Proficient Audio Systems M4 User's Manual
Contents
1. The PMK 13 buttons and PMKIR 12 buttons are the master keypads and must be used in each system As mentioned earlier the M4 comes with a pre configured version of the PMKIR for the convenience of the installer It is usable right out of the box in conjunction with a default project that is factory programmed into the M4 The PMKIR includes an IR receiver and has one less function button but is otherwise identical to the PMK The PNK Numeric 16 buttons and PFK Function 14 buttons keypad modules can be thought of as slaves to the master unit they will not work alone providing additional key locations for numeric and function commands SINGLE GANG Figure 4 PMKIR included PMKIR Master Keypad included with the M4 Single Gang Set Up 1 PMKIR Source Function Buttons Six of this set of eight buttons are programmed as source select for the M4 When the system is off all buttons have a background green color When a source button is pressed it turns to a low level red color to show that it is the active source and the system is on 2 Keypad Expansion Terminal This 16 pin header terminal is used to inter connect the optional numeric and function keypad modules for expansion as needed A 3 connector ribbon cable is packed with each module for making these connections 32. may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may Contact Closures dry 2A 30V AC DC Max be required If mounting surface modification is required Proficient Audio Systems assumes no responsibility or liability for such modification All replaced parts and product become the Phone Page In Audio Line Level gt 22 kQ Voltage Impedance Doorbell Status In1 amp 2 10mA 12V AC DC 3V 30V AC or DC Common IR Out HI high power LO emitter power 9 V Active High 82 Q 110 mA Peak 9 V Active High 670 Q 13 mA Peak Zone IR Outs Voltage Impedance 9 2 V Active High 620 Q 13 mA Peak Source IR Outs and loop 11 5 V Active High 390 Q 29 mA Peak Voltage Impedance Common Status Out 9 5 V 100 mA 0 12V DC property of Proficient Audio Systems Products replaced or repaired under this Warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This Warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use volt age inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by Proficient Audio Systems This Warranty also excludes normal cosm
3. KEYPAD BUTTONS 1 The keypads have a pre installed set of buttons in place These may not match the source and function arrangements you need or desire To change them release the tabs on each end of the keypad Figure 8 and remove the decorator insert panel exposing the key buttons Figure 9 2 Starting with the Zone 1 PMKIR master keypad and using the extra buttons supplied if needed move and place the source and function buttons in the arrangement you want See Figure 10 When you finish the arrangement replace the decorator insert panel over the buttons being careful to see that the buttons align correctly with the panel openings Press the panel down until the tabs snap into place 3 Repeat these steps for each of the other zone master keypads Each zone can have its own unique configuration but it is best to keep them as similar as possible to simplify programming and operation 4 In the same way configure the buttons on the numeric and function keypads not included that you may chose to use in some zones 5 Connect all keypads to their assigned zones on the M4 as shown in Figure 7 Be sure to strip then connect the various colored CAT5 leads to the correct terminals on each keypad end Refer to Figure 15 Figure 8 Release Tab Figure 10 Moving and Placing Buttons 15 Figure 11 Ribbon Cable PMKIR Right Figure 13 RJA 1 1 Adapter Figure 14 RJA 1 1 Attached to Keypad and C
4. AT5 KEYPAD HOOKUP NOTE The numeric and function keypads will not work on their own They must be connected to a master keypad using the 3 connector ribbon cable supplied included with each model The cable is symmetrical so it can be connected with the red striped side up or down to best fit the configuration Figure 11 shows it connected so that the PMKIR master keypad will be to the right of the PNK numeric and PFK function keypads when mounted whereas Figure 12 places the PMKIR to the left Figure 15 Using CAT5 Cable to Connect PMKIR Keypads to M4 CAUTION ADDRESS ENT a Systems PMKIR Master Keypad with IR Receiver KEYPAD EXPANSION Riverside CA USA Made in China for T568A and orange White Brown CAT5 Cable Blue 1 000 305m Max White Blue Use Twisted Pair Brown for 485A amp 485B White Orange Colors shown are based on PROFICIEN T568B RJ45 termination wiring termination Twisted Pair NOTE 1 If you want to use RJ45 connectors for connecting the CAT5 cable to the keypads you can do so by using the Proficient model RJA 1 1 RJ45 to Wire Pin Adapters See Figure 13 and Figure 14 Simply insert the RJA 1 1 pins into the keypad s connection terminals and snap the levers in place Be sure to orient them correctly as shown M4 Keypad Connector ere Giantess ce I e VC NVC IR OUT es SEE CHART BELOW
