMI Select HDMI from the Service menu to set the following options affecting communication between HDMI sources the
57. d A V receivers introduce additional latency that needs to be compensated for during the installation Table 3 5 shows the amount of possible audio latency given different signal input timings Table 3 5 Possible Audio Latency for Various Input Timings Input Timing Possible Audio Latency milliseconds 480i 133 480p 83 576i 160 576p 100 720p 50 100 720p 60 83 1080i 25 160 1080i 30 133 1080p 24 125 1080p 50 80 1080p 60 67 Signature Cinema SC 50d SC 60d Installation Operation Manual 23 Installation Ventilation x f you are mounting the SC 50d SC 60d in an enclosure leave at least 10 inches 250 mm of space on the left and right sides between it and surrounding objects as shown in Figure 3 6 This allows heat to disperse maintaining the proper operating temperature 250 10 MINIMUM BACK CLEARANCE LAMP AIR OUTFLOW 170 CFM APPROX CARD CAGE POWER SUPPLY AIR INFLOW 170 CFM APPROX LIGHT ENGINE AIR INFLOW 60 CFM APPROX AIR OUTFLOW 60 CFM APPROX 250 10 250 10 m MINIMUM RIGHT SIDE MINIMUM LEFT SIDE j CLEARANCE CLEARANCE Figure 3 6 Ventilation Requirements for Enclosure Mounting Other Considerations y Other considerations and tips that can help improve your installation e Keep the ambient temperature constant and below 35 C 95 F Kee
58. d Installation Operation Manual 0 0 0 0 1 0 2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 x 1 0 Figure 4 7 CIE 1931 Chromaticity Diagram e Simple Select Simple mode from the Color Temp menu to choose one of five color temperature presets 3200K 5500K 6500K 7500K and 9300K The default setting 6500K is appropriate for most situations Higher settings produce a bluer picture lower ones impart a reddish hue to the image Table 4 2 lists the x and y coordinates for each color temperature preset in Simple mode Table 4 2 Color Temperature Presets and Associated Color Points Associated x y Values Color Temperature Preset x y 3200K 0 423 0 404 5500K 0 332 0 348 6500K 0 313 0 329 7500K 0 299 0 315 9300K 0 284 0 298 Signature Cinema SC 50d SC 60d Installation Operation Manual 67 Operation Operation Copy Paste Paste Settings Copied From Input Source HDMI 1 Signal Format 1080p 60 Memory Preset ISF Night e RVR Use the RVR control to increase or decrease the Reflectance Volume Regulation setting RVR lets you adjust the aperture or iris size the physical opening through the lens similar to an f stop on a camera Doing so allows you to optimize brightness and contrast according to the amount of ambient light in the viewing area Use a lower setting larger aperture higher brightness for rooms with a lot of ambie
59. d default gateway of the DHD Controller manually or obtain these settings automatically from a DHCP Dynamic Host Configuration Protocol server Most broadband routers and gateways support DHCP You can also test the network connection from this menu e DHCP To enable the DHCP client in the DHD Controller select DHCP from the IP Configuration menu and set it to On With this setting the DHD Controller s IP address subnet mask and default gateway are assigned by the local DHCP server To manually configure these values set DHCP to Off Configuration menu are disabled grayed out when DHCP is enabled Not The IP Address Subnet Mask and Default Gateway items in the IP ote Signature Cinema SC 50d SC 60d Installation Operation Manual 71 Operation Restore CH mp osite 1 Composite 1 Composite 2 Composite 2 Composite 3 Composite 3 Component Component HD 1 HD 1 HD 2 HD 2 SCART SCART HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3 HDMI 4 HDMI 4 Operation e IP Address Select IP Address from the IP Configuration menu to manually configure the IP Address of the DHD Controller as follows 1 Press A or W to select the first second third or fourth byte of the address 2 Press or 4 to set the value of that byte The range is from O to 255 inclusive 3 Repeat Steps 1 and 2 for all four bytes of the address 4 Press MENU when you have finished setting the address e Subnet Mask Select Subnet Ma
60. de Gain Use the Gain controls to correct color imbalances in the bright areas of the image A good way to do this is to use a test pattern consisting mostly of solid white areas such as an 80 IRE window pattern If the white areas contain traces of red Pr green Y or blue Pr decrease the Gain for that color e Offset Use the Offset controls to correct color imbalances in the dark areas of the image A good way to do this is to use a test pattern consisting mostly of dark gray areas such as a 30 IRE window pattern If the gray areas contain traces of red Pr green Y or blue Pr decrease the Offset for that color Gamma Select Gamma from the Display Color menu to choose a de gamma curve Used correctly the Gamma control can improve contrast while maintaining good details for blacks and whites If excess ambient light washes out the image and it becomes difficult or impossible to see details in dark areas lower the gamma setting to compensate This improves contrast while maintaining good details for blacks Conversely if the image is washed out and unnatural with excessive detail in black areas increase the setting e Mode With the SC 50d SC 60d two Gamma adjustment modes are available Simple or Advanced The two modes are mutually exclusive when you select the Simple mode the Advanced selection in the Gamma menu is grayed out Likewise when you select Advanc
61. ded with the remote control unit The IR control codes have the following characteristics Each code consists of 14 bits e Two 2 start bits always 1 e A toggle bit This bit is inverted every time a key is released and pressed again This allows the DHD Controller to distinguish between a button that remains down and one that is pressed repeatedly e Five 5 address bits The default address is 17 binary 10001 To change it select Remote Code from the Miscellaneous menu in the Service menu and follow the steps given on page 77 e Six 6 data bits e The carrier frequency is 36 kHz with the modulated pulses having a 25 duty cycle Commands are sent at a maximum rate of 9 Hz 90 Signature Cinema SC 50d SC 60d Installation Operation Manual External Control For example here is the RC5 control code for the ON button on the DHD Controller remote control unit assuming the default address is used With Toggle Bit 0 Hex 3 4 4 1 Binary 1 1 0 1 0 0 0 1 0 0 0 0 0 1 With Toggle Bit 1 Hex 3 cC 4 1 Binary 1 1 1 1 0 0 0 1 0 0 0 0 0 1 Function Sta rt Toggle Address Command Bits Bit Figure 6 1 shows the pulse train for this command with the toggle bit set to zero Data Word Start Bits Toggle Bit Address Bits Command Bits Encoded Data Word Modulated Carrier Zoom In of
62. e CEC setting 78 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation Front Panel Brightness Select Front Panel Brightness from the Service menu to adjust the brightness of the front panel LED and LCD status indicators e Logo LED Select Logo LED from the Front Panel Brightness menu to adjust the brightness of the large illuminated logo on the left side of the display The range is from O off to 31 During a firmware upgrade this LED lights at full brightness A Note regardless of the Logo LED setting Standby LED Select Standby LED from the Front Panel Brightness menu to change the behavior of the front panel STANDBY indicator LED When set to ON the LED lights amber when the system is in standby mode otherwise it is off When set to OFF the LED is always off During a firmware upgrade this LED lights at full brightness A Note regardless of the Standby LED setting LCD Select LCD from the Front Panel Brightness menu to adjust the brightness of the front panel LCD The range is from O off to 4 Auto Power Off Select Auto Power Off from the Service menu to have the SC 50d SC 60d turn itself off after a period of inactivity no source signal present e Enable By default Auto Power Off is disabled To enable it select Enable from the Auto Power Off sub menu and set it to On Hours The default time out period is eight 8 hours the range is from 1 to 24 hours System Reset To re
63. e finished editing the input name press ENTER or MENU To restore the default input name press W repeatedly to highlight that input name in the Restore column Then press ENTER Display Device Configure The options in the Display Device Configure menu allow you to change the picture orientation perform lens adjustments or access other display device specific functions e Installation Orientation Select Picture Orientation from the Display Device Configure menu then select Orientation to change the picture orientation to suit the method of installation Floor Front Floor Rear Ceiling Front or Ceiling Rear Or for front projection installations use the Auto setting to have the projector automatically determine the orientation floor or ceiling using an internal sensor e Lamp Info Select Lamp Info from the Display Device Configure menu to see the projector serial number e Diagnostics Select Diagnostics from the Display Device Configure menu then select Red Green Blue Yellow Cyan or Magenta to display only that color channel simulating a filter of that color This can be useful for calibration or measurement purposes To restore the normal picture all colors select White Network The options in the Network menu allow you to configure the network communication features e IP Configuration Select IP Configuration from the Network menu to either set the IP address subnet mask an
64. e to a A Note preset afterwards Otherwise the change will be lost when a different input is selected Picture quality settings are saved for each input and display mode separately For information about saving settings refer to Memory Presets on page 62 Although it may be possible to obtain satisfactory picture guality using the naked eye and regular program material Runco recommends using an external test pattern source Ovation Multimedia Digital Video Essentials or AVIA test DVD or eguivalent for best results Connect your test pattern source to the input that you are calibrating and proceed as follows Perform the adjustments in the order listed here Brightness On your external test pattern source select a PLUGE pattern PLUGE is an acronym for Picture Line Up Generation Eguipment Figure 4 2 shows a typical PLUGE pattern 3 Figure 4 2 Typical PLUGE Pattern for Adjusting Brightness Below Black Above Black 56 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation PLUGE patterns vary but generally consist of some combination of black white and gray areas against a black background The example above includes two vertical bars and four shaded boxes Select Brightness from the Picture menu and press ENTER Adjust the brightness so that e The darkest black bars disappear into the background e The dark gray areas are barely visible e The lighter gray areas are clearly visible e
65. ecessary adjust this setting to eliminate them Noise Filter To apply noise filtering to the input signal select Noise Filter from the Input Color menu The Noise Filter is useful for clearing up noisy images from 480i video sources Use the left or right arrow buttons to select the desired amount of noise reduction keeping in mind that higher settings which reduce high frequencies may also soften the image Save ISF Night Save ISF Day Whenever you make a change to the ISF settings you should always save it Select Save ISF Night or Save ISF Day from the Calibration menu to do this Copy Paste You can copy and paste settings from one memory location to another This gives you a convenient starting point for creating a new preset based on an existing one to make the calibration process less time consuming For example you can use the Copy Paste feature to e Apply settings from HDMI 1 to HDMI 2 or from HD1 to HD2 e Calibrate an input for 720p source signals then use those settings for 1080i sources e Duplicate ISF Night settings for a given source and signal format and save them in the Custom 1 memory preset 68 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation To use this feature select Copy Paste from the Calibration menu Copy Settings Select Copy Settings from the Copy Paste menu to place the settings for the current input source signal format resolution and frame ra
