RIDGID R350PNA User's Manual
Contents
1. Fencing Crate and Box Assembly Trusses Siding Pallets and Pallet Repair Subflooring OPERATION PREPARING THE TOOL FOR USE See Figure 2 Under normal use conditions the tool should be lubricated before connecting the tool to an air supply Add air tool lu bricant into the air fitting on the tool once daily with minimal use or twice a day with heavy use Only a few drops of oil at a time is necessary Too much oil will only collect inside the tool and will be noticeable in the exhaust cycle Before connecting the tool check the air compressor gauge to be sure it is functioning within the proper range of 50 120 psi A WARNING Disconnect the tool from the air supply before leaving the work area moving the tool to another location or handing the tool to another person Failure to do so could result in serious personal injury CONNECTING THE TOOL TO AN AIR SUPPLY See Figures 2 3 A DANGER Do not use oxygen combustible gases or bottled gases as a power source for this tool The tool will explode and cause death or serious injury This tool is designed to operate on clean dry compressed air at regulated pressures between 50 and 120 psi The correct air pressure is the lowest pressure that will do the job AIR FITTING Fig 2 NOTE Air pressure that is higher than 120 psi may damage the tool The tool and air hose must have a hose coupling that allows all pressure to be removed from the tool when the2. be actuated or that satisfies one require ment for the tool to be actuated Actuate tool To cause movement of the tool component s intended to drive a fastener Actuation system The use of a trigger workpiece contact and or other operat ing control separately or in some combination or sequence to actuate the tool e Single sequential actuation An actuation system in which there is more than one operating control and the operating controls must be activated in a specific sequence to actuate the tool Additional actuation can occur when a specific operat ing control other than a workpiece contact is released and re activated e Contact actuation An actuation system in which there is more than one operating control and the operating controls can be activated in any sequence to actuate the tool Addi tional actuation can occur when any operating control is released and re activated Selective actuation An actuation system that allows discrete selection of two or more of the following actuation systems single sequential actuation full sequential actuation or contact actuation One or more of the selections shall be single sequential actuation or full sequential actuation Air inlet port In an air tool the opening to which the compressed air supply is connected usually by means of a threaded fitting Fastener A staple pin brad nail or other fastening device which is designed and manufactured for use in the tools
3. coupling is disconnected A WARNING Always use a coupling that discharges all the compressed air in the tool at the time the fitting or hose coupling is disconnected Using a coupling that does not discharge the compressed air could cause unintended operation and serious personal injury A WARNING Do not climb rigging or scaffolding while carrying a tool that is connected to an air hose Doing so could result in serious personal injury Connect the tool to the air supply with a 1 4 in female quick connector A 3 8 in female quick connector may be used in situations where a 1 4 in supply line is not available For maximum tool performance a 3 8 in supply line and fittings are required OPERATION LOADING THE TOOL WITH NAILS See Figures 3 4 A WARNING The tool s driving mechanism may cycle when the tool is first connected to the air supply Always connect the tool to the air supply before loading nails to prevent injury from unintended cycling Always make sure the nosepiece is empty at the beginning of each work session before connecting to an air supply E Connect the tool to the air supply E With the nose of the tool pointed away from you feed a nail into the nosepiece Be sure the nails are pointed downward and at the angle shown in figure 4 A WARNING Keep the tool pointed away from yourself and others when loading nails Failure to do so could result in possible serious personal injury A WARN
4. eye protection which is marked to comply with ANSI 287 1 Additional safety protection will be required in some environments For example the working area may in clude exposure to noise level which can lead to hearing damage The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area Some environments will require the use of head protection equipment When required the employer and user must ensure that head protection conforming to ANSI Z89 1 1997 is used Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Keep fingers away from trigger when not driving fasten ers to avoid accidental firing Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask nonskid safety shoes hard hat or hearing protection must be used for appropriate conditions Do not use on a ladder or unstable support Stable footing
