RCA 7114-2BSGA User's Guide
Contents
1. 2 Plug one end of the telephone line cord into the TEL LINE jack on the back of the base and the other end into a modular jack Dia 1A Oc O B00 3 Plug the AC power converter into the electrical outlet and the DC connector into the jack on the back of the base 4 Place the handset in the base cradle The charge in use indicator turns on verifying the battery is charging 5 Allow the phone to charge for 16 hours prior to first use If you don t properly charge the phone battery performance is compromised CAUTION To reduce risk of personal injury fire or damage use only the power adaptor Manufacturer SKY WILL MODEL NO SP060 0500U 100 240Vac 6V 500mA listed in the user s guide This power adaptor is intended to be correctly orientated in a vertical or floor mount position There are a variety of programmable menus available for the base and cordless handset While the unit is in STANDBY mode press MENU OK on the base cordless handset to enter the program mode There provide all the system settings Change them so that make the DECT phone work in your favorite status In the program mode MENU OK is used frequently as entering menu items and storing any update Review lt or gt A or Y are for selecting items Digit keys 0 9 are used to input new values The program mode will exit and return to STANDBY in even of timeout 30s or the EXIT key is depressed Note base and cordless handset2. DECT 6 0 Corded amp Cordless Speakerphone with Answering Machine User s Guide Please read this manual before operating product for the first time Visit the RCA web site at www rca4phones com Model 7114 Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68 FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating among other information the US number and Ringer Equivalence Number REN for the equipment You must upon request provide this information to your telephone company The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed 5 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be conn
3. Pick up the phone during the incoming message if wanted 5 Review your messages from a remote location SET UP THE ANSWERING MACHINE Personalize your answering machine by recording a greeting for callers If you Don t record your greeting callers hear the default greeting We are unavailable to take your call Please leave a message thank you for your calling RECORD THE GREETING When recording the greeting you should be about 6 inches from the unit reduce as much background noise as possible 1 Prepare your greeting i e Hi this is your name sorry can t answer your call now so please leave your contact information and a brief message after the tone will call you back Thanks for calling 2 Press amp hold the ANNOUNCE key the unit announces record announcement after the tone and the screen display TO RECORD After the one recoding greeting no longer than 1 minute 3 Release ANNOUNCE key when you finish The phone announces Your announcement is plays back your recording 4 To go back to default greeting after you ve made recorded a greeting press ANNOUNCE and release it when you hear the tone or press and hold DELETE when the greeting is playing REVIEW THE GREETING Press and release the ANNOUNCE button to review your outgoing greeting AUTO DISCONNECT Auto disconnect is a feature that tells the unit to stop playing the greeting or recording a message when an extension phone is pickup if
4. e Products that have been serviced by an unauthorized servicer e Products purchased or serviced outside the USA or Canada e Acts of nature such as but not limited to lightning damage Limitation of Warranty e THIS LIMITED WARRANTY IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED NO VERBAL OR WRITTEN INFORMATION GIVEN BY SUPREME POWER USA LLC ITS AGENTS EMPLOYEES RETAIL DEALERS OR INDEPENDENT CONTRACTORS SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY e REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER SUPREME POWER USA LLC SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE How state law relates to this warranty Some states do not allow the exclusion nor limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or
5. STANDBY mode press MENU until deregistration appears 2 Press lt or to select which handset to be deregistered 3 Press OK to start deregistration and jump to the next menu item DEFAUTL gt NO YES 4 While unit is in STANDBY mode press MENU until default NO appears 5 Press lt lt or gt gt to select NO or YES 6 If select YES press OK to default all settings but message caller log and phone book In handset menu items sequence ALARM HANDSET SETUP SET LANGUAGE HANDSET NAME RINGER TONE RINGER VOLUME AREA CODE REGISTRATION DEREGISTRATION DEFAULT SETTING CONTRAST ALARM 1 While unit is in STANDBY mode double click at MENU Alarm ON OFF appears and asks for choice 2 Press A or W to select ON and OFF 3 To disable ALARM please select OFF and press OK to confirm 4 To enable ALARM please select ON and press OK to confirm Then will require to SET ALARM 5 Use dial keypad 0 9 input desired alarm time and AM PM Press OK to confirm There shall come ONCE and DAILY selection A or W to select it and press OK to save HANDSET SETUP SET LANGUAGE 1 While unit is in STANDBY mode press MENU and then press A or W to select HANDSET SETUP 2 Press OK to enter and A or W to select SET LANUAGE 3 Press OK again to start SET LANUAGE 4 Press A or W to select choice 5 Press OK to save it and return to menu items HANDSET NAME 1 While unit is in STANDBY mode press MENU and then