66. ect it Brightness Contrast Color saturation Tint Sharpness Gamma Lamp Settings Color temperature and white balance ISF Day on page 68 press lt or p to highlight Reset and press ENTER Select Sleep Timer from the Main Menu to turn off the SC 50d SC 60d after a specified interval Press A or W to select Off 30 Minutes 60 Minutes 90 Minutes 2 Hours or 4 Hours Then press ENTER Signature Cinema SC 50d SC 60d Installation Operation Manual To save the settings for the current input and display mode to the ISF Night or ISF Day memory preset select Save ISF Night or Save ISF Day from the Calibration menu refer to Save ISF Night Save 63 Operation lt Sleep Timer Sleep Timer gt C 30 Minutes 60 Minutes 90 Minutes 2 Hours 4 Hours Operation Information y Information System Network Field Service Manufacturing MAC Address 1A 2B 3C 4D 5E 6F P Address 192 168 0 150 Subnet Mask 255 255 0 0 Default Gateway 192 168 1 1 DHCP Enabled Network Status Connected Signal System Select Information from the Main Menu then choose either Signal or System to display information about the current input signal resolution frequency type et cetera and installed firmware versions as well as other information that uniquely identifies your DHD Controller and display device Should you ever need to contact Runco Technical Support this information wil
67. ed the Simple selection is grayed out Simple Use the Simple Gamma control to perform gamma correction at the display according to a simple power law gamma function The value chosen here corresponds to the power variable in this equation Output InputPower The DHD Controller applies this gamma curve to all three primary color channels red green and blue e Advanced To select a custom gamma curve select Mode from the Gamma menu and set it to Advanced Then select Advanced from the Gamma menu to select one of up to 20 pre programmed gamma tables Custom gamma tables provide the ability to perform complex non linear gamma correction on each primary color channel independently of the others Signature Cinema SC 50d SC 60d Installation Operation Manual 65 Operation Calibration Calibration ISF Settings MA Input Image Input Color Save ISF Night Save ISF Day Copy Paste Output Shift Splash Configure OSD Position Operation e Lamp Select Lamp from the Display Color menu to adjust the projector lamp brightness Mode With the SC 50d SC 60d two lamp adjustment modes are available Power recommended or Intensity The two modes are mutually exclusive when you select the Power mode the Intensity selection in the Lamp menu is grayed out Likewise when you select Intensity the Power selection is grayed out Power To supply a constant wattage to the lamp select Mode from the Lam
68. ema SC 50d SC 60d Installation Operation Manual Installation 3 Installation Installation must be performed by a qualified custom video A Note installation specialist To install batteries in the remote control 3 1 1 Press down the tab on the cover and Remote Control pull the cover in the direction of the arrow 2 Insert the included batteries Ensure that the polarities correctly match the CD and markings inside the battery compartment 3 Insert the lower tab of the cover into the opening and press down the cover until it clicks in place e Make sure that the battery polarities are correct when installing the batteries lt Notes on Batteries e Do not mix an old battery with a new one or different types of batteries e f you will not use the remote control for a long time remove the batteries to avoid damage from battery leakage e Do not expose batteries to excessive heat such as from sunshine fire or the like Signature Cinema SC 50d SC 60d Installation Operation Manual 15 Installation Notes on Remote Control y Make sure that there is nothing obstructing the infrared beam between the remote Operation control and the IR receiver on the DHD Controller e lf the effective range of the remote control decreases or it stops working replace the batteries with new ones e The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or
69. fluorescent lighting e Ambient conditions may possibly impede the operation of the remote control If this happens point the remote control at the DHD Controller and repeat the operation 3 2 Table 3 1 gives a quick overview of the SC 50d SC 60d installation process The sections Quick Setup following this one provide detailed instructions Table 3 1 Installation Overview Step Procedure For Details Refer to page 1 Choose a location for the projector 17 2 Install primary projection lens 25 3 Install CineWide with AutoScope lens motor optional 26 38 4 Mount the projector 27 5 Connect the DHD Controller to the projector 29 6 Connect signal sources to the DHD Controller 31 Connect other external equipment to DHD Controller optional 36 e Audio processor or secondary display device e Control system interface RS 232 7 e 12 volt trigger activated equipment AutoScope lens motor retractable screens or screen masking etc e External IR repeater Network hub router or gateway Ethernet 8 Apply power to the projector 40 41 9 Adjust primary lens projected image size zoom position shift 19 41 and focus 10 For rear screen and or ceiling mount installations select the 42 proper picture orientation 11 Use Image Alignment controls to fine tune image geometry 43 12 Install CineWide anamorphic lens optional 45 13 Adjust CineWide anamorphic lens position pitch angle 47 geometr
70. following a 2 3 4 Products not purchased from an authorized Runco dealer Rental costs incurred by the customer in the event of product defect or failure Any product with a defaced modified or removed serial number Damage deterioration or malfunction resulting from a Accident abuse misuse neglect improper ventilation fire water disaster lightning or other acts of nature smoke exposure cigarette or otherwise unauthorized product modification including use of an unauthorized mount or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by Runco Any damage to the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuations or failure 0o Oo O o Use of supplies or parts including lamps that are not purchased from Runco or do not meet Runco s specifications Normal wear and tear Q iv Signature Cinema SC 50d SC 60d Installation Operation Manual h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed i Customer caused defects including but not limited to scratched defaced altered plastics j Failure to follow maintenance procedures as outlined in the product s user guide where a schedule is specified for regular cleaning of the product k Opening the product and or tampering with internal circuitry Products lost sto
71. function p CAUTIONS alert users that a given action or omitted action can A Caution in damage to the equipment or possible non fatal injury to the user WARNINGS appear when a given action or omitted action can result A WARNING DANGER appears when a given action can cause severe injury or 4 DANGER death Use the following table to locate the specific information you need in this manual If you need Information about obtaining service General information about the Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller Installation instructions First time configuration instructions Advanced configuration instructions Troubleshooting tips Specifications for the Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller 41 65 83 97 Turn to page 2 Signature Cinema SC 50d SC 60d Installation Operation Manual Offering the best in high end luxury projection the new Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller expands Runco s most prestigious line of custom built personal cinema projectors The SC 50d and SC 60d join Runco s legendary SC 1 and offer the best cinematic experience available for the most sophisticated private cinemas The Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller offers exceptional performance with a state of the art product that prov
72. gnal Auto Calibration allows you to quickly get the image in the ballpark after which you can perform further calibration if necessary To perform an Auto Calibration select Display Device from the Service Menu Then select Auto Calibration and set it to Yes What an Auto Calibration Does Auto Calibration sets the following parameters to their default values e Contrast and Brightness e Auto Input Level off e Detail if video source e Filter e Luma Delay Auto Calibration also optimizes the following settings based on the characteristics of the incoming signal e Pixel Tracking e Pixel Phase e Size and Blanking e Vertical Stretch e Position e Input Levels If additional fine tuning is necessary after performing an Auto Calibration use the controls in the Picture menu refer to page 56 or Calibration menu refer to page 65 Signature Cinema SC 50d SC 60d Installation Operation Manual 75 Operation Color Space Select Color Space from the Service menu to choose the color space of the source signal for HDMI RGB and component connections e The default setting Auto functions as follows HDMI If the Auxiliary Video Information AVI infoframe contains color space and or range data the DHD Controller uses that information Otherwise for RGB sources the DHD Controller uses the RGB Video color space For component SDTV and EDTV resolutions REC601 is used For other component video resolutio
73. hat the AC active outlet is active e The motor is not e Check the trigger connected to a trigger connection between the output on the DHD lens motor and DHD Controller Controller Figure 3 17 e Incorrect trigger e Correct the trigger assignment assignment refer to Installing and Adjusting the CineWide Anamorphic Lens on page 45 84 Signature Cinema SC 50d SC 60d Installation Operation Manual External Control 6 External Control In addition to using the DHD Controller front panel keypad or remote control unit there are three methods of controlling the SC 50d SC 60d and DHD Controller externally e Using a serial RS 232 link to send ASCII commands and receive responses to those commands e Using discrete infrared IR codes to program a third party remote control unit e Using an HDMI connection to send Consumer Electronics Control CEC commands from a BD player or other source component that supports CEC The following sections describe these methods The DHD Controller uses a simple text based control protocol to take requests from control devices and to provide responses to such devices This section describes how to send control messages over a serial link between the DHD Controller and an automation control system or a PC running terminal emulation software Connect your control system or PC to the RS 232 input of the DHD Controller as shown in Figure 3 17 Configure the RS 232 contro
74. he projector can rest A variety of materials can be used for this purpose for example rubber crutch tips or turntable feet Signature Cinema SC 50d SC 60d Installation Operation Manual 27 Installation 3 6 Mounting the SC 50d SC 60d lt Floor Mounting Upright lt Ceiling Mounting Inverted lt Installing the Projector in an Enclosure Installation Adjusting the Projection _ If the screen is significantly higher or lower than the projector you can also tilt the Angle projector at a slight angle In a ceiling installation you do this by adjusting the ceiling mount For a floor installation turn the adjustable feet at the bottom of the projector to adjust the projection angle The projector can be rotated front to back up to 360 degrees and mounted without it affecting performance However to ensure optimal performance of the lamp limit the side to side tilt of the projector to 20 degrees see Figure 3 8 Figure 3 8 Mounting Angle Ranges Front to Back and Side to Side If you do this you may need to vertically shift the image to compensate For detailed instructions refer to Primary Lens Adjustments Focus Zoom and Position on page 41 28 Signature Cinema SC 50d SC 60d Installation Operation Manual Proceed as follows to connect the DHD Controller to the SC 50d SC 60d your video sources external controller s if present and AC power When connecting your egui
