RCA JOYTECHTM AV CONTROL CENTER 2 User's Manual
Contents
1. is connected correctly and that the power is e Avoid placing this product near extreme temperatures or humidity switched on e Do not submerse or allow this product to come into contact with water Use in dry ocations only e If the Power Standby Button at the front of the AV Control Center 2 is red then the unit is in standby mode Switch on by either pressing the Power Standby e An adult should supervise young children when using this product Button at the front of the AV Control Center 2 or by pressing the Standby Button e Use of any attachment or accessory with this product not recommended or sold by on the Remote Controller The Power Standby LED will illuminate green when the JOYTECH may result in risk of fire electrical shock or injury to persons or product power is ON Do not clean any parts with alcohol cleaning solutions containing alcohol or strong abrasives Use a soft cloth and a little water THE AV CONTROL CENTER 2 IS ON BUT DO NOT SEE A PICTURE FROM MY TV e Tampering with this product will invalidate your JOYTECH warranty Ensure that the AV Control Center 2 is connected correctly to your television and that the correct video input on your TV has been selected Refer to your TV IMPORTANT HEALTH WARNINGS instruction manual for more information Photosensitive Seizure Warning e Make sure each AV device is connected to the AV Control Center 2 correctly A very small percentage of people may experience a se2. AV_CONTROL_V1_ENG qxq 22 11 04 33 am Page 1 AV CONTROL CENTER 2 USER GUIDE VERSION 1 0 AV_CONTROL_V1_ENG qxq 22 11 04 11 33 am Page 2 WELCOME Thank you for purchasing the JOYTECH AV Control Center 2 Before connecting the AV Control Center 2 please familiarize yourself thoroughly with this User Guide so that you fully understand the setup procedure and functions of the product CONTENTS CHECK THAT YOU HAVE THE FOLLOWING ITEMS AV Control Center 2 SCART Cable S Video Audio Cable Composite Audio Cable Ethernet Cable AC Power Adapter Remote Controller SCART Adapter User Guide ENGLISH 00 00 DEUTSCH 00 00 FRAN AIS 00 00 SVENSKA O00 00 OoOonouo RoW HOLLANDS O0O00 00 AV CONTROL CENTER LAYOUT ITALIANO O00 00 FRONT VIEW ESPANOL 00 00 Input Channel Display Input Selector PORTUGUES 00 00 Display Settings Controls Input 6 IR Remote Receiver Power Standby Press to turn the AV Control Center 2 power On and Off The Power Standby LED will illuminate green when the power is on and red when the unit is in standby mode Input Channel Display Each Input Channel name can be programmed in order to identify the AV device that is connected to each Input Channel AV_CONTROL_V1_ENG qxq 22 11 04 11 33 am Page 4 Input Selector Press to page through and select the requir
3. CA connector to a white RCA Input Socket and the Composite Video and Stereo Audio red audio RCA connector to a red RCA Input Socket Alternatively you can connect the RCA leads to the SCART Adapter and follow the instructions for SCART connections Connect the S Video connector to a 4 pin DIN Input Socket the left audio connector to a white RCA Input Socket and the right audio connector to a red RCA Input Socket S Video and Stereo Audio Connect the SCART connector to a SCART Input Socket Note SCART will normally carry both the video and stereo audio signals This is the most versatile AV connection and is recommended wherever possible Connect the SCART connector to a SCART Input Socket and the digital optical connector to the SCART and Digital Optical Digital Optical Socket in the same Input Channel Remember to remove the dust cap and store safely for when Optical Socket is not in use Connect the Ethernet cable to an Ethernet Input Socket Note Your modem must either be a DSL or a Ethernet cable modem Do not use the AV Control Center 2 with a standard telephone modem IMPORTANT Before connecting your modem to the AV Control Center 2 make sure you have a valid account Connect a composite video and mono stereo audio cable to the SCART Adapter and connect to any SCART Input Socket SCART Adapter IMPORTANT Each input connection will only correspond to the matching output connec
4. Ensure that all AV devices that are connected to the AV Control Center 2 and not e Sit further away from the screen being viewed are switched OFF as certain devices emit strong signals which can Use a smaller TV screen interfere with the AV device being viewed e Play in a well lit room e Check that the connections between AV devices are secure e Do not play when you are drowsy or fatigued If you or any of your relatives have a history of seizures or epilepsy consult a doctor before BATTERY CARE playing Incorrect use of batteries can result in battery leakage or explosion When using We also advise you to take regular breaks of 15 minutes every hour batteries be sure to follow these instructions e Make sure that the plus and minus terminals of the batteries are inserted in the correct directions e Do not mix old and new or different types of batteries If you are experiencing a problem with this product contact the JOYTECH Product Helpline on e Do not attempt to recharge non rechargeable type batteries 44 O 800 38 99 647 FREEPHONE UK ONLY e Remove the batteries when the product will not be used for an extended period of time or visit our website at www joytech net to obtain localised helpline numbers e If the battery has leaked be sure to carefully remove all residue before inserting new Design and specifications are subject to change without notice batteries Dispose of this product or products
5. contained in this pack in accordance with local and national disposal regulations
6. e first Input Indicator to illuminate will be Input 1 You can select other Inputs by pressing the SELECT Button located on the front of the AV Control Center 2 or by using the Remote Controller PROGRAMMING THE INPUT CHANNEL DISPLAY For easy identification of the AV equipment connected to the AV Control Center 2 it is possible to name each of the 6 inputs on the Input Channel Display For example should you wish Input 1 to read DVD and Input 2 to read GAME follow this setup procedure 1 Using the Select Button on the front panel select the desired Input Channel 1 6 that you would like to name 2 Open the access cover on the front of the AV Control Center 2 3 Press the SET Button to begin to change the name The first character on the Input Channel Display will begin to flash 4 Use the and buttons to cycle through all the available characters When the desired character is displayed press the SET Button to select the character and move to the next Repeat the process until you have achieved your desired name 5 Once you have selected the 5th character the name will be stored and assigned to your chosen Input Channel Repeat the above procedure for each Input Channel you wish to name AV_CONTROL_V1_ENG qxq 22 11 04 11 33 am Page 8 TROUBLESHOOTING CAUTION THE AV CONTROL CENTER 2 FAILS TO TURN ON e Do not remove this product when the console power is ON e Ensure that the AC Power Adapter
7. ed Input Channel IR Remote Receiver For use with the Remote Controller Display Setting Controls These controls are used to program the Input Channel names displayed on the LCD Display Input 6 Primarily used for temporary connection of camcorders and other AV devices to the AV Control Center 2 REAR VIEW AC 9V IN 0 0005 0000466690000 00006 00005 E N Input 4 Output The AV Control Center 2 has a total of 6 Input Channels Input 6 is located on the front panel and Inputs 1 to 5 are located on the rear panel Each Input Channel comprises of either 5 or 7 Input Connectors figure 1 Figure 1 Composite video yellow Left Audio white Right Audio red S Video Optical Audio REMOTE CONTROLLER You can page through each Input Channel by pressing the Select Button on the front panel of the AV Control Center 2 Alternatively you can select each Input Channel by using the Directional or Numerical Buttons on the Remote Controller The Standby Button located on the Remote Controller allows the AV Control Center 2 to be switched from on to standby mode Standby Directional Buttons Numerical Buttons When inserting new batteries into the Remote Controller take care to observe the correct polarity Requires 2 x AAA LRO3 alkaline batteries EXAMPLE OF A TYPICAL SETUP USING THE AV CONTROL CENTER 2 The AV Control Center 2 has been designed to connect up to 6 separate AV devices and output t
8. he Audio Video signal to a single input on the TV Hi Fi Each device can be selected independently of each other Once a device has been connected there is no need to remove any of the cables when selecting an input Figure 2 shows a typical AV set up using the AV Control Center 2 Figure 2 DVD Player satellite receiver 28 PlayStatione2 stereo Hi Fi FA camcorder NOTE The devices connected in this illustration are for reference only Any suitable device may be connected to the Input Channels AV_CONTROL_V1_ENG qxq 22 11 04 11 33 am Page 6 WHICH CABLE DO I USE SETUP INSTRUCTIONS Depending on the type of output available from your AV device use the most suitable cable connection from the Input Connection Table below NOTE The AV Control Center 2 is supplied with a standard Cable Pack You may require additional cables to set up your chosen AV devices OUTPUT FROM YOUR AV DEVICE HOW TO CONNECT Connect the yellow video RCA connector to a yellow RCA Input Socket and the white audio RCA connector to a white RCA Input Socket Alternatively you can connect the RCA leads to the SCART Adapter and follow the instructions for SCART connections Composite Video and Mono Audio Connect the yellow video RCA connector to a yellow Input RCA Socket the white audio R
9. izure when exposed to certain visual images including flashing lights or patterns that may appear in video games Even people who e Ensure you have selected the correct Input Channel on the AV Control Center 2 have no history of seizures or epilepsy may have an undiagnosed condition that can cause these photosensitive epileptic seizures while watching video games THE AV CONTROL CENTER 2 IS ON BUT THERE IS NO SOUND FROM MY TV These seizures may have a variety of symptoms including lightheadedness altered vision eye ore or face twitching jerking or shaking of arms or legs disorientation confusion or momentary Check that the AV device is connected to the AV Control Center 2 using EITHER the loss of awareness Seizures may also cause loss of consciousness or convulsions that can left and right Stereo Audio RCA Input Sockets SCART or Digital Optical Inputs lead to injury from falling down or striking nearby objects e Make sure that the volume settings on your TV and AV devices are set correctly Immediately stop playing and consult a doctor if you experience any of these symptoms Remember that the S Video connectors do not transmit an audio signal Parents should watch for or ask their children about the above symptoms children and teenagers are more likely than adults to experience these seizures WHEN VIEW A DEVICE I GET BACKGROUND INTERFERENCE Taking the following precautions may reduce the risk of photosensitive epileptic seizures
10. tion except Input 6 See below For example a SCART cable attached to SCART Input 1 can only be viewed via the SCART Output Socket and cannot be displayed via the S Video Composite Video or Stereo Audio RCA Output Sockets INPUT 6 The Composite Video and Stereo Audio RCA Input Sockets on Input 6 link directly to both the corresponding Output Sockets and the SCART Output Socket located on the rear panel of the unit The S Video Input Socket on Input 6 links directly to the S Video Output Socket located on the rear panel of the unit 1 Connect the AC Power Adapter to the AC QV IN located on the rear panel of the AV Control Center 2 2 Connect the desired output of the AV Control Center 2 to your television using the SCART S Video or RCA Phono Cable supplied Note If you are using the S Video Cable as the video output you will need to connect the RCA Phono Cable White and red to the TV Hi Fi in order to receive audio S Video connectors do not carry an audio signal 3 Connect your AV devices to inputs 1 to 5 ensuring the power is switched off on all devices before connecting 4 Switch on your TV and select the External input channel Refer to your television user guide for more details 5 Switch on the AV Control Center 2 either by pressing the Power Standby Button on the front of the AV Control Center 2 or by using the Remote Controller The Power Standby LED will illuminate green when the unit is on 6 Th
Download Pdf Manuals
Related Search