6. charge cradles battery packs and covers than shown above For Model 7114 4 there will be THREE cordless handsets charge cradles battery packs and covers than shown above Telephone Jack Requirements To use this phone you need an RJ11C type modular telephone jack which might look like the Wall plate one pictured here installed in your home If you O don t have a modular jack call your local phone Modular a company to find out how to get one installed telephone A line jack o Installation Digital Security System Your cordless phone uses a digital security system to protect against false ringing unauthorized access and charges to your phone line INSTALLATION NOTE Some cordless telephones operate at frequencies that may cause or receive interference with nearby TVs microwave ovens and VCRS To minimize or prevent such interference the base of the cordless telephone should not be placed near or on top of a TV microwave ovens or VCR If such interference continues move the cordless telephone farther away from these appliances Certain other communications devices may also use the 1 9GHz DECT frequency for communication and if not properly set these devices may interfere with each other and or your new telephone If you are concerned with interference please refer to the owner s manual for these devices on how to properly set channels to avoid interference Typical devices that may use the 1 9GHz DECT frequency for comm
7. cordless handset is off the hook in talk mode automatically hangs up the phone RINGER VOLUME While unit is in STANDBY mode not in talk mode For base Press vol vol to enter ringer volume setting Continue vol vol to select OFF 1 5 for base ringer volume For cordless handset ease see ringer volume in telephone setup section U FLASH Use the FLASH on the base or cordless handset to activate custom calling services such as call waiting or call transfer which are available through your local phone company USING TEMPORARY TONE DIALING If you have pulse rotary service and want to access customer calling services that require tone dialing such as telephone banking and long distance services use this feature to temporarily change from pulse to tone service After dialing the telephone number and connecting to the customer calling service 1 Press and release TONE 2 Proceed with conversation 3 When you hand up the phone automatically returns to pulse dialing mode Paging handset This feature helps you locate a misplaced handset Press the INT on the base the display shows HS NUMBER Input 1 4 that presents the misplaced handset The destination handset rings for one minute until you press EXIT on the base to cancel Mute To have a private off line conversation use the mute feature the party on the other end of the line cannot hear you but you can still hear them 1 Press the MUTE o
8. new ones from your dealer No display e Ensure the batteries are charged e Ensure there are power and phone connections Bad audio crackles echo etc The handset is nearly out of range Move it closer to the base station e The phone receives interference from the nearby electrical appliances Move the base station away from them e The phone is at a location with thick walls Move the base away from them The handset does not ring Ensure the handset ringtone is turned on The caller ID does not display e The service is not activated Check with your service provider e The caller s information is withheld or unavailable The handset loses connection with the base or the sound is distorted during a call eeDisconnect the power supply from both the handset and base station Try again after 1 minute Warranty Assistance Your sales receipt will be required to demonstrate proof of purchase in order to validate your warranty eligibility You may want to attach either the original or a photocopy of your sales receipt to this booklet for future reference If this product was received as a gift it is suggested you jot down the date of gift receipt as this information will be valuable should service be required during the warranty period If the equipment is causing harm to the telephone network the telephone company may require that you disconnect the equip ment until the problem is resolved Purchase Date or Date
9. press A or select HANDSET SETUP 2 Press A or W to locate at HANDSET NAME 3 Press OK to enter and dial keypad 0 9 to edit name 4 Press OK to save and return to menu items RINGER TONE 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or to locate at RINGER TONE 3 Press OK to enter and A or to select it 4 Press OK to save and return to menu items RINGER VOLUME 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP Note You may use a one touch key to enter ringer volume press directly 2 Press A or W to locate at ringer volume 3 Press OK to enter and A or to select level OFF 1 5 4 Press OK to save and return to menu items AREA CODE 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or W to locate at AREA CODE 3 Press OK to enter and dial keypad 0 9 to input new code 4 Press OK to save and return to menu items REGISTRATION 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or W to locate at registration 3 Press OK to enter and A or to select YES or NO 4 If select YES and then press MENU to start registration Also you shall let base enter registration mode in parallel see base registration Note max 4 handsets can be registered with a base DEREGISTRATION 1 While unit is in STAN
