Home

Quadra-Fire QVI-30FB-S User's Manual

1. O O This appliance has a Standing Pilot Ignition WARNING HOT SURFACES Before operating this appliance have a qualified Glass and other surfaces are hot during technician operation AND cool down e Remove all shipping materials from inside and or Hot glass will cause burns underneath the firebox DO NOT touch glass until it is cooled NEVER allow children to touch glass Keep children away CAREFULLY SUPERVISE children in same room as Check the wiring fireplace Alert children and adults to hazards of high temperatures Review proper placement of logs rockwool lava rock and vermiculite Check the air shutter adjustment High temperatures may ignite clothing or other Purge gas line with glass assembly removed See dn 1 Section 8 e Keep clothing furniture draperies and other flammable Ensure that there are no gas leaks materials away Ensure that the glass is sealed and in the proper position This appliance has been supplied with an integral barrier Ensure that the flow of combustion and ventilation air is to prevent direct contact with the fixed glass panel DO not obstructed front grilles and vent caps NOT operate the appliance with the barrier removed A WARNING M Fire Risk W Explosion Risk A WARNING Gas may build up while lighting pilot Remove glass assembly before lighting pilot Improper installation adjustment alteration servi
2. 142 mm gt 2 1 2 in 2 1 16 in NS 4in REF 52 mm 102 mm z 13 3 4 in 9 350 3 1 8 80 Two 9 2 13 16 in 71mm 1 1 16 in 28 mm GAS INLET 1 9 16 in ELECTRICAL 6 5 8 ACCESS gt a 3 9 16 in 169 mm IF EQUIPPED 91 mm MODEL DIMENSIONS QVI 30FB S 40 mm Location 9 E p ss see pasas o Figure 15 1 Appliance Dimensions 34 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 B Vent Kits Components Direct Vent Flex Liner Kits see Figure 15 2 LINK DV 30B or LINK DV 30 Masonry 3 inch flex liner kit Expands to 30 feet Includes two liners termination cap flashing and link adapter LINK DV4 30B or LINK DV4 30 Masonry 3 inch flex liner kit Expands to 30 feet and 4 feet respectively Includes two liners termination cap flashing and link adapter LINK DV 30B LINK DV 30 SVRLINK ADP LINK DV4 30B LINK DV4 30 Figure 15 2 Direct Vent Flex Liner Kits Direct Vent Flex Liner Accessory Kits see Figure 15 3 Flash Damp Zero clearance damper flashing kit for use with LINK DV 30B or LINK DV4 30B liner kits LINK ZC ADP Zero clearance chimney adapter SVRLINK ADP Adapter kit colinear to coaxial 3 inches included in above kits FLEX3 30 One 3 inch flexible liner expands to 30 feet FLEX3 30 2
3. Level 2 inspection of the chimney Replace component parts of the chimney and fireplace as specified by the professionals Ensure all joints are properly engaged and the chimney is properly secured When planning an appliance installation it s necessary to determine the following information before installing Minimum fireplace size See Section 3 A Gas supply piping Electrical wiring Finishing details Existing mantel projections See Section 10 Whether optional accessories devices such as a fan wall switch or remote control are desired B Tools and Supplies Needed Before beginning the installation be sure that the following tools and building supplies are available Pliers Hi temp caulking material Hammer Flat blade screwdriver Voltmeter Framing square Gloves Variable speed drill 1 4 Hex drive Safety glasses Manometer Phillips screwdriver Tape measure Non corrosive leak check solution 1 2 3 4 inch length 6 or 8 Self drilling screws Quadra Fire QVI 30FB S 2020 910 Rev 6 09 C Inspect Appliance and Components A WARNING Y Inspect appliance and components for damage Damaged parts may impair safe operation Do NOT install damaged components Do NOT install incomplete components Do NOT install substitute components Report damaged parts to dealer Carefully remove the appliance and components from the packaging The vent system components surr
4. Non HHT venting components hearth components or other accessories used in conjunction with the appliance Any part of a pre existing fireplace system in which an insert or a decorative gas appliance is installed HHT s obligation under this warranty does not extend to the appliance s capability to heat the desired space Informa tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application Consider ation must be given to appliance location and configuration environmental conditions insulation and air tightness of the structure This warranty is void if The appliance has been over fired or operated in atmospheres contaminated by chlorine fluorine or other damaging chemicals Over firing can be identified by but not limited to warped plates or tubes rust colored cast iron bubbling cracking and discoloration of steel or enamel finishes The appliance is subjected to prolonged periods of dampness or condensation There is any damage to the appliance or other components due to water or weather damage which is the result of but not limited to improper chimney or venting installation LIMITATIONS OF LIABILITY The owner s exclusive remedy and HHT s sole obligation under this warranty under any other warranty express or implied or in contract tort or otherwise shall be limited to replacement repair or refund as specified above In no event will HHT be liable for any incidental
5. 5775408 5890485 5931661 5941237 5947112 5996575 6006743 6019099 6048195 6053165 6145502 6170481 6237588 6296474 6374822 6413079 6439226 6484712 6543698 6550687 6601579 6672860 6688302B2 6715724B2 6729551 6736133 6748940 6748942 6769426 6774802 6796302 6840261 6848441 6863064 6866205 6869278 6875012 6880275 6908039 6919884 D320652 D445174 D462436 Canada 1297749 2195264 2225408 2313972 Australia 780250 780403 1418504 or other U S and foreign patents pending Printed in U S A Copyright 2009 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 41
6. U S A or 10 for elevations between 2000 and 4500 feet in Canada If the heating value of the gas has been reduced these rules do not apply To identify the proper orifice size check with the local gas utility If installing this appliance at an elevation above 4500 feet in Canada check with local authorities A WARNING Do NOT use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water D Non Combustible Materials Specification Material which will not ignite and burn Such materials are those consisting entirely of steel iron brick tile concrete slate glass or plasters or any combination thereof Materials that are reported as passing ASTM E 136 Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 C shall be considered non combustible materials E Combustible Materials Specification Materials made of or surfaced with wood compressed paper plant fibers plastics or other material that can ig nite and burn whether flame proofed or not or whether plastered or unplastered shall be considered combustible materials F Electrical Codes NOTICE This appliance must be electrically wired and grounded in accordance with local codes or in the absence of local codes with National Electric Code ANSI NFPA 70 latest edition o
7. d eau Maximum Manifold Pressure Pression 0 0 in w c Col d eau Minimum Manifold Pressure Pression 0 0 in w c Col d eau Total Electrical Requirements 000Vac 00Hz less than 00 Amperes MADE IN USA Model Number INCANADA i ALTITUDE 0 0000 FT 0000 0000FT Modele Serial Number MAX INPUTBTUH 00 000 00 000 MIN INPUTBTUH 00 000 00 000 Serial ORIFICE SIZE HXXXXX 40000X Serie XXXXXXXX 2 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Table of Contents 1 Listing and Code Approvals A Appliance 4 BTU 4 C High Altitude Installations 4 Non Combustible Materials Specification 4 E Combustible Materials Specification 4 F Electrical 4 2 Getting Started A Design and Installation Considerations 5 B Tools and Supplies 5 C Inspect Appliance and Components 5 D Inspect Firebox 0 0 0 c cece ipasa ee ee 6 3 Fireplace Size Requirements A Minimum Fireplace Opening 7 B Clearances assesses esis Rina sean ee 8 4 Termination Locations A Vent Termination Minimum Clearances 9 5 Vent Information and Diagrams A V
8. hold in Im mediately depress red or black piezo button It may require several depressions of the red or black piezo button until PILOT lights If PILOT light does not light after 10 seconds return to step 3 Continue to hold the control knob in for about one minute after the pilot is lit Release knob and it will pop back out Pilot should remain lit If it goes out repeat steps 3 through 6 If knob does not pop up when released stop and im mediately call your service technician or gas supplier If the pilot will not stay lit after several tries turn the gas control knob to OFF and call your service technician or gas supplier Turn gas control knob counterclockwise to E ON To light Burner flip the on off switch to the ON position and close access grille Turn on all electric power to the appliance TO TURN OFF L_l GAS TO APPLIANCE Turn off all electric power to the appliance if service is to be performed Open control access panel Move switch to OFF position Push in gas control knob slightly and turn clock wise Tu to OFF Do not force ntrol access panel Close co 464 9039 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 27 C Check Pilot Flame Appearance Pilot flame must contact the thermocouple and thermopile for reliable appliance operation Pilot flame should be as shown in Figure 12 1 Figure 12 1 Proper Pilot Flame I