75. hinese Simplified Chinese Portugu s or Russian OSD Timer Select OSD Timer from the Miscellaneous menu to set the OSD Timer which controls how long the menus remain on screen after selecting them Select from 5 to 60 seconds in one second increments Or set the timer to O disabled if you want the menus to remain on screen indefinitely OSD Messages When you select a new aspect ratio input source or memory preset the DHD Controller briefly displays an on screen message confirming your new selection To prevent the display of these messages select OSD Messages from the Miscellaneous menu to and set it to Off Blank Screen Color Select Blank Screen Color from the Miscellaneous menu to select the color that appears when no incoming signal is present The range is from O to 255 inclusive for each color component red green and blue Sidebar Color Select Sidebar Color from the Miscellaneous menu to change the color of the inactive image area The range is from O to 255 inclusive for each color component red green and blue The inactive image area is on either side of the active image area when using the 4 3 aspect ratio 76 Signature Cinema SC 50d SC 60d Installation Operation Manual e Film Mode Use Film Mode to smooth out moving images from interlaced standard definition SD sources In most cases the DHD Controller detects the proper pull down rate and vertical frequency However if your source is
76. hipped with the A WARNING _ SC 50d SC 60d for this purpose the one with the ferrite sleeve Doing otherwise creates a fire hazard risk Signature Cinema SC 50d SC 60d Installation Operation Manual 7 Controls and Functions 2 3 Figure 2 3 shows the controls and indicators on the DHD Controller front panel the DHD Controller Front paragraphs that follow describe them Panel H HIGH DEFINITION DIGITAL VIDEO CONTROLLER PROCESSOR 7 HD A SERIES RUNCO Wn pem SC 50d SC 60d HDMI 1 1080i 60 Figure 2 3 DHD Controller Front Panel 1 RUNCO ICON Lights blue to indicate that the controller is on or powering up IR SENSOR Receives IR commands from the remote control VACUUM FLUORESCENT DISPLAY Can be used instead of the On Screen Display OSD Displays currently selected menu or if no menu is selected the connected display device model current source input resolution and aspect ratio ON STANDBY BUTTON Press once to toggle from standby mode to on mode Press it again to return to standby mode For a discrete on or off command you can use the direct access buttons on the remote control LEFT BUTTON Used to direct select inputs or move the OSD menu cursor to the left When no menu is present on screen the LEFT button toggles through the different sources in this order HDMI 4 HDMI 3 HDMI 2 HDMI 1 SCART HD 2 HD 1 Component Composite 3
77. hout lens Regulatory Approvals Limited Warranty 200W SC 50d or 350W SC 60d HPM lamp 100 VAC to 240 VAC 10 amp 50 60Hz SC 50d 1135W maximum Current 11 4A 100V C 60d 1320W maximum Current 13 2A 100V 10 C to 40 C up to 7 500 altitude 10 C to 35 C 7 500 to 10 000 altitude 10 80 humidity non condensing See Figure 7 1 and Figure 7 2 135 Ibs 61 24 kg FCC Part 15 Subpart B Class A UL 60950 IEC60950 RoHS Two 2 year PremierCare warranty lamp warranty 1000 hours or 6 six months whichever comes first US and Canada only Specifications are subject to change without notice 98 Signature Cinema SC 50d SC 60d Installation Operation Manual Specifications Table 7 2 lists the DHD Controller specifications 7 2 Table 7 2 DHD Controller Specifications Aspect Ratios Video Standards Inputs Outputs Control Options Ethernet Communication RS 232 Communication Parameters Trigger Outputs Accessory Applications Power Requirements Operating Environment Dimensions Weight DHD Controller Specifications 4 3 Letterbox 16 9 VirtualWide Cinema Virtual Cinema Native e HDMI and DVI with HDCP for digital video e Component and RGB HDTV 1080p 1080i 720p e Component and RGB EDTV 576p 480p e Component and Composite SDTV 576i 480i e RGB SCART with adaptor e NTSC M 4 43 e PAL B G H N M e SECAM M
78. ice Menu passcode A Note You must enter a passcode to access the Service menu Select Display Device from the Service Menu Select Configure from the Display Device menu then select Installation Select Orientation then choose Floor Rear Ceiling Front or Ceiling Rear to match the installation method 42 Signature Cinema SC 50d SC 60d Installation Operation Manual Projector and or screen placement among other things can cause geometric distortion in the projected image To correct this the DHD Controller provides precise nine point control over the projected image geometry Use these controls as and only if needed to re position the image corners mid points and center to eliminate keystoning mis aligned corners or pincushion distortion mid points not aligned with corners See Figure 3 21 Horizontal Keystoning Vertical Keystoning t Pincushion Distortion y t y SS U y Y U Y 1 m 1 E x 4 1 E U E Y 1 V a v Xx uua ae aa i sos 4 a ie ee C rt x fe Figure 3 21 Keystone and Pincushion Distortion Signature Cinema SC 50d SC 60d Installation Operation Manual 43 Installation 3 11 Adjusting the Image Geometry Installation Keystoning usually occurs when the projector is tilted relative to the screen Pincushion distortion can sometimes occur if the throw distance is very short and or the projector is equipped
79. ics Magenta Display Device Auto Yes No Calibration P Configuration DHCP On Off IP Address Subnet Mask Default Gateway Communication Test Auto Firmware Upgrade Auto Check for New Firmware Auto Perform Upgrade Check for New Firmware Network FEN E Mail Address Error Notification Error Notification to Runco Periodic Service E Mail Notification Notification Lamp Life Notification Customer Information E Mail Calibration Data Remote Network Control On Off Color Space Auto REC601 REC709 Not available on Composite 1 p RGB PC or RGB Video Composite 2 or Composite 3 inputs Triggers 1 2 83 Miscellaneous English Francais Deutsch Italiano Language Espa ol Svenska Traditional Chinese Simplified Chinese Portugu s or Russian OSD Timer O no timeout or 5 6 7 15 60 sec OSD Messages On Off Blank Screen Color Red Green Blue 0 1 2 3 255 Chroma Upsampling Error Sidebar Color Film Mode SD sources only On Off CUE On Off Remote Code 00 01 02 17 31 Sync Threshold 0 1 2 15 HD 1 HD 2 and Component inputs only HDMI EDID Extension On Off per HDMI input HDMI Audio Format Combined HDMI Out To Display HDMI Out Audio Only CEC On Off Logo LED O off 1 2 31 Front Panel Brightness Standby LED On Off LCD O off 1 2 30r 4 Enable On Off Auto P
80. icular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help INDUSTRY CANADA ICES 003 This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada PRODUCT DISPOSAL The Product contains small amounts of tin lead and or mercury Disposal of these materials may be regulated due to environmental considerations IMPORTANT RECYCLE INSTRUCTIONS Lamp s inside this product contain mercury This product may contain other electronic waste that can be Hg hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT Applicable throughout the European Union and other European countries with separate collection programs
81. ides an extraordinary cinematic experience The Signature Cinema experience surpasses even the most renowned public theaters because the product and room are custom built with the finest components to exactly match an owner s specifications Combined with the unique and flexible engine design the SC 50d SC 60d provides better richer color performance for pristine color accuracy These benefits combine into a brilliant image that provides a spectacular color gamut and contrast as well as unmatched color brightness even on the largest screen sizes For unparalleled reproduction of Hollywood s 2 35 1 CinemaScope standard the SC 50d SC 60d is available with Runco s legendary CineWide with AutoScope technology Selecting from multiple lens options that allow the flexibility for seamless integration into the most sophisticated personal cinemas each SC 50d SC 60d projector is custom built to suit the exact requirements specified for every client The SC 50d SC 60d features 1080p HD native resolution 3 chip system for the finest projection image and 16 9 native aspect ratio to match all digital programming including seamlessly switching aspect ratios for all media including broadcast film sports and gaming CineWide requires the use of a 2 35 1 or similar aspect ratio A Note superwide format screen Signature Cinema SC 50d SC 60d Installation Operation Manual 3 Introduction 1 3 Description Feat
82. l free 800 23RUNCO 800 237 8626 Signature Cinema SC 50d SC 60d Installation Operation Manual v Online Product Registration Please visit http www runco com support product registration to register product Limitation of Implied Warranties RUNCO PROVIDES NO WARRANTIES EXPRESS OR IMPLIED EXCEPT THOSE EXPRESSLY PROVIDED HEREIN RUNCO EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Exclusion of Damages RUNCO S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT 1 RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT DAMAGES BASED UPON INCONVENIENCE LOSS OF USE OF THE PRODUCT LOSS OF TIME LOSS OF PROFITS LOSS OF BUSINESS OPPORTUNITY LOSS OF GOODWILL INTERFERENCE WITH BUSINESS RELATIONSHIPS OR OTHER COMMERCIAL LOSS EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL INCIDENTAL INDIRECT SPECIAL OR PUNITIVE DAMAGES RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY no e Effect of Local Law This warranty gives you specific legal rights and you may have other rights which vary from locality to locality Some localities do not allow limitations on implied warranties and or do not allow the exclusion of incidental or consequential damage
83. l help them answer your questions or resolve product performance issues Input Source HDMI 1 Model DHD4 Signal Format 1080p 60 Display Name SC 50d SC 60 Input Resolution 1920x1080 d Vertical Freq 59 94 Hz Output Resolution 1920x1080 Horizontal Freq 67 500 kHz Serial Number 00000000 Pixel Clock 148 500 MHz Boot Version 4 0 Color Space REC709 Firmware Version 4 0 Sync Type Separate Micro Version 4 0 Memory Preset ISF Night Network Select Information from the Main Menu then choose Network to display information about the Ethernet network connection To enable network communication via Ethernet refer to IP Configuration on page 71 Field Service Manufacturing The Field Service and Manufacturing menus are password protected and intended for use only by Runco service personnel and factory technicians 64 Signature Cinema SC 50d SC 60d Installation Operation Manual Use the Calibration menu to perform advanced picture quality adjustments This menu should be used by ISF certified technicians only A Note To recall the ISF Night or ISF Day settings select ISF Night or ISF Day from the Memory Presets menu See page 62 or use the corresponding remote control buttons You must enter a passcode to access the Calibration menu Display Color Use the Display Color settings to adjust the color balance at the DHD Controller output These settings are saved independently for each input and display mo