10. special disposal instructions SAVE THESE INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A CAUTION TO REDUCE THE f THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD DO NOT EXPOSETHIS PRODUCT TO RAIN OR MOISTURE BACK NO USER WARNING SIGN WARNING SIGN SERVICEABLE PARTS INSIDE f ALERTING YOU OF ALERTING YOU OF J REFER SERVICING TO IMPORTANT l QUALIFIED SERVICE INSTRUCTIONS PERSONNEL ACCOMPANYING D VOLTAGE INSIDE UCT THE PRODUCT THE PRODI SEE MARKING ON BOTTOM BACK OF PRODUCT IMPORTANT Because cordless phones operate on electricity you should have at least one phone in your home that isn t cordless in case the power in your home goes out Before You Begin Parts Checklist for 7114 2 Make sure your package includes the items listed here A B c jefe ae aree O sore lf EL ad S Base Handset 5 nea N men EE Battery Base compartment Desktop cover pedestal Handset AC Power battery pack adaptor Handset rd Telephone line cord For Model 7114 2 there will be ONE cordless handset charge cradle battery pack and cover than shown above For Model 7114 3 there will be TWO cordless handsets
11. the greeting continues to play after picking up an extension phone press PLAY STOP PLAY MESSAGES Messages can only be played back through the speaker use PLAY STOP button to play messages The unit first plays new messages in order received If there are no messages the unit announces you have no message if there are no new messages the old messages are played back When playing messages the message number and date time stamp display 1 To play messages press and release PLAY STOP 2 To stop playback press and release PLAY STOP again 3 To replay the previous message press the lt lt button 4 To play skipped messages press and release gt gt button ERASE A SINGLE MESSAGE Press and release DELETE while the message is playing The unit erases the current message and announces message erased ERASE ALL MESSAGES You can erase all old messages leaving new messages and Caller ID information While the unit is in STANDBY mode hold down DELETE button until the unit announces all old messages erased NOTE New messages cannot be erased in this way to erase new messages play the message and then press DELETE during play back MEMORY FULL When the unit s memory is full possible 45 minutes of messages recorded it answers after 10 rings and announces Memory is full A 20 seconds waiting period follows When you enter your security code You can then play your messages and erase some of them to restore mem
12. 9 calls on the base set amp 35 calls on the cordless handset you received so that you can see who called while you were unavailable When the 100the call on the base set or 36th call on the cordless handset is received the oldest caller ID record 1st call is automatically deleted You will find the number of missed calls NEW CALL xx in cordless handset And Xx at the right top corner of LCD in base while in STANDBY mode Unanswered call f tells you of missing call Reviewing call records As calls are received and stored you will find total call and total new call 1 The unit should be in on hook state 2 Review A V or lt gt to select the caller ID record 3 The corresponding caller ID s content should be displayed Note New call e will turns ON if the call is unanswered and not reviewed before Delete caller ID While reviewing caller ID press DELETE to remove it and the next record will show Note In cordless handset need to press DELETE one more time to confirm removal for every caller ID Delete all caller IDs While reviewing caller ID press and hold DELETE until DELETE ALL shows press DELETE again to confirm A confirmation tone will be heard Dialing back When reviewing caller ID records you can dial back a displayed number Press Format key Note If pickup phone shows in the display no other change to the number can be made such as adjusting the area code the information sent from the teleph
13. D number to memory location 3 While reviewing CID number press STORE 4 Input location number 0 9 A B C 5 Press STORE to save with a confirmation tone Storing redial number to memory location For base 1 While unit is in STANDBY mode press STORE and then input location 0 9 A B C 2 Press STORE again to start number edit 3 Press REDIAL to show the redial number 4 Press STORE to save it For handset Nothing special but different number and name edit orders Deleting memory location While memory is in review press DELETE to delete it and a confirmation Tone generates Note There is a little difference between operation in base and cordless handset Cordless handset needs confirmation of DELETE Base directly takes effect without pressing DELETE again Reviewing memory location While unit is in STANDBY mode press STORE and then input location number 0 9 A B C or Review A W or lt gt to change memory location Dialing from memory location From TALK mode 1 Make sure the phone is ON in talk mode 2 Press STORE 3 Input your desired memory location 4 The location number will be automatically dialed out From STANDBY mode While reviewing memory location in base pickup handset or press SPEAKER icon or While reviewing memory location in cordless handset press TALK icon The displayed number will be automatically dialed out Caller ID IMPOR
14. DBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or W to locate at DEREGISTRATIO 3 Press OK to enter and A or W to select YES or NO 4 Press OK to confirm it and return to menu items DEFAULT SETTING 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or W to locate at default setting 3 Press OK to enter and A or to select YES or NO 4 Press OK to save and return to menu items Note default all settings but not call log and phone book CONTRAST 1 While unit is in STANDBY mode press MENU and then press A or select HANDSET SETUP 2 Press A or W to locate at CONTRAST 3 Press OK to enter and A or to select level 1 5 4 Press OK to save and return to menu items CALL OPERATION Receiving a call with speakerphone handset 1 When the phone rings press the SPEAKER s on the base or pick up handset and speak normally at a minimum distance of 8 9 inches into the built in microphone if in speakerphone model 2 Adjust listening volume by vol vol 3 To end the call press the SPEAKER s4 again if in speakerphone mode or put back handset to the cradle again Making a call with speakerphone handset 1 Press the SPEAKER sf or pickup handset and wait for a dial tone 2 Dial the number using a memory dial number if desired the number shows in the display or Dial the number and then press SPEAKER or pickup hand
15. Received as Gift ame of Store For instructions on how to obtain warranty service you may call Customer Care at 1 877 722 4908 or you may visit our website at www rca4phones com If you prefer you may write to us at Supreme Power USA LLC PO Box 501045 ndianapolis IN 46250 1045 Please do not send products to this address as it only adds delays in service and may result in lost or damaged product This PO BOX is for written communication only f the equipment is causing harm to the telephone network the telephone company may require that you disconnect the equipment until the problem is resolved Limited Warranty What your limited warranty covers e Defects in materials or workmanship For how long after your purchase e One year from date of purchase Please retain your sales receipt as that will act as your proof of purchase in order to validate warranty status What we will do e Provide you with a new or at our option a refurbished exchange unit of same or similar model The exchange model is under warranty for the remainder of the original product s one year warranty or 90 days from the date the replacement product was shipped to you whichever is longer How to get service e Call Customer Care at 1 877 722 4908 Please have your product with you and please have your model number and date code available when calling us The model number and date code can be found on the underside of the base unit If you are w
16. TANT In order to use this unit s Caller ID features you must subscribe to either the standard Name Number Caller ID service or Call Waiting caller ID Service To know who is calling while you are on the phone you must subscribe to Call Waiting Caller ID Service This unit receives and displays CID information transmitted by your local telephone company this information can include the phone number date and time name Call Waiting caller ID Provided you subscribe to call waiting caller ID service from your phone company if you receive on incoming call and you are already on the phone a beep indicates the presence of a call waiting call on the line Only the handset that is in use at the time of the call will display and store the call waiting caller ID information When you hear the call waiting beep press the FLASH on the base or cordless handset to put the current call on hold and answer the incoming call Press the FLASH again to return to the original call Receiving CID records When you receive a call caller ID information is transmitted by the phone company to your telephone between the first and second ring The caller ID information appears on your phone s display while the phone rings Giving you a chance to monitor the information and decide whether or not to answer the call Storing CID records In CID memory f you are not at home or cannot answer your telephone s caller ID memory stores the data for the most recent 9
17. area code appears 2 Use dial keypad 0 9 to input your desired codes lt or gt to move cursor 3 Press OK to confirm the update and jump to the next menu item gt TONE PULSE 4 While unit is in STANDBY mode press MENU until gt tone pulse appears 5 Press lt or gt to change dial mode 6 Press OK to confirm the update and jump to the next menu item SET THE YEAR 1 While unit is in STANDBY mode press MENU until set the year appears 2 Press lt or gt to change item among set the year set time date and AM PM 3 Use dial keypad 0 9 to input values 4 Press OK to confirm the update and jump to the next menu item SET LANGUAGE 1 While unit is in STANDBY mode press MENU until gt ENG FRA ESP appears 2 Press lt or gt to change choice 3 Press OK to confirm the update and jump to the next menu item REGISTER ON gt OFF 1 While unit is in STANDBY mode press MENU until REGISTER gt ON OFF appears 2 Press lt or gt to change choice 3 If select OFF press OK to skip the function and jump to the next menu item 4 If select ON press OK to issue it and enter registration mode Note For cordless handset please also enter register mode see Handset menu 5 If successes a confirmation tone from handset will be heard Both handset and Base shall exit to STANDBY mode Note A base can be register up to 4 cordless handsets DEREGISTRATION 1 While unit is in