9. instructions to prevent direct contact with the fixed glass panel DO NOT operate the appliance with the barrier removed lf you cannot reach your gas supplier call Contact your dealer or Hearth amp Home Technologies if the the fire department barrier is not present or help is needed to properly install one Installation and service must be performed by a qualified installer service agency or the In the Commonwealth of Massachusetts gas supplier installation must be performed by a licensed plumber or gas fitter a CO detector shall be installed in the room where the This appliance may be installed as an OEM installation in appliance is installed manufactured home USA only or mobile home and must be installed in accordance with the manufacturer s instructions and the manufactured home construction and safety standard Title Installation and service of this appliance should be 24 CFR Part 3280 or Standard for Installation in Mobile Homes performed by qualified personnel Hearth amp Home CAN CSA Z240MH Technologies suggests NFI certified or factory trained This appliance is only for use with the type s of gas indicated professionals or technicians supervised by an NFI on the rating plate certified professional Quadra Fire QVI 30FB S 2020 910 Rev 6 09 1 Read this manual before installing or operating this appliance Please retain this owner s manual for future reference Congratulations Congratulations
10. may never be returned to solid fuel in this condition The sidewalls and top structure of the firebox may not be altered with the exception of removable baffles and dampers Cutting of any sheet metal parts of the fireplace in which the gas fireplace insert is to be installed is prohibited except the floor as tested for and as noted above NOTE For actual appliance dimensions refer to Section 15 TOP VIEW FRONT VIEW MINIMUM FIREPLACE SIZE Location QVI30FB S 768 4 mew o e o jme ee ms NOTE If exhaust collar on insert and fireplace damper do not line up add 4 inches 102 mm to minimum fireplace height for bends in vent pipe Figure 3 1 Fireplace Opening Quadra Fire QVI 30FB S 2020 910 Rev 6 09 B Clearances A WARNING y Fire Risk Odor Risk Clearance to combustible material under the insert is 1 4 inch 0 6 cm Use leveling legs to raise insert minimum 1 4 inch above combustible material or outer wrap of factory built firebox EXHAUST VENT PIPE INLET AIR a gt 12 in MAX VENT PIPE MANTEL D 12 in MIN MEASUREMENTS FROM TOP EDGE OF UNIT A WARNING Fire Risk Locate and install appliance to all clearance specifications in manual Figure 3 2 Clearances to Mantels or other Combustibles above Appliance 8 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Term
11. on selecting a Quadra Fire gas appliance an elegant and clean alternative to wood burning appliances The Quadra Fire gas appliance you have selected is designed to provide the utmost in safety reliability and efficiency As the owner of a new appliance you ll want to read and carefully follow all of the instructions contained in this Owner s Manual Pay special attention to all Cautions and Warnings Homeowner Reference Information Model Name This Owner s Manual should be retained for future reference We suggest that you keep it with your other important documents and product manuals The information contained in this Owner s Manual unless noted otherwise applies to all models and gas control systems Your new Quadra Fire gas appliance will give you years of durable use and trouble free enjoyment Welcome to the Quadra Fire family of appliance products We recommend that you record the following pertinent information about your appliance Date purchased installed Serial Number Location on appliance Dealership purchased from Dealer Phone Notes Listing Label Information Location The model information regarding your specific appliance can be found on the rating plate usually located in the control area of the appliance This product may be covered by one or more of the following patents Nos produits sont couverts par un ou plusieurs des brevets suivants United States 4
12. or consequential damages caused by defects in the appliance Some states do not allow exclusions or limitation of incidental or consequential damages so these limitations may not apply to you This warranty gives you specific rights you may also have other rights which vary from state to state EXCEPT TO THE EXTENT PROVIDED BY LAW HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE 4021 645B 04 02 09 Page 2 of 2 40 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 E Contact Information QUADRA FIRE Quadra Fire a brand of Hearth amp Home Technologies Inc 7571 215th Street West www quadrafire com Please contact your Quadra Fire dealer with any questions or concerns For the location of your nearest Quadra Fire dealer please visit www quadrafire com NOTES CAUTION DO NOT DISCARD THIS MANUAL Important operating Read understand and follow Leave this manual with and maintenance these instructions for safe party responsible for use instructions included installation and operation and operation This product may be covered by one or more of the following patents United States 4593510 4686807 4766876 4793322 4811534 5000162 5016609 5076254 5113843 5191877 5218953 5263471 5328356 5341794 5347983 5429495 5452708 5542407 5601073 5613487 5647340 5688568 5762062
13. or other appliances connected to the flue Horizontal venting is NOT allowed Vent this appliance directly outside Use separate vent system for this appliance Minimum Vertical Run Length 14 ft Maximum Vertical Run Length 50 ft C Measuring Standards Vertical measurements listed in the vent diagram Figure 5 1 were made using the following standard Vertical terminations are measured to top of chimney ALL vent specifications MUST be followed This product is tested and listed to these specifications Appliance performance will suffer if specifications are not followed TERMINATION Note To achieve optimum performance of insert minimize or avoid bends in exhaust vent pipe EXHAUST COLLAR INLET AIR COLLAR EXHAUST VENT PIPE V 14 FT MINIMUM 50 FT MAXIMUM 3 INCH COLLAR Factory installed to stainless steel section WARNING DO NOT BLOCK PIPE END WITH INSULATION OR ANY OTHER SEALING MATERIAL STAINLESS STEEL PIPE 3 FT MIN REQUIRED INCLUDED INLET AIR VENT PIPE COLLAR ATTACHMENT BRACKET Figure 5 1 10 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Installation Preparation Prepare the existing solid fuel masonry or factory built non combustible firebox for installation A Flue Damper Fully lock the solid fuel fireplace s flue damper in the open position OR completely remove it B Chimney Ensure chimney is constructed of
14. technician Ensure adequate ventilation Ensure there are no ignition sources such as sparks or open flames A small amount of air will be in the gas supply lines When first lighting appliance it will take a short time for air to purge from lines When purging is complete the appliance will light and operate normally A WARNING CHECK FOR GAS LEAKS Explosion Risk Fire Risk Asphyxiation Risk Check all fittings and connections Do not use open flame Afterthe gas line installation is complete all connections must be tightened and checked for leaks with a commercially available non corrosive leak check solution Be sure to rinse off all leak check solution following testing Fittings and connections may have loosened during shipping and handling A WARNING Fire hazard Do NOT change the valve settings This valve has been preset at the factory Changing valve settings may result in fire hazard or bodily injury HIGH ALTITUDE INSTALLATIONS U L Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U S A and Canada Wheninstalling this appliance at an elevation above 2000 feet it may be necessary to decrease the input rating by changing the existing burner orifice to a smaller size Input rate should be reduced by 495 for each 1000 feet above a 2000 foot elevation in the U S A or 1096 for elevations between 2000 and 4500 feet in Cana
