Rosewill RC205 User's Manual
Contents
1. After the Serial ATA PCI Host Adapter and attached drives are configured boot up Windows 2 At the Add New Hardware Wizard check Specify the location of the driver advanced and click Next 3 Insert the Driver diskette check Specify a location uncheck the other boxes type in AA and click Next 4 Click Next and then Finish 5 Remove the Driver diskette and restart Windows to complete driver installation Verification of the Proper Installation for Windows 98 98SE ME 1 Double click My Computer Control Panel System Click Device Manager tab 2 Double click SCSI Controllers Silicon Image Sil 3112 Serial ATA Controller should be listed 3 Highlight Silicon Image Sil 3112 Serial ATA Controller and click Properties A message This device is working properly is displayed in the dialog box the driver has been correctly installed If any error message is displayed remove Silicon Image Sil 3112 Serial ATA Controller and restart your system 2 3 Windows NT 4 0 Driver Installation For New Windows NT 4 0 System 1 After the Serial ATA PCI Host Adapter and attached drives are configured follow Microsoft procedures to install Windows accordingly 2 At the Windows Set up screen press F6 to specify and add the driver 3 Press S select Other then press Enter 4 Insert the Driver diskette and press Enter 5 Select Silicon Image Sil 3112 Serial ATA Controller Driver and press Enter 6 Press Enter to continue and follow on scree2. Windows Millennium Windows NT 4 0 Windows 2000 and XP 1 1 Features 1 1 1 PCI Interface e Compliant with PCI Specification revision 2 2 e Integrated PCI DMA engines e 32 bit 33 66MHz fully compliant PCI host interface 1 1 2 High Speed Serial ATA Interface e Dual high speed Serial ATA interface Channels each supporting SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual 1st generation Serial ATA data rates 1 5Gb s e Fully compliant with Serial ATA 1 0 specifications e Supports Spread Spectrum in receiver e Independent 256 byte FIFOs 32 bit 64 deep per Serial ATA channel for host reads and writes 1 1 3 The Individual features for different Models 1 1 3 1 Model A Serial ATA Internal 2 Ports e Supports Independent two Internal Ports 1 1 3 2 Model B External 1 Port Internal 1 Port e Supports one External Port and one Internal Port e One Special Shell SATA connector on External Port to support Mobile HDD Mobile CD ROM Mobile DVD and Mobile CD RW 1 1 3 3 Model C Internal 1 Port External 1 Port Bracket Power e Independent one Internal SATA Ports e One External Port and one Internal Port sharing one SATA Channel e One Special Shell SATA connector on External Port to support Mobile HDD Mobile CD ROM Mobile DVD and Mobile CD RW e One USB like Connector on board to provide 2A 5V DC power output for Mobile Storage Devices using 1 1 3 4 Model D External 2 Ports Bracket Power e Independent
3. the Serial ATA PCI Host Adapter and attached drives are configured boot up Windows 2 Atthe Found New Hardware Wizard click Next 3 Select Search for a suitable driver for my device recommended and click Next 4 Insert the Driver diskette into the floppy drive check Specify a location uncheck the other boxes click Next type in AM Click OK and then Next to continue 5 If the Digital Signature Not Found message appears click Yes Note If prompted for Windows 2000 CD ROM insert the CD and click OK Type in D I386 click OK and Finish assuming D is your CD ROM drive 6 Click Finish remove the Driver diskette and click Yes to restart Windows to complete driver installation 2 5 Windows XP Driver Installation For New Windows XP Systems 1 After the Serial ATA PCI Host Adapter and attached drives are configured follow Microsoft procedures to install Windows accordingly 2 At the Windows Set up screen press F6 in order to specify and add the driver 3 Insert the Driver diskette Press S then press Enter 4 Select Silicon Image Sil 3112 Serial ATA Controller Driver and press Enter 5 Press Enter to continue and follow on screen instructions to complete Windows XP installation Note When the Software Installation warning pops up click Yes And when the Hardware SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual Installation warning pops up click Yes again For Existing Windows XP in old ATA channel Syste
4. two External SATA Ports e Two Special Shell SATA connector on External Port to support Mobile HDD Mobile CD ROM Mobile DVD and Mobile CD RW e One USB like Connector on board to provide 2A 5V DC power output for Mobile Storage Devices using 1 2 Package Contents e Low Profile Serial ATA 2 Channel PCI Host Adapter e This Users Manual e Driver Diskette e Low Profile Size PCI Bracket Not supported on Model D 2 Software Installation This section provides the information on how to install the drivers of Low Profile Serial ATA 2 Port SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual PCI Host Adapter for the operating systems New amp Existing Windows 98 98 SE New amp Existing Windows ME New amp Existing Windows NT 4 0 New amp Existing Windows 2000 New amp Existing Windows XP 2 1 Windows 98 98SE Driver Installation For New Windows 98 98 SE Systems 1 After the Serial ATA PCI Host Adapter and attached drives are configured follow Microsoft procedures to install Windows accordingly 2 Once Windows has been installed double click My Computer Control Panel System then click Device Manager 3 Double click Other Devices then PCI RAID Controller 4 Click Driver tab then Update Driver 5 Insert the Driver diskette and click Next 6 Select Search for a better driver than the one option and click Next 7 Check Specify a location uncheck the other boxes type in A and click Next Click Next and th
