Polaroid TTM-2101L User's Manual
Contents
1. OR VHF UHF or Cable 300 ohm twin lead cable not supplied Antenna adapter not supplied RF Input back of TV unit U V mixer not supplied Notes 1 It is recommended that a 75 ohm coaxial cable be used in order to eliminate interference and noise which may occur due to nearby radio transmissions 2 The antenna cable should not be tied together with other wiring 3 Set up a lightning rod and check it regularly when an outdoor antenna is used Installing the Remote Control Batteries 6 1 Remove the battery compartment lid 2 Insert two AAA batteries included Make sure the positive and negative polarities are correctly aligned 3 Reattach the battery lid Notes 1 Alkaline batteries are recommended for longer life 2 Always replace both batteries at the same time 3 Do not expose batteries to fire or break them open 4 To avoid battery leakage remove batteries from the remote control when it is not being used for a long period of time Instruction Manual INSTALLATION continued Connecting A V Equipment The following are diagrams showing basic instructions for attaching external equipment like a VCR or DVD player to your TV set Please refer to operation manuals of external audio video equipment that will be connected to your set for additional instructions PLEASE TURN OFF ALL POWER BEFORE CONNECTING DEVICES TOGETHER Connect VCR s RF OUT terminal to the RF IN jack lo2. guidelines for proper grounding and in particular specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical Customer Record You will find the model number and chassis number of your TV on the back of your TV set Record these numbers in the spaces provided below Refer to them whenever you call customer service or your dealer regarding this product Model Number Chassis Number PACKING LIST Color TV Receiver Remote Control Operation Manual AAA Alkaline Batteries Please read this manual carefully before operation 1 Instruction Manual IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 1
3. middle of the grid Pressing the MENU key with one of TV Y these individual ratings highlighted will block only programs TV Y7 U that feature that particular aspect See the TV rating diagram TV G at right for an example TV ratings are defined in the charts TV PG U below TV 14 B TV MA Age Based Rating Defined as Defined as All Children Fantasy Violence Directed to Older Children over 7 Sexual Dialogue General Audience Adult Language Parental Guidance Suggested Sexual Situations Parents Strongly Cautioned Violence Mature Audience Only MPAA Rating MPAA Rating Press the right arrow key while in the TV Rating grid to a Rating access this grid Use the up or down arrow key to navigate PG between the MPAA ratings Pressing the MENU key with a PG 13 rating highlighted will block that particular rating from being R shown on this TV A B will show in red next to the blocked NC 17 rating Please note that blocking a lower rating for example X PG will block all higher ratings PG 13 R NC 17 X Age Based Rang Pass Code Menu This menu allows you to change the access code for the Parental Guide functions of the TV set Press the MENU key Pass Code Menu when Pass Code Control is highlighted This will turn on or off the Pass Code function With the Pass Code function ON Pass Code Control you can also change the Pass Code Use the down arrow Pass Code 6688 key to highlight Pass Code then enter the new Pas
4. 0 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Warning This TV should only be serviced by an authorized and properly trained technician Opening the cover or other attempts by the user to service this TV may result in serious injury or death from electrical shock and may increase the risk of fire Oe aN FCC Warning Class B Computing Device Information to User This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equip
5. 21 Pure Flat Tube Stereo Television TTM 2101L 20060630 Instruction Manual WARNING To reduce the risk of fire or electric shock do not expose this product to rain or moisture The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel CAUTION Caution To reduce the risk of electric shock do not RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates dangerous voltage This symbol indicates important inside the product that presents a risk of ie instructions accompanying the product electric shock or personal injury Caution To prevent electric shock match wide blade of plug to wide slot fully insert Refer to the identification rating label located on the back panel of your product for its proper operating voltage Caution Using video games or any external accessory with fixed images for extended periods of time can cause them to be permanently imprinted on the picture tube or projection TV picture tubes ALSO some network program logos phone numbers etc may cause similar damage This damage is not covered by your warranty Cable TV Installer This reminder is provided to call your attention to Article 820 40 of the National Electrical Code Section 54 of the Canadian Electrical Code Part 1 which provides
6. Off time PICTURE Selects the various Picture Modes I 4 CC Activates Closed Captioning STANDBY Turns on off the TV o Em KEYPAD Used to select channels by number CH Used to change the current channel VOL Used to adjust the volume level MENU Accesses the TV menus ENTER Accesses the sub menu RECALL Returns to the last channel viewed MUTE Mutes or restores the TV volume TIMER Accesses the Timer menu OD Instruction Manual INSTALLATION Please read the safety instructions in this manual completely before installation Install your TV in an area where direct sunlight will not fall upon the screen Soft indirect light is best for television viewing Allow enough space at least 4 in between the TV and any walls or enclosures for proper ventilation Optimum television viewing distance is 3 5 times the screen s size Auto Degaussing Color television can be easily affected by magnetism which shows as color distortion on the screen If your TV is affected by nearby magnetic components or appliances turn it off for a few minutes The built in auto degaussing circuit will eliminate the magnetic interference Auto off when no signal received The TV set will automatically enter into Standby mode when the following conditions are met 1 TV is in antenna mode 2 Current channel has no signal 3 No key is pressed within 15 minutes Connecting the Antenna 75 ohm coaxial cable not supplied