15. terminals of the gas valve The meter should read 325 millivolts minimum while holding the valve knob depressed in the pilot position with the pilot lit and the ON OFF switch in the OFF position Replace the faulty thermopile if the reading is below the specified minimum With the pilot in the ON position disconnect the thermopile leads from the valve Take a reading at the thermopile leads The read ing should be 325 millivolts minimum Replace the thermopile if the reading is below the minimum 30 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Troubleshooting continued Symptom Possible Cause Corrective Action 3 Continued c Defective valve Turn the valve knob to the ON position Place the ON OFF switch in the ON position Check the millivolt meter a the thermopile terminals The millivolt meter should read greater than 125mV If the reading is ac ceptable and if the burner does not come on replace the gas valve d Plugged burner orifice Check the burner orifice for stoppage Remove stop page e Wall switch or wires are defective Follow the corrective action in Symptom and Pos sible Cause 1 a above Check the switch and wiring Replace where defective 4 Frequent pilot outage a Pilot flame may be too high or too low or blow Clean thermocouple and adjust the pilot flame for problem ing out high pressure causing pilot safety to drop maximum flame impingement Follow lighting instruc out tion
16. use the leveling legs included with the insert to set each corner of the base Position any excess flexible vent pipe back up into chimney without sagging Twist and push flex vent together to shorten Install fiberglass insulation pieces to back face of surround Attach surround Follow instructions accompanying surround Push insert so that surround becomes tight against face of fireplace Quadra Fire QVI 30FB S 2020 910 Rev 6 09 13 D Installing Adaptor and Termination Cap For installation of termination cap see minimum vent heights for various pitched roofs see Figure 7 3 To install adaptor see Figure 7 4 HORIZONTAL OVERHANG 20 INCHES MIN VERTICAL WALL LOWEST DISCHARGE OPENING GAS DIRECT VENT TERMINATION CAP L ROOF PITCH IS X 12 H MIN MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING Roof Pitch H Min Ft Flatto 6 12 1 0 Over 6 12 to 7 12 1 25 Over 7 12 to 8 12 1 5 Over 8 12 to 9 12 2 0 Over 9 12 to 10 12 2 5 Over 10 12 to 11 12 3 25 Roof Pitch H Min Ft Over 11 12 to 12 12 4 0 Over 12 12 to 14 12 5 0 Over 14 12 to 16 12 6 0 Over 16 12 to 18 12 7 0 Over 18 12 to 20 12 7 5 Over 20 12 to 21 12 8 0 8 foot minimum in snow regions Figure 7 3 Minimum Height from Roof to Lowest Discharge Opening Masonry EXHAUST AIR VENT PIPE Figure 7 5 14 LINK DV30
17. 593510 4686807 4766876 4793322 4811534 5000162 5016609 5076254 5113843 5191877 5218953 5263471 5328356 5341794 5347983 5429495 5452708 5542407 5601073 5613487 5647340 5688568 5762062 5775408 5890485 5931661 5941237 5947112 5996575 6006743 6019099 6048195 6053165 6145502 6170481 6237588 6296474 6374822 6413079 6439226 6484712 6543698 6550687 6601579 6672860 668830282 6715724B2 6729551 6736133 6748940 6748942 D320652 D445174 D462436 Canada 1297749 2195264 2225408 or other U S and foreign patents pending ou autres brevets americains et etrangers en attente GAS FIRED Quadra Fire a brand of Hearth amp Home Technologies Inc Type of Gas Not for use with solid fuel QUADRA IRE 7571 215th Street West Lakeville MN 55044 C US Ne doit pas entre utilise avec un combustible solide LISTED Type of Gas Sorte De Gaz This appliance must be installed in accordance with local codes if any if not follow ANSI 2223 1 inthe USA or CAN CGA B149 installation codes Installer l appareil selon les codes ou reglements N ATU RAL GAS locaux ou en l absence de tels reglements selon les codes d installation CAN CGA B149 ANSI 221 CSA 2 XX MXX UL307B Gas and Electric Information Minimum Permissible Gas Supply for Purposes of Input Adjustment Approved Minimum De Gaz Acceptable 0 0 in w c Col d eau Maximum Pressure Pression 0 0 in w c Col
18. 5B 04 02 09 Page 1 of 2 Quadra Fire QVI 30FB S 2020 910 Rev H 6 09 39 D Limited Lifetime Warranty continued WARRANTY CONDITIONS This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor A list of HHT authorized dealers is available on the HHT branded websites This warranty is only valid while the HHT appliance remains at the site of original installation Contact your installing dealer for warranty service If the installing dealer is unable to provide necessary parts contact the nearest HHT authorized dealer or supplier Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom you originally purchased the product Check with your dealer in advance for any costs to you when arranging a warranty call Travel and shipping charges for parts are not covered by this warranty WARRANTY EXCLUSIONS This warranty does not cover the following Changes in surface finishes as a result of normal use As a heating appliance some changes in color of interior and exterior surface finishes may occur This is not a flaw and is not covered under warranty Damage to printed plated or enameled surfaces caused by fingerprints accidents misuse scratches melted items or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes Repair or replacement of parts that are subject to n
19. B Installation LINK DV4 30B Installation TERMINATION CAP EXHAUST AIR VENT PIPE OR INLET AIR VENT PIPE Sharp Edges Wear protective gloves and safety oor glasses during installation Damper Flashing Kit Optional For use with LINK DV4 30B Liner Kit Note Damper may have to be removed to use this kit Run flex liners through 3 holes in damper flashing Attach damper flashing to firebox roof with self tapping screws included in kit CLASS A PIPE 7 4 To help eliminate cold air drafts it may be necessary to place non combustible insulation around the flues as they go though the damper Note The LINK DV4 30B system REQUIRES this insulation Factory Built Wood Burning OPTIONAL LINK ZC ADPB FOR USE WITH CLASS A WOODBURNING PIPE EA 4 WARNING DO NOT BLOCK THIS PIPE END Note Untwist the pipe while extending it to achieve full 30 length INLET AIR Remove 18 inch x 18 inch flashing on cap by removing VENT PIPE 3 screws Connect both the LINK ZC ADPB to Class A Pipe and the termination cap to the LINK ZC ADPB with the self tapping screws provided Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Gas Information A Fuel Conversions Before making gas connections ensure that appliance be ing installed is compatible with the available gas type Any natural or propane gas conversions necessary to meet the app
20. Do not cover any burner port holes Use this material to give the appliance a realistic ash bed Save the remaining ember materials for use during appliance servicing The embers provided should be enough for 3 to 5 applications Quadra Fire QVI 30FB S 2020 910 Rev 6 09 21 E Positioning the Logs Log Assembly LOGS QVI30FB LOG PLACEMENT INSTRUCTIONS Log Placement CAUTION Logs are fragile Carefully remove the logs from the packaging LOG 1 SRV2020 140 Place log 1 by locating the legs of log over the air deflector The notch or the back side of the log should center and sit against air deflector 2020 144E 10 07 22 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 LOG 2 SRV2020 141 Position log 2 by locating its slot over the tab on the front left of the burner The slot in the left end of the log slides over the grate Slide right corner of log all the way forward on the tab LOG 3 2020 142 Position log 3 by locating its slot over the tab on the front right of the burner The slot in the right end of the log slides over grate Slide log all the way back on tab and grate LOG 4 SRV340 704 Place log 4 across log 1 and log 2 in the grooved out areas as shown Quadra Fire QVI 30FB S 2020 910 Rev 6 09 LOG 5 SRV340 706 Place log 5 across log 1 and log 3 The notch in the bottom of the log sets on the carved out edge on top of log 3 The back of the log sits in the gro
21. E ATTACH TO ANY METAL SURFACE Quadra Fire QVI 30FB S 2020 910 Rev 6 09 19 1 Finishing A Mantel Projections Figure 10 1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance not the surround EXHAUST VENT PIPE INLET AIR gt 12 in MAX lt VENT PIPE MANTEL 12 in MIN MEASUREMENTS FROM TOP EDGE OF UNIT D Figure 10 1 Clearances to Mantels or other Combustibles above Appliance B Installing Trim Surrounds Combustible materials MUST NEVER overlap onto the front face 1 Find the coiled low voltage wires and ON OFF switch at tached to outer right side of the insert see Figure 10 2 2 Reconnect the low voltage wires to the ON OFF switch 3 Attach surround assembly by hooking the support bracket on the locating tabs on top of the gas insert fireplace see Figure 10 2 Once the surround assem bly is on the locating tabs ensure the bottom hooks are resting on the locating pins at the base Reposition the fireplace if necessary Refer to surround instruc tions provided with the decorative surround LOCATING TABS Figure 10 2 Trim Surround Installation 20 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 FIREBOX 1 Appliance Setup A Remove Shipping Materials Remove shipping materials from inside or underneat