5. Hiosewill SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual This Manual for the Models of 2 Channels SATA HBA Model A Low Profile Serial ATA Internal 2 Ports Model B Low Profile External 1 Port Internal 1 Port Model C Low Profile Internal 1 Port External 1 Port Bracket Power Model D External 2 Ports Bracket Power 1 Introduction The Low Profile Serial ATA 2 Channels PCI Host Adapter is a PCI to dual Serial ATA host controller board which can support Low profile PCI and regular size PCI both It provides a 32bit 33 66 MHz PCI interface on the host side and dual fully compliant Serial ATA ports on the device side to access SATA storage media such as hard disk drive ZIP drive CD ROM CD RW DVD ROM The board can be used to upgrade your desktop computer to have dual Serial ATA Channels It accepts host commands through the PCI bus processes them and transfers data between the host and Serial ATA devices The board should be connected to SATA target device and will take the data serialize it and output it for transmission over the SATA interface The board can control two independent Serial ATA channels Each channel has its own Serial ATA bus and will support one Serial ATA device The board supports a 32 bit 33 66 MHz PCI bus revision 2 2 and the Serial ATA Generation 1 transfer rate of 1 5 Gb s 150 MB s It comes completely with drivers for Windows 98
6. en Finish 8 Remove the Driver diskette and click Yes to restart Windows to complete driver installation For Existing Windows 98 98 SE Systems 1 After the Serial ATA PCI Host Adapter and attached drives are configured boot up Windows 2 At the Add New Hardware Wizard click Next 3 Select Search for the best driver for your device option and then click Next 4 Insert the Driver diskette check Specify a location uncheck the other boxes type in AA and click Next 5 Click Next and then Finish respectively 6 Remove the Driver diskette and restart Windows to complete driver installation 2 2 Windows ME Driver Installation For New Windows ME Systems 1 After the Serial ATA PCI Host Adapter and attached drives are configured follow Microsoft procedures to install Windows accordingly 2 Once Windows has been installed click My Computer then click Properties Click Device SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual Manager tab 3 Double click Other Devices then PCI RAID Controller 4 Click Driver tab then Update Driver 5 Insert the Driver diskette check Specify the location of the driver advanced and click Next 6 Select Search for the better driver option check Specify a location uncheck Removable Media type in A and click Next 7 Click Next and then Finish 8 Remove the Driver diskette and click Yes to restart Windows to complete driver installation For Existing Windows ME Systems 1
7. ms 1 After the Serial ATA PCI Host Adapter and attached drives are configured boot up Windows 2 At the Found New Hardware Wizard check Install from a list or specific location advanced then click Next 3 Insert the Driver diskette Check Include this location in the search uncheck the other box type in A and click Next 4 When a warning message pops up click Continue Anyway then click Finish 5 Remove the Driver diskette and restart Windows Verification of the Proper Installation for Windows 2000 XP 1 Double click My Computer Control Panel System 2 Click Hardware then click Device Manager 3 Double click SCSI and RAID Controllers then double click Silicon Image Sil 3112 Serial ATA Controller to display driver properties 4 A message This device is working properly is displayed in the dialog box the driver has been correctly installed Thank you for purchasing Rosewill Product Please register your product at www rosewill com for complete warranty information and future support for your product
8. n instructions to complete Windows NT 4 0 installation For Existing Windows NT 4 0 in old ATA channel System 1 After the Serial ATA PCI Host Adapter and attached drives are configured boot up Windows SATA 150 1 Int 1 Ext Port PCI Adapter RC205 User Manual Double click My Computer Control Panel SCSI Adapters then click the Drivers tab 2 Click Ada then Have Disk 3 Insert the Driver diskette into the floppy drive and type in AA then click OK 4 Highlight Silicon Image Sil 3112 Serial ATA Controller and click OK 5 Remove the Driver diskette and restart Windows Verification of the Proper Installation for Windows NT 4 0 1 Double click My Computer Control Panel SCSI Adapters 2 Highlight Silicon Image Sil 3112 Serial ATA Controller and click Properties This device is working properly is displayed in the dialog box the driver has been correctly installed 2 4 Windows 2000 Driver Installation For New Windows 2000 Systems 1 After the Serial ATA PCI Host Adapter and attached drives are configured follow Microsoft procedures to install Windows accordingly 2 At the Windows Set up screen press F6 to specify and add the driver 3 Insert the Driver diskette Press S then press Enter 4 Select Silicon Image Sil 3112 Serial ATA Controller Driver and press Enter 5 Press Enter to continue and follow on screen instructions to complete installation For Existing Windows 2000 in old ATA channel Systems 1 After
Download Pdf Manuals
Related Search