Rolls RM65 User's Manual
Contents
1. TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME P PWR 17 8 0 4 13 LEFT RIGHT EFFECTS RETURN MASTER VOLUME RM65 Professional Audio Mixer INTRODUCTION Thank you for your purchase of the Rolls RM65 6 x 4 stereo professional Audio Mixer This unit is a breakthrough in size performance for an audio mixer It s a full function 6 channel mixer in a single space 19 rack chassis It is intended for sound reinforcement studio choir and other applications where high channel to size ratio is desired It has 6 phantom power switches and input gain trims located on the rear panel This manual assumes the user has some familiarity with audio mixers If the features knobs or jacks seem unclear please contact the dealer for help INSPECTION 1 Unpack and inspect the RM65 box and package If obvious physical damage is noticed contact the carrier immediately to make a damage claim We suggest saving the shipping carton and packing materials for safely transporting the unit in the future 2 Please complete the Warranty Registration Card and return it to the factory TABLE OF CONTENTS 1 INTRODUCTION INSPECTION TABLE OF CONTENTS DESCRIPTION FRONT PANEL 2 FRONT PANEL Continued REAR PANEL 3 OPERATION 4 OPERATION Continued 5 SPECIFICATIONS 6 SCHEMATIC DESCRIPTION FRONT PANEL FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R FX SEND PAN2. 5 4 1 9 15 14 11 10 6 12 7 8 13 5 4 3 7 13 12 8 6 9 2 2 1 1 9 10 15 14 11 4 3 5 1 2 1 2 I 1 G 2 O 3 I 2 G 1 O 3 I 1 G 2 O 3 1 2 3 6 5 7 8 2 3 1 4 6 5 7 8 2 3 1 4 2 3 1 4 5 6 7 8 6 5 7 8 2 3 1 4 2 3 1 4 3 15 Rev SCHEMATIC 1 6 PAN Adjusts the amount of relative signal to the Right Left or both Main Out jacks FX SEND Controls the amount of signal post volume control that is sent for that channel to the FX Send jack MASTER CONTROLS FX RETURN Adjusts the amount of signal coming back into the FX Return jack MASTER VOLUME RIGHT LEFT Controls the amount of signal sent out the main Right and Left Output jacks and sets the overall signal level except for the Monitor Send jack REAR PANEL CHANNEL 1 MIC LINE TRIM CHANNEL 2 MIC LINE TRIM CHANNEL 3 MIC LINE TRIM CHANNEL 4 MIC LINE TRIM CHANNEL 5 MIC LINE TRIM CHANNEL 6 MIC LINE TRIM PHANTOM POWER AUX BUSS IN FX SEND FX RETURN MONITOR OUT RIGHT OUT LEFT OUT MODEL RM65 120 VAC 50 60 Hz 15 VA SERIAL NUMBER 65 MADE IN U S A WARNING DO NOT EXPOSE THIS EQUIPMENT TO RA
3. IN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC NE PAS ENLEVER C US 1 6 CHANNEL MIC INPUTS XLR input connectors for mic or line level signals 1 6 CHANNEL LINE INPUTS 1 4 input connectors for line level signals TRIM Adjusts the amount of input signal from the mic and line input jacks PHANTOM POWER 6 switches for turning on the microphone phantom power for the XLR inputs and are numbered for the channel they are assigned to DOWN is on UP is off AUX BUS IN 1 4 TRS stereo input to the main mix bus and may be used as an auxiliary stereo input for joining two RM65s together FX SEND 1 4 unbalanced jack for sending the signals assigned by each channel s FX Send control out to external effects FX RETURN 1 4 unbalanced jack for inputting signals from external effects devices MONITOR OUT 1 4 unbalanced jack for sending signals assigned by each channel s monitor output control to an auxiliary amplifier or monitoring system RIGHT and LEFT OUTPUT 1 4 TRS balanced jacks to be used as the unit s main outputs USING PHANTOM POWER Phantom power is a means of powering condenser microphones through the microphone cable The RM65 has individually switchable 36 volts of phantom power for each of its 6 channels through the XLR jacks The DIP switches on the rear of the unit are for swi
4. RM65 HEXMIX 6 x 4 Audio Mixer OWNERS MANUAL LIMITED WARRANTY This product is warranted to the original consumer purchaser to be free from defects in materials and workmanship under normal installation use and service for a period of one 1 year from the date of purchase as shown on the purchaser s receipt The obligation of Rolls Corporation under this warranty shall be limited to repair or replacement at our option during the warranty period of any part which proves defective in material or workmanship under normal installation use and service provided the product is returned to Rolls Corporation TRANSPORTATION CHARGES PRE PAID Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt In the absence of such purchase receipt the warranty period shall be one 1 year from the date of manufacture This warranty shall be invalid if the product is damaged as a result of deface ment misuse abuse neglect accident destruction or alteration of the serial number improper electrical voltages or currents repair alteration or maintenance by any person or party other than our own service facility or an authorized Service Center or any use violative of instructions furnished by us This one year warranty is in lieu of all expressed warranties obligations or liabilities ANY IMPLIED WARRANTIES OBLIGATIONS OR LIABILITIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MER CHAN
5. TABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE ONE YEAR DURATION OF THIS WRITTEN LIMITED WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESSED OR IMPLIED WHATSOEVER Some states do not allow the exclusion or limitation of special incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state ROLLS CORPORATION SALT LAKE CITY UTAH 7 01 FEATURES 6 XLR and 1 4 Inputs Individual 36 V Phantom Power Clip LEDs on each channel Input Trim Monitor FX Send and Pan on each channel Treble amp Bass control on each channel FX Return may be used as an additional input Stereo Aux Bus Input CLIP CLIP FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME CLIP CLIP FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME CLIP CLIP FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R FX SEND PAN
6. TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME CLIP CLIP FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME CLIP CLIP FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R PWR 17 8 0 4 13 LEFT RIGHT EFFECTS RETURN MASTER VOLUME FX SEND PAN TREBLE BASS MONITOR 0 10 0 10 L R VOLUME VOLUME CLIP CLIP RM65 Professional Audio Mixer CHANNEL CONTROLS VOLUME Adjusts the amount of signal sent through the channel and to the FX send and output CLIP LED Indicates that the channel is being overdriven MONITOR Adjusts the amount of signal sent from that channel to the Monitor Send jack The signal is pre fader pre Volume control BASS Controls the boost or cut of frequencies below 400 Hz for each channel TREBLE Controls the boost or cut of frequencies above 400 Hz for each channel Sheet 1 of 1 Title Size Date 7 Nov 2000 Rb 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V 12V VPHAN 6 5 7 8 6 5 7 8 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 8 7 10 11 12 6 14 2
7. nnel to the ON down position Instruments may be played into a microphone which is connected as indicated above or if you have active pickups in your instrument simply connect the output of your instrument to an RM65 Line Input as the acoustic guitar is shown in Figure 1 Electric guitars and basses normally are connected to an instrument amplifier or preamplifier Amplifiers may have microphones placed in front of the speaker or if the amp has a line level output check with the amplifier s owners manual it may also be connected to the mixer directly Keyboards and sound modules are connected directly to the RM65 s line inputs as shown To use the FX Loop connect a 1 4 unbalanced cable to the FX Send and to the Input on your signal processor or effects device Connect the Output of the signal processor or effects device to the RM65 FX Return jack The level of the effect will be controlled by the settings on the channels FX Sends and by the Output Level of your effects device The overall level of the effect will be controlled by the FX Return level on the front of the RM65 To use the Monitor feature of the RM65 connect the Monitor Out jack to a monitor amplifier via a 1 4 unbalanced cable Each channel s monitor level is controlled by that channel s Monitor level setting Be aware that the RM65 has no master monitor level so you will need to set the overall monitor level with the monitor amplifier and the Monitor Levels
8. of each channel Connect the Right and Left Main Outputs to the main amplifier s and make sure the amplifier is the correct rating for the speakers If you are operating in mono use either the Right or Left Output The RM65 may also be used for recording Connect microphones instruments and effects to the inputs as described above the connect the Right and Left outputs to your recording device and set the levels accordingly Figure 1 3 4 CHANNEL 1 MIC LINE TRIM CHANNEL 2 MIC LINE TRIM CHANNEL 3 MIC LINE TRIM CHANNEL 4 MIC LINE TRIM CHANNEL 5 MIC LINE TRIM CHANNEL 6 MIC LINE TRIM PHANTOM POWER AUX BUSS IN FX SEND FX RETURN MONITOR OUT RIGHT OUT LEFT OUT MODEL RM65 120 VAC 50 60 Hz 15 VA SERIAL NUMBER 65 MADE IN U S A WARNING DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK NO USER SERVICABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC NE PAS ENLEVER C US VOLUME PWR CLIP CLIP MONITOR AMPLIFIER WATTS 1 5 30 100 WATTS 1 5 30 100 VOLUME 1 VOLUME 1 PROTECT 0 10 0 10 MAINS AMPLIFIER
9. tching the power on and off When the little switch tab is down the power is on The number on the switch corresponds to the channel that is receiving the power If phantom power is not needed it should be switched off to avoid possible damage to a microphone or degraded sound quality SPECIFICATIONS Input Impedance 600 W balanced 50K W unbalanced 1 4 Output Impedance 50 W TRS Balanced Max Input Level 15 dBV XLR 600 W 18 dBV 1 4 Phase Shift lt 10 deg 20 Hz 20 kHz Phantom Power 36 V DC Input Connectors XLR and 1 4 Outputs 1 4 main balanced 17 dB max 1 4 monitor 17 dB max 1 4 FX send Max Gain Mains 60 dB mic 26 dB line Monitor 55 dB Tone controls 20 dB treb bass cut boost 400 Hz center Max S N Ratio 106 dB THD lt 003 IMD SMPTE lt 003 CMRR 52 dB Power 120 VAC 50 60 Hz 15 W Weight 7 lbs 3KG Size 19 x 1 75 x 6 5 48cm x 4 5cm x 17cm NOTES ___________________________________________________________ 2 5 OPERATION The RM65 is ideal for small combo groups where a small number of instruments and microphones need to be mixed together Refer to Figure 1 for an example of how to connect the inputs and outputs of your RM65 Connect microphones to balanced XLR cables and to the XLR inputs If any of these microphones are condenser microphones they will require phantom power To turn on the phantom power for an individual channel set the phantom power switch for that cha
Download Pdf Manuals
Related Search