22. NOT CONNECT 110 VAC TO THE CONTROL VALVE Improper installation adjustment al teration service or maintenance can cause injury or property damage Re fer to the owner s information manual provided with this appliance This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air If not installed operated and main tained in accordance with the man ufacturer s instructions this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause can cer birth defects or other reproduc tive harm Keep burner and control compartment clean See installation and operating instructions accompanying appliance f you cannot reach your gas sup plier call the fire department C Use only your hand to push in or turn the gas control knob Never use tools If the knob will not push in or turn by hand don t try to repair it call a qualified service technician Force or attempted repair may result in a fire or explo sion Do not use this appliance if any part has been under water Im mediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water CAUTION Hot while in operation Do not touch Keep children clothing furniture gaso line and other liquids having flammable vapors a
23. Owner s Manual Installation and Operation OUADRA FIRE Model s QVI 30FB S GAS FIRED C US LISTED CAUTION DO NOT DISCARD THIS MANUAL Important operating Read understand and follow Leave this manual with and maintenance these instructions for safe party responsible for use instructions included installation and operation and operation A WARNING If the information in these WARNING instructions is not followed exactly a fire HOT SURFACES or explosion may result causing property piste are hot during damage personal injury or death Se Cu eet Hot glass will cause burns Do not store or use gasoline or other flam DO NOT touch glass until it is cooled bl d liquids in th icinit f NEVER allow children to touch glass vapors and liquids in the vicinity Keep children away this or any other appliance CAREFULLY SUPERVISE children in same room as What to do if you smell gas replace T ht g Alert children and adults to hazards of high temperatures High temperatures may ignite clothing other flammable Do not touch any electrical switch Do not materials use any phone in your building Keep clothing furniture draperies and other flammable materials away Immediately call your gas supplier from a LU neighbor s phone Follow the gas suppli This appliance has been supplied with an integral barrier er s
24. SSONOS ii dee dc sitchin gine M ERE EE Ember Positioning the Logs Glass Assembly Air Shutter Setting o0mmocomms rm 12 Operating Instructions Before Lighting Lighting Appliance Check Pilot Flame Appearance After Appliance is Frequently Asked Questions moogm r 13 Troubleshooting A Standing Pilot Ignition 14 Maintaining and Servicing Appliance A Maintenance 15 Reference Materials Appliance Dimension Vent Kits Service Parts eid reb SLE eee eds Limited Lifetime Contact Information moomgm r Contains updated information Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Listing and Code Approvals A Appliance Certification MODELS QVI 30FB S LABORATORY Underwriters Laboratories Inc UL TYPE Vented Gas Appliance Heaters STANDARD ANSI Z21 88 2002 CSA2 33 2002 UL307B This product is listed to ANSI standards for Vented Gas Applianc
25. Two 3 inch flexible liners expands to 30 feet each FLEX3 CNCT FLEX CNCT Connector kit 3 inch liner to 3 inch liner Figure 15 3 Direct Vent Flex Liner Accessory Kits one connector per kit Quadra Fire QVI 30FB S 2020 910 Rev 6 09 35 QUADRA IDE Service Parts QVI 30FB S Service Parts Diagram Beginning Manufacturing Date Oct 2007 Ending Manufacturing Date Part number list on following page 36 Quadra Fire QVI 30FB S 2020 910 Rev H 6 09 Service Parts List QVI 30FB S a IMPORTANT THIS IS DATED INFORMATION When requesting service or replacement parts for your appliance please provide model number and serial number All parts listed Stocked in this manual may be ordered from an authorized dealer at Depot EM DESCRIPTION comments PARTNUMBER LogSet Assembly LOGSQVSOB Y 1 tot 5 5 0 SRV2020440 2 Log2 8 2020141 8 tos SRV2020142 4 Logd S SRVMOTOM 5 Logo SRVMOT0 6 Log 5 7 t SRV ATO 8 SlidePlateAssembly 783108A SlidePlateHande 2019200 _ 9 BafleAssemby ooo 10 Piezolgnitor 2053 Y n O ovos Y 12 Grate Assembly 2020005 13 GasDowAsemy onewe Y 14 VaveCoverPlate 7835 BowrAse
26. and or adjust the pilot for maximum flame impingement lighting instructions Ensure that the thermocouple connection at the gas valve is fully inserted and tight hand tighten plus 1 4 turn Disconnect the thermocouple from the valve place one millivolt meter lead wire on the tip of the thermcouple and the other meter lead wire on the thermocouple copper lead Start the pilot and hold the valve knob in If the millivolt reading is less than 15mV replace the thermocouple b Defective valve If the thermocouple is producing more than 15 millivolts replace faulty valve 3 The pilot is burning a ON OFF switch or wires Check the ON OFF switch and wires for proper connections Place there is no burner flame defective the jumper wires across the terminals at the switch If the burner the valve knob is in the ON comes on replace the defective switch If the switch is OK place the position and the ON OFF jumper wires across the switch wires at the gas valve If the burner switch is in the ON position comes on the wires are faulty or connections are bad b Thermopile may not be gener If the pilot flame is not close enough physically to the thermopile ating sufficient millivoltage adjust the pilot flame Be sure the wire connections from the thermopile at the gas valve terminals are tight and that the thermopile is fully inserted into the pilot bracket Check the thermopile with a millivolt meter Take the reading at TH TP amp TP
27. ce or Replace glass assembly after lighting pilot maintenance can cause injury or property damage Refer to the owner s information manual provided with this appliance For assistance or additional information consult a qualified installer service agency or the gas supplier A WARNING Contact your dealer or Hearth amp Home Technologies if the barrier is not present or help is needed to properly install one Do NOT use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water 26 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 B Lighting Appliance Standing Pilot Ignition WARNING If you do not follow these instructions exactly a fire or explosion may result causing property damage personal injury or loss of life A This appliance has a pilot which must be lighted by hand When lighting the pilot follow these instructions exactly BEFORE LIGHTING smell all around the appliance area for gas Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS Do nottry to light any appliance Do not touch any electric switch do not use any phone in your building Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions WARNING DO
28. ceptable such cracks may be repaired with the SRV PACK service kit See Service Parts List Cracks that are unacceptable Cracks greater than 1 32 in wide and 3 in long are at risk of growing Cracks that penetrate entirely through the firebrick material Inspection for cracking should be run when the appliance is cool Cracks tend to close as the appliance heats up 6 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Fireplace Size Requirements A Minimum Fireplace Opening Minimum fireplace opening requirements are shown in Figure 5 1 WARNING Risk of Fire or Burns Provide adequate clearance around air openings and for service access Due to high temperatures the appliance should be locat ed out of traffic and away from furniture and draperies The firebrick refractory glass doors screen rails screen mesh and log grates can be removed from a factory built firebox in order to gain minimum gas insert opening requirements Any smoke shelves shields and baffles may be removed from the factory built firebox if attached with mechanical fasteners The metal floor of the solid fuel firebox may be removed to facilitate the installation of the insert The appliance may not be placed directly on the base of the outer wrap a 1 4 inch airspace must be provided between the insert and the floor of the outer wrap Use the levelling legs to raise the insert a minimum of 1 4 inch The original fireplace
29. cy of appliance servicing and maintenance will depend on use and the type of installation a qualified service technician should perform an appliance checkup at the beginning of each heating season A WARNING Risk of injury or property damage Before servicing Turn off gas Turn off electricity to appliance Disable remote control if one is present Ensure appliance is completely cooled After servicing CAUTION Handle glass assembly with care NOTE Clean glass after initial 3 4 hours operation Longer operation without cleaning glass may cause a permanent white film on glass When cleaning glass door Avoid striking scratching or slamming glass Do NOT use abrasive cleaners Use a hard water deposit glass cleaner on white film Replace any screen or barrier that was removed Do NOT clean glass when hot Reseal and reinstall any venting removed for servicing Turn off appliance after 3 4 hours of operation and ALLOW TO COOL Remove and clean glass assembly Replace glass assembly and operate appliance for additional 12 hours Refer to maintenance instructions A WARNING Condition of firebox Burner ignition and operation Inspect external vent cap regularly Burner air shutter adjustment aZ Ensure no debris blocks cap Gas connections and fittings Combustible materials blocking cap may ignite Obstructions of termination Restricted air flow affects burner operation