84. len or discarded m Any damage or dissatisfaction associated with latent images burnin or any other damage determined by Runco to be the result of customer use patterns n Any other cause which does not relate to a product defect in material or workmanship Removal installation and setup service charges are excluded from this Standard Limited warranty Black uniformity issues or other LCD issues associated with usage outside the Runco recommended guidelines and specifications for the product 7 Bright or dark sub pixels that are characteristic of LCD technology and considered by Runco to be acceptable and within Runco s manufacturing specifications See Sub Pixel Policy below 8 Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver to PO Box and FPO Box addresses Sub Pixel Policy It is not uncommon for one or more sub pixels to become bright or dark during or after the manufacturing process A bright sub pixel is one that remains in the on position and a dark sub pixel is one that appears black or off The sub pixels are usually hard to see and will not detract from the display quality or usability at normal viewing distance The following are Runco s criteria for identifying bright or dark sub pixels that would be considered unacceptable a the number of bright or dark sub pixels b the location of the bright or dark sub pixels c the color of the brigh
85. list of products excluded from this warranty from time to time at Runco s sole discretion but updates to the list of covered products will not apply on a retroactive basis 2 MSRP is defined as the most recent product price listed on Runco s price list Signature Cinema SC 50d SC 60d Installation Operation Manual lij RuncoCare Claim Procedure In the event of a product defect please follow the warranty claim procedure provided below 1 The Customer is required to contact a Runco dealer or Runco Technical Support via email at supportOrunco com or via phone at toll free 800 23RUNCO 800 237 8626 If the customer is located outside North America call 3589 4200 554 in Europe for product service Be prepared to provide the date of purchase the place of purchase serial number product model number description of the problem and troubleshooting steps already attempted Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem If Runco is unable to resolve the problem through troubleshooting a Return Material Authorization RMA number will be issued for the exchange of the defective product if it is determined that the claim was made within the coverage period of the Standard Limited Warranty If it is determined that the Standard Limited Warranty applies to the claim the customer will need to return the defective product to the Runco repair depot location specified by the Runco techni
86. ller or PC serial port as follows no parity 8 data bits 1 stop bit and no flow control Set the baud rate to 19200 to match that of the DHD Controller RS 232 port Serial commands to the DHD Controller take the following form e Commands are not case sensitive e For a single command that takes no parameters type the command followed by a carriage return for example to set the aspect ratio to Letterbox type LETTERBOX lt Enter gt For a single command that takes a parameter type the command a space or a comma and the desired value followed by a carriage return for example to set the brightness to 10 type BRIGHTNESS 10 lt Enter gt or BRIGHTNESS 10 lt Enter gt You can also send a string of multiple commands on a single line separated by commas For example COMPOSITE BRIGHTNESS 50 16 9 lt Enter gt switches to the Composite video input sets the brightness to 50 and sets the aspect ratio to 16 9 Command strings can be up to 255 characters long on a Single line After sending ON or POWER 1 allow at least five 5 seconds for the DHD Controller to power up If you have enabled the ISF splash screen refer to Splash Configure on page 69 allow 15 seconds for the DHD Controller to power up Avoid combining the ON or POWER 1 commands with other commands A Note Once it does it will accept and properly execute multiple serial commands Signature Cinema SC 50d SC 60d Install
87. mage that completely fills the screen Ideally the projector should be positioned perpendicular to the screen and in such a way that the lens center is aligned with either the top or bottom edge of the screen area and centered horizontally See Figure 3 2 Ceiling Installation 7 Ceiling Projection Distance Lens Center Height 6 Lens Center Screen Floor Installation Height Screen Tae Center Projection Distance Lens Center Figure 3 2 Projector Placement You can use the lens shift controls to center the image on the screen Lens shift is generally expressed as a percentage of the screen height or width as shown in Figure 3 3 and Figure 3 4 Screen Center So 50 Height Lens Shift 0 5 x H Sw gt cs 100 Height gt XN EXE Lens Shift 1 0 x H AN Ss ue Note This is a general example of lens shift Lenses vary in their shift capabilities No particular lens or projector is used in this example Figure 3 3 Vertical Lens Shift EXAMPLE ONLY Signature Cinema SC 50d SC 60d Installation Operation Manual 19 Installation Vertical and Horizontal Position Vertical and Horizontal Lens Shift Installation 100 Width Lens Shift 50 Width Lens Shift Screen Center Note This is a general example of lens shift Lenses vary in their shift capabilities No particular len
88. menu and set it to On Signature Cinema SC 50d SC 60d Installation Operation Manual 73 Operation Operation Periodic Service Notification You can have the DHD Controller send periodic reminders via e mail to perform regular maintenance tasks To do this Select Periodic Service Notification from the E Mail Notification menu Highlight Enable and press ENTER Highlight On and press ENTER Press MENU Highlight Timer and press ENTER Press or lt q to set the notification interval in months The range is from 1 to 255 inclusive the default is 12 months 7 Press MENU Lamp Life Notification To have the DHD Controller send a message to the destination e mail address when the lamp hour counter reaches a certain threshold select Lamp Life Notification from the E Mail Notification menu Then 1 Highlight Enable and press ENTER Highlight On and press ENTER Press MENU Highlight Lamp Hours and press ENTER o v SO uo eS Cr xm Press p or lt to set the notification threshold in hours The range is from 100 to 10 000 hours the default is 1 000 hours 6 Press MENU Customer Information Select Customer Information from the E Mail Notification menu to supply this information to the DHD Controller which includes it in all e mail notification messages Six lines up to 30 characters per line of text are provided use them however you wish 1 Press A or W repeatedly to select a line of text to edi
89. nce of REFER SERVICING TO QUALIFIED important operating and maintenance servicing instructions in the SERVICE PERSONNEL literature accompanying the appliance Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth Do not block any of the ventilation openings Install in accordance with the manufacturer s instructions ON Oar ON Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety When the provided plug does not fit into your outlet consult an electrician for the replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use the attachments accessories specified by the manufacturer 12 Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus to avoid injury from tip over 3 Unplug this appara
90. nel The SC 50d SC 60d OSD menus are arranged hierarchically as shown in Figure 4 1 Some menu options apply only to certain input signal types For example Phase and Tracking can only be adjusted for RGB Component video or SCART signals Composite 1 Signal Composite 2 System read only Composite 3 Information Network Component Field Service HD 1 Manufacturing Gai Input Source rb n 100 99 0 99 100 Red Green Blue SCART Offset HDMI 1 Mode HDMI 2 Simple Advanced Simple HDMI 3 Gamma 1 00 1 01 1 02 2 20 3 38 3 39 3 40 HDMI 4 Advanced 16 9 0 2 2 gamma curve 4 3 1 2 3 20 custom gamma tables Letterbox Display Color Mode Aspect Ratio VirtualWide Power recommended Intensity Enema Li RN 150 151 152 200W 7 amp 1 A a Virtual Cinema SC 60d 300 301 302 350W 370 Native Intensity Brightness 0 1 2 9999 Contrast cm Simple Pictur Color oM emp 8200K 5500K 6500K 7500K or 9300K cture Tint RVR 0 1 2 9 Sharpness Brightness Noise Filter Contrast Left Right Calibration Input Image Color 50 49 0 49 50 Up Down Tint Width Sharpness Height Gain 32 31 0 31 32 Overscan Offset HD 1 HD 2 and Component inpu
91. nete ee doe 81 6 1 RC5 Message FOITriat m ene otro ciere ated e e eed vy os Ee e Peer eee o dia 91 71 96 50d SC 60d DIMENSIONS iie te e t m Op POR gd Yd 101 7 2 SC 50d CineWide with AutoScope and SC 60d CineWide with AutoScope A eaa EET 102 xvi Signature Cinema SC 50d SC 60d Installation Operation Manual Introduction 1 Introduction This Owner s Manual describes how to install set up and operate the Runco Signature 1 1 Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller About This Manual Throughout this manual the Runco Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller is referred to as the SC 50d SC 60d Runco has prepared this manual to help installation personnel and end users get the most Target Audience out of the SC 50d SC 60d Runco has made every effort to ensure that this manual is accurate as of the date it was printed However because of ongoing product improvements and customer feedback it may require updating from time to time You can always find the latest version of this and other Runco product manuals on line at www Runco com Runco welcomes your comments about this manual Send them to support Runco com lt lt If You Have Comments About This Manual Text Conventions The following conventions are used in this manual in order to clarify lt Textual and Graphic the information and instructions provided Conventions
92. ns REC709 is used e RGB If Hsync or Vsync signals are present the DHD Controller uses the RGB PC color space Otherwise REC601 is used for SDTV and EDTV sources and REC709 for all other sources e Component For SDTV and EDTV resolutions the DHD Controller uses the REC601 color space For all other resolutions REC709 is used In most cases the Auto setting determines the correct color space to use If it does not you can force the DHD Controller to use a specific color space Choose one of the following REC709 sets the color space matrix to that defined in ITU R BT 709 REC601 sets the color space matrix to that defined in ITU R BT 601 RGB PC uses RGB color space and sets black at 0 0 0 RGB and white at 255 255 255 RGB assuming an 8 bit image RGB Video uses RGB color space and sets black at 16 16 16 RGB and white at 235 235 235 assuming an 8 bit image to correspond to the luminance values defined in digital component standards Triggers Select Triggers from the Service menu to configure the 12 volt trigger outputs You can assign one or more trigger outputs to each aspect ratio Those triggers are then activated by selecting that aspect ratio Miscellaneous Select Miscellaneous from the Service menu to set the following options Language Select Language from the Miscellaneous menu and press the up or down arrows to select the OSD Language English Frangais Deutsch Italiano Espanol Svenska Traditional C
93. ns should appear as a tall narrow oval Signature Cinema SC 50d SC 60d Installation Operation Manual 49 Installation Verify Proper Image Alignment with Anamorphic Lens 3 13 Working With the Lamp Focus Finally rotate the Focus Ring on the anamorphic lens to fine tune the optical focus After you have installed the anamorphic lens ensure that the 2 35 1 image corners and edges are aligned with the screen with no geometric distortion Use the Image Alignment controls to make any necessary adjustments refer to Adjusting the Image Geometry on page 43 At this point you may want to check and adjust the following settings to optimize lamp performance Choose a lamp mode for regulating power and light output Change the optical aperture size To access them choose Calibration from the Main Menu and enter the Calibration menu passcode Then choose Display Color gt Lamp refer to Lamp on page 66 or Display Color gt RVR refer to RVR on page 68 50 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation 4 Operation To display the Main Menu press the MENU button on the remote control or DHD 4 1 Controller front panel Figure 2 3 Using the On Screen To select a menu item use the A and W buttons on the remote control or DHD Controller Menus front panel to highlight it Then to confirm your selection press ENTER on the remote control or DHD Controller front pa