18. bring a complaint to he Commission pursuant to procedures set forth in Subpart E of Part 68 FCC Rules and Regulations The telephone company may make changes in its communications facilities equipment operations or procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations f these changes are expected to affect the use or performance of your elephone equipment the telephone company must give you adequate notice in writing to allow you to maintain uninterrupted service Interference Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation Privacy of Communications may not be ensured when using this product I
19. button then input command code list above During the remote access press EIXT button to stop and return to STANDBY mode MESSAGE INDICATORS Xx MESSAGE messages count Xx CALLS call log count UNKNOWN NUMBER the service area is not linked to yours UNKNOWN NANE the name information for the number is not available BLOCKED the caller is registered as private number NUMBER START END the end of call log record NO DATA absence of caller ID data memory list Frequently asked questions The signal icon blinks on the screen e The handset is out of range Move it closer to the base station e If the handset displays UNREGISTERED register the handset Tip e For more information see Registration on the Advanced settings section If I fail to register the additional handsets to the base station what do do Your base memory is full Un register the unused handsets and try again No dialing tone e Check your phone connections e The handset is out of range Move it closer to the base station No docking tone e The handset is not placed properly on the base station charger e The charging contacts are dirty Disconnect the power supply first and clean the contacts with a damp cloth The handset on the charger does not charge e Ensure the battery pack is inserted properly e Ensure the handset is placed properly on the charger The battery icon animates when charging e Batteries are defective Purchase
20. e the equipment Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This transmitter must not be co located or operated in conjunction with any other antenna or transmitter For body worn operation this phone has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied with this product Use of other accessories may not ensure compliance with FCC RF exposure guidelines Information for DECT Product This telephone is compliant with the DECT 6 0 standard which operates in the 1 92GHz to 1 93GHz frequency range Installation of this equipment is subject to notification and coordination with UTAM Any relocation of this equipment must be coordinated through and approved by UTAM UTAM may be contacted at 1 800 42 9 8826 DECT e INTERFERENCE FREE COMMUNICATION Industry Canada I C Notice This product meets the applicable Industry Canada technical specifications Le pr sent materiel est conforme aux specifications techniques applicables d Industrie Canada The Ringer Equivalence Number is an indication of the maximum number of erminals allowed to be connected to a telepho
21. ected to a compatible modular jack that is also compliant See installation instructions for details Notes e This equipment may not be used on coin service provided by the telephone company e Party lines are subject to state tariffs and therefore you may not be able o use your own telephone equipment if you are on a party line Check with your local telephone company e Notice must be given to the telephone company upon permanent disconnection of your telephone from your line e If your home has specially wired alarm equipment connected to the elephone line ensure the installation of this product does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer US Number is located on the cabinet bottom REN Number is located on the cabinet bottom 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the elephone network the telephone company shall where practicable notify you that temporary discontinuance of service may be required Where prior notice is not practicable and the circumstances warrant such action the elephone company may temporarily discontinue service immediately In case of such temporary discontinuance the telephone company must 1 promptly notify you of such temporary discontinuance 2 afford you the opportunity to correct the situation and 3 inform you of your right to
22. exclusions may not apply to you This warranty gives you specific legal rights and you also may have other rights that vary from state to state If you purchased your product outside the USA or Canada This warranty does not apply Contact your dealer for warranty information Product Registration e Please complete and mail the Product Registration Card packed with your product or visit www rca4phones com to register your new product Product registration is not required for warranty coverage but does allow us to contact you should it be necessary