30. d run the appliance for an additional 12 hours This will help to cure the products used in the paint and logs During this break in period it is recommended that some windows in the house be opened for air circulation This will help avoid setting off smoke detectors and help eliminate any odors associated with the appliance s initial burning 28 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 A WARNING CAUTION Fire Risk Smoke and odors released during initial operation Open windows for air circulation High Temperatures Leave room during initial operation Keep combustible household items away from Smoke may set off smoke detectors appliance Smoke and odors may be irritating to sensitive Do NOT obstruct combustion and ventilation air individuals Do NOT place combustible items on top of or in front of appliance Keep furniture draperies away from appliance A WARNING Fire Hazard Keep combustible materials gasoline and CAUTION other flammable vapors and liquids clear of appliance Prevent accidental appliance operation when not lt Do NOT store flammable materials in the attended appliance s vicinity Unplug or remove batteries from remote control if absent Do NOT use gasoline lantern fuel kerosene or if appliance will not be used for an extended period of charcoal lighter fluid or similar liquids in this time appliance Property damage possible from elevated temperat
31. da If the heating value of the gas has been reduced these rules do not apply To identify the proper orifice size check with the local gas utility If installing this appliance at an elevation above 4500 feet in Canada check with local authorities Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Electrical Information A Wiring the Appliance Appliance Requirements This appliance DOES NOT require 110 120 VAC to Note Electrical wiring must be installed by a licensed operate electrician It is recommended that a 110 VAC junction box be connected for use with fan or remote control See Figure Note This appliance must be electrically wired and grounded 9 2 for junction box wiring in accordance with local codes or in the absence of local codes with National Electric Code ANSI NFPA 70 latest edition or the Canadian Electric Code CSA C221 1 A WARNING A 110 120 VAC circuit for this product must be protected Wire 110 IG else thea BOX with ground fault circuit interrupter protection in compliance Do NOT wire 110V to valve with the applicable electrical codes when it is installed in Do NOT wire 110V to wall switch locations such as in bathrooms or near sinks Incorrect wiring will damage millivolt valves Incorrect wiring will override IPI safety lockout and may cause explosion CAUTION ON OFF Switch Prevent accidental appliance operation when not attended An ON OFF sw
32. e Heaters and applicable sections of Gas Burn ing Heating Appliances for Manufactured Homes and Recreational Vehicles and Gas Fired Appliances for Use at High Altitudes NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE This appliance is tested and approved as either supplemen tal room heat or as a decorative appliance It should not be factored as primary heat in residential heating calculations Note To assure top performance safety and efficiency inserts must be installed with an approved flue liner as per CAN CGA B 149 or National Fuel Gas Code ANSI Z223 these instructions Note This installation must conform with local codes In the absence of local codes you must comply with the National Fuel Gas Code ANSI Z223 1 latest edition in the U S A and the CAN CGA B149 Installation Codes in Canada B BTU Specifications Maximum Minimum ui Models input input Orifice U S 0 2000 ft or Canada 2000 4500 ft BTU h BTU h Size DMS QVI 30FB S NG QVI 30FB S LP C High Altitude Installations U L Listed gas appliances are tested and approved with out requiring changes for elevations from 0 to 2000 feet in the U S A and Canada When installing this appliance at an elevation above 2000 feet it may be necessary to decrease the input rat ing by changing the existing burner orifice to a smaller size Input rate should be reduced by 4 for each 1000 feet above a 2000 foot elevation in the
33. e years of trouble free service If you do experience a problem this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken This troubleshooting guide can only be used by a qualified service technician A Standing Pilot Ignition System 1 After repeated triggering a Defective ignitor Check the spark at the electrode and pilot If no spark and electrode of the red or black piezo wire is properly connected replace the ignitor ignitor button the spark e 1 1 f ignitor will not light the pilot b Defective pilot or misaligned Using match light the pilot If the pilot lights turn off the pilot and electrode spark at electrode trigger the red piezo ignitor button again If the pilot lights an im proper gas air mixture caused the bad lighting and a longer purge period is recommended If the pilot will not light ensure the gap at the electrode and pilot is one eighth 1 8 inch to have a strong spark If the gap is OK replace the pilot c No gas or low gas pressure Check the remote shut off valves from the fireplace Usually there is a valve near the gas main There can be more than one 1 valve between the fireplace and the main d No LP in tank Check the LP propane tank You may be out of fuel 2 The pilot will not stay lit a Defective thermocouple Check that the pilot flame impinges on the thermocouple Clean after carefully following the
34. ent Table 10 B Horizontal Venting 10 C Measuring 10 6 Installation Preparation A Flue 11 Chimney wen Ad a 11 C Gas Bine ovato en Oe EN 11 D Hearth or Hearth Extension 11 E Fireplace Conversion Notice 11 F Remote Control saadet ena wads 11 7 Installing Vent Pipe and Appliance A Venting Components 12 B Connecting Vent 12 C Placing Securing and Leveling the Appliance 13 D Installing Adaptor and Termination Cap 14 8 Gas Information A Fuel 5 B Gas Pressures C Gas Connection eet ab eke ed wears 9 Electrical Information A Wiring the B Junction Box C Installation for Fan 10 Finishing A Mantel lt 5 B Installing Trim 5 5 11 Appliance Setup Remove Shipping Materials Clean the sACCO
35. f adjustment is needed remove cap screw from gas valve using 1 8 inch standard screwdriver see Figure 12 2 Turn adjustment screw clockwise to increase pilot flame size Make small adjustments ADJUSTMENT SCREW Figure 12 2 Adjustments Do NOT turn adjustment screw counter clockwise too far as it will come out of the valve allowing gas to escape Replace cap screw and seal to prevent gas leaks Check for gas leaks after tightening D After Appliance is Lit A WARNING Glass door must be in place when appliance is operating Risk of Combustion Fumes Fire Do NOT operate appliance with glass door removed Open viewing glass for servicing only Glass door MUST be in place and sealed before operating appliance Only use glass door certified for use with appliance Glass replacement should be done by qualified technician Initial Break in Procedure When you light the appliance you may notice that it pro duces heat which does have an associated odor or smell If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process Condensation of the glass is normal Note The appliance should be run three to four hours on the initial start up Turn it off and let it cool completely Remove and clean the glass Replace the glass an
36. h the firebox B Clean the Appliance Clean vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity C Accessories Install approved accessories per instructions included with accessories See Service Parts List for appropriate accessories A WARNING Shock or fire risk Use ONLY optional accessories approved for this appliance Using non listed accessories voids warranty Using non listed accessories may result in a safety hazard Only Hearth amp Home Technologies approved accessories may be used safely D Ember Placement A WARNING Explosion Risk Follow ember placement instructions in manual Do NOT place embers directly over burner ports Replace ember material annually Improperly placed embers interferes with proper burner operation Placing the Ember Material Ember material is shipped with this gas appliance To place the ember material Embers CANNOT be placed directly over ports When placing Glowing Embers onto the burner care should be taken so that the ports are not covered Place the dime size ember pieces near port holes in burner top sides and front see Figure 11 1 Failure to follow this procedure will likely cause lighting and sooting problems BURNER PAN AIR SHUTTER EMBER MATERIAL TOP SURFACE AND FRONT Figure 11 1 Placement of Embers Place Mystic Ember over burner surface and around base of burner
