RCA RC926 User's Manual
Contents
1. Two Line Phone Operations If two separate lines are being used in a home only one line can operate through the Wireless Phone Jack System A single base and extension hook up will only operate that main phone line to which the base is connected Ground Fault Circuits In some cases ground fault interruption may interfere with the operation of this system It is recommended that the Wireless Phone Jack System not be set up or operated using ground fault circuitry e g bathrooms outdoor use etc Additional Help Is Available Thomson Consumer Electronics provides phone assistance to any one experiencing difficulties with the set up or usage of this sys tem If you have thoroughly read this guide and have performed the troubleshooting actions suggested on the previous page and still have problems with the performance of the system do not return it to your retailer Instead please call our Customer Service Center Wireless Phone Jack Customer Service Center 800 409 5111 10AM 7PM g Eastern Standard Time LIN ae 926 Manual V2 0 109643 6 10 99 1 39 PM Page Security Coding If your neighbor uses a Wireless Phone Jack System there could be some interference like static or background noise evident when you use a phone To help prevent this from occuring the Wireless Phone Jack System contains security codes which pro vide unique settings for your unit s operations To set your Security Code f2. LI ar 926 Manual V2 0 1J9643 6 10 99 1 39 PM Page 2 MIE One Year Limited Warranty Thomson Consumer Electronics warrants that for one year from date of purchase this product is free from defects in material and workmanship If the item is defective within that period return it at your expense to the dealer from whom it was purchased together with proof of purchase for replacement This warranty excludes defects or damage due to misuse abuse or neglect IN NO EVENT SHALL THOMSON CONSUMER ELECTRONICS BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER IN CONTRACT TORT OR NEGLIGENCE Some states do not allow limitations on how long an implied watranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may H also have other rights which vary from state to state For purchases in Canada refer to the Canadian warranty Wireless Phone Jack Help Line If you need additional set up help call our Help Line at 800 409 5111 nes 1994 Thomson Consumer Electronics Inc Trademark s Registered Printed in U S A 1J9643 Rev 8 94 Made in Malaysia Thomson Consumer Electronics Accessories and Components Business 2000 Clements Bridge Rd Deptford NJ 08096 2088 LIN ae
3. to the trouble shooting sec tion on next page Extension Unit Maise a s ae 2 LI ar 926 Manual V2 0 1J9643 6 10 99 1 39 PM Page Trouble Shooting Most difficulties associated with the Wireless Phone Jack System are due to improper installation If the steps below do not solve your difficulty remove both units from the electrical outlets remove all cords and reinstall making sure to follow instructions on the previous page Your situation system location characteristics of the home office can in some instances affect performance and occasional inter ference may be experienced Some static buzzing or humming at certain locations within the operating area is possible However if you experience unusual levels of noise follow the trouble shooting actions below PROBLEM ACTION No dial tone Check connections check outlet for power try new cords move base and or extension Static Move base and or extension halogen lamps Interference light dimmers and computer surge protectors can cause some static Can t set Move base and or extension Try security Security Code coding more than once see page 9 Can t dial out Decrease distance between units If problems continue call customer service Does not ring Decrease distance between units If problems continue call customer service No Dial Tone 1 Unplug both the base and extension unit Rapid Beeping from electrical outlets and di
4. 926 Manual V2 0 1J9643 6 10 99 1 39 PM Pagal ME res Digital Satellite System D916 W ireless Phone Jack System f r Pa i Hl 4 ff i al ded Ing f i i E T a The Wireless Phone Jack System works with most telephone line devices such as Answering machines Cordless Phones Speaker Phones Computer Modems Fax Machines eCorded Phones RCA Digital Satellite System Receiver TABLE OF CONTENTS Safety Precautions Getting Started Important N otes System Contents System Installation Trouble Shooting Things You Should Know Security Coding O perating W ith Digital Satellite System Computer Modem Additional Extensions W arranty Back Cover S a8 926 Manual V2 0 1J9643 6 10 99 1 39 PM Page y Important Safety Precautions CAUTION l DAJTE TO REGUS THE REA OF ELE OTR SHOR Go HoT ERASE orem Or Bo BOURSES ASE LE FART HACE PEER Sere TO GWUL PEO SERRE PERSE This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the system s enclosure that might be of sufficient magnitude to AN constitute a risk of electric shock Do not open the system s case This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying the system Read and follow precautions when installing and using the Wireless Phone Jack System Read and understand all instr
5. caller ID Phones e Be sure to plug Base unit two jacks on side in first before Extension unit one jack on side e If you cannot get a dial tone unplug both phone jacks and reset units following the section titled Trouble Shooting on page 7 e Itis very important that directions are followed in order In the event of a problem unplug both units remove all cords and start again aa ar 926 Manual V2 0 139643 6 10 99 1 39 PM Page ar Installation Follow the steps below to install your Wireless Phone Jack System NOTE To ensure proper performance it is important to install the Base Unit FIRST then install the Extension Unit Also ensure that both units are securely plugged into the wall outlets Base Unit 1 Plug one end of the provided telephone cord into either jack on the right side of the base unit and the other end into any exist ing wall phone jack 2 The phone previously used at that location should now be plugged into the extra jack on the side of the base unit 3 Now plug the base unit into an electrical outlet Wall Phone Jack Wall Outlet Telephone Cord Base Unit Extension Unit 4 Plug Wireless Phone Jack Extension unit into an electrical out let where you want a new phone jack 5 Plug telephone s line cord into the extension unit There should now be a dial tone when your phone is taken off the hook If there is no dial tone please refer