23. f this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Visit the RCA web site at www rca4phones com Please do not send any products to the Indianapolis address listed in this manual or on the carton This will only add delays in service for your product 7114 Printed in China 12 26 e Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference e Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna e Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected If these measures do not eliminate the interference please consult your dealer or an experienced radio television technician for additional suggestions Also the Federal Communications Commission has prepared a helpful booklet How To Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Please specify stock number 004 000 00345 4 when ordering copies Notice The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operat
24. have their different settings and functions n Base menu items sequence RING TO ANSWER ESSAGE LENGTH REMOTE ACCESS CONTRAST RINGER TONE LOCAL AREA CODE gt TONE PULSE DATE TIME SETTING gt ENG FRA ESP REGISTER ON gt OFF DEREGISTRATIO DEFAULT gt NO RING TO ANSWER 1 While the unit is in STANDBY mode press MENU to enter menu program mode 2 lt or P to select the desired number from 2 to 8 toll saver 3 Press OK to confirm your selection and jump to the next menu item MESSAGE LENGTH 1 While unit is in STANDBY mode press MENU until Message Length appears 2 Press lt or P to select the desired minute from 1 to 4 3 Press OK to confirm your selection and jump to the next menu item REMOTE ACCESS 1 While unit is in STANDBY mode press MENU until remote access appears 2 Use dial keypad 0 9 to input your desired codes lt or gt to move cursor 3 Press OK to confirm the update and jump to the next menu item CONTRAST 1 While unit is in STANDBY mode press MENU until contrast appears 2 Use lt or gt to change LCD contrast level 1 5 3 Press OK to confirm the update and jump to the next menu item RINGER TONE 1 While unit is in STANDBY mode press MENU until ringer tone appears 2 Use lt or P to select your desired ringer melody 1 16 3 Press OK to confirm the update and jump to the next menu item LOCAL AREA CODE 1 While unit is in STANDBY mode press MENU until local
25. ithin your limited warranty period and it is determined that service is required e We will ask that you properly pack your product to avoid shipping damage We recommend that you use the original carton and packing materials e We will ask you to include with your product the following Your name return shipping address and daytime phone number handwritten or typed on a sheet of paper A legible copy of your sales receipt please do not send the original sales receipt e Ship your product prepaid to the address we provide We suggest shipping your product via a traceable carrier as we are not responsible for lost mis directed or damaged shipments You may want to write the date shipped carrier and tracking number here e Upon receipt of your product we will validate your product is under warranty and if determined your product is warranty eligible we will ship to you a new or at our option a refurbished exchange unit of same or similar model This exchange unit will be shipped to you at no cost What your limited warranty does not cover e Customer Instruction Your Owners Manual provides information regarding operating and install instructions Additional information may be obtained by contacting the retailer e Installation and set up service adjustments e Batteries e Damage from misuse neglect unauthorized repair e Products which have been modified or incorporated into other products
26. lete 14 e Microphone 15 e Press to enter a key 16 Select Answerer on off 17 Message skip backward 18 e Make the intercom call e Make the conference call 19 Enter to Answerer function Flash key 20 e TALK SPEAKER button e Make and receive call 21 Battery door nm w gt uo Display icons il Signal strength le New Call m vena a p error fa Installing the Phone Installing the Handset Battery NOTE You must connect the handset battery before use A Nickel metal Hydride battery Ni MH battery Brand name FB Model name NI MH AAA400 mAh 2 4V Capacity 2 4V 400mAh that is compatible with this unit 1 Locate battery and battery door which are packaged together inside a plastic bag and are separate from the handset 2 Locate the battery compartment on the back of the handset 3 Plug the battery pack cord into the jack inside the compartment 4 Insert the battery pack NOTE To ensure proper battery installation the connector is keyed and can be inserted only one way BATTERY 000000 000000 5 Close the battery compartment by pushing the door up until it snaps into place Base Station 1 Choose an area near an electrical outlet and a telephone wall jack RJ11C and place your cordless telephone on a level surface such as a desktop or tabletop or you may mount it on the wall
27. n the base or cordless handset The mute indicator LED on the base will turn ON Or cordless handsets will turn on as MUTE ON shows on the display 2 Press MUTE again to cancel and return to your phone conversation Volume setting Cordless handset When the cordless handset is ON in TALK mode review A or W to adjust the listening level Choose from five volume settings Corded handset or speakerphone When the base in TALK mode review vol vol on the base to adjust the handset volume or speakerphone Four levels for handset and 8 for speakerphone Memory The base and cordless handset each have their own separate memory storage areas 1 In number name editing lt or gt DELETE dial keypad and PAUSE key are used frequently The program mode will exit and return to STANDBY in even of timeout 30s or the EXIT key is depressed Note Cordless handset has only MO M9 2 Storing a name and Number in memory For base i While base unit is in STANDBY mode press STORE and then input any location no A B C 0 9 ii To select location record appears on LCD press STORE again to start inputting number up to 32 digits iii After number edit press STORE again to start name inputting iv After name edit press STORE to save them and exit to STANDBY mode A confirmation tone will be heard For handset othing special but different number and name edit orders Double click at means PAUSE Storing a caller I