37. ination Locations A Vent Termination Minimum Clearances A WARNING Figure 4 1 specifies minimum vent heights for various pitched roofs Fire Risk Asphyxiation Risk Terminations MUST meet minimum clearances Exhaust gases are hot Nearby vents may draw fumes into house HORIZONTAL OVERHANG 20 INCHES MIN VERTICAL WALL LOWEST DISCHARGE OPENING GAS DIRECT VENT TERMINATION CAP L ROOF PITCH IS X 12 H MIN MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING Roof Pitch H Min Ft Flatto 6 12 reiten eerte 1 0 Over 6 12 10 7 12 cnet etes 1 25 Over 7 12 10 8 12 unen ens 1 5 Over TAO Deseo ed 2 0 Over 9 12 to 10 12 nnne 2 5 Over 10 12 to 11 12 3 25 Over 11 12 to 12 12 iacet 4 0 Over 12 12 to 14 12 Over 14 12 to 16 12 Over 16 12 to 18 12 Over 18 12 to 20 12 Over 20 12 to TAs 8 0 8 foot minimum in snow regions Figure 4 1 Minimum height from roof to lowest discharge opening Quadra Fire QVI 30FB S 2020 910 Rev 6 09 9 5 Vent Information and Diagrams A Vent Table Key ander A WARNING The abbreviations listed in this vent table key are used in the vent diagrams Fire Hazard Explosion Risk Asphyxiation Risk Do NOT connect this gas appliance to a chimney flue serving a separate solid fuel or gas burning appliance May impair safe operation of this appliance B Horizontal Venting
38. ion stainless steel flexible pipe included of inlet air vent to the inlet collar on the collar slide plate with insert see Figure 7 1 NOTE The collar slide plate may be Onelength of 3 inch flexible vent pipe for combustion air peme venom appliance te ald included with vent kit Flexible vent pipe for exhaust air included with vent kit Seal opening between flex vent and chimney just above insert Unfaced fiberglass insulation may be used for this purpose One pipe to cap adaptor included with vent kit One vertical termination cap included with vent kit Note To achieve optimum performance of insert minimize or avoid bends in exhaust vent pipe TERMINATION CAP EXHAUST COLLAR INLET AIR COLLAR EXHAUST VENT PIPE Vz 14 FT MINIMUM 50 FT MAXIMUM 3 INCH COLLAR Factory installed to stainless steel section WARNING DO NOT BLOCK PIPE END WITH INSULATION OR ANY OTHER SEALING MATERIAL STAINLESS STEEL PIPE 3 FT MIN REQUIRED INCLUDED INLET AIR VENT PIPE COLLAR ATTACHMENT BRACKET Figure 7 1 12 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY A WARNING Fire Risk Only an approved Hearth amp Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces No other components such as shrouds sheet metal plates etc may be used
39. ired by the locality In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fitter NOTE A listed and Commonwealth of Massachusetts ap proved 1 2 inch 13 mm T handle manual shut off valve and flexible gas connector are connected to the 1 2 inch 13 mm control valve inlet If substituting for these components please consult local codes for compliance Refer to Section 15 for location of gas line access in ap pliance NOTE Gas line may be run from either side of the appliance provided the hole in the outer wrap does NOT exceed 2 1 2 inches in diameter and does not penetrate the firebox A WARNING Gas Leak Risk Support control when attaching pipe to prevent bending gas line NOTE The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non combustible unfaced insulation to prevent cold air infiltration Ensure that gas line does not come in contact with outer wrap of appliance Follow local codes Incoming gas line should be piped into the valve compartment and connected to the 1 2 inch connection on the manual shutoff valve Check all fittings and connections of appliance which may have loosened during shipping Quadra Fire QVI 30FB S 2020 910 Rev 6 09 15 16 A WARNING Fire or Explosion Hazard Gas buildup during line purge may ignite Purge should be performed by qualified
40. itch is included with the decorative Unplug or remove batteries from remote control if absent or surround decorative front and should attached to if appliance will not be used for an extended period of time surround facing See Installation instructions for remote Property damage possible from elevated temperatures control f desired an additional wall switch or thermostat may be added to system as shown in Figure 9 1 STANDING PILOT 2 REMOTE SWITCH F PIGTAIL a ON OFF SWITCH WHT o o RED OPTIONAL WALL SWITCH THERMOSTAT OR REMOTE Figure 9 1 Standing Pilot Ignition Wiring Diagram Quadra Fire QVI 30FB S 2020 910 Rev 6 09 17 B Junction Box Installation INSERT STRAIN RELIEF AROUND CORD IN THIS END FROM OUTSIDE OF UNIT FEED PLUG THROUGH HOLE SIDEWALL Figure 9 2 Junction box installation Optional Accessories Connecting the electrical junction box is required if using a blower or remote Plug the cord into a convenient outlet An electrician may install an outlet box inside the fireplace Place the outlet in the lower back corner of the fireplace Must use cord supplied CAUTION Label all wires prior to disconnec
41. lean Glass Air passageways grilles control compartment Burner burner ports Risk of Fire Delayed ignition or explosion Exposure to combustion fumes Odors A WARNING Annual inspection by qualified technician recommended Check Condition of doors surrounds and fronts Condition of glass glass assembly and glass seal Obstructions of combustion and ventilation air Condition of logs 32 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 Inspect Maintenance Tasks Doors Surrounds 1 Assess condition of screen and replace as necessary Recommend addition of screen if one is not present and Fronts 2 Inspect for scratches dents or other damage and repair as necessary 3 Verify no obstructions to airflow through the louvers 1 i ition Gasket Seal Glass Inspect gasket seal and its condition Pine and Glass 2 Inspect glass panels for scratches and nicks that can lead to breakage when exposed to heat 3 Confirm there is no damage to glass or glass frame Replace as necessary 4 Verify that latches engage properly clip studs are not stripped and glass attachment components are intact and operating properly Replace as necessary 5 Clean glass Replace glass assembly if severely coated with silicate deposits that cannot be removed Valve Compartment 1 Vacuum and wipe out dust cobwebs debris or pet hair Use caution when cleaning these areas Screw and Firebox Top tips that have penet
42. liance and locality needs must be made by a qualified technician using Hearth amp Home Technologies specified and approved parts B Gas Pressures Proper input pressures are required for optimum appli ance performance Gas line sizing requirements need to be made following NFPA54 A WARNING Fire Risk Explosion Hazard High pressure will damage valve Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1 2 psig Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1 2 psig A WARNING Verify inlet pressures High pressure may cause overfire condition Low pressure may cause explosion Verify minimum pressures when other household gas appliances are operating Install regulator upstream of valve if line pressure is greater than 1 2 psig Pressure requirements for appliance are shown in the table below Minimum pressures must be met when other household gas appliances are operating Natural Gas Propane T 5 0 inches 11 0 inches Minimum inlet pressure W W C C 14 0 inches 14 0 inches Maximum inlet gas pressure W C W C 5 inch 10 0 inch Manifold pressure Dantes W C W C C Gas Connection Note Have the gas supply line installed in accordance with local building codes if any If not follow ANSI 223 1 Installation should be done by a qualified installer approved and or licensed as requ
43. my OovrPate 785 Glass Latch Assemby Qly2Req 3861224 Y Junction Box 042800 Y ez o Sw jPictTue SRV485301 Y RheosatAssemby osoa RheottKnb 0052 Y TempSensor _ 107584 Y Thermocouple 25 Y lt Tnemopie moss Y _ Vent Pipe Assembly 768 380 Vermiculite Embers MYSTIC EMBERS Wiring Assembly 2020 069 Y Wiring Assembly NE GNE pO Conversion Kit NG NGKS QVI30FB _ _ Conversion Kit LP LPKS QVIGOFB Regulator LP 230 1520 Additional service part numbers appear on following page Quadra Fire QVI 30FB S 2020 910 Rev 6 09 37 QUADRA FIDE C Service Parts QVI 30FB S Service Parts Diagram Beginning Manufacturing Date Oct 2007 Ending Manufacturing Date Valve Assembly IMPORTANT THIS IS DATED INFORMATION When requesting service or replacement parts for your appliance please provide model number and serial number All parts listed in this manual may j Stocked be ordered from an authorized dealer at Depot Pilot Assembly NG fasmo Y 2 PiotGaset 7684323 S Burner Orifice NG 31A 5680 Y E Burner Orifice LP 450A 44681 Y 778 69 J 6 Pilot Bracket Gasket Flex Ball VaveAssemby 302 320 Valve NG Flame Control Knob 571 533 Pilot Con
44. ng the gas insert Have the chimney and adjacent structure inspected and cleaned by qualified professionals Hearth amp Home Technologies recommends that NFI or CSIA certified professionals or technicians under the direction of certi fied professionals conduct a minimum of a NFPA 211 Level 2 inspection of the chimney Replace component parts of the chimney and fireplace as specified by the professionals Ensure all joints are properly engaged and the chimney is properly secured F Remote Control The receiver for the remotes must be installed BETWEEN the base pan of the insert and the firebox of the wood burning fireplace see photo below EXISTING SIDE REFRACTORY REMOTE RECEIVER UNIT EXISTING BOTTOM OF FIREPLACE 4 we Quadra Fire QVI 30FB S 2020 910 Rev H 6 09 11 7 Installing Vent Pipe and Appliance A Venting Components B Connecting Vent Pipe Reference instructions in the termination kit Install the 3 inch flexible vent pipe s down through the chimney Sharp Edges Wear protective gloves and safety oor glasses during installation The vertical vent termination system installed on this model Secure the exhaust flexible vent pipe to the 3 foot section stainless steel flexible vent pipe using the factory installed 3 inch collar in the stainless steel section of pipe see Figure 7 1 includes Use 3 screws to attach either a 4 foot or 30 foot section One 3 foot sect
45. non combustible materials Ensure chimney is clean and in good working order Ensure that all chimney cleanouts fit properly to prevent air leakage into chimney C Gas Line Note If the factory built fireplace has no gas access hole provided an access hole of 1 inch 25 mm diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship like manner This access hole must be plugged with non combustible insulation after the gas supply line has been installed Install gas line into firebox cavity Check local codes and gas line sizing requirements following NFPA54 See Section 8 D Hearth or Hearth Extension A WARNING Fire Risk A hearth or hearth extension if present must comply with either of the following The solid fuel burning fireplace manufacturer s specification Local building codes required by authority having jurisdiction NFPA 211 E Fireplace Conversion Notice Permanently attach the label with the following warning to the inside lower back of the fireplace firebox into which the insert is being installed Silicone may be required to properly secure the label A WARNING Fire Risk This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced and the fireplace re approved by the authority having jurisdiction Prior to installi
46. nstruction warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent authorized HHT dealer distributor whichever occurs earlier The warranty shall commence no later than 24 months following the date of product shipment from HHT regardless of the installation or occupancy date The warranty period for parts and labor for covered components is produced in the following table The term Limited Lifetime in the table below is defined as 20 years from the beginning date of warranty coverage for gas appliances and 10 years from the beginning date of warranty coverage for wood pellet and coal appliances These time periods reflect the minimum expected useful lives of the designated components under normal operating conditions Warranty Period Period HHT Manufactured Appliances and Venting Le Components Covered Parts Labor Wood Pellet Coal Electric Venting All parts and material except as 1 Year X X X X X X X covered by Conditions Exclusions and Limitations listed EE E glass Factory installed blowers 808 syes x Fieposandbumpos 5years tyear x X 1 Castings and baffles Manifold tubes 10 1 year X Burners logs and refractory ears Limited i Lifetime Tx x xT x x mmm beyond warranty period See conditions exclusions and limitations on next page 4021 64
47. ormal wear and tear during the warranty period These parts include paint wood pellet and coal gaskets firebricks grates flame guides and the discoloration of glass Minor expansion contraction or movement of certain parts causing noise These conditions are normal and com plaints related to this noise are not covered by this warranty Damages resulting from 1 failure to install operate or maintain the appliance in accordance with the installation instructions operating instructions and listing agent identification label furnished with the appliance 2 failure to install the appliance in accordance with local building codes 3 shipping or improper handling 4 improper opera tion abuse misuse continued operation with damaged corroded or failed components accident or improperly incorrectly performed repairs 5 environmental conditions inadequate ventilation negative pressure or drafting caused by tightly sealed constructions insufficient make up air supply or handling devices such as exhaust fans or forced air furnaces or other such causes 6 use of fuels other than those specified in the operating instructions 7 installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT 8 modification of the appliance not expressly authorized and approved by HHT in writing and or 9 interruptions or fluctuations of electrical power supply to the appliance
48. ounds and fronts are shipped in separate packages The fiber logs may be packaged separately and must be field installed Report to your dealer any parts damaged in shipment particularly the condition of the glass Read all of the instructions before starting the insta llation Follow these instructions carefully during the installation to ensure maximum safety and benefit A WARNING y Hearth amp Home Technologies disclaims any responsibility for and the warranty will be voided by the following actions Installation and use of any damaged appliance or vent system component Modification of the appliance or vent system Installation other than as instructed by Hearth amp Home Technologies Improper positioning of the gas logs or the glass door Installation and or use of any component part not approved by Hearth amp Home Technologies Any such action may cause a fire hazard A WARNING x Keep appliance dry Mold or rust may cause odors Water may damage controls D Inspect Firebox Surface cracking or crazing of firebrick material is normal and expected The following types of cracks are acceptable and do not require replacement of the unit or the firebox Cracks that do not propagate entirely through the material Light fracture lines or spider webbing on the surface of the material Cracks that are less than 1 32 in wide and less than 3 in long If cosmetically unac
49. oved out area in log 1 LOG 6 SRV340 705 Place log 6 across log 1 and log 5 The notch in the bottom of log 6 rests in the carved out section on top of log 5 and the left end of the log sits in the horizontal carved out section of log 1 LOG 7 SRV740 707 Place log 7 across logs 1 and 3 in the grooved out areas as shown Quadra Fire QVI 30FB S 2020 910 Rev 6 09 F Glass Assembly WARNING Handle glass doors with care Inspect the gasket to ensure it is undamaged Inspect the glass for cracks chips or scratches Do NOT strike slam or scratch glass Do NOT operate appliance with glass door removed cracked broken or scratched Replace glass door assembly as a complete appliance Removing Glass Assembly There are two glass latches on the bottom of glass assembly To release glass assembly pull latch forward and allow to retract away from glass assembly Remove glass assembly after both latches have been released see Figure 11 16 Replacing Glass Assembly Replace the glass door on the appliance Fasten the latches on the glass frame FIREBOX SURROUND LOCATING TABS Figure 11 16 Glass Assembly G Air Shutter Setting Optimal flame appearance is dependent on the air shutter setting Adjustments should be made by a qualified technician NG QVI 30FB S Full open Quadra Fire QVI 30FB S 2020 910 Rev 6 09 25 1 Operating Instructions
50. r the Canadian Electric Code CSA C22 1 A 110 120 VAC circuit for this product must be protected with ground fault circuit interrupter protection in compliance with the applicable electrical codes when it is installed in locations such as in bathrooms or near sinks 4 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 2 Getting Started A Design and Installation Considerations Quadra Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside No additional outside air source is required CAUTION Check building codes prior to installation Installation MUST comply with local regional state and national codes and regulations Consult insurance carrier local building fire officials or authorities having jurisdiction about restrictions installation inspection and permits Quadra Fire gas inserts are designed for recessed installa tions into solid fuel masonry or factory built non combustible fireplaces that have been installed in accordance with the National Provincial State and local building codes Prior to installing the gas insert Have the chimney and adjacent structure inspected and cleaned by qualified professionals Hearth amp Home Technologies recommends that NFI or CSIA certified professionals or technicians under the direction of certi fied professionals conduct a minimum of a NFPA 211