94. nsidering this type of installation contact your dealer for assistance Mirror Figure 3 5 Folded Optics rear projection installation as opposed to conventional second surface mirrors with the reflective surface behind a transparent substrate such as glass or acrylic For best performance always use first surface mirrors in your y Tip First surface mirrors provide a strict reflection without the ghosting effect seen with a second surface mirror where a faint secondary reflection could be observed coming from the front surface of the glass 22 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation Due to its extraordinarily high level of video processing performance the DHD Controller lt Audio Video may distribute video signals with a perceptible level of audio latency In order to easily Synchronization Issues solve this issue Runco recommends using the DHD Controller with a high quality audio receiver that has the ability to effectively synchronize audio and video signals Most mainstream audio receiver switchers have the ability to synchronize the audio and video to the Advanced Television Systems Committee ATSC prescribed tolerances According to the ATSC the sound program should never lead the video program by more than 15 milliseconds and should never lag behind the video program by more than 45 milliseconds In addition many video displays an
95. nt light Use a higher setting smaller aperture higher contrast for more theater like viewing conditions little or no ambient light RVR can only be used with the Power Lamp Mode setting refer A Note to Lamp on page 66 Input Image The Input Image controls are functionally similar to those in the Picture menu refer to page 56 but are accessible only by entering the Calibration menu passcode The Input Image settings establish the zero point for the Picture A Note menu settings whose values represent offsets from the Input Image settings For example if you set Brightness to 10 in this menu setting Brightness to 10 in the Picture menu results in an actual setting value of 20 10 10 Input Color The Input Color controls are similar to those in the Display Color menu see above but adjust the color balance of the incoming signal These settings are also saved independently for each input and display mode e Gain Offset HD1 HD2 and Component SCART inputs only These controls operate similarly to those in the Display Color menu described on page 65 but affect the Y Pb and Pr signal components rather than the red green and blue channels e Chroma Delay use the Chroma Delay control to correct a mis aligned image from a composite video source Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions producing artificial shadows or a halo effect If n
96. o cool down for approximately 15 minutes prior to removing the lamp assembly for replacement 2 Remove the four screws securing the Left Exhaust Side Panel see Figure 2 1 to the projector Then remove the panel 3 To open the lamp compartment cover Using a Phillips screwdriver turn the captive screw on the lamp compartment cover counter clockwise to access the lamp compartment See Figure 5 1 Lamp Compartment Cover Retaining Screw Figure 5 1 Opening the Lamp Door 4 Remove the old lamp a Unscrew the three 3 captive screws securing the lamp using a 1 Phillips screwdriver b Carefully remove the lamp from the projector Place the old lamp in a location where it cannot fall or be bumped safety regulations for your area Discard the lamp using safe disposal recycling practices or contact your Runco dealer for a possible re lamping program Handle lamps with extreme caution Dispose of lamps according to A WARNING Signature Cinema SC 50d SC 60d Installation Operation Manual 81 Maintenance and Troubleshooting 5 Install the new lamp a Take care to align the new lamp properly in the correct orientation inside the lamp compartment b Press firmly on the lamp to properly seat it c Secure the lamp by tightening the three 3 captive screws 6 Close the lamp compartment cover and tighten the captive screw Not The lamp will automatically t
97. o the Component input and set to progressive scan mode Incorrect aspect ratio selection Solution e Ensure that the SC 50d SC 60d is plugged in and switched on and that the AC outlet is active e Ensure that the DHD Controller is plugged in and switched on and that the AC outlet is active e Replace the batteries e Ensure that the RS 232 output from the DHD Controller is properly connected to the RS 232C input on the SC 50d SC 60d see Figure 3 10 Ensure that the lens cover is off and the shutter is open e Ensure that the lamp door is closed If it is and the problem persists replace the lamp e Ensure that the HDMI output from the DHD Controller is properly connected to the Slot 2 DVI I input on the SC 50d SC 60d see Figure 3 10 Select the correct source e Turn on the source component e Check connections from source component to DHD Controller e Turn off progressive scan on the DVD player Or connect the DVD player to the HD1 or HD2 input e Select a different aspect ratio Signature Cinema SC 50d SC 60d Installation Operation Manual 83 Maintenance and Troubleshooting 5 2 Troubleshooting Tips Maintenance and Troubleshooting Table 5 1 Troubleshooting Chart continued Symptom The display is jittery or unstable Image is too bright and or lacks definition in the bright areas of the image Image appears
98. om the Main Menu and press ENTER 10 Select Color from the Picture menu and press ENTER 58 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation 11 Adjust the color saturation level until the outermost gray and blue color bars appear to be a single shade of blue lt Tall color bars lt Short color bars NES Tint Color Tint Tint or hue is essentially the ratio of red to green in the color portion of the image When tint is decreased the image appears redder when it is increased the image appears greener To adjust the tint enable blue only display mode in the Diagnostics menu as you would for adjusting color saturation refer to the previous section Color Saturation Select Tint from the Picture menu and press ENTER Adjust the tint level until the cyan and magenta color bars on either side of the green bar appear to be a single shade of blue Like the brightness and contrast controls the color and tint controls A Note are interactive A change to one may require a subtle change to the other in order to achieve the optimum setting Signature Cinema SC 50d SC 60d Installation Operation Manual 59 Operation Input Position Input Position ES Up Down Width Height Overscan Overscan Mode Phase Tracking Sharpness Sharpness is the amount of high frequency detail in the image To adjust sharpness select Sharpness from the Picture menu and
99. on are motorized adjustments that are adjustable using the Setup remote control Figure 2 6 This allows you to adjust the focus and image size while at the screen for more accurate results For maximum range point the remote directly at the projector y Tip To access the lens controls press the MAIN button on the Setup remote control to display the Main Menu page if not already displayed Then Focus To focus the projected image press FOCUS then press and hold the FCUS A or FCUS button e Zoom To make the picture smaller zoom out press ZOOM then press and hold the ZOOM button To enlarge the picture zoom in press and hold the ZOOM button e Lens Shift To change the lens and projected image position press LENSS then press and hold the LENS A LENS LENSp or LENSW button Signature Cinema SC 50d SC 60d Installation Operation Manual 41 Installation 3 8 Turning on the Power 3 9 Primary Lens Adjustments Focus Zoom and Position Installation 3 10 By default the SC 50d SC 60d is configured for a floor front installation in which the Adjusting the Picture projector is installed upright and in front of the screen If it is installed behind the screen Orientation and or mounted on a ceiling you must change the picture orientation To do this 1 On the DHD Controller remote control or front panel press MENU 2 Select Service from the Main Menu and enter the Serv
100. ower Off Hours 1 2 3 4 8 23 24 System Reset Figure 4 1 SC 50d SC 60d OSD Menu Structure continued 52 Signature Cinema SC 50d SC 60d Installation Operation Manual The Main Menu is the starting point for accessing all DHD Controller functions You must enter a passcode to access the Calibration and Service menus From the Main Menu select Input Source to choose a video signal source The active source is indicated by an arrow 9 to its left in this example Composite is the active source To change the aspect ratio size and shape of the projected image select Aspect Ratio from the Main Menu and press ENTER Select the appropriate aspect ratio for your screen size and the type of program material being viewed refer to Table 4 1 The currently selected aspect ratio is indicated by a XI to its left in this example 16 9 is selected Note that some aspect ratios are unavailable and or not useful with certain types of source material The optimal setting depends on a number of factors such as e The aspect ratio of the source material as broadcast or encoded on the playback medium e The display type 16 9 or 4 3 and output resolution settings at the source component Most modern DVD BD players and set top boxes have such controls e Viewer preference original aspect ratio with black bars or a full screen presentation with some distortion or cropping A Note
101. p menu and set it to Power Then select Power from the Lamp menu to set the lamp power level You can choose to run the lamp as bright as possible this is the default setting or you can choose a lower setting Generally lower lamp output prolongs the life of the lamp but decreases brightness Intensity To maintain a constant brightness level select Mode from the Lamp menu and set it to Intensity Then select Intensity from the Lamp menu to specify the desired brightness level The projector automatically adjusts the amount of power applied to the lamp as needed to maintain the desired brightness level 1 The Intensity Lamp Mode setting cannot be used with the RVR A Note control refer to RVR on page 68 2 The Intensity value is not the actual lumen output but rather a correlated value only 1246 may represent 3500 lumens for example e Color Temp Select Color Temp from the Display Color menu to adjust the color temperature Color temperature establishes the color of gray by adjusting the 75 white point to various color points What are color points A color point is an x y coordinate pair that defines a color s location on the standard CIE chromaticity graph shown in Figure 4 7 CIE stands for Commission Internationale de I Eclairage International Commission on Illumination the organization responsible for color measurement and management standards 66 Signature Cinema SC 50d SC 60
102. p the projector away from heating and or air conditioning vents Changes in temperature may cause drifts in the projector circuitry which may affect performance Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers Common sources of these include slide projectors speakers power amplifiers and elevators 24 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation The projection lens is shipped separately from the projector Proceed as follows to install 3 4 it Installing the Primary 1 Remove the lens plug from the lens opening in the projector Projection Lens Never operate this projector without a lens The lens seals the A WARNING projector preventing contaminants from entering the interior of the projector 2 Remove the rear cap from the lens Keep the front lens cap on the projection lens to protect it from damage during the installation process 3 Rotate the lens clamp to the OPEN position CLAMP OPEN CLAMP CLOSED bh SECURITY SECURITY SCREW 4 Remove and retain the two security screws from the lens mount Security Screws 5 Align the lens interface plate with the lens mount Align the lens electrical connector with the mating connector on the lens mount Fully insert the assembly straight into the lens mount opening without turning Press using your hand When installing the lens ensure that it i