28. ne interface The termination on an interface may consist of any combination of devices subject only to he requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five L indice d quivalence de la sonnerie IES sert indiquer le nombre maximal de terminaux qui peuvent tre raccord s a une interface t l phonique La erminaison d une interface peut consister en une combinaison quelconque de dispositifs la seule condition que la somme d indices d quivalence de la sonnerie de tous les dispositifs n exc de pas 5 This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following e Do not use this product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool e Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning e Do not use the telephone to report a gas leak in the vicinity of the leak e Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible
29. one company is known to be a valid number for dialing back used only in very limited areas Once you pick up the phone the number is automatically dialed If you did not program your local area code 1 Use review A W or lt lt gt gt key until the number you want to dial displays he number will display in a 10 digit format i e 555 555 1234 If you programmed your local area code 1 Use review A W or lt lt gt gt key until the number you want to dial displays he numbers displaying seven digits i e 555 1234 are whining your area code However this doesn t guarantee the call is a local call A number with 10 or 11 digits i e 555 5555 1234 is not a local call Press FORMAT 2 If the phone is on hook and PICKUP OR ADJ displays or ADJUST if phone is in off hook adjust the phone number format by pressing FORMAT repeatedly to Scroll through the 7 11 10 digit numbers 3 To dial the displayed number while on hook pick up the handset or press SPEAKER sf or TALK SPEAKER Z NOW DIALING displays and the number is dialed Using your answering machine When a call comes in the unit will ring the number of times you determine during initial setup answer the call and play the greeting and then record a message from the incoming caller You can 1 Answer the call before the unit answers 2 Pick up the phone during the greeting 3 Listen to the incoming message to decide if you want to answer the call 4
30. ory If no entry is made during this 20 seconds period the phone disconnects the call REMOTE ACCESS You can access your answering machine from any touch tone phone by entering your 3 digits security code The unit responds with an operations list Be aware that remote functions do not work with rotary to push button pulse dialing phones Note 123 is the default 3 digits security code REMOTE ACCESS COMMANDS If you want to Erase messages during playback 0 Repeat message during playback 1 Play messages Stop playback during playback 2 Skip to the next message during playback 3 Turn answering machine on off 4 Review menu again 7 ACCESSING YOUR MESSAGES 1 Call your telephone number 2 Enter your 3 digit security code you can enter this code any time during the greeting or after the beep 3 The unit waits for a remote command for 20 seconds after the corrected security code has been entered Do menu selection according to the menu voice prompt Note The unit answers on the 10the ring when it is turned off or the memory is full If memory is full play messages and erase some of them to restore memory After the unit plays the remote menu it waits 20 seconds for a command and then disconnects REMOTE ACCESS ANSWERING MACHINE VIA CORDLESS HANDSET Except for TAM operation on base you can also get it through cordless handset To activate the remote TAM access ensure cordless handset is in STANDBY mode press Answerer
31. product e Active mobile phones in the vicinity may cause interference e Metallic objects may be retained if placed near or on the handset receiver Overview of the base unit Quick dial emergency memory buttons hook switch mute button repeat button AX VOL buttons skip button speaker button PLAY STOP button utton delete button announce button memo button ans on off button store button menu button tone button int conf button flsha exit button redial pause button Charge indicator 5 Overview of the cordless handset Ti ERE To Ze 30 l 3 a Earpiece e End the call e Exit the menu operation e Scroll up on the menu e Increase the earpiece volume Enter the call log e Enter to the menu e Confirm selection e Mute un mute the microphone e Scroll down on the menu Decrease the earpiece volume 6 Enter redial list and dial the recent number 7 Store phone number and memory dialing 8 e Message skip forward 9 e Play amp Stop message 10 Play Announcement 11 Play Memo 12 Press to select ringer level 13 Message De