5. occur possibly causing injury SAVE THESE INSTRUCTIONS E Refer to them frequently and use them to instruct others who may use this tool If you loan someone this tool loan them these instructions also SYMBOLS Some of the following symbols may be used on this tool Please study them and learn their meaning Proper interpreta tion of these symbols will allow you to operate the tool better and safer SYMBOL NAME DESIGNATION EXPLANATION Read The Operator s To reduce the risk of injury user must read and understand operator s manual Manual before using this product Always wear safety goggles or safety glasses with side shields and as necessary Pye Protection a full face shield when operating this product Eye Ear and Head Always wear other personal protective equipment such as hearing protection Protection and a hard hat when needed D Keep Hands Away Keep hands and body away from the discharge area of the tool A Safety Alert Precautions that involve your safety X Hot Surface To reduce the risk of injury or damage avoid contact with any hot surface The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING 3 Indicates an imminently hazardous situation which if not avoided will result in death or A DANGER serious injury _ Indicates a potentially hazardous situation which if not avoided could result in death or A WARNING serious i
6. on a solid surface enables better control of the tool in unexpected situations TOOL USE AND CARE Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use tool if trigger does not actuate properly Any tool that cannot be controlled with the trigger is dangerous and must be repaired Check operation of the workpiece contact mechanism frequently Do not use the tool if the workpiece contact mechanism is not working correctly as accidental driving of a fastener may result Do not interfere with the proper operation of the workpiece contact mechanism Store idle tools out of the reach of children and other untrained persons Tools are dangerous in the hands of untrained users Maintain tools with care Follow maintenance instruc tions Properly maintained tools are easier to control Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only fasteners that are recommended for your model Keep the tool and its handle dry clean and free from oil and grease Always use a clean cloth when clean ing Never use brake fluids gasoline petroleum based products or any strong solvents to clean your tool Fol lowing this rule will reduce the risk of loss of
7. ANTY Proof of purchase must be presented when requesting warranty service This product is manufactured by One World Technologies Inc The trademark is licensed from RIDGID Inc All warranty communications should be directed to One World Technolo gies Inc attn RIDGID Pneumatic Tool Technical Service at toll free 1 866 539 1710 90 DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase if you are dissatisfied with the performance of this RIDGIDe Pneumatic Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY This warranty on RIDGIDe Pneumatic Tools covers all defects in workmanship or materials and normal wear items for three years following the purchase date of the tool Warranties for other RIDGIDe products may vary HOW TO OBTAIN SERVICE To obtain service for this RIDGIDe tool you must return it freight prepaid or take it in to an authorized service center for RIDGIDe branded pneumatic tools You may obtain the location of the authorized service center nearest you by calling toll free 1 866 539 1710 or by logging on to th
8. ING Never load nails with the nosepiece depressed Doing so could result in possible serious personal injury SETTING THE AIR PRESSURE The amount of air pressure required will depend on the size of the nail and the workpiece material Begin testing the depth of drive by driving a test nail into the same type of workpiece material used for the actual job Drive a test nail with the air pressure set at 50 55 psi Raise or lower the air pressure to find the lowest setting that will perform the job with consistent results It may be possible to achieve the desired depth with air pressure adjustments alone If finer adjustments are needed use the drive depth adjustment on the tool 10 AIR HOSE CONNECTOR SWIVEL CONNECTOR NOSEPIECE NAIL Fig 4 OPERATION DRIVE DEPTH ADJUSTMENT See Figure 5 The driving depth of the nail may be adjusted It is advisable to test the depth on a scrap workpiece to determine the required depth for the application To determine depth of drive first adjust the air pressure and drive a test nail To achieve the desired depth use the drive depth adjustment on the tool E Disconnect the tool from the air supply E Turn the depth selector left or right to change the driving depth E Reconnect the tool to the air supply E Drive a test nail after each adjustment until the desired depth is set ADJUSTING THE HAND STRAP See Figure 6 7 E Disconnect the tool from the air s
9. OPERATOR S MANUAL PALM NAILER R350PNA RIDGID Your palm nailer has been engineered and manufactured to our high standards for dependability ease of operation and operator safety When properly cared for it will give you years of rugged trouble free performance A WARNING To reduce the risk of injury the user must read and understand the operator s manual before using this product Thank you for buying a RIDGIDe product SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS ME aea U CHO a E E ee eetntea nereee diene dente ce eted een E eee ede de end sled ead WeRco rea eeedi E 2 E Gnora Saloy RUGS sisirain kiana D RERE E ORARE NTE E E R AAE DA E AEEA 3 E Specie o dely RUES igini thee Acces an na ct fates E EAE AREA SAR iR co san sess Sexes sbhenceseesseae 4 E S E A O A E A A E EA S A E E A E AT 5 E Glossary Of TOMS siessenek n eT aaee PENNI sete AARATI TANANA ENNA Gene AREER NEA deebe pease EEEN ENEE ar NE eeu ecu EEan iS 6 Bae E T EA T A E E A E T T T E ETT 7 E Assman S 8 ME OPS HALON vies A E E E E E E AET 8 11 E VAIN NAN CS nganom aTa R EEA RE 12 i e e e e E E A E A T E T E A E A A TA 13 E Troubleshooting wei cssiveec peed tices teed eaece event yh ee ities EE AAAA anA KAAN AREENA ETEEN ASA dine eine edie edie ESEN 13 ME WANT AUNLY secs E A E E E T E T pacteaevaedeanesd E tinea 14 E Customer Service IMPOMMATIOM 2 2 2cc _cesescececnecsaeedesssnzbeg ceadaacetepesaseeaceeasaideeteaeaeagesacnea ideas ATEKA pana s
10. aa lusde tend sesTuat yd ceve VEKAN aa EEN 50 120 psi se Sen E E E ce eeadeeesoveceaw 1 4 in NPT A saneetccesstactsees esate Common Bulk Nails 4d 16d AE LA E E E E EE EE E T 1 1 2 in 3 1 2 in N ON O aceseeeteen neta 2 7 Ibs QUICK CONNECT SWIVEL CONNECTOR ee NOSEPIECE Fig 1 DEPTH OF DRIVE ADJUSTMENT The tool free depth of drive adjustment lets the operator select precise driving depth of the fastener MAGNETIC NAIL GUIDE The magnetic nail guide holds nails securely in place while driving nails into the workpiece QUICK CONNECT SWIVEL CONNECTOR The quick connect swivel connector helps prevent hose tangles SELF CLEANING AIR FILTER The self cleaning air filter keeps debris out of the tool and extends the life of the tool ASSEMBLY UNPACKING This product has been shipped completely assembled Carefully remove the tool and any accessories from the box Make sure that all items listed in the packing list are included Inspect the tool carefully to make sure no breakage or damage occurred during shipping Do not discard the packing material until you have care fully inspected and satisfactorily operated the tool If any parts are damaged or missing please call 1 866 539 1710 for assistance PACKING LIST Palm nailer Oil Hex Key Case Operator s Manual OPERATION A DANGER Do not use oxygen combustible gases or bottled gases as a power source for this tool The tool will explode and cause d
11. cbehcenaasceesparaes Back Page INTRODUCTION This tool has many features for making its use more pleasant and enjoyable Safety performance and dependability have been given top priority in the design of this product making it easy to maintain and operate GENERAL SAFETY RULES AX DANGER READ AND UNDERSTAND TOOL LABELS AND MANUAL Failure to follow warnings could result in DEATH or SERIOUS INJURY SAVE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit Cluttered benches and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control PERSONAL SAFETY Eye protection which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading operating or servicing this tool Eye protection is required to guard against flying fasteners and debris which could cause severe eye injury The employer and or user must ensure that proper eye protection is worn We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses that provide protection against flying particles both from the front and side Always use
12. control and deterioration of the enclosure plastic SERVICE Tool service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel may result in a risk of injury When servicing a tool use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of injury SPECIFIC SAFETY RULES Know your pneumatic tool Read operator s manual carefully Learn its applications and limitations as well as the specific potential hazards related to this tool Following this rule will reduce the risk of electric shock fire or serious injury Always wear safety glasses with side shields Everyday glasses have only impact resistant lenses They are NOT safety glasses Following this rule will reduce the risk of eye injury Protect your lungs Wear a face or dust mask if the op eration is dusty Following this rule will reduce the risk of serious personal injury Protect your hearing Wear hearing protection during extended periods of operation Following this rule will reduce the risk of serious personal injury Make sure the hose is free of obstructions or snags Entangled or snarled hoses can cause loss of balance or footing and may become damaged Use the tool only for its intended use Do not discharge fasteners into open air Use the pneumatic tool only for the purp
13. e Always ensure that the workpiece contact is fully posi tioned above the workpiece Positioning the workpiece contact only partially above the workpiece could cause the fastener to miss the workpiece completely and result in serious personal injury Do not drive fasteners near edge of material The workpiece may split causing the fastener to ricochet injuring you or a co worker Be aware that the nail may follow the grain of the wood causing it to protrude un expectedly from the side of the work material E Keep hands and body parts clear of immediate work area Hold workpiece with clamps when necessary to keep hands and body out of potential harm Be sure the workpiece is properly secured before pressing the nailer against the material The workpiece contact may cause the work material to shift unexpectedly E Keep face and body parts away from back of the tool cap when working in restricted areas Sudden recoil can result in impact to the body especially when nailing into hard or dense material E During normal use the tool will recoil immediately after driving a fastener This is a normal function of the tool Do not attempt to prevent the recoil by holding the nailer against the work Restriction to the recoil can result in a second fastener being driven from the nailer Grip the handle firmly let the tool do the work and do not place second hand on top of tool or near exhaust at any time Failure to heed this warning can resu
14. e RIDGIDe website at www ridgid com When requesting warranty service you must present the original dated sales receipt The authorized service center will repair any faulty workmanship and either repair or replace any part covered under the warranty at our option at no charge to you 14 WHAT IS NOT COVERED This warranty applies only to the original purchaser at retail and may not be transferred This warranty only covers de fects arising under normal usage and does not cover any malfunction failure or defect resulting from misuse abuse neglect alteration modification or repair by other than an authorized service center for RIDGIDe branded pneumatic tools Consumable accessories provided with the tool such as but not limited to fasteners oil and safety glasses are not covered RIDGID INC AND ONE WORLD TECHNOLOGIES INC MAKE NO WARRANTIES REPRESENTATIONS OR PROM ISES AS TO THE QUALITY OR PERFORMANCE OF ITS PNEUMATIC TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY ADDITIONAL LIMITATIONS To the extent permitted by applicable law all implied war ranties including warranties of MERCHANTABILITY or FIT NESS FOR A PARTICULAR PURPOSE are disclaimed Any implied warranties including warranties of merchantability or fitness for a particular purpose that cannot be disclaimed under state law are limited to three years from the date of purchase One World Technologies Inc and RIDGID Inc are not responsible f
15. eath or serious injury A WARNING Do not allow familiarity with tools to make you careless Remember that a careless fraction of a second is sufficient to inflict severe injury A WARNING Always wear safety goggles or safety glasses with side shields when operating tools Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury A WARNING Disconnect the tool from the air supply before leaving the work area moving the tool to another location or handing the tool to another person Failure to do so could result in serious personal injury A WARNING If any parts are damaged or missing do not operate this tool until the parts are replaced Failure to heed this warning could result in possible serious personal injury A WARNING Do not attempt to modify this tool or create accessories not recommended for use with this tool Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury A WARNING Always wear eye protection Eye protection does not fit all operators in the same way Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides APPLICATIONS You may use this tool for the purposes listed below Framing Sheathing Roof Sheathing Floor Decking Exterior Decks Engineered Lumber Blocking Sub Assemblies Bridging
16. grease etc A WARNING Do not at any time let brake fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury 12 LUBRICATION Frequent but not excessive lubrication is required for best performance Oil added through the air line connection will lubricate the internal parts Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool resulting in poor tool performance and frequent tool maintenance COLD WEATHER OPERATION For cold weather operation near and below freezing the moisture in the air line may freeze and prevent tool operation We recommend the use of air tool lubricant or permanent antifreeze ethylene glycol as a cold weather lubricant CAUTION Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure NOTE Some commercial air line drying liquids are harmful to O rings and seals Do not use these low temperature air dryers without checking compatibility AIR SUPPLY PRESSURE AND VOLUME Air volume is as important as air pressure The air volume supplied to the tool may be inadequate because of under size fittings and hoses or from the effects of dirt and water in the system Restricted air flow wi
17. ll prevent the tool from receiving an adequate volume of air even though the pres sure reading is high The results will be slow operation or reduced driving power Before evaluating tool problems for these symptoms trace the air supply from the tool to the supply source for restrictive connectors low points contain ing water and anything else that would prevent full volume flow of air to the tool ACCESSORIES To order parts and maintenance kits call 1 866 539 1710 Driver maintenance Kit cccccccceceee cece ee eeeeeeee eae ea ee nett eee teeta aaa aaa eee eee eee e eee aaaaaaee eee eeeeeeeeaaaaaaaaaaaeeeeeeeeeeeeeas 079019001034 Overhaul Kitveds aigcasissieiind listenin needed a a ETS 079019001035 A WARNING Current attachments and accessories available for use with this tool are listed above Do not use any attachments or accessories not recommended by the manufacturer of this tool The use of attachments or accessories not recommended can result in serious personal injury TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Tool does nothing or operates Inadequate air supply Verify adequate air supply sluggishly Inadequate lubrication Lubricate tool Worn or damaged O rings or bumper Install Overhaul Kit and replace O rings Tool jams frequently Incorrect fasteners Verify that fasteners are the correct size Damaged fasteners Replace fasteners 13 WARRANTY RIDGIDe PNEUMATIC TOOL 3 YEAR LIMITED SERVICE WARR
18. lt in serious personal injury E Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury E Do not drive fasteners close to the edge of the workpiece as the wood may split allowing the fastener to be deflected possibly causing injury AIR SUPPLY AND CONNECTIONS E Do not use oxygen combustible gases or bottled gases as a power source for this tool as tool will ex plode possibly causing injury or death E Do not use with an air compressor which can po tentially exceed 200 psi as tool may burst possibly causing injury E The connector on the tool must not hold pressure when air supply is disconnected If an incorrect fitting is used the tool can remain charged with air after discon necting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury E Always disconnect air supply e Before making adjustments e When servicing the tool e When clearing a jam e When tool is not in use e When moving to a different work area as accidental actuation may occur possibly causing injury LOADING TOOL E Do not load the tool with fasteners when any one of the operating controls is activated When loading tool E Never place a hand or any part of body in fastener discharge area of tool E Never point tool at anyone E Do not depress the workpiece contact as accidental actuation may
19. njury s Indicates a potentially hazardous situation which if not avoided may result in minor or A CAUTION moderate injury CAUTION Without Safety Alert Symbol Indicates a situation that may result in property damage SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service we suggest you return the product to your nearest use this orodlict until you read thoroudhly and AUTHORIZED SERVICE GENTER Tor rapal Mhen servic arderstand Scan the operator s Gane ing use only identical replacement parts If you do not understand the warnings and instructions in the operator s manual do not use this product Call RIDGID customer service A WARNING The operation of any power tool can result in To avoid serious personal injury do not attempt to A WARNING The operation of any power tool can result in foreign objects being thrown into your eyes which can result in severe eye damage Before beginning power tool operation always wear safety goggles or safety glasses with side shields and when needed a full face shield We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields Always use eye protection which is marked to comply with ANSI 287 1 SAVE THESE INSTRUCTIONS 5 GLOSSARY OF TERMS Activate operating controls To move an operating control so that it is in a position that allows the tool to
20. or direct indirect incidental or conse quential damages Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential dam ages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state One World Technologies Inc P O Box 35 Hwy 8 Pickens SC 29671 NOTES 987000 109 08 10 07 REV 01 OPERATOR S MANUAL PALM NAILER R350PNA Customer Service Information For parts or service contact your nearest RIDGIDe authorized service center Be sure to provide all relevant information when you call or visit For the location of the authorized service center nearest you please call 1 866 539 1710 or visit us online at www ridgid com The model number of this tool is found on a plate attached to the rear portion of the magazine Please record the serial number in the space provided below When ordering repair parts always give the following information Model No R3SOPNA Serial No
21. ose for which it was designed Do not use hardened nails in this tool Use only the fasteners recommended for this tool Use of the wrong fasteners could result in poor fastener feed ing jammed fasteners and nails leaving the tool at erratic angles If fasteners are not feeding smoothly and properly discontinue their use immediately Jammed and improperly feeding fasteners could result in serious personal injury Never use this tool in a manner that could cause a fastener to be directed toward anything other than the workpiece Do not use the tool as a hammer Do not alter or modify this tool from the original design or function without approval from the manufacturer Always be aware that misuse and improper handling of this tool can cause injury to yourself and others Never leave a tool unattended with the air hose attached Do not operate this tool if it does not contain a legible warning label Do not continue to use a tool that leaks air or does not function properly OPERATION Always assume that the tool contains fasteners Always handle the tool with care e Respect the tool as a working implement e Never engage in horseplay e Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur possibly causing injury Do not point the tool toward yourself or anyone whether it contains fasteners or not Do not actuate the tool unless you intend to drive a fastener into the workpiec
22. upply E Determine which hand the palm nailer will be used with and attach the hand strap to the latch according to figure 6 E Pull the hand strap hook and loop top apart from the bottom E Insert hand and tighten to fit E Reattach hand strap hook and loop top to bottom DRIVING NAILS E Place tip of the nail against the workpiece E Push the tool firmly with your palm Keep the nail in line with the nosepiece as the nail is driven E Remove the tool from the nail when complete A WARNING Never hold the nail with your hand or fingers while driving the nail Doing so could result in possible serious personal injury TO DECREASE DEPTH TO INCREASE DRIVE DEPTH DEPTH ADJUSTMENT Fig 5 HOOK AND LOOP AND LOOP TOP 11 MAINTENANCE A WARNING When servicing use only identical RIDGID replacement parts Use of any other parts may create a hazard or cause product damage Av WARNING Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust If operation is dusty also wear a dust mask A WARNING Disconnect the tool from the air supply before performing maintenance Failure to do so could result in serious personal injury GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil
23. within the scope of this standard Jam An obstruction in the feed or drive areas of the tool Maximum air pressure The maximum allowable pressure of the compressed air as specified by the manufacturer for operating a tool Operating control A control that separately or as part of an actuation system can cause the actuation of a tool Trigger A tool operating control activated by a tool operator s fin gers Workpiece The intended object into which a fastener is to be driven by a tool Workpiece contact An operating control element or assembly on the tool in tended to be activated by the material to be fastened FEATURES PRODUCT SPECIFICATIONS Operating PreSSUre sispan a a E Ar Poteronosnnna iaa Fastener R amp ne ccccccceeeeeeeceeceeeeeeeeeeeeeeeeeeaaaaeeeeeeeeeeeeeeneneees Fastener Length ccciccadnen nani daanieaii ieee WIGME E aves svesdveuies seed rendsvecds E T HAND STRAP DEPTH OF DRIVE ADJUSTMENT KNOW YOUR PALM NAILER See Figure 1 The safe use of this product requires an understanding of the information on the tool and in this operator s manual as well as a knowledge of the project you are attempting Before use of this product familiarize yourself with all operating features and safety rules HAND STRAP The hand strap is attachable from the left or the right with the convenient latches on the top of the palm nailer and is adjustable for hand size waves vate a a esses ay
Download Pdf Manuals
Related Search