103. pment e Turn off all equipment before making any connections e Use the correct signal cables for each source e For best performance and to minimize cable clutter use high quality cables that are only as long as necessary to connect two devices Don t use a 20 foot cable when a 6 foot cable will suffice e Ensure that the cables are securely connected Tighten the thumbscrews on connectors that have them Digital Video Connection Connect the HDMI Out To Display connector on the DHD Controller to the DVI I input in Slot 2 of the SC 50d SC 60d as shown in Figure 3 9 ian ill RJ 11 RS 232 to DB 9 Communication Adapter Cable provided provided 1 1 o I IL 7 T T I IL TA T T G IZ T IT T 2 y TC OY i TAT DVEIto HDMI E T T dapter Ono IT IL I d ewm IT I I i LIC xim p ovided ni ILE II II Y KE LI I YAMI TT NK II Y III Nay TT I IL TL ITT T INS w TT IL T M NITW a NY I I 1IL ITTIW WT IL o o HDMI Cable 2 not provided D m jj Display y Control owm HDMI Out To Display Figure 3 9 Connecting the SC 50d SC
104. quency o rao e E 555 Rate Hz MHz 53555 o lt 000 kHz oo o 222 II aan 3 o II 5 o EEE ooo o ooo PAL M 59 94 60 00 15 734 15 750 3 580 y PAL N 50 00 15 625 3 580 y SECAM 50 00 15 625 13 500 y y 106 Signature Cinema SC 50d SC 60d Installation Operation Manual 020 1105 00 Rev A March 2011 Runco International e 800 23RUNCO e Fax 503 748 8161 e www runco com
105. rerssnssacetvsnsvaceiesusnacaresssusaacvsenssdiesasdaccrsdedansacervessad 85 Serial COMMUNICATIONS mai a deberi edel AD FF FFO Gen 85 RS 232 Connection and Port Configuration se e 85 Serial Command Syntax sse nennen eene 85 Using Discrete IE Codes cesset t RR eb ER bie PR Els 90 IR Command Protocol ice uec ea onal inven Le e uc WS d 90 IR Command Listas lila t e orte eee b LY 92 Using HDMI CEG MeSSAg6S eit d eite tette satay epe netu e ttp o erp Eran e EE ERN 94 CEC Command Lista ese ee ie ete ee retenta tete 94 Ta Specifications ee erede Lou ny nnr dai adena nnn aaneen anaia veeususuecdcsmeveersien 97 SC 50d SC 60d Projector Specifications sssessseee 97 DHD Controller Specification iin emere 99 o G 50d 59 60d DIMENSIONS id ado 101 SC 50d SC 60d Dimensions with CineWide with AutoScope Assembly 102 Supported TIMO Stat ete on e t rp DL DO te E ER eO 103 Signature Cinema SC 50d SC 60d Installation Operation Manual Xii Table of Contents Notes xiv Signature Cinema SC 50d SC 60d Installation Operation Manual List of Figures 2 1 SC 50d SC 60d Top Rear Front View esses eene nnne 5 2 2 90 508 SG 60d Input Panel mili etd eret dp Mere rep tag it 6 2 3 DHD Controller Front Panel rai ion nter pr ERR OR E RP ERR anm 8 2 4 DHD Controller Rear Panel senem en nennen enmt nnne 9 2 5 D
106. respect to the projector this is normal Once the proper lens angle has been set firmly tighten the Pitch Adjustment T Screws to secure the lens in place There may be some pincushion distortion even after the lens is A Note properly adjusted especially at shorter throw distances If this is the case Runco recommends that you slightly over scan the image into the screen frame area to mask the distortion 48 Signature Cinema SC 50d SC 60d Installation Operation Manual Installation Yaw Adjust Loosen the Yaw X Adjustment Levers to allow the lens to pivot freely from side to side Then angle the lens to even out any left to right pincushion distortion Anamorphic Lens Top View Correct Position Wrong Position Once the proper lens angle has been set firmly tighten the Yaw X Adjustment Levers to secure the lens in place Geometry 1 Input an anamorphic cross hatch test pattern to the DHD Controller 2 Unscrew the Anamorphic Lens just enough to allow it to rotate freely 3 Grasp the lens by the center ring and rotate the lens until the image is properly anamorphic J j j j 4 EJ Wrong Position Correct Position 4 When the image geometry appears correct tighten the Anamorphic Lens Set Screw item 10 to secure the lens in place When viewed from the front the rear opening on the anamorphic le
107. rom Runco Specifications are subject to change without notice 100 Signature Cinema SC 50d SC 60d Installation Operation Manual Specifications Figure 7 1 shows the SC 50d SC 60d dimensions 7 3 SC 50d SC 60d 3 Dimensions o 3 on om o35 59 03 5U x 3 207 O 9 o0 23 O o 2 2929 fe 23 soe o Tw 33 8in T 9 o 857 6mm as m 2 ox L X E 9 e 3 a m o f rH cL rH lt gt cD X 5 4in 137 6mm 11 7in 296 4mm a 8 S Pur lt ose 2 3 ES deg u 003 o EX d o TES SAN oo o lt o 0353 3 o a go jor 3 m No og9 9 99 3 3 32 o gt p aS o gt o 9 o o fe a a 2 a 24 0in 610mm Figure 7 1 SC 50d SC 60d Dimensions Signature Cinema SC 50d SC 60d Installation Operation Manual 101 Specifications 7 4 Figure 7 2 shows the SC 50d SC 60d dimensions with the optional CineWide with SC 50d SC 60d AutoScope assembly Dimensions with CineWide with 3 0in AutoScope Assembly 76 4mm Al Foot height 2 6in 67 2mm _ Auto cope i AutoScope height j AutoScope A E OUT 5 68in 173 7mm Lens angle height and distance h MEL from projector
108. s NATIVE Displays the source signal in its native resolution centered in the display area 16 9 For viewing 16 9 DVDs or HDTV programs in their native aspect ratio 4 3 Scales the input signal to fit 4 3 display mode in the center of the screen LETBOX Letterbox For viewing non anamorphic full screen DVDs on a 16 9 screen V WIDE VirtualWide Enlarges a 4 3 image horizontally in a non linear fashion to fit 16 9 full screen display CINEMA For viewing 2 35 1 source material V CINE Selects the Virtual Cinema aspect ratio used for viewing 16 9 source material on a 2 35 1 screen Signature Cinema SC 50d SC 60d Installation Operation Manual 13 Controls and Functions Setup Remote Control x The setup remote control unit furnished with the SC 50d SC 60d gives you access to the motorized lens controls position focus and zoom Figure 2 6 shows the setup remote control and the paragraphs that follow describe its functionality y a f A e Con dis MAN e inie mehi E ar tog df E SAS lada SEDD E O Figure 2 6 Setup Remote Control for SC 50d SC 60d e FOCUS Button Press to access the lens focus controls e ZOOM Button Press to access the lens zoom controls e LENSS Button Press to access the lens shift controls e MAIN Button Press to return to the Main lens control menu from the FOCUS ZOOM or LENSS lens shift page 14 Signature Cin
109. s so the above limitations and exclusions may not apply to you COPYRIGHT AND TRADEMARKS Copyright 2011 Runco International LLC Runco This document contains proprietary information protected by copyright trademark and other intellectual property laws All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of Runco The trademarks reproduced in this Runco Owner s Manual and used on the Runco Products are either owned by Runco or are licensed by Runco You may not reproduce or use the trademarks without the prior written consent of Runco Runco Products are manufactured under one or more of the following patents US Patent 6755540 and Other Patents Pending vi Signature Cinema SC 50d SC 60d Installation Operation Manual Important Safety Instructions Thank you for your purchase of this quality Runco video product For the best performance please read this manual carefully as it is your guide through the menus and operation WARNING CAUTION This symbol is intended to alert the user to the presence of AN A N uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric CAUTION shock TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK HE SUSE SER UICEABLE DARTSUNSIDE This symbol is intended to alert the user to the prese
110. s not inserted at an angle as A Note this can cause damage 6 While holding the lens flat against the lens mount rotate the lens clamp clockwise to lock the lens assembly in place 7 Re attach the lens mount security screws that you removed in Step 4 8 Remove the front lens cap Signature Cinema SC 50d SC 60d Installation Operation Manual 25 Installation 3 5 If you are installing a standard SC 50d SC 60d without an anamorphic lens skip this Installing the Optional step and proceed with Mounting the SC 50d SC 60d page 27 CineWide with If you are installing an SC 50d CineWide with AutoScope or SC 60d CineWide with AutoScope Lens Motor _ AutoScope proceed as follows to install the lens mount motor assembly motor You will install the CineWide lens after you install the 1 Do not install the CineWide lens yet only the AutoScope lens A Note projector and adjust the primary lens 2 Some components shipped with your projector may differ slightly from what is shown in these instructions 3 The anamorphic lens mounting kit is partially pre assembled at the factory the AutoScope lens motor and lens mounting assemblies are both fully assembled Remove Projector Front Place the projector upside down on a blanket or other soft surface Loosen and remove Feet the two front feet on the projector Install Anamorphic Lens y Line up the eight mounting holes on the lens motor housing with those on the bottom of Motor
111. s or projector is used in this example Figure 3 4 Horizontal Lens Shift EXAMPLE ONLY 20 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 3 4 lists the lens shift limits for each available SC 50d SC 60d lens as percentages and absolute measurements with a 120 x 67 5 inch 1 78 1 screen Table 3 4 Vertical and Horizontal Lens Shift Limits Lens Option Athena Dos Athena Tres Athena Quatro Athena Cinco Athena Uno Lens Shift Limits as Percentages of Screen Height or Width Note 1 Vertical Up 17 60 Note 2 Down 17 60 Left 6 25 Horizontal Right 6 25 Lens Shift Limits in Inches with a 120 by 67 5 inch 1 78 1 Screen Up 11 48 40 50 Vertical Down 11 48 40 50 Left 7 20 30 00 Horizontal Right 7 20 30 00 Notes 1 Vertical shift limits are percentages of the screen height Horizontal shift limits are percentages of the screen width 2 Vertical lens shift figures are for ceiling mount configurations For floor installations where the projector is upright reverse the up down vertical lens shift percentages Signature Cinema SC 50d SC 60d Installation Operation Manual 21 Installation Installation Folded Optics In rear screen applications where space behind the projector is limited a mirror may be used to fold the optical path as shown in Figure 3 5 The position of the projector and mirror must be accurately set If you are co
112. screen 16 9 Image on 2 35 1 Screen with Virtual Cinema Native NATIVE Select Native to display the source signal in its native resolution centered in the display area with no re sizing or overscan This means for example that 720p HDTV programs will display with unused pixels on all sides 320 on the left and right sides and 180 above and below With SDTV and EDTV sources the DHD Controller scales the image horizontally to achieve a 16 9 aspect ratio Signature Cinema SC 50d SC 60d Installation Operation Manual 55 Operation Operation Picture Picture Contrast Color Tint Sharpness Noise Filter Use the controls in the Picture Menu to calibrate each DHD Controller input to achieve optimum picture quality The DHD Controller has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation ISF The ISF has developed carefully crafted industry recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices Accordingly Runco recommends that setup and calibration be performed by an ISF certified installation technician All signal types require separate processing Therefore you need to calibrate each DHD Controller inout separately When you change a picture quality setting save the chang