5. Address Switch A unique hex address must be set for each master keypad when connected on a common bus within a single zone Unique addresses are not required zone to zone It provides up to 16 addresses 0 to F 4 Snap Tabs These tabs hold the decorator style insert panel to the metal mounting plate and are easily released for custom changing of the buttons 5 Mounting Plate Standard plate allows the keypad module to be attached to standard in wall J Boxes using the two screws provided Allows attachment of standard decorator type cover plates also screw less snap on plates 6 IR Receiver Lens Version PMKIR includes Proficient s exclusive ANS IR receiver built in It allows the use of a handheld remote for control of system components 7 Connection Terminals for CAT5 home run termination Relay and Relay for future use 12V Powers the keypad including the internal IR receiver on model PMKIR Includes reverse voltage protection Data Sends IR control signals for control of system components GND Return for power IR signal and data 485 A 485 B Balanced bi directional system communications data 8 Function Buttons These lower four buttons can be programmed for any function except source select DOUBLE GANG Figure 5 PMKIR included Rear View PMKIR Ma
6. C when the last zone is turned OFF The max output of this jack is 100 mA at 9 5V DC IR OUT JACKS These 3 5mm mini phone jacks one for each source provide dedicated IR output to specific source components When a source is selected on a keypad IR function commands are routed directly to that source This prevents cross control interference between two or more sources that have identical IR commands IR LOOP JACKS These six 3 5mm mini phone jacks one for each source are provided exclusively for zone expansion capability when using two or more M4 controllers They permit the source IR signals from the added zones to be carried to the source component emitters L amp R AUDIO IN amp LOOP JACKS These RCA jacks four for each source provide audio signal inputs and buffered loop outputs for each source The buffered outputs can be used to drive local components or loop the signals to the additional zone inputs of other M4 controllers when using them for source expansion AWG Internal relay contacts are rated at 2A 30V AC or DC L amp R PRE OUT JACKS These RCA jacks provide line level audio outputs for driving external power amplifiers for additional rooms within zones where needed 2 L L R R EENE mo KEYPAD ZONE INPUTS These RJ45 terminals allow for easy connection of the inter room wiring from keypads in the various rooms Normally this is accomplished using CAT5 cable with home run lengths
7. KIR includes Proficient s exclusive ANS IR receiver built in It allows the use of a handheld remote for control of system components 7 Connection Terminals for CAT5 home run termination Relay and Relay for future use 12V Powers the keypad including the internal IR receiver on model PMKIR Includes reverse voltage protection Data Sends IR control signals for control of system components GND Return for power IR signal and data 485 A 485 B Balanced bi directional system communications data 8 Function Buttons These lower four buttons can be programmed for any function except source select 9 Numeric and Function Buttons Require programming via Proficient Editor All buttons glow background green and can be configured to go off after a set time or stay on via Proficient Editor eee TRIPLE GANG Figure 6 PMKIR P PFK included optional optional 1 3 4 we OTO Po N D QG Soe qd p KO z 9 a 2 Fa a a Ed PROFICIENT Audio Systems PNK PACEICIENT Cc 4 PMKIR Master Keypad included with the M4 Triple Gang Set Up 1 PMKIR Source Function Buttons Six of this set of eight buttons are programmed as source select f
8. PROF ICIENT Audio Systems M4 QUICK START GUIDE Figure 1 M4 Front Panel Features PROFICIENT a MASTER POWER SWITCH When pressed in the M4 permits zones to be turned ON and OFF by keypad or touch panel commands BLUE INDICATOR LIGHT Blue indicates the master power switch is ON and one or more zones are active Red is OFF ZONE STATUS LEDS LED indicators and labels Four blue LEDs indicate that one or more zones are currently active M4 FEATURES M4 Multi Zone Audio Amplifier Controller The M4 is a four zone six source Audio Amplifier Controller It serves as the brains of the entire keypad system The M4 provides audio switching for six sources and 30W channel audio power amplifiers for four zones It also has connection termination facilities for the controlled whole house system RS 232 DATA I O Communication port EXPANSION PORTS RJ45 jacks provide for connection of specialized RS485 controlled products and for looping to additional M4 controllers for zone expansion capability CONTACT CLOSURE Provides a single pole dry relay contact to activate any device that can be controlled or triggered by a switch closure The closure can be programmed within Proficient Editor to be activated by keypad presses Command Library IR or within macros for Momentary Toggle and Open Close Paired operations Spring loaded terminals accept wire sizes from 28 to 14 PHONE PAGE IN JACK This jac
9. TU T568B Inter Room T568B Standard T568A Standard 16
10. all zones This means that commands from any keypad in any zone will execute regardless of previous command executions in other zones Figure 7 7 When a zone is first turned on the volume will be at a default medium background level After that it will come on at the last volume used prior to zone turn OFF 11 Speaker Feeds to Each Zone M4 SPECIFICATIONS Audio Sections General Rated Power Channel 30 Watts 20Hz 20kHz Power Consumption RMS 2 ch l i i Q r RMS 2 channels driven ito 8 0 No Signal idle 50 Watts THD 79 at rated power SA At 1 8 Rated Power 110 Watts Power Channel 45 Watts 1kHz 3 75 watts channel RMS 2 channels driven into 4 Q Input Sensitivity 300 mV For rated power max VC Input Impedance source inputs gt 22 kQ Input Overload source inputs 2 5 V Output Voltage Pre Outs 1 7 V VC Setting VC Max w 300 mV source inputs 810 mV NVC Setting Output Impedance pre outs lt 3000 Frequency Response 1 watt 8 O 20Hz 20kHz 1 5dB Channel Separation gt 50dB 10kHz Line Ratings 120V AC version 120V AC 1 8A Rear Panel Fuse 120V AC version T5AL 250V Line Ratings 230V AC versions 230V AC 0 9A Rear Panel Fuse 230V AC versions T2 5AL 250V 53 6 x 171 x 1514 148mm x 435mm x 394mm Dimensions H x W x D Weight 20 Ibs 9 1 kg Limited Two Year Warranty Proficient Audio Systems warrants t
11. ce components and plug them into the corresponding Source IR Outputs on the M4 WD Volume Down command Also serves as Bass p g p or Treble Down after first pressing BASS or TREB keys SPKRS e RE e CAUTION ne o RISK OF ELECTRIC SHOCK DO NOT OPEN C TEJER f J NOTE While in the Treble or Bass tone modes the selected Source button will blink at a medium rate to indicate the tone setting mode The tone setting mode is defeated by one press of any button other than the Tone and Volume buttons MUTE Set for Internal Preamp Muting Toggles ON OFF Pressing Source and Volume buttons also un mutes During Mute selected source key blinks slowly PWR Set as Zone Power OFF Will NOT turn the zone ON Press and Hold for two seconds turns all zones OFF Whole House Release button when blinking stops Source button then turns Amber in color indicating system is now in Whole House Party Mode Source selection Volume Control and Mute functions will now operate in all zones from the initiating zone only To transfer Whole House Party Mode control to another zone above steps are repeated from the desired zone To cancel Whole House Party Mode press and hold a Source button from the initiating zone for longer than two seconds until blinking stops NOTE Zones other than the initiating zone will have red active Source buttons and will operate as normal independent zones 6 Priority is set to ON for
12. e brains of the system taking key location data from the keypads to trigger the actual controlling IR RS232 and RS485 commands that are passed to all of the installed system components Programming is accomplished by the use of Proficient Editor a Proficient developed Windows software system A fourth item the optional Command Interface sold separately is an installer s tool for learning and teaching special IR commands that are not included in the Proficient Editor internal library KEYPAD GANG CONFIGURATIONS The M4 System comes with four single gang PMKIR pre configured keypads one for each zone as shown for the single gang version in Figure 3 The cover plates and the other configurations are optional Screw less Snap On type cover plates are also accommodated Each keypad comes with a set of factory installed default buttons plus a good variety of additional buttons The default buttons can be easily changed to meet the needs of the installation Single Gang Double Gang Triple Gang lt gt ew gt O0 eee eS GOGO IIED OO OO s a e 1 p lt gt bA a S gt EY Nv PMKIR PMKIR PNK PMKIR PNK PFK included included optional included optional optional Figure 3 The Keypad Gang Configurations Keypad Features The keypads come in four basic modules as shown
13. etic deterioration caused by environmental conditions This warranty will be void if the Serial Number on the product has been removed tampered with or defaced This Warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will Proficient Audio Systems be liable for any incidental or con sequential damages arising out of the use or inability to use the product even if Proficient Audio Systems or a Proficient Audio Systems Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed Warranty Some states do not allow limitation on the length of an implied warranty If the original retail PROFICIENT Audio Systems 940 Columbia Avenue Riverside CA 92507 877 888 9004 Fax 951 787 8747 proficientaudio com purchaser resides in such a state this limitation does not apply For technical inquiries please call 877 888 9004 or email us at techsupport proficientaudio com We are available to assist you every weekday except holidays between the hours of 7 00 a m and 5 00 p m PST 1301 72400 rev1 14 CONFIGURE THE
14. k provides input porting for audio feeds from door mikes or other forms of phone or doorbell paging The jack is programmable by Proficient Editor to turn on as events when triggered by the DOORBELL STATUS IN Jack Figure 2 M4 Rear Panel Features a EXPANSION PORTS a DOORBELL STATUS IN 1 amp 2 JACKS These 3 5mm mini phone trigger inputs work in conjunction with the PHONE PAGE IN jack When triggered the phone inputs can be turned on as programmed by Proficient Editor If audio paging is not required these 1 amp 2 jacks may also be pogrammed as STATUS inputs for power management of source or zone components They accept input levels of 3V to 30V AC or DC for the trigger ON condition The voltage level must drop below 1V AC or DC for the OFF condition RS232 CONTACT CLOSURE SOURCE 1 IO ok Loop 1h PRE OUT iS I I 0 7 NVC C KEYPAD ZONE 1 SPKRS DATA I O PHONE PAGE IN DOORBELL STATUS IN SOURCE 2 SOURCE 3 INPUTS INPUTS L R L R LOOP PRE OUT PRE OUT L I 1 k O Ff O NVC NVC IR OUT FUSE T5AL 250V C ae KEYPAD KEYPAD ZONE 2 ZONE 3 SPKRS SPKRS CONTROL PORT amp FIRMWARE UPGRADE SWITCH 3 5mm 4 circuit mini phone jack allows several control functions All keypad programming is accomplished via this port using Proficient Editor in conjunction with the mating Transfer Cable It also accommodates factory firmware updates i
15. n conjunction with the FIRMWARE UPGRADE OFF ON Switch Be sure to leave this switch in the OFF position at all times except as instructed within Proficient Editor when you are doing a firmware update Such updates ensure that you can always have the latest functionality improvements in the field Another function of this port is that you can control installed system components with bi directional data via touch panels or computers using RS232 protocol FIRMWARE COMMON UPGRADE Ko CONTROL PORT OFF ON IR OUT STATUS OUT 0 to 12V SOURCE 4 SOURCE 5 SOURCE 6 e Riverside CA USA SOA O Madein Taiwan 0 0 w L R lt AA ee I ok LOOP eel vc NVC 120V 60Hz 1 8A 7A CAUTION RISK E aes C E COMMON IR OUTPUT amp HI LO SWITCH 3 5mm mini phone jack provides a common IR output derived from all of the zone IR inputs and from keypad initiated IR commands derived from the internal IR library High or low IR power output is set by means of the HI LO switch Set it to the LO setting when driving standard low power emitters i e Proficient IR single flasher Set it to the HI position when driving a high power emitter i e a blaster for teaching IR commands into learning remotes Caution The HI position will damage or destroy low power emitters COMMON STATUS OUT PORT This 3 5mm mini phone jack will go high 12V DC when any zone is turned ON and will go LOW under 1V D
16. o the original retail purchaser only that this product will be free from defects in materials and workmanship for a period of two years provided the Crosstalk Between Sources gt 65dB 10kHz speaker was purchased from a Proficient Audio Systems Authorized Dealer gt 95dB VC 20dB IEC A below FCW S N Ratio re rated output source inputs shorted Defective products must be shipped prepaid and insured together with proof of purchase to the Proficient Audio Systems Authorized Dealer from whom they were purchased or to Proficient Audio Systems at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk of loss or damage in transit Bass Control Range 10dB 100Hz is to be borne by the purchaser Treble Control Range 10dB 10kHz If upon examination at the Factory or Proficient Audio Systems Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this warranty period Proficient Audio Systems or the Proficient Audio Systems Authorized Dealer Control Sections will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effectively Proficient Audio Systems at its sole option
17. of up to 1000 L amp R SPEAKERS TERMINALS These 4 circuit plugable screw down terminals accept wire sizes from 14 to 28 AWG They allow quick connection of the internal amplifiers to stereo pairs of speakers in the various zone rooms IR OUT This 3 5mm mini jack one for each zone provides dedicated Zone IR output initiated from the respective zone inputs They may control specific zone components when you want to prevent the control of it from the other zones VC NVC SWITCH The audio output from the PRE OUT jacks can either be controlled by the internal volume control of the M4 VC position or be a fixed line level output in the no volume control NVC position In either case the tone control remains available for room EQ settings IEC TYPE AC Mains receptacle and fuse mates with included AC power cord Also houses the rear panel replaceable AC mains fuse T5AL 250V for 120V and T2 5AL 250V for 230V 240V M4 AUDIO CONTROLLER WITH KEYPAD SYSTEM The Proficient M4 System consists of four subsystems First the keypads themselves can be configured in many key icon arrangements and placed in a one two or three gang set up to meet virtually any client requirement They are connected via convenient CAT5 cable with home run lengths of up to 1000 305m or longer if heavier gauge wire is used to the centrally located M4 Multi Zone Audio Amplifier Controller located near the controlled equipment The M4 contains th
18. or the M4 When the system is off all buttons have a background green color When a source button is pressed it turns to a low level red color to show that it is the active source and the system is on 2 Keypad Expansion Terminal This 16 pin header terminal is used to inter connect the optional numeric and function keypad modules for expansion as needed A 3 connector ribbon cable is packed with each module for making these connections 3 Address Switch A unique hex address must be set for each master keypad when connected on a common bus within a single zone Unique addresses are not required zone to zone It provides up to 16 addresses 0 to F 4 Snap Tabs These tabs hold the decorator style insert panel to the metal mounting plate and are easily released for custom changing of the buttons 5 Mounting Plate Standard plate allows the keypad module to be attached to standard in wall PNK Numeric Keypad Not included with M4 Cc y Rear View Rear View PFK Function Keypad Not included with M4 J Boxes using the two screws provided Allows attachment of standard decorator type cover plates also screwless snap on plates 6 IR Receiver Lens Version PMKIR includes Proficient s exclusive ANS IR receiver built in It allows the use of a handheld remote for control of system components 7 Connection Terminals for CAT5 home run termination Relay and Relay for future use 12V Powers
19. s ura ura ura ura would be as follows le R PRE OUT TNR1 Audio Source 1 TNR2 Audio Source 2 z 7 1 Pull all wiring for the keypads speakers etc from As P gatos aoa oe eae ats up3 urs ur3 urs R232 FIRMWARE COMMON COMMON PROFICIENT Oo NVC the various zone rooms home runs to a central udio Source 5 Audio Source 6 In addition ol 0 AM equipment area a Mute Off command is programmed under each an ep aS GB ee 2 oe pone pace m NTR OFF ON moo ae Dee 4 BEUT e P f Riverside CA USA 2 nd m n r i Source key PrN am am PrN oon Oo oo l 007 a 4 The six Function keys are programmed as follows py b4 lt Y L z L R L R R L R M4 the amplifiers to speakers in rooms etc KEYPAD L i a BASS 1st press changes Vol UP Down to Bass Up lt Pad 0 0 O O 0 0 O O ZONE 4 FE nae a eT ee Loop 3 Make sure all system components function first cans RS485 Control IR Signal OSE TANE i a SRE lias with their own remote controls before configuring TREB 1st press changes Vol Up Down to Treble Up and Keypad Rower e eo B ne eo B w the keypads Down 2nd press Treble Flat 20V 60Hz 18A 7 ON 2 A press Meble at To To To To rrr eA y N FUSE TSAL 280V 4 Flasher placement Locate each source n Volume Up command Also serves as Bass or ao irae a acl A z component s IR Sensor window Place emitters on Treble Up after first pressing BASS or TREB keys EPD ZONET EPD ZONE 2 ZONES i a each of the sour
20. ster Keypad Included with M4 Double Gang Set Up 1 PMKIR Source Function Buttons Six of this set of eight buttons are programmed as source select for the M4 When the system is off all buttons have a background green color When a source button is pressed it turns to a low level red color to show that it is the active source and the system is on 2 Keypad Expansion Terminal This 16 pin header terminal is used to inter connect the optional numeric and function keypad modules for expansion as needed A 3 connector ribbon cable is packed with each module for making these connections 3 Address Switch A unique hex address must be set for each master keypad when connected on a common bus within a single zone Unique addresses are not required zone to zone It provides up to 16 addresses 0 to F 4 Snap Tabs These tabs hold the decorator style insert panel to the metal mounting plate and are easily released for custom changing of the buttons 5 Mounting Plate Standard plate allows the keypad module to be attached to standard in wall KORO PNK optional lt 1 77 gt OO 000 OOO Numeric Keypad KEYPAD EXPANSION ap Ww Z y PNK Numeric Keypa E Not included with M4 J Boxes using the two screws provided Allows attachment of standard decorator type cover plates also screw less snap on plates 6 IR Receiver Lens Version PM
21. the keypad including the internal IR receiver on model PMKIR Includes reverse voltage protection Data Sends IR control signals for control of system components GND Return for power IR signal and data 485 A 485 B Balanced bi directional system communications data 8 Function Buttons These lower four buttons can be programmed for any function except source select 9 Numeric and Function Buttons Require programming via Proficient Editor All buttons glow background green and can be configured to go off after a set time or stay on via Proficient Editor SYSTEM CONNECTIONS AND CONFIGURATION Factory Default System As mentioned earlier the M4 comes with a set of four pre configured PMKIR keypads one for each zone In addition the M4 is pre programmed at the factory Whole House Party Mode 5 All zones are set for Whole House Party Mode capability Whole House Party Mode Forces all zones to the same source and allows volume and mute TUNER 1 TUNER 2 A TYPICAL M4 KEYPAD CONTROLLED SYSTEM CD PLAYER 2 MP3 PLAYER A TYPICAL M4 INSTALLATION Perhaps the best way to become familiar with the M4 keypad system is to show its application in a typical installation Figure 7 shows the four PMKIR keypads included controlling the M4 and related O oooo EIIN To engage Whole House Party Mode press and IR Flasher source components in a four zone application with a default project so that the en
22. tire system will functions to operate all zones in unison function right out of the box The installer can use this default as a base on which to build customized NOTE The system in Figure 7 is given to illustrate the basics on how to configure and program i IR Out from S Jod IR Out f niid bead dal pee projects The default project has the following hold nate Source sae oe two IR Out momsoutee 4 ut from Source 2 Out from Source 3 gt IR Out from Source 4 IR Out from Source 5 IR Out from Source 6 gt a system not to show all aspects of such an functionality Refer to Figures 3 amp 7 ane repli AE PA S cargo installation For instance for simplicity the speakers f l ToS 3 i A ToS 6 in each zone are not shown in Figure 7 even though 1 Six Source keys TNR1 TNR2 SAT CD CD2 MP3 apa bane 3 yas sieht 3 inpats such components would be required for a complete 2 Six Function keys BASS TREB MUTE PWR VOL UP i L R L R L R L R L R working system eon Zone 1 Zone 2 Zone 3 Zone 4 ie ae NOTE Maximum recommended lead length for the 3 The six Source keys are set as Zone ON keys and PMKIR PMKIR PMKIR PMKIR L R From Doorbell Trigger keypads with CATS cable is 1000 305m Keypad Keypad Keypad Keypad are programmed to select the M4 rear panel Audio m N The recommended steps to install such a system Source inputs as follow
Download Pdf Manuals
Related Search