Renesas H8/329 Series User's Manual
Contents
1.2. Interface Cable RENESAS Table 1 lists the HS3297ECH61H components Please make sure you have all of these components when unpacking Table 1 HS3297ECH61H Components No Component Quantity Remarks 1 Cable body 1 Includes flat cable 2 Cable head 1 3 IC socket 1 For the FP 64A package 4 Socket cover 1 For installing an FP 64A packaged MCU 5 Screws M2 0 x 12 mm 4 For fastening cable head with four flat washers 6 Screws M2 0 x 8 mm 4 For installing an FP 64A packaged MCU with four flat washers 7 Documentation 1 User s manual for HS3297ECH61H this manual 3 RENESAS Section 2 Connection Procedures 2 1 Connecting User System Interface Cable to Emulator Station A WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable body to the emulator station follow the instructions below 1 Make sure the user system and emulator station are turned off 2 After making sure the direction of the cable body connector is correct firmly insert the cable body connector into the emulator station socket figure 2 Emulator station Figure 2 Connecting User System Int
3. System clock Figure 9 Oscillator Circuit 14 RENESAS Section 5 Notice 1 Make sure that pin on the user system IC socket is correctly aligned with pin on the cable head before inserting the cable head into the user system IC socket 2 The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU 3 This user system interface cable is specifically designed for the HS3008EPI60H emulator Do not use this cable with any other emulator station 4 To prevent breaking of wires in the cable body do not place heavy or sharp metal objects on the user system interface cable 5 While the emulator station is connected to the user system with the user system interface cable force must not be applied to the cable head Place the emulator station user system interface cable and user system as shown in the example in figure 10 Emulator station Place components so that the cable body and cable head are paral memeh el to the user system Cable head is parallel to emulator station i a Cable head is parallel i to user system User system Figure 10 User Cable Location Example 6 The P1 short connector is used for testing Do not remove the short pins that are inserted in the sides of pin and pin 2 Figure 11 P1 Short Connector RENESAS
4. H8 3297 Series H8 329 Series QFP 64A User System Interface Cable HS3297ECH61H for E6000 Emulator User s Manual CENESAS HS3297ECH61HE C Cautions Renesas neither warrants nor grants licenses of any rights of Renesas s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Renesas bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in this document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Renesas makes every attempt to ensure that its products are of high quality and reliability However contact Renesas s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury such as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Renesas particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions an
5. d other characteristics Renesas bears no responsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Renesas product does not cause bodily injury fire or other consequential damage due to operation of the Renesas product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whole or part of this document without written approval from Renesas Contact Renesas s sales office for any questions regarding this document or Renesas semiconductor products Preface Thank you for purchasing the E6000 emulator for the Renesas s original microprocessor H8 300 series The HS3297ECH61H is a user system interface cable that connects an H8 300 series E6000 emulator HS3008EPI60H hereinafter referred to as the emulator to the IC socket for a QFP 64A package package code FP 64A for the H8 3297 series or H8 329 series MCU on the user system RENESAS Contents Section I Configuration 42 roger ee he ere E EEE NRE 1 Section 2 Connection Procedures ii spcssduniesWapshindionpads acepudeensendne satvendvadeenaeundupnde 4 2 1 Connecting User System Interface Cable to Emulator Station dssserer renerne 4 2 2 Connecting User System Interface Cable
6. e 0 5 mm manufactured by YAMAICHI ELECTRONICS Co Ltd Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11 RENESAS Section 3 Installing the MCU to the User System CAUTION Check the location of pin 1 before inserting Use a Phillips type screwdriver whose head matches the screw head The tightening torque must be 0 0784 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the MCU does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Check the location of pin before inserting the MCU into the IC socket on the user system as shown in figure 8 After inserting the MCU fasten the socket cover with the provided four screws M2 0 x 8 mm Take special care such as manually securing the IC socket soldered area to prevent the IC socket from being damaged by overtightening the screws or twisting the components RENESAS Screws M2 0 x 8 mm with flat washers Pin 1 mark IC socket a IC149 064 008 B5 manufactured by User system YAMAICHI ELECTRONICS Co Ltd Figure 8 Installing MCU to Us