113. set ALL controller settings including image settings back to their factory defaults choose System Reset from the Service menu A confirmation message appears Select Yes to continue with the reset or select No to cancel perform a System Reset save your Custom Memory Presets page 62 and ISF Day Night Memory Presets page 68 This action is not undoable Proceed with caution Before you A Caution Signature Cinema SC 50d SC 60d Installation Operation Manual 79 Operation Notes 80 Signature Cinema SC 50d SC 60d Installation Operation Manual Maintenance and Troubleshooting 5 Maintenance and Troubleshooting The lamp should be replaced when it reaches the end of its life typically 2 000 hours or 5 1 sooner if a noticeable degradation in brightness occurs Lamp Replacement Keep track of the number of hours the lamp has been in use and be aware of any changes to brightness These indicators will help you effectively maintain operation of the projector To find out how long the currently installed lamp has been in service select Lamp Info from the Display Device Configure menu available by selecting Service gt Display Device gt Configure gt Lamp Info in sequence For lamp or filter replacement please contact your nearest Runco authorized service center or Runco dealer Do not attempt to replace the lamp yourself 1 Turn off the projector and unplug the power cord Allow the projector t
114. sk from the IP Configuration menu to manually configure the IP subnet mask The procedure is similar to that for setting the IP address Default Gateway Select Default Gateway from the IP Configuration menu to manually configure the default IP gateway The procedure is similar to that for setting the IP address e Communication Test Select Communication Test from the IP Configuration menu to verify proper operation of the network communication link To start the test select Start Test from the Communication Test menu The DHD Controller displays the message Performing Communication Test When the test completes the DHD Controller displays either Failed along with the error that occurred or Succeeded Auto Firmware Upgrade Select Auto Firmware Upgrade from the Network menu to enable automatic detection of a newer version of the DHD Controller firmware If one is found you can configure the DHD Controller to install it automatically These features make it easier to keep your DHD Controller firmware up to date e Auto Check For New Firmware To have the DHD Controller automatically check for firmware updates at periodic intervals select Auto Check for New Firmware from the Auto Firmware Upgrade menu and set it to On If you prefer to do this manually set it to Off and use the Check For New Firmware sub menu described below e Auto Perform Upgrade If the Auto Check For New Firmware process determines that
115. t 2 Press ENTER 3 Press A or W repeatedly to set the highlighted character 4 Press or lt to select the next or previous character Use the A and W buttons to change it 5 Press ENTER when you have finished editing that line of text 6 Repeat Steps 1 through 5 for each line of text you want to edit 7 Press MENU when you have finished entering customer information E Mail Calibration Data To have the DHD Controller collect all calibration data attach it to a message and send it to the destination e mail address select E Mail Calibration Data from the E Mail Notification menu To confirm this action select Yes and press ENTER To cancel and return to the previous menu select No 74 Signature Cinema SC 50d SC 60d Installation Operation Manual Operation e Remote Network Control Select Remote Network Control from the Network menu to enable or disable control of the DHD Controller via an IP connection typically using a web browser Set it to On to allow all incoming remote network connectivity Set it to Off to disable any incoming network communication that was not initiated by the DHD Controller This setting has no effect on the E Mail Notification or Auto A Note Firmware Upgrade functions Display Device Auto Calibration Auto Calibration is a process in which the projector quickly optimizes critical display parameters such as size position and pixel tracking based on the type of incoming video si
116. t o Figure 3 19 External IR Receiver Connection Signature Cinema SC 50d SC 60d Installation Operation Manual 39 Installation Connecting to AC Power Ethernet Network Connection Use a standard Category 5 network cable with an RJ 45 plug to connect a network hub router or gateway to the Ethernet port on the DHD Controller see Figure 3 20 For more information about configuring and using this connection refer to Network on page 71 Display Control TTTTTT to Ethernet Hub Router or Gateway 1 Transmit Data 2 Transmit Data 3 Receive Data 6 Receive Data Figure 3 20 Ethernet Network Connection to DHD Controller Projector and DHD Controller The SC 50d SC 60d ships with two 2 AC power cords one for the DHD Controller and one for the projector They are not interchangeable The projector power cord is rated at 15 amps and has a ferrite sleeve to reduce radio frequency interference RFI emissions to a level that conforms to FCC regulations AC power cord Pn sleeve ex To power outlet To Projector AC IN Plug the female end of the projector power cord into the AC receptacle on the rear of the SC 50d SC 60d AC 100V 240V see Figure 2 2 Then connect the other end to your AC power source Use ONLY the AC power cord
117. t sub pixels and d the Runco model size If sub pixels have been identified as unacceptable by Runco the LCD will be deemed faulty and will be replaced if reported within the warranty period If there are issues with bright or dark sub pixels gather the information listed above and call or email support runco com Other Terms and Conditions y Runco will not accept returned Product unless an RMA number has been issued by Runco NS If an Advance Exchange return occurs it is the customer s responsibility to properly package the defective product and ship it to the address provided by the Runco technical support representative with the RMA number prominently displayed If the defective product is not properly packaged and is damaged in transit during its return to Runco you may be invoiced for either the repair costs if repairable or the MSRP of a replacement product and shipping costs incurred by Runco o The repaired or replaced product will assume the remainder of your original product s RuncoCare Service Plan term or 90 days from the date the repaired unit is shipped whichever is longer If a replacement product is sent the customer agrees to retain the replacement for the product you purchased and your defective product becomes the property of Runco Extended Service Options Runco offers extended and expanded service plans For information on additional product protection please email serviceorders runco com or call tol
118. te and memory preset onto a clipboard which is a temporary memory location When you do the message Settings Copied briefly appears on screen The Copy Paste menu then re appears indicating the source of the copied settings Not Copied settings are not retained after a power cycle A ote e Paste Settings To apply the settings on the clipboard to a different input source signal format and or memory preset do any or all of the following e Switch to another input for example from HD1 to HD2 e Change the output signal format at the source for example from 720p 60 to 1080i 60 e Switch to another Memory Preset for example from ISF Night to Custom 1 Then select Paste Settings from the Copy Paste menu If you want to keep these new settings you must save them Refer to Save ISF Night Save ISF Day on page 68 or Memory Presets on page 62 Output Shift The controls in the Output Shift menu are similar to those in the Input Position menu except that they change the characteristics of the output signal These settings are saved independently for each aspect ratio Image Alignment Use the controls in the Image Alignment menu to ensure proper image geometry that is a perfectly rectangular projected image with no keystoning or pincushion For detailed instructions refer to Adjusting the Image Geometry on page 43 Splash Configure Use the Splash Configure menu to control the appearance and behavior
119. tent across the screen that aspect ratio is maintained and that pixel phase see above can be optimized For each input the DHD Controller lets you save image quality settings as presets that you can recall at a later time You can create up to four presets per input and display mode resolution and frame rate The DHD Controller stores the following display modes in each memory preset e 480i e 480p e 576i e 576p e 720p 24 Hz e 720p 25 Hz e 720p 30 Hz e 720p 50 Hz e 720p 60 Hz e 1080i 50 Hz e 1080i 50 Hz Australia e 1080i 60 Hz e 1080p 24 Hz e 1080p 25 Hz e 1080p 30 Hz e 1080p 50 Hz e 1080p 60 Hz Use the Memory Presets menu to recall saved image presets or to save image settings in the Custom 1 or Custom 2 memory location The currently selected preset is indicated by a 3 to its left in the example shown here ISF Night is selected 62 Signature Cinema SC 50d SC 60d Installation Operation Manual You should save changes to any of the following settings to a preset otherwise they will be lost when a new input source or resolution is selected To select a memory preset press A or W to highlight it and press ENTER To save the settings for the current input and display mode to the Custom 1 or Custom 2 memory preset select it press lt or gt to highlight Save and press ENTER A Note To reset the Custom 1 or Custom 2 memory preset to its factory default state sel
120. tion Issues sssssssseeee LL FFF F Yno 23 MEMO EET 24 Other Considerations sce ene e et d ete be een iens 24 Installing the Primary Projection Lens sssssseseee eene 25 Installing the Optional CineWide with AutoScope Lens Motor sssee 26 Remove Projector Front Feet ee rtt re rec te dee de doe ne Pee aa 26 Install Anamorphic bens Motor 4 eot ig ttem ee YDY EE RR EHE AA 26 Mounting the SC 50d SC 60d oo ei rr ti emen eene enne nenne 27 Floor Mounting Upright rr ERE EORR RR REN TAMIS 27 Ceiling Mounting Imverted cue teet ete er YDY e e 27 Installing the Projector in an Enclosure eee ieee etter LL RF LL RR RL DL RYAN 27 Adjusting the Projection Angle ees irria era eela a meme 28 Connections to the SC 50d SC 60d and DHD Controller 0 eee 29 Connecting the DHD Controller to the SC 50d SC 60d sse 29 Connecting Source Components to the DHD Controller esssssssss 31 Connecting an Audio Processor or Secondary Display Device tothe DHD Gontroller Optional ia tiiis tenn id 36 Additional Connections to the DHD Controller Optional 37 COMMECTINGTOACPOWES a sec terit dte ea ee ie Ne e Lathe BRAF ee 40 TUNDO one FONET sod Gaede p erede datae dedans darts 41 Primary Lens Adjustments Focus Zoom and Position sse 41 Adjustingithe Picture Orientation 1 3 htc tet epe e t eter bebe des 42 Adjusting the Image Geometry srira ra ta emere 43 Installing
121. tive input SCART NA YES Selects the SCART input 86 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 6 1 Serial Commands continued Command Parameter Value Description min max Stored Aspect Ratio Commands 16 9 NA YES Selects the 16 9 aspect ratio 4 3 NA YES Selects the 4 3 aspect ratio ASPECT NA NA Returns current aspect ratio CINEMA NA YES Selects the Cinema aspect ratio LETTERBOX NA YES Selects the Letterbox aspect ratio NATIVE NA YE Selects the Native aspect ratio VIRTUALWIDE NA YES Selects the VirtualWide aspect ratio VIRTUALCINEMA NA YES Selects the Virtual Cinema aspect ratio Picture Adjust Commands BRIGHTNESS 50 50 YES Sets a value for brightness BRIGHTNESS NA NA Returns brightness setting value CHROMADELAY 7 7 YES Sets a value for input color chroma delay CHROMADELAY NA NA Returns input color chroma delay setting COLOR 50 50 YES Sets a value for color COLOR NA NA Returns color setting value CONTRAST 50 50 YES Sets a value for contrast CONTRAST NA NA Returns contrast setting value FILMMODE 0 1 YE Sets Film Mode off 0 or on 1 FILMMODE NA NA Returns Film Mode setting 0 off 1 on FILTER 0 10 YE Sets a value for input color noise filter FILTER NA NA Returns input color noise filter setting PHASE 0 31 YES Adjusts phase PHASE NA NA Returns phase setting value SHAR