51. rated the sheet metal are sharp and should be avoided Firebox 1 Inspect for paint condition warpage corrosion or perforation Contact Dealer for inspection EE __ __ 4 Check for smooth lighting and ignition carryover to all ports Verify there is no ignition delay 9 8 Verify manifold and inlet pressures Adjust regulator as required Inspect pilot flame strength Clean or replace orifice as necessary 4 Verify maintenance of proper clearance to combustible household objects 11 Verify millivolt output Replace as necessary Venting 1 Inspect venting for blockage or obstruction such as bird nests leaves etc 2 Confirm that termination cap remains clear and unobstructed by plants etc 3 Verify that termination cap clearance to subsequent construction building additions decks fences or sheds has been maintained 10 Inspect thermocouple thermopile or IPI sensor rod for soot corrosion and deterioration Clean with emery cloth or replace as required 2 Replace batteries in remote transmitters and battery powered receivers 3 Verify batteries have been removed from battery back up IPI systems to prevent premature battery failure or leaking Quadra Fire QVI 30FB S 2020 910 Rev H 6 09 33 1 Reference Materials A Appliance Dimension Diagram Dimensions are actual appliance dimensions Use for reference only For framing dimensions and clearances refer to Section 3 9 9 16 in
52. s carefully 5 The pilot and main a NoLP in tank Check the LP propane tank Refill the fuel tank burner extinguish while in operation Inner vent pipe leaking exhaust gases back into Check venting system for damage Replace repair e System improperly assembled pipe sections c Glass too loose and air tight packet leaks in Replace glass panel assembly corners after usage d Bad thermopile or thermocouple Replace if necessary e Improper vent cap installation Check for proper installation and freedom from debris or blockage 6 Glass soots a Flame impingement Adjust the log set so that the flame does not exces sively impinge on it b Improper air shutter setting Adjust the air shutter located on the control panel c Debris around air shutter Inspect the opening at the base of the burner NO MA TERIAL SHOULD BE PLACED IN THIS OPENING 7 Flame burns blue a Insufficient oxygen being supplied Ensure that the vent cap is installed properly and free and lifts off burner of debris Ensure that the vent system joints are tight and have no leaks Ensure that no debris has been placed at the base of or in the area of the air holes in the center of the base pan beneath the burner Ensure that the glass is tightened properly on the unit particularly on top corners Quadra Fire QVI 30FB S 2020 910 Rev 6 09 31 14 Maintaining and Servicing Appliance A Maintenance Tasks Although the frequen
53. tion when servicing controls Wiring errors can cause improper and dangerous operation Verify proper operation after servicing A WARNING Shock hazard Replace damaged wire with type 105 C rated wire Wire must have high temperature insulation C Installation for Fan Optional On units already installed removal of decorative front surround and gas insert is required Detach flexible liner from back of unit if insert is installed Remove the four screws on the cover plate see Figure 9 3 POWER CORD Figure 9 3 Bend up the tabs on the base pan see Figure 9 4 Place the blower in between the bend up tabs Install and wire the blower per instruction shipped with the fan The ground wire of the fan can clip on the side of the base pan Reinstall the cover plate back on the unit Make sure the fan does not make contact with the back wall to prevent noise from vibration 18 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 VARIABLE SPEED CONTROL JUNCTION BOX BLK GROUND BLOWER RECEPTACLE TEMPERATURE SENSOR SWITCH BLK GRN 110 120 VAC NOTE IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED IT MUST BE REPLACED WITH TYPE 105 C RATED WIRE BEND UP TABS Figure 9 4 Fan Wiring Diagram BLOWER JUNCTION TEMPERATURE SENSOR SWITCH SPEED CONTROL RHEOSTAT GROUND WIR
54. to seal off vents A WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury SEALANT ADHESIVE A WARNING Figure 7 2 W Explosion Risk Trim chimney top plate to minimize excess overhang or Combustion Fume Risk bend over flue tile see Figure 7 2 Connect vent sections per installation instructions Place 3 8 inch bead of 300 F silicone on flue tile top The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate C Placing Securing and Leveling the Connect exhaust vent pipe ONLY to exhaust starting collar Appliance and termination cap center collar Connect inlet air vent ONLY to inlet air collar on appliance Install insert without surround attached into existing and either the termination cap inlet air collar OR terminate fireplace while pulling collar slide plate forward within chimney Install gas line into hole provided on insert side Do NOT allow vent to sag below connection point to appliance If applicable install remote control wires into insert side see Section 6 F Secure collar slide plate to appliance by placing locking handle into position with locking tabs see Figure 7 1 and secure with 8 screw Level the appliance from side to side and front to back If necessary
55. trol Knob 571 534 Bracket Valve 773 147 38 Quadra Fire QVI 30FB S 2020 910 Rev 6 09 D Limited Lifetime Warranty Hearth amp Home Technologies Inc LIMITED LIFETIME WARRANTY Hearth amp Home Technologies Inc on behalf of its hearth brands HHT extends the following warranty for HHT gas wood pellet coal and electric hearth appliances that are purchased from an HHT authorized dealer WARRANTY COVERAGE HHT warrants to the original owner of the HHT appliance at the site of installation and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase that the HHT appliance will be free from defects in materials and workmanship at the time of manufacture After installation if covered compo nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period HHT will at its option repair or replace the covered components HHT at its own discretion may fully discharge all of its obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product itself The maximum amount recoverable under this warranty is limited to the purchase price of the product This warranty is subject to conditions exclusions and limitations as described below WARRANTY PERIOD Warranty coverage begins on the date of installation In the case of new home co
56. ures Combustible materials may ignite E Frequently Asked Questions SOLUTIONS This is a result of gas combustion and temperature variations As the appliance warms this Condensation on the glass NN condensation will disappear Blu flames This is a result of normal operation and the flames will begin to yellow as the appliance is al lowed to burn for 20 to 40 minutes When first operated this appliance may release an odor for the first several hours This is Odor from appliance caused by the curing of the paint and the burning off of any oils remaining from manufacturing and might set off home smoke detectors This is a normal result of the curing process of the paint and logs Glass should be cleaned Film on the glass within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing process A non abrasive cleaner such as gas fireplace glass cleaner may be necessary See your dealer Noise is caused by metal expanding and contracting as it heats up and cools down similar to Metallic noise the sound produced by a furnace or heating duct This noise does not affect the operation or longevity of the appliance Is it normal to see the pilot flame burn continually In a standing pilot system the pilot will always stay on Quadra Fire QVI 30FB S 2020 910 Rev 6 09 29 1 Troubleshooting With proper installation operation and maintenance your gas appliance will provid
57. way Do not operate the appliance with panel s removed cracked or broken Replacement of the panel s should be done by a licensed or qualified service person NOT FOR USE WITH SOLID FUEL For use with natural gas and propane A conversion kit as supplied by the manufacturer shall be used to convert this appliance to the alternate fuel Also Certified for Installation in a Bedroom or a Bedsitting Room For assistance or additional informa tion consult a qualified installer ser vice agency or the gas supplier For additional information on operating your Hearth amp Home Technologies fireplace please refer to www fireplaces com FoR YOUR SAFETY LLL L_I LIGHTING READ BEFORE LIGHTING INSTRUCTIONS Turn off all electric power to the appliance Push in gas control knob slightly and turn clockwise 9 7 Tu to OFF o ol 9 NOTE Knob cannot be turned from PILOT to OFF unless knob is pushed in slightly Do not force 3 Wait five 5 minutes to clear out any gas Then smell for gas including near the floor If you smell gas STOP Follow in the Safety Informa tion located on the left side of this label If you don t smell gas go to next step 4 Find the pilot The pilot is inside combustion chamber next to the main burner Turn knob on gas control counter clockwise 7 y to PILOT Push in control knob all the way and

Quadra-Fire QVI-30FB-S User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents