QSC WL2102 User's Manual
Contents
1. Standard L track Stacking the Stacking Frame The Stacking Frame comes with two aluminum I bars used for aligning and securing the frame to QSC s 215SB or 215PCM subwoofer To use the I bars simply slide each one into the small frame s L track and secure with a stud fitting Then turn the frame over l bars on the bottom and slide the exposed I bars into the subwoofer s L track Secure the l bar with a stud fitting Note that the stud fittings used are not required to be load rated as they only retain the l bars from moving laterally I beam stacking bar slide into L track on Stacking Frame then align and slide into L track on subwoofer cabinet QSC 215PCM or 215SB subwoofer 215SB or PCM cabinet use the I beam inserts 1 When stacking a Stacking Frame on top of QSC s in each L track to assure proper alignment and to firmly secure the frame to the 215 cabinet Secure using stud fittings Do not stack more than four 4 enclosures on a Stacking Frame Care We suggest wiping down all screws pins hardware and frames with LPS Dry Film Lube or Starrett M1 All Purpose Lube before and after outside gigs to help prevent oxidation This will not only prevent the formation of rust and other oxides but also provide lubrication adding to the longevity and ease of use of the WideLine product Configuration Frequency Response Frequency Range Sensitivity Nom2. 8 MF UNSHADED SELECT switch TRI AMP BI AMP Switch TRI AMP Shading network is NOT applied shading must be provided by upstream signal processing Connect the full range input signal to pins 1 and 1 connect the shaded pro cessed signal to pins 2 and 2 To flip shaded transducer location use the MF UNSHADED SELECT switch or alter sig nal processing Default MF UNSHADED SELECT switch posi tion for three way mode is position A if put in position B connections per Table 1 to LF transducers A and B are inter changed BI AMP The full range LF input is applied to pins 1 and 1 and the 6dB per octave shading network is applied to one of the LF transducers using the MF UNSHADED SELECT switch MF UNSHADED SELECT Switch The WideLine is a three way design shaded non shaded and high frequency with shading provided by a passive network in BI AMP mode or upstream signal processing DSP in TRI AMP mode This allows switch position selection for use as either house left or house right without the need to invert boxes BI AMP The shading switch allows either low frequency transducer to be selected as the shaded unit bass only by inserting a 6dB per octave network The switch handle points to the side of the unshaded full range low frequency trans ducer TRI AMP The internal 6dB per octave network in NOT applied to either LF transducer Shading is accomplished with signal processing The switch
3. of splay The ball lock pin is inserted Rear link into the 6 position in the rear block while passing through the Rear link attached to 3 pin hole in the link The total splay is the 6 indicated on attached to achieve a9 the block plus the 3 additional from the link position for a achieve an H F splay total of 9 In this manner 1 increments can be attained start 8 splay H 7 between Talo ing with 3 0 block location and 3 link arm location between 2 rH HF enclosures enclosures q Fly Grid and Stacking Frame qs There are two array frames available for the WideLine system D m 10 The Fly Grid is used for suspending larger arrays The Fly Grid may be inverted and used for ground stacking The Stacking Frame is a compact and easier to handle frame H for use as a small array or stacking frame This frame will eas ily sit on ground deck stacked bass enclosures or it can be ee 7 used at those smaller events to suspend clusters from the stage trusses Bolt on receiver Fly Grid tube and 5 16 inch diameter 1 25 inch A Use only 5 16 inch diameter x 1 25 inch long ball long ball lock pin lock pins on front receiver tubes The three pick up rails allow for any number of rigging solu tions to fit the most demanding venues The rails are drilled for industry standard 5 8 inch shackles lt 31 6 803mm _ gt Fly Grid Large Array Frame 14 8 376mm Do not stack more than
4. the event that this product was manufactured for export and sale outside of the United States or its territories then this limited war ranty shall not apply Removal of the serial number on this product or purchase of this product from an unauthorized dealer will void this limited warranty Periodically this warranty is updated To obtain the most recent version of OSC s warranty statement please visit www gscaudio com Contact us at 800 854 4079 or visit our website at www qscaudio com OSC QSC Audio Products Inc 1675 MacArthur Boulevard Costa Mesa California 92626 USA 2006 QSC and the QSC logo are registered with the U S Patent and Trademark Office
5. Main Number 714 754 6175 Sales amp Marketing 714 957 7100 or toll free USA only 800 854 4079 Customer Service 714 957 7150 or toll free USA only 800 772 2834 Facsimile Numbers Sales amp Marketing FAX 714 754 6174 Customer Service FAX 714 754 6173 World Wide Web www qscaudio com E mail info qscaudio com service qscaudio com Warranty Disclaimer USA only other countries see your dealer or distributor QSC Audio Products Inc is not liable for any damage to amplifiers loudspeakers or any other equipment that is caused by negligence or improper installation and or use of this signal processing product While QSC has endeavored to develop and produce the most dependable and robust network audio product for your use due to the myriad of network situations and equipment that may be encountered in its implementation QSC cannot be held responsible for network conflicts and associated consequences that may result For this reason OSC strongly recommends that the network used for implementation of OSControl products be completely separate from all other networks data or otherwise As such should you elect to integrate OSControl products with your existing network sys tem all risks attendant to such integration of OSControl products with your existing network or network systems are assumed by you While QSC strives to provide the highest quality technical solutions for networked audio products in no event will QSC or i
6. asc ISIS WideLine Loudspeaker User Manual Manual del usuario para los altavoces ISIS WideLine Mantel de l utilisateur des haut parleurs ISIS WideLine ISIS WideLine Lautsprecher Benutzerhandbuch ISIS WideLine HABA FH WL2102 Cored Composite Enclosure WL2102 w Birch Plywood Enclosure Stacking Frame Fly Grid UT TD 000227 00 rev B IMPORTANT SAFETY PRECAUTIONS Install in accordance with OSC Audio Product s instructions and under the supervision of a licensed Professional Engineer WARNING Before placing installing rigging or suspending any speaker product inspect all hardware suspension cabinets transducers brackets and associated equipment for damage Any missing corroded deformed or non load rated component could significantly reduce the strength of the installation placement or array Any such condition severely reduces the safety of the installation and should be immediately corrected Use only hardware which is rated for the loading conditions of the installation and any possible short term unexpected overloading Never exceed the rating of the hardware or equipment Consult a licensed Professional Engineer regarding physical equipment installation Ensure that all local state and national regulations regarding the safety and operation of suspension equipm
7. de of the United States or its territories then this limited war ranty shall not apply Removal of the serial number on this product or purchase of this product from an unauthorized dealer will void this limited warranty Periodically this warranty is updated To obtain the most recent version of QSC s warranty statement please visit www gscaudio com Contact us at 800 854 4079 or visit our website at www qscaudio com Copyright 2006 QSC Audio Products Inc QSC is a registered trademark of QSC Audio Products Inc Speakon is a registered trademark of Neutrik and the names of Neutrik products referenced herein are either trademarks and or service marks of Neutrik M isa registered trademark of Starrett The L S Starrett Company LPS is a registered trademark of LPS Laboratories All trademarks are the property of their respective owners QSC and the QSC logo are registered with the U S Patent and Trademark Office Introduction The WideLine loudspeaker system has been designed to pro vide a compact system that has unique power handling fre quency response Its primary uses include ballrooms theatres night clubs houses of worship and small to medium size events for the corporate and industrial markets WL2102 enclosures are constructed of lightweight cored com posite and weigh 70 Ib 31 8 kg WL2102 w enclosures are constructed of birch plywood and weigh 83 Ib 37 7 kg The hardware allows for simple
8. ducer or damage may result INPUT OUTPUT PARALLEL 0 o E f D Table 1 Input Connector Wiring BI AMP and TRI AMP Modes 0 eo BI AMP TRI AMP TRI AMP Internal Shading MF UNSHADED SELECT MF UNSHADED SELECT Pin Network Inserted in Switch Position A Switch Position B Signal Path Use External Processing Use External Processing for Shading for Shading 1 LF LFA LF B 1 LF LFA LF B 2 Not Used LF B LFA 2 Not Used LF B LFA 3 Not used Not used Not used 3 Not used Not used Not used 4 HF HF HF 4 HF HF HF Neutrik NL8FC Cable Connector Pinout Shown at right is a diagram of the pin designation inside the Neutrik NL8FC connector This infor NL8FC pin designations Plug mation is for reference only Diagram is of the connector as viewed from the wire insertion end viewed from the wiring side Rigging A Rules for Suspension e Correct use of all suspension hardware and components is imperative in sound system rigging and deployment e Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits e Research local codes and regulations to fully understand the requirements for suspended loads in the venue in which the equipment is to be suspended e Use only shackle holes for suspension of array e Be absolutely certain of the integrity of any structural member intended to supp
9. eight 8 enclosures on the 37 0 940mm Left pickup rail Center pickup rail Right pickup rail E E Z 7 7 7 amp 7 3 3 3 3 5 53 38 a MW Open end for bolt access Fly Grid The mounting plate and link bar are located on the bottom side of the frame assembly Use this link for attaching the rear of the first enclosure The frame allows for up or down angle options for use with either stacking or suspending The 4 normal locations on the link system will yield a net 0 vertical inclina tion Use 4 link location w 7 0 vertical inclination Stacking Frame Do not stack more than four 4 enclosures on a A Stacking Frame Use only 5 16 diameter x 1 25 long ball lock pins on front receiver tubes The Stacking Frame interfaces with QSC s 215PCM or 215SB subwoofer in either a stacked or flown configuration The stack moved to the opposite side of the frame o00000000000000000 O m oooo0oo00 5 16 inch diameter 1 25 inch long ball lock pins member for use The small frame is con structed using standard L track for rig ging ing bumpers on the frame may need to be 25 7 653mm p Stacking bumpers align with stand sockets of QSC Pa 215PCM subwoofer DS O ar 495mm Bumpers _ gt gt
10. ent are understood and adhered to Warranty USA only other countries see your dealer or distributor Disclaimer OSC Audio Products Inc is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and or use of this loudspeaker product OSC Audio Products 3 Year Limited Warranty OSC Audio Products Inc OSC guarantees its products to be free from defective material and or workmanship for a period of three 3 years from date of sale and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use provided the unit is returned to our factory or one of our authorized service stations via prepaid trans portation with a copy of proof of purchase i sales receipt This warranty provides that the examination of the return product must indicate in our judgment a manufacturing defect This warranty does not extend to any product which has been subjected to misuse neglect accident improper installation or where the date code has been removed or defaced QSC shall not be liable for incidental and or consequential damages This warranty gives you specific legal rights This limited warranty is freely transferable during the term of the warranty period Customer may have additional rights which vary from state to state In the event that this product was manufactured for export and sale outsi
11. handle points to the side of the non shaded full range low frequency transducer ONLY IF the full range signal is applied to pins 1 and 1 and the shaded signal to pins 2 and 2 Default position for TRI AMP mode is position A if put in position B connections to LF transducers A and B are interchanged TRI AMP BI AMP B gt MF UNSHADED SELECT MF UNSHADED SELECT Switch BI AMP Mode Pins 1 1 3 LF Transducer A LF Transducer B Pins 2 2 not used Pins 3 3 not used Pins444 yx__ HF Transducer MF UNSHADED SELECT Switch TRI AMP Mode Pins 1 1 y LF Transducer A Pins 2 2 y LF Transducer B Pins 3 3 not used Pins 4 4 3y HF Transducer Input Connections The input connectors are a pair of Neutrik NL8 s wired in parallel Connections for bi amp and tri amp vary see Table 1 The pin designations for the NL8FC cable connector is shown for ref INPUT spec erence bottom right TRI AMP Note In TRI AMP mode the MF UNSHADED SELECT switch position deter A mines the input connector wiring Unexpected results may occur if switch positions and wiring are not strictly controlled Z The WideLine loudspeaker is not equipped with a crossover network All signal im processing must be done before connecting audio power to the loudspeaker Do A V not connect full range audio to the high frequency trans
12. ight 87 Ib 39 5 kg Software EASE Focus line array modeling software tool available visit www qscaudio com or contact QSC s Technical Services for DSP files for both OSControl net and Signal Manager Ball lock Pins WL2102 Nylon Lanyard 5 16 inch dia x 0 75 inch long t handle p n SR 000052 00 Rear Link and Front Tube Pin WL2102 w 7 inch Stainless Steel Lanyard 5 16 inch dia x 0 75 inch long t handle p n HW 000106 00 Rear Link Pin 5 5 inch Stainless Steel Lanyard 5 16 inch dia x 0 75 inch long t handle p n HW 000126 00 Front Tube Pin Array Frames Nylon Lanyard 5 16 inch dia x 1 25 inch long t handle p n SR 000126 00 Array Frame Pin NOTES 1 with recommended DSP settings 2 2 hours AES 1984 2 method 80 800 Hz 3 2 hours AES1984 2 method 1 000 10 000 Hz 11 Dimensions WL2102 and WL2102 w NOTE Composite enclo sures have approximately 1 of draft on the enclosure sides the birch plywood enclosures do not Handle orientation may vary between composite and plywood enclosures 1 gt 7 7 196mm i L Lg 20 4 518mm gt Oe 10 75 273mm 27 5 699mm gt lt 25 0 635mm 3 M 10 1 lt 257mm 4 26 8 681mm How to Contact OSC Audio Products Mailing address QSC Audio Products Inc 1675 MacArthur Boulevard Costa Mesa CA 92626 1468 USA Telephone Numbers
13. inal coverage Nominal Impedance Transducers Recommended Amplifier Power Enclosure Type Material Finish Grille Connectors Attachment points Weight Accessories Array Frames System Specifications subject to change without notice Three way bi amp or tri amp 55 18 000 Hz 3 dB 48 20 000 Hz 10 dB LF 98 dB 1W 1m HF 107 5 dB 1W 1m Horizontal 140 degrees Vertical Dependant on cumulative splay angle LF bi amp mode 8 Ohm tri amp mode 16 Ohm HF 16 Ohm LF Two 10 inch 254mm long excursion high power 3 inch 76mm voice coil 16 Ohm 400W each HF 3 0 inch 76mm diaphragm 1 4 inch 36mm exit 16 Ohm neodymium compression driver on proprietary patent pending waveguide sows HF 300W MF 700W tri amp mode LF 700W tri amp mode LF MF 1400W bi amp mode Bass reflex ported trapezoidal WL2102 cored composite laminate WL2102 w birch plywood Black or white texture coat Powder coated steel Two Neutrik NL8 wired in parallel Self contained rigging configuration Front receiver tubes contain captive articulated joints knuckle and ball lock pins on lanyards Rear mounting block has integral mounting link and ball lock pin on lanyard WL2102 70 Ib 31 8 kg WL2102 w 83 Ib 37 7 kg Stacking Frame For suspended or stacking applications on QSC s 215SB or 215 PCM subwoofer Frame weight 33 Ib 15 0 kg Fly Grid For suspended or stacking applications Frame we
14. mal 0 position and with a 3 at the 3 position The additional ball lock pin hole located approximately mid way on the link is used for storing the link when folded into the enclosure s block for storage The link may be pinned in place at the 0 or 8 location on the block when rotated into the storage position Front Articulated Joint Slide the joint out of the receiver tube by sliding the retaining screw upward then lock in place using the ball lock pin Rear Link Remove the ball lock pin from the storage position then rotate the link downward to the adjacent enclosure Lock in place using the ball lock pin Adjusting the Angle Between Enclosures Splay The illustration shows the rear pin block of two enclosures o JM joined by the upper enclosure s rear link arm 2 HH 2 a Hm m a Use the first pin location closest to the end on the link arm for setting in normalized 2 increments The left side example shows two enclosures linked for 8 of splay The ball lock pin is inserted into the 8 position in the rear block while passing through the normal pin hole in the link When the 3 location is used an additional 3 are added to the normalized location The right side example shows two enclosures linked for 9
15. of front left right captive articulated joints and a single rear link bar Articulation is in 2 incre ments using the first location on the link bar With the use of the second location 1 degree increments can be obtained starting at 3 The total available angular increments are 0 2 3 4 5 6 7 8 9 and 10 All pieces and locking pins remain with the enclosures No ancillary items are needed to suspend the enclosures from the WideLine array frame All ball lock pins are equipped with a lanyard to help prevent loss Front Articulated Joint Knuckle Hardware Expose the end of the articulated joint by locating the joint s retaining screw protruding from the front of the receiver tube and sliding it upward The front captive joint will slide upward from the enclosure s receiver tube The exposed end of the articulated joint can now be inserted into the adjacent enclosure s receiver tube and locked into position by a locking pin This is repeated for each side of the enclosure Then the rear link bar can be rotated into position and pinned at the chosen degree increment Rear Link Angle Adjust Hardware The rear link is stored with the link folded between the sides of the block To expose the link remove the ball lock pin and rotate the link into the desired position Once positioned the link is secured using the ball lock pin of the adjacent enclo sure The rear link is marked with a thin white line at the nor
16. ort suspended loads Hidden structural members can have hidden structural weakness e Consult a professional mechanical or structural engineer licensed in the jurisdiction of the sound system installation to review ver ify and approve all attachments to the building or structure e Never assume anything owner or third party supplied suspension attachment points may not be adequate for the loads to be sus pended e Employ the services of a professional rigger for hoisting positioning and attaching the equipment to the supporting structure e Always inspect all components enclosures suspension brackets pins frames bolts nuts slings shackles etc for cracks wear deformation corrosion missing loose or damaged parts that could reduce the strength of the assembly before lifting Discard any worn defective or suspect parts and replace them with new appropriately load rated parts Shock Loading When a load is either moved or stopped its static weight is magnified Sudden movements can magnify the static weight several times This magnification of static weight is termed shock loading Shock loading poses a danger to equipment and workers The effects of shock loading can be instantaneous or they may remain undetected unless the equipment is visually damaged Avoiding shock loading requires careful planning and knowledge of equipment rigging and lifting practices Shock loading of equipment and structures is usually confined
17. shaded transducer handles the mids This provides smoother pattern control at the mid high cross over With selectable shading the enclosures can be used as house right or left by flipping the switch not the enclosure WideLine users can also use a software tool called EASE Focus to aid in the design and implementation of a WideLine array EASE Focus can calculate the number of enclosures required for a given space venue determine the optimum splay angle between those enclosures calculate at what angle to set the array frame in a single variable pick point or fixed suspension point application and predict the acoustical response and sound pressure levels throughout the venue ina two dimensional illustration The software is available sepa rately downloadable from the OSC website or contact OSC for more information Like all OSC Audio products WideLine design focuses on accurate audio performance rapid set up and reduced labor requirements Ease of transportation assembly use and self contained rigging hardware make WideLine the clear choice FRONT grille removed 1 Receiver tube front left and right with captive articulated joint inside receiver tube and ball lock pins 2 Low frequency transducer B 3 High frequency transducer aper ture 4 Low frequency transducer A REAR 5 Input output connectors NL8 6 Rear link mounting block and ball lock pin 7 TRI AMP BI AMP selector switch
18. to lifting and installation but natural forces winds earthquakes can impose shock loads several times the static load This is why structures and suspension equipment must be capable of supporting sev eral times the weight of the equipment suspended WideLine Working Load Limits and Design Factors Table 1 lists the WideLine suspension components and provides Working Load Limit data at various Design Factors The tabulated Design Factors are for static loads only The choice of which Design Factor to use will depend upon the jurisdiction and venue of instal lation as well as the conditions of suspension Dynamic conditions are determined by unknown installation specific factors and should be referred to a Licensed Structural Engineer for clarification before proceeding with any suspension of the equipment The data presented is based upon the listed component weights Component Weight 4 1 Design Factor 5 1 Design Factor 7 1 Design Factor 10 1 Design Factor WL2102 70 Ib 31 8 kg 2300 Ib 1040 kg 1800 Ib 836 kg 1300 Ib 597 kg 920 Ib 418 kg WL2102 w 83 Ib 37 7 kg 2500 Ib 1130 kg 2000 Ib 909 kg 1400 Ib 649 kg 1000 Ib 455 kg Fly Grid 87 Ib 39 5 kg 1800 Ib 794 kg 1400 lb 636 kg 1000 Ib 455 kg 700 Ib 318 kg Stacking Frame 33 Ib 15 0 kg 1800 Ib 794 kg 1400 Ib 636 kg 1000 Ib 455 kg 700 Ib 318 kg in WideLine enclosures use a three point suspension system The system consists
19. ts suppliers be held liable for any damages consequential incidental or otherwise including any claims for lost profits and or savings resulting from any attempted integration of QSControl products with your networking systems No agent employee or representative of OSC has any authority to alter or modify in any manner the disclosures and recommendations set forth herein QSC Audio Products 3 Year Limited Warranty QSC Audio Products Inc OSC guarantees its products to be free from defective material and or workmanship for a period of three 3 years from date of sale and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use provided the unit is returned to our factory or one of our authorized service stations via pre paid transportation with a copy of proof of purchase i e sales receipt This warranty provides that the examination of the return prod uct must indicate in our judgment a manufacturing defect This warranty does not extend to any product which has been subjected to misuse neglect accident improper installation or where the date code has been removed or defaced OSC shall not be liable for inci dental and or consequential damages This warranty gives you specific legal rights This limited warranty is freely transferable during the term of the warranty period Customer may have additional rights which vary from state to state In
20. vertical splay angle adjustment of 0 2 3 4 5 6 7 8 9 and 10 between enclosures Two array frames are available The Stacking Frame is for sus pended applications or stacking on top of OSC s 215SB or 215PCM subwoofers The large array frame is for suspended or ground stack applications The WideLine system is suitable for stand alone applications as a full range articulate high fidelity sound reinforcement product with the ability to reproduce almost any musical pro gram without subwoofers or bass modules It has bass response to 55 Hz 3 dB in a small format package Its 3 way bi amp or tri amp design keeps required amplification to a min imum WideLine s exceptionally wide dispersion practically elimi nates the need for side or fill hangs when used as the main array Its wide dispersion also provides enhanced cover age when used as a center cluster or as a downfill or under hang enclosure when used with larger format line array systems Wide dispersion is accomplished with a 3 inch 76mm dia phragm 1 4 36mm exit neodymium high frequency driver mounted on a proprietary patent pending multiple aperture diffraction slot waveguide This device is the ideal linear source needed for wide angle line array performance Internal mid frequency shading can be switched to either 10 254mm transducer Both transducers handle the low frequen cies but only the non
Download Pdf Manuals
Related Search