122. ts only Input Position Sersan vods Input Color Chroma Delay 052 7 Zoom Crop Composite inputs only Phase Noise Filter 0 1 2 63 i S ISF Night RGB Component SCAHT signals only ave ig Back Confirm Tracking Save ISF Day RGB Component SCAHT signals only Copy Settings Copy Paste Recall ISF Night or ISF Day Paste Settings Memory Recall Save Custom 1 or Custom 2 Left Right 50 49 0 49 50 Presets Reset Custom 1 and Custom 2 to Factory Up Down dE i Default Output Shift Width Sleep Timer Off 90 Minutes 60 Minutes 90 Minutes 2 Height 50 49 48 0 Hours or 4 Hours Image Corner Alignment Top Left Top Right Bottom Left Bottom Right ae Center Top Middle Left Middle Right Middle Alignment Midpoint Alignment Bottom Middle Owner Name Soi ISF Calibrated plash ISF Other Configure Splash Timer 5 6 7 15 59 60 Note Default settings appear in bold type Splash Enable On Off OSD Position Hor Ver 0 1 2 100 Figure 4 1 SC 50d SC 60d OSD Menu Structure Signature Cinema SC 50d SC 60d Installation Operation Manual 51 Operation Service Color Bars 1 Color Bars 2 Test Video Focus Grey Bars Input Names Rename Restore Picture Orientation Auto Floor Front Ceiling Front Floor Rear or Ceiling Rear Y Lamp Info A 1 Display Device Configure read only Projector Serial Number 7 White Red Green Blue Yellow Cyan Diagnost
123. tup Guide Optional Accessories CineWide with AutoScope system secondary anamorphic lens and motorized mount Ceiling mount kit part number 956 0302 00 4 Signature Cinema SC 50d SC 60d Installation Operation Manual Controls and Functions 2 Controls and Functions Figure 2 1 shows the key SC 50d SC 60d components 2 1 SC 50d SC 60d at a Glance D Figure 2 1 SC 50d SC 60d Top Rear Front View Signature Cinema SC 50d SC 60d Installation Operation Manual 5 Controls and Functions 2 2 SC 50d SC 60d Input Panel RIGHT INTAKE SIDE PANEL The right side panel is perforated to allow cool air to enter the projector LEFT EXHAUST SIDE PANEL The left side panel is perforated to allow warm air to exit the projector Removing this panel provides access to the lamp INPUT PANEL COVER Removing this panel provides access to the projector input panel For more information refer to SC 50d SC 60d Input Panel on page 6 REAR EXHAUST VENT Warm air exits the projector through this vent Ensure that it is not obstructed in any way ADJUSTABLE FEET 4 Located on the underside of the projector are four adjustable feet Raise or lower these feet when positioning the projector to ensure it is level on all sides so the displayed image will appear rectangular without any keystone PROJECTION LENS
124. turns software version number SYSSTATE 0 4 NA Returns current system state O Off 1 Initializing 2 On 3 Powering Down 4 Error TRIGGER 1 3 YES Assigns trigger to currently selected aspect ratio The following serial commands are meant to emulate buttons on the remote control or DHD Con troller front panel Each button has its own serial command so effectively it is as if you were using the IR remote only you ll be doing so via serial commands These commands provide active OSD responses just like the IR remote DOWN NA NA Down Arrow W key ENTER NA NA ENTER key EXIT NA NA EXIT key LEFT NA NA Left Arrow lt q key MENU NA NA MENU Signature Cinema SC 50d SC 60d Installation Operation Manual 89 External Control External Control 6 2 Using Discrete IR Codes IR Command Protocol x Table 6 1 Serial Commands continued Command Parameter Value Description min max Stored p RIGHT NA NA Right Arrow p gt key UP NA NA Up Arrow A key The DHD Controller accepts commands in the form of IR signals that conform to the Phillips RC5 protocol Each DHD Controller remote control button has an RC5 control code associated with it You can use these codes to program a third party universal remote control unit to work with the DHD Controller These third party products usually come with a computer software application for this purpose For more information consult the documentation provi
125. tus during lightning storms or when unused for long periods of time 4 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 The 12V trigger only outputs 12Vdc signal for triggering Do not connect to any other power input or output This could cause damage to this unit 6 Keep the packing material in case the equipment should ever need to be shipped 7 The lamp becomes extremely hot during operation Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement 18 Do not operate lamps beyond the rated lamp life Excessive operation of lamps beyond rated life could cause them to explode in rare occasions 19 Never look directly into the lens when the lamp is on Signature Cinema SC 50d SC 60d Installation Operation Manual vii Compliance Information DECLARATION OF CONFORMITY Manufacturer s Name Runco International LLC Manufacturer s Address 1195 NW Compton Drive Beaverton OR 97006 1992 hereby declares that the Products Model Numbers SC 50d SC 50d CineWide with AutoScope SC 60d and SC 60d CineWide with AutoScope conform with the provisions of Council Directive 2004
126. ures and Benefits Introduction Key Features and Benefits Parts List The SC 50d SC 60d offers these key features and benefits Cinema quality color with the most accurate and exceptionally broad color gamuts Multiple lens options including compatibility with Runco s award winning CineWide with AutoScope Ships with Runco s DHD Controller featuring ViVix video processing for exceptional scaling analog to digital signal conversion and control via IR or RS 232 Bundled with two years of Runco PremierCare service program providing on site calibration and two years of ongoing support from Runco Native Resolution 1920 x 1080 16 9 Native Aspect Ratio DLP system using three high performance Digital Micromirror Device DMD chips Your SC 50d SC 60d is shipped with the following items If any items are missing or damaged please contact your Runco dealer or Runco Customer Service at 800 23RUNCO Signature Cinema Series SC 50d SC 60d Private Cinema Projector and DHD Controller DHD Controller Remote Control Unit and batteries Setup Remote Control Unit and batteries AC power cord for projector with ferrite sleeve rated at 15 amps AC power cord for DHD Controller RJ 11 Telephone Cable 50 feet 15 24 meters Serial Port Adapter RJ 11 Female to DB 9 Male Adapter DVI I male to HDMI female Rack mounting brackets and hardware for the DHD Controller Signature Cinema SC 50d SC 60d Quick Se
127. urn on again when the cover is closed A ote 7 Re attach the Left Exhaust Side Panel to the projector 82 Signature Cinema SC 50d SC 60d Installation Operation Manual Table 5 1 provides some general guidelines for troubleshooting problems you may encounter with the SC 50d SC 60d If the suggested solutions fail to resolve the problem or if you encounter an issue not described here please contact Runco Technical Support Table 5 1 Troubleshooting Chart Symptom The projector does not turn on The projector and DHD Controller are both on but there is no picture and on screen menus do not appear The display is on and menus appear but there is no picture A projected image from a DVD is split or otherwise scrambled Image geometry is incorrect Possible Cause s e The SC 50d SC 60d is not plugged in and switched on or the AC outlet is not active e The DHD Controller is not plugged in and switched on or the AC outlet is not active e The remote control batteries have run out e The serial connection from the DHD Controller to the SC 50d SC 60d is incorrect e Lens cover is on or shutter is closed e Lamp failed to ignite e Faulty or incorrect video connection between the DHD Controller and the SC 50d SC 60d e ncorrect source selection e Source component is not turned on Source component is connected incorrectly or not at all e DVD player is connected t
128. washed out and or dark areas appear too bright Colors in the image are swapped for example reds appear blue or vice versa The display freezes suddenly The projector will not turn back on after it was powered down or the image disap pears during operation AutoScope lens motor does not work Possible Cause s Solution e Poor quality or improperly e Ensure that the source is connected source properly connected and of adequate quality for detection e The horizontal or vertical e Correct at the source scan frequency of the input signal may be out of range for the projector e Contrast is set too high e Lower the contrast setting e Brightness is set too high e Lower the brightness setting e The Red Pr Green Y or e Ensure that the source Blue Pb outputs from the outputs are connected to source are connected to the correct DHD Controller the wrong inputs on the input DHD Controller e Excessive voltage noise on e Power down the projector the AC or ground input has and disconnect from AC interrupted the projector s Then plug in again and ability to lock on toa power up as usual signal e The projector will not turn e Wait until the LED at the on for two minutes after front of the DHD Controller power down to protect turns red the lamp e The lamp has failed e Replace the lamp e The motor is not plugged e Ensure that the motor is in or the AC outlet is not plugged in and t
129. y and focus DHD Controller input calibration adjust the following for each 53 through 68 DHD Controller input and display mode resolution frame rate save settings when finished 14 Aspect ratio Color level Brightness e Tint Contrast Input position Color temperature and white balance 16 Signature Cinema SC 50d SC 60d Installation Operation Manual Proper installation of your projector will ensure the quality of your display Whether you are installing a projector temporarily or permanently you should take the following into account to ensure your projector performs optimally Choose the installation type that best suits your needs front or rear screen floor mount or inverted mount Table 3 2 compares these various installation methods Table 3 2 Projector Installation Options Advantages Considerations Front Screen Floor Mount Installation e Easy to set up e Shares floor space with audience Can be moved or changed quickly e Easy to access Front Screen Inverted Mount ceiling Installation e Installation is more permanent e Projector access is more difficult Does not take up audience space e Projector is unobtrusive Projector cannot be accidentally moved Rear Screen Floor Mount Installation e Requires separate room e Installation cost is usually higher Projector is completely hidden Projector is easily accessed Usually good ambient light rejection
130. ystem Reset Use the Service menu to access advanced projector configuration settings This menu should be used by ISF certified technicians only Not You must enter a passcode to access the Service menu ote Test Video Select Test Video from the Service Menu to access the internal test patterns on the DHD Controller Table 4 3 lists the available test patterns and describes their suggested usage Table 4 3 Test Patterns and Their Suggested Usage Pattern Color Bars 1 Suggested Usage Use this pattern when making color saturation and tint adjustments Color Bars 2 Use this pattern when making color saturation and tint adjustments Use this pattern when adjusting the focus Focus Use this pattern when making brightness contrast or white balance gain offset adjustments Grey Bars AEL Press MENU to exit test pattern mode 70 Signature Cinema SC 50d SC 60d Installation Operation Manual Input Names You can give each input a descriptive name For example you may want to change the default input name to the type of source component connected to it VCR DVD Laptop et cetera Input names can be up to 12 characters long To edit an input name select Input Names from the Service menu Press A or W to select an input and press ENTER Use the A or W buttons to change a character press lt q or to select a character to change When you hav

Runco SC-50D User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents