Renesas R0E436640CFK20 User's Manual
Contents
1. 10 0 max10 10 14 0 mn13 50 1 gt lt 0 50 0 05 10 0 max10 10 a 14 0 mn13 50 1 gt Unit mm Figure 4 External dimensions and a recommended foot pattern of the ROE436640CFK20 7 Precautions A CAUTION Cautions to Be Taken for This Product Q Do not connect anything to the NC pins Do not pull or excessively flex the cable The cable may cause a break When connecting the emulator and IC socket be sure to use the included screws M2 x 12mm When connecting the IC socket and socket cover be sure to use the included screws M2 x 6mm When connecting the IC socket and socket cover use a Phillips type screwdriver whose head matches the screw head If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening The tightening torque must be 0 29 Nem or less If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Fasten the IC socket to the socket cover with the four screws M2 x 6 mm with flat washers provided Each screw should b2. Manual 2 4 ROE436640CFK20 a SS KS NF IC socket TTT OOOO Screws M2x12mm Flat washers For fixing converter board TTT OROROORO Screws M2x6mm Flat washers For on board evaluation Socket cover Figure 1 Package components of the ROE436640CFK20 1 Debugging N ROE436640CPE00 Screws M2x12mm R0E436640CFK20 2 On board evaluation R0E436640CIF00 Screws M2x6mm T T Ta 1 Socket cover Flat washers D7 MCU with on chip flash memory etc e M we SS IC socket 4 M PA 64 pin 0 5mm pitch foot pattern PLQP0064KB A PLQP0064KC A No 1 pin These products are included with the ROE436640CFK20 pakcage Figure 2 Usage of the ROE436640CFK20 5 Connection Procedure See Figure 3 The procedure for connecting the ROE436640CFK20 is shown below 1 Mount the IC socket on the user system 2 Connect the ROE436640CPE00 and ROE436640CIF00 3 Connect the ROE436640CFK20 and IC socket Fasten the IC socket to the socket cover with the four screws M2 x 12 mm provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components e When connecting the IC socket and socket cover use a Phi
3. RENESAS ROE436640CFK20 Converter Board for 64 pin 0 5mm pitch LQFP User s Manual 1C149 064 075 B51 is a trademark of Yamaichi Electronics Co Ltd Keep safety first in your circuit designs Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corporation Renesas Solutions Corporation or a third party Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage or infringement of any third party s rights originating in the use of any product data diagrams charts programs algorithms or circuit application examples contained in these materials All information contained i
4. by Yamaichi Electronics Co Ltd PKS Screws M2 x 12mm 4 pcs Flat washers for fixing the converter board 4 pes IC socket 1 pe Socket cover 1 pe Screws M2 x 6mm 4 pcs Flat washers for on board evaluation 4 pes 3 ROE436640CFK20 User s Manual 1 pe This manual 3 Specifications Table 1 Specifications H8 3664 Group H8 3664N H8 3694 Group H8 3694N H8 3687 Group H8 3687N H8 3672 Group H8 36077 Group H8 36014 Group H8 36079 Group H8 36064 Group H8 36094 Group H8 36087 Group Applicable group PLQP0064KB A previous FP 64K PLQP0064KC A previous FP 64E Applicable package Between ROE436640CPE00 and ROE436640CFK20 50 times guaranteed Insertion removal iterations of connector 4 Usage See Figure 2 The ROE436640CFK20 can be used for debugging and board mounted evaluation in common by mounting an IC socket on the user system 1 For debugging Mount the IC socket on the foot pattern of the user system in that order After connecting the R0E436640CPE00 and ROE436640CIF00 connect the ROE436640CFK20 to the IC socket And fix them with the screws M2 x 12mm included with the ROE436640CFK20 For onboard evaluation Mount an H8 300H Tiny Series MCU in that order on the IC socket on the user system And fix them with the screws M2 x 6mm included with the ROE436640CFK20 2 Before using the ROE436640CFK20 be sure to read 7 Precautions on page 4 and the ROE436640CPEO00 User s
5. can be put to practical use by performing integration test evaluation or some experiment else In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge However this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances This product has been developed by assuming its use for program development and evaluation in laboratories Therefore it does not fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan If the requirements shown in the CAUTION sentences are ignored CAUTION the equipment may cause personal injury or damage to the products Renesas Tools Homepage _http www renesas com tools Rev 2 00 Feb 15 2007 1 4 REJ10J0921 0200 Renesas Technology www renesas com 1 Outline The ROE436640CFK20 is a converter board for connecting the compact emulator ROE436640CPE00 for H8 300H Tiny Series to a foot pattern for 64 pin 0 5mm pitch LQFP PLQP0064KC A of H8 3664 Group 2 Package Components See Figure 1 Table 1 Package Components Item Quantity 1 ROE436640CFK20 Base board ROE436640CIFO0 and 150mm 1 pe FFC cable included 2 IC149 064 075 B51 1 bk made
6. e tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components After checking the location of pin 1 on the IC socket apply epoxy resin adhesive to the bottom of the IC socket and fasten it to the user system before soldering Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU IMPORTANT Notes on This Product We cannot accept any request for repair For purchasing the IC149 064 075 B51 contact the following Yamaichi Electronics Co Ltd http www yamaichi com For inquiries about the product or the contents of this manual contact your local distributor Renesas Tools Homepage http www renesas com tools 4 4
7. erein Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corporation Renesas Solutions Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein Precautions to be taken when using this product This product is a development supporting unit for use in your program development and evaluation stages In mass producing your program you have finished developing be sure to make a judgment on your own risk that it
8. llips type screwdriver whose head matches the screw head e If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening The tightening torque must be 0 13 Nem or less If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary _ ROE436640CPE00 Screws M2x12mm T we 2 Flat washers ic ROE436640CFK20 R0E436640CIF00 nae Ea AE Eo 0 q wa KS IC socket wo Jo we A lt gt DEP 0 5mm pitch foot pattern w PLQP0064KB A PLQP0064KC A Figure 3 Connection procedure of the ROE436640CFK20 6 External Dimensions and a Recommended Foot Pattern See Figure 4 Note that the dimensions of the recommended foot pattern in Figure 4 are somewhat different from those of the actual foot pattern 2 5 bls ROE436640CFK20 REV A MADE IN JAPAN JY A 2 t y I gt 4 0 30 0 05
9. n these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corporation Renesas Solutions Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corporation and Renesas Solutions Corporation by various means including the Renesas home page http Awww renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage liability or other loss resulting from the information contained h
Download Pdf Manuals
Related Search