32. put the line on hold and transfer the call LCD shows HS NUMBER input 1 4 that you expect the destination handset 2 The inquired cordless handset will ring Press TALK SPEAKER 37 to answer the call Note to cancel the transfer press EXIT Transferring call from cordless handset to another cordless handset base During an external call you may transfer the external call to another handset or base 1 Press the INT on original cordless handset to put the line on hold and transfer the call 0 BS 12 3 4 HS shall show 2 Press your wanted number to start transferring to 3 Press the TALK SPEAKER 3 on the ringing cordless handset or pick up the corded handset on the base OR press the speaker on base to answer the call Note to cancel the call transfer you may press EXIT on the originating cordless handset if there is no answer within 60 seconds after transferring the call then both handsets will be rung back call back If neither handset answers within 60 seconds then external call will be automatically dropped Conference the external caller with cordless handset and base Invited by base base cordless handset external If base is already in talking with an external party 1 Press INT on base then input 1 4 for the desired cordless handset 2 The called cordless handset rings press TALK SPEAKER on 3 the called cordless handset 3 Press base INT again and CONFERENCE appears 3 party conference call is set
33. set 3 When the party answers adjust speakerphone volume by vol vol 4 To end the call press the SPEAKER again if in speakerphone mode or put back handset to the cradle again Switching between speakerphone and handset You can switch between speakerphone and handset after dialing a number or at any time during a conversation Switch handset to speakerphone While in handset mode press SPEAKER and then put back handset to cradle Switch speakerphone to handset While in speakerphone mode pickup handset Receiving a call with cordless handset 1 When the phone rings press the TALK SPEAKER 37 on cordless handset 2 Adjust listening volume by reviewing A or V 3 To end the call press the EXIT or put back cordless handset to the charger again Making a call with cordless handset 1 Press the TALK SPEAKER 37 on cordless handset and wait for a dial tone 2 Dial the number using a memory dial number if desired the number shows in the display or Dial the number and then press the TALK SPEAKER 3 3 When the party answers adjust volume by reviewing A or V 4 To end the call press EIXT or put back handset to the charger again Switching between speakerphone and handset You may press TALK SPEAKER 7 to toggle between them Call transfer Transferring call from base to cordless handset During an external call you may transfer the external call from base to handset 1 Press the INT on the base to
34. unication include wireless audio video senders wireless computer networks multi handset cordless telephone systems and some long range cordless telephone systems Important safety instructions e Use only the power supply listed in the user instructions e Use only the batteries listed in the user instructions e Do not allow the charging contacts or the battery to come into contact with metal objects e Do not open the handset base station or charger as you could be exposed o high voltages e Do not allow the charger to come into contact with liquids e Risk of explosion if battery is replaced by an incorrect type e Dispose of used batteries according to the instructions e Always use the cables provided with the product e For pluggable equipment the socket outlet shall be installed near the equipment and shall be easily accessible e This equipment is not designed to make emergency calls when the power ails An alternative has to be made available to allow emergency calls e Do not expose the phone to excessive heat caused by heating equipment or direct sunlight e Do not drop your phone or allow objects to fall on your phone e Do not use any cleaning agents containing alcohol ammonia benzene or abrasives as e these may harm the set e Do not use the product in places where there are explosive hazards e Do not let small metal objects come into contact with the product This can deteriorate audio quality and damage the
35. up Invited by cordless handset 2 cordless handset external If cordless handset is already in talking with an external party 1 Press INT on cordless handset and 1 4 to select the called handset number 2 The called handset rings press TALK SPEAKER 3 on the called cordless handset 3 Press the originating handset INT again and CONFERENCE appears 3 party conference call is setup Invited by cordless handset cordless handset base external If cordless handset in already in talking with an external party 1 Press INT on cordless handset and 0 to invite base 2 Base rings and press SPEAKER sf on base or pick up handset 3 Press the originating cordless handset INT and CONFERENCE appears 3 party conference call is setup Last Number Redial To quickly redial the last number you dialed With cordless handset 1 Press the REDIAL to display redial number then press TALK SPEAKLER 37 to dial out 2 If you get a busy tone and want to keep dialing the number press the REDIAL to quickly redial the number again With corded handset or speakerphone 1 Lift the corded handset or press SPEAKER a 2 Press REDIAL CALL TIMER After you press TALK SPEAKER on the cordless handset or lift the corded handset or press the SPEAKER sf on the base the built in call timer shows in the display and begins counting the length of time of the calll AUTO STANDBY Placing the cordless handset in the charge cradle while the
Download Pdf Manuals
Related Search