7. er System RENESAS Section 4 Verifying Operation 1 When using the H8 300 series E6000 emulator HS3008EPI60H turn on the emulator according to the procedures described in the H8 300 Series E6000 Emulator User s Manual HS3008EPI60HE 2 Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins If an error is detected recheck the soldered IC socket and the location of pin 1 3 The emulator connected to this user system interface cable supports two kinds of clock sources an emulator internal clock and an external clock on the user system For details refer to the H8 300 Series E6000 Emulator User s Manual HS3008EPI60HE To use the emulator internal clock Select the clock in the emulator station as the system clock 6 by using the CLOCK command emulator command To use the external clock on the user system as the system clock Select target clock t or t2 with the CLOCK command emulator command Supply the external clock from the user system to the emulator Connect a crystal oscillator to the EXTAL and XTAL terminals for the system clock In the H8 3297 series the system clock has the same frequency as the external clock and in the H8 329 series the system clock has a half frequency of the external clock Figure 9 shows the oscillator circuit on the user system interface cable R1 1MQ HCU04 HCU04 Pe eae R2 270 Q EXTAL XTAL
8. erface Cable to Emulator Station RENESAS 22 Connecting User System Interface Cable to User System A WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part Before connecting make sure that pin 1 on both sides are correctly aligned Failure to do so will damage the user system and the emulator product or will result in PERSONAL INJURY The USER PROGRAM will be LOST To connect the cable head to the user system follow the instructions below 2 2 1 Installing IC Socket After checking the location of pin 1 on the IC socket apply epoxy resin adhesive to the bottom of the IC socket for an FP 64A package and fasten it to the user system before soldering 2 2 2 Soldering IC Socket After fastening solder the IC socket for an FP 64A package to the user system Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets Use slightly more solder than the MCU 2 2 3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting Align pin 1 on the IC socket for an FP 64A package on the user system with pin 1 on the user system interface cable head and insert the user system interface cable head into the IC socket on the user system as shown in figure 3 RENESAS 2 2 4 Fastening Cable Head CAUTION Use a Phillips type screwdriver whose head matches the sc
9. rew head The tightening torque must be 0 0784 Nem or less If the applied torque cannot be accurately measured stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening If a screw is tightened too much the screw head may break or an IC socket contact error may be caused by a crack in the IC socket solder If the emulator does not operate correctly cracks might have occurred in the solder Check conduction with a tester and re solder the IC socket if necessary Fasten the user system interface cable head to the IC socket for an FP 64A package on the user system with the four screws M2 0 x 12 mm provided Each screw should be tightened a little at a time alternating between screws on opposing corners Take special care such as manually securing the IC socket soldered area to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components RENESAS Screws M2 0 x 12 mm and flat washers Cable head Pin 1 IC socket IC149 064 008 B5 4 manufactured by YAMAICHI ELECTRONICS User system Co Ltd Figure 3 Connecting User System Interface Cable to User System RENESAS 2 2 5 Connecting Cable Body to Cable Head Connect the cable body to the cable head Cable body Remove jig zZ TA Cable head User system Figure 4 Fas
10. tening Cable Body RENESAS 2 3 Recommended Dimensions for User System Mount Pad Figure 5 shows the dimensions for the recommended mount pad footprint for the user system with an IC socket for an FP 64A package IC149 064 008 B5 manufactured by YAMAICHI ELECTRONICS Co Ltd Note that the dimensions in figure 5 are somewhat different from those of the actual chip s mount pad 2 20 80 min e p a 2 14 80 max gt lt 0 80x15 12 00 0 10 gt 0 45 0 10 0 80 0 05 49 0 05 ai ma y SS SS L A A SS SS 8 o 2 o H H f 5 ci I 19 x o o SSS SS y SS S55 lll il Unit mm Figure 5 Recommended Dimensions for Mount Pad RENESAS 2 4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6 eg g A REN 17 8 jp gt ge 45 7 gt 4 0 l 63 5 Sy itt Unit mm Tolerance 0 5 mm Figure 6 Dimensions for User System Interface Cable Head 10 RENESAS 2 5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions after connecting the user system interface cable head to the user system are shown in figure 7 Cable head t IC socket Unit mm User system IC149 064 008 B5 Toleranc
11. to User System eee eeeeeeeeeeeeneeeeceseeeeeeeenees 5 22 1 Installing IC Socket siiscscssse dai aidiv aiden mectechisen tied a teser 5 222 SOldEriNS IC SOCK succre ecenin sas aikee e aE EEEE ERENER 5 22 3 Inserting Cable Head s tsisissdeeessec tii deni aedei ni atiee bliin nek 5 2 2 4 Bastening Cable Headissa aeee EE EOE EEE 6 2 2 5 Connecting Cable Body to Cable Head 0000 reen rrere rr e nerne 8 2 3 Recommended Dimensions for User System Mount Pad ec eeeseeseeeeeneeeeeeseeeeeeeenees 9 2 4 Dimensions for User System Interface Cable Head tee eeecceseeceeseceeeeecnereecsseeeeeaeenees 10 2 5 Resulting Dimensions after Connecting User System Interface Cable eee ees 11 Section 3 Installing the MCU to the User System seeeeeeeesrrerreersreerrnrne 12 Section 4 Verifying peraliOn aicsaieshcesscencrssoademsrouanastoauersiepiacersadees renee 14 CCU INTO 5s ccsic nicieni a R aR a ea a sem eee A EA A anne 15 ii RENESAS Section 1 Configuration CAUTION Use an IC149 064 008 B5 socket manufactured by YAMAICHI ELECTRONICS Co Ltd for the FP 64A package IC socket on the user system Figure 1 shows the configuration of the HS3297ECH61H user system interface cable for the FP 64A package RENESAS LH emulator station Screws M2 0 x 12 mm and flat washers Screws M2 0 x 8 mm For fastening cable and flat washers head Cable head Figure 1 HS3297ECH61H User System
Download Pdf Manuals
Related Search