6. er lightning striking the tele phone or power lines can damage your system Lightning damage is not common Nevertheless if you live in an area that has severe electrical storms we suggest that you unplug the system during storms to reduce the possibility of damage S as 926 Manual V2 0 199643 6 10 99 1 39 PM Page Getting Started Unpacking Carefully remove units from packaging If there is any visible damage DO NOT attempt to operate the equipment Notify your dealer or shipping carrier immediately Keep this guide for future use System Contents e Base Unit The base unit has two modular telephone jacks on the right side a recessed security code button and a green indicator light e Extension Unit The extension unit has one jack on the right side a recessed security code button and a green indicator light This is the unit that can be moved from location to location to create a phone jack in an electrical outlet e Telephone Cord 6 A 6 ft telephone cord is provided to connect the base unit to the existing wall phone jack If this length is insufficient a longer cord may be purchased ask for GE Phone Hook Up product TP230 Important Notes On Operation Do not plug phone jacks into power strips or surge protectors e Extension phone jack does not operate during a power outage e Phone Jack System can only be used for one phone line e Phone Jack System does not operate with
7. iver hook up After installing the Wireless Phone Jack base unit see page 6 follow the picture and instructions below to install the extension unit to the RCA Digital Satellite System Receiver 1 Plug Extension Unit into an electrical outlet 2 Plug one end of the phone line cord provided into jack on extension unit 3 Plug the other end of the phone line cord into back of Digital Satellite SystemReceiver phone line jack Once your Wireless Phone Jack System base and extension units are installed you can expand your system with additional extensions to add more phone jacks Extension units are sold separately ask for Digital Satellite System model D910 or RCA model RC920 Back of Digital Satellite System Receiver Computer Modems After installing the base unit see page 6 follow these steps to install the extension unit to a computer modem 1 Plug Extension Unit into an electrical outlet 2 Plug telephone line cord from the computer modem into jack side of Wireless Phone Jack Extension Unit 3 Computer modem is now ready to operate Note The maximum baud rate for the Wireless Phone Jack is 14 400 Best results however will be experienced at 9 600 Under certain circumstances where static is present in your telephone line the Wireless Phone Jack may not filter or remove such static This condi tion can affect computer modem performance If your computer modem has an adjustable baud and you are experiencing tr
8. n disconnect your service The phone company tries to notify you in advance If advance notice is not practical the tele phone company notifies you as soon as possible and advises you of your right to file a complaint with the FCC LIN ae 926 Manual V2 0 109643 6 10 99 1 39 PM Page FCC Part 68 amp Class B Notices Your wireless phone jack system complies with Part 68 of FCC Rules You must upon request provide the FCC registration number and the REN to your telephone company These numbers are shown on the label on the base unit This equipment complies with the limits for a Class B digital device as speci fied in Part 15 of FCC Rules These limits provide reasonable protection against radio and TV interference in a residential area However your equipment might cause TVor radio interference even when it is operating properly To eliminate interference you can try one or more of the following corrective measures e Reorient or relocate the receiving antenna e Increase the distance between the system and the radio or TV e Use outlets on different electrical circuits for the equipment and the radio or TV Read the Troubleshooting section of this manual for directions on remedy ing the problem Lightning Your wireless phone jack system has built in protection circuits to reduce the risk of damage from surges in telephone line These protection circuits meet or exceed the FCC requirements Howev
9. ollow the steps below Once set these codes are locked in the system allowing you to move the units to a new location within your home without resetting In addition the codes will be protected in memory even during power outages and should hold up to 2 hours Setting The Security Code 1 Complete the unit installation steps on page 6 Make sure the phones connected to the units are on their hook and the units are plugged into the electrical outlet 2 Find the small recessed coding button on the right side of each unit a Using a pen or pencil depress the button on the base unit ran The green light on the base will light up To Wall Jack To Phone b Next press the button on the extension unit s Allow no more than 5 minutes to elapse between base and exten sion s button depression If the extension is able to establish a compatible code its light will flash once If the extension is unable to find a compatible code the light will continue to flash It is possible that you will have to depress the extension button a couple of times before it flashes only once 3 Once codes are set lift the extension phone off the hook and replace The green light on the base unit should not be lit LIN ae 926 Manual V2 0 139643 6 10 99 1 39 PM Page LO YY RCA Digital Satellite System The Wireless Phone Jack System allows you to add a phone jack near your TV for easy RCA Digital Satellite System Rece
10. ouble adjust the baud to a lower speed In many cases this will improve performance 10 aa ey 926 Manual V2 0 139643 6 10 99 1 39 PM Page w1 LY Ordering Additional Extension Units An unlimited number of extension units can be added to your Wireless Phone Jack System once the base unit is installed To purchase additional Extension Units for your Wireless Phone Jack System contact your local dealer and ask for model number RC920 If no dealer is available you may purchase additional units by calling the toll free number listed below and placing an order by phone Please allow 2 weeks for delivery Description Model Price Qty Extension Unit RC920 49 95 Sales Tax We are required by law to collect the appropriate sales tax for each individual state county and locality to which the merchandise is being sent Total Merchandise Order Shipping and Handling oO Total Amount Due Price is subject to change without notice ORDERING BY PHONE Have your Visa or MasterCard ready and call the toll free num ber listed below This number should only be used to place orders for Wireless Phone Jack extension units See the next page for Help Line assistance 1 800 338 0376 ORDERING BY MAIL Provide your name address phone number and a check or money order for your unit s and mail to RCA Accessories PO Box 8419 Ronks PA 17573 Include this completed form with your order i1
11. sconnect all cords from both units 2 With the tip of a pencil press the security button the recessed black button directly below the green light on the side of both units and hold it for 5 seconds on the base unit first while unit is unplugged Repeat same procedure with the extension unit while unit is unplugged 3 Always reconnect the base unit to the elec trical outlet and telephone cord first then connect the extension s 4 You will not need to reactivate the security buttons again unless you experience inter ference from a neighbor s telephone LIN ae 926 Manual V2 0 139643 6 10 99 1 39 PM Page 3 Mie Things You Should Know The following list of situations is provided to inform you of things that you may encounter when using the system It 1s intended to help you get the best performance possible from your Wireless Phone Jack System Power Outages During an AC power failure only the telephone plugged into the base unit operates Additional Extension Units You can add extension units to expand your system Ask for the compatible extension Model Number RC920 or Digital Satellite System Model Number D910 Simply install the exten sions by following Steps 4 and 5 on page 6 When you install more than one extension you can only use one extension at a time If you lift the receiver on a phone connected to an extension unit while another unit is being used you hear a busy signal
12. spilled into the system If the system has been exposed to rain or water If the system does not operate normally by following the operating instructions E Ifthe system has been dropped or the cabinet has been damaged F If the system exhibits a distinct change in performance DOWD e Avoid using a telephone other than a cordless phone during an elec trical storm There is a remote risk of electric shock from lightning e Do not use the telephone to report a gas leak in the area of the leak FCC Information We designed your Wireless Phone Jack System to conform to federal reg ulations and you can connect it to most phone lines However each device you connect directly to the phone line draws power from it This power draw is the device s ringer equivalence number or REN The REN is shown on the base unit s label If you connect more than one phone or other device directly to the phone line add up all the RENs If the total is more than five or three in rural areas your phones may not ring If ringer operation is impaired remove a device from the line Note Your wireless phone jack system has an REN of 0 7B and so does not affect your phones ability to ring Also the phone you plug into the extension unit does not place any load on the telephone line However the phone you plug into the base unit does affect the total REN If your wireless phone jack system causes problems on the phone line the telephone company ca
13. uctions e Follow all warnings and instructions marked on the system and in this guide e Unplug this system from the wall outlet before cleaning Do not use liq uid or aerosol cleaners Use a damp cloth for cleaning Do not use this system near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or in or near a swimming pool e This system should never be placed near or over a heat radiator or reg ister This system should not be placed in a built in installation unless proper ventilation is provided e This system should only be operated from the type of power source indicated in this guide and on the system s label If you are not sure of the type of power supplied to your home or building consult your local power company e Never spill liquid of any kind on the system e To reduce the risk of electric shock do not disassemble this system but take it to a qualified service facility when service or repair is required LIN ae 926 Manual V2 0 199643 6 10 99 1 39 PM Page 3 Safety Precautions Continued e Opening or removing the covers might expose you to dangerous volt ages or other risks Incorrect reassembly can cause electric shock when the system is subsequently used e Unplug the system from the wall outlet and refer servicing to a quali fied service facility under the following conditions When the AC plug is damaged If liquid has been
Download Pdf Manuals
Related Search