7. cated on the rear panel of the TV Coaxial Cable 65 RF IN VCR UL Input from Device to TV AUDIO VIDEO OUT The side terminals may be easier to use with a camcorder The connections are identical DVD Player With S VIDEO Terminal VIDEO AUDIO VIDEO Yellow R LIMONO 0 Camcorder AUDI White VCR Output from TV to Device AUDIO VIDEO IN AV OUT VCR Q Instruction Manual FUNCTIONS amp FEATURES Turn On Off 1 Turn On Plug in the power cord and the TV should enter into Standby mode Pressing STANDBY key will turn on the TV and its power indicator light 2 Standby While the TV is on press the STANDBY key will put the TV in Standby or off mode The power indicator light on the TV set will turn off Basic Functions Changing the Channel While in Tuner mode press the CH keys to change the channel or use the numeric keypad to enter a new channel Adjusting the Volume To adjust the volume press the VOL keys Also you may press the FUNCTION F key along with the VOL keys to adjust the volume in increments or decrements of 4 Muting the Volume To mute the volume press the MUTE key To restore the volume press MUTE again or press the VOL key Function Selection Menus To change the setting of any function press the MENU key to bring up the main menu Press the up or down arrow key to highlight the desire sub menu and press the left or right arrow key o
8. feature prevents unauthorized viewing of the TV To activate press and hold the F key and then press MUTE You should see a key symbol appear on the screen This will lock out all remote functions except for Standby To unlock the TV press and hold the F key and press MUTE This will unlock the TV Please note that the only way to activate or deactivate the Child Lock feature is via remote control please insure that it is stored securely SLEEP Press the SLEEP key repeatedly to switch the TV to one of the following modes gt 15 gt 30 gt 45 60 90 120 150 180 Unit Minute The TV will automatically enter the Standby mode when the preset Sleep time is up The TV will display a message one minute before the Sleep timer runs out 0 9 Press the 0 9 keys to enter channel numbers directly 2 69 in the Air mode or 1 125 in the Cable mode Press the corresponding Number key s to enter a channel number from high digit to low digit Each digit should be entered at 3 seconds time interval
9. for the TV On Off Timer feature that allows the user to set a time to turn on off the TV Parental Control feature that allow parents to block out selected type of programming RF IN Jack standard coaxial antenna jack S Video Input input designed for greater clearity and sharpness also known as S VHS Screen Size the diagonal size of the TV screen Selectable Picture Modes preset standards for TV display User Normal Movie and Sports Trilingual On Screen Display OSD TV s on screen display can be either English French or Spanish FEATURE gt 181 Channel Tuner V Input Rear V Input Front V Input Side V Output Rear hannel Recall losed Caption ull Feature Remote gt gt arental Control RF IN Jack Video Input creen Size icture Modes rilingual OSD S lt 0 A Q D Instruction Manual Front and Rear Unit Profiles MENU VOL CH Y SELECT MENU CHANNEL DOWN UP VOLUME DOWN UP Front panel Side panel Rear panel POWER INDICATOR MAIN POWER SWITCH INFRARED SENSOR AV IN on the side panel AUDIO VIDEO L MONO S VIDEO QO QO Instruction Manual Remote Control Features FUNCTION Used for volume control and child lock VIDEO Cycles through the Video TV modes DISPLAY Brings up the TV Video display ARROWS Used to navigate the TV menus SCAN scans all active channels SLEEP Used to set the Sleep
10. ment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment receives interference while off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and TV 3 Connect the equipment into an outlet on a circuit different from that to which the TV is connected 4 Consult the dealer or an experienced radio TV technician for help and for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the US Government Printing Office Washington D C 20402 Stock No 004 000 00345 4 FCC Warning The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment NOTE In order for an installation of the product to maintain compliance with the limits for a Class B Device shielded cables must be used TABLE OF CONTENTS INTRODUCTION Safety Instructions Specifications Feature Descriptions Front and Rear Unit Profiles Remote Control Fea
11. ner to an Air antenna or a Cable antenna Please use Air mode when using an over the air antenna use Cable mode for a cable hookup Use the left or right arrow key to select between the two options Auto Program This feature will setup the Active channel list for the user The list will include only the channels with a signal detected Press the right arrow key to begin and the left arrow key to stop the process Timer Menu Press the TIMER key on the remote control to access this menu Time Timer This feature allows you to set the clock on the TV Time On Time On Time This feature allows you to preset a time when the TV set will turn on On Channel On Channel Sd g This feature allows you to preset the channel on display when the Timer On Time is activated Off Time This feature allows you to preset a time when the TV set will turn off Timer Timer can be set to Once or Always System Menu Language This feature allows you to pick a language used for the on screen display OSD Use the left or right arrow key to select the language of your choice English Eng French Fra or Spanish Esp Blue Back System This feature gives you the option to display a blue background on the TV screen when there is no signal present Use the left or right arrow key to Language Fra Esp Blue Back On toggle between on and off CCD Text Orr CCD Text Parental Guide On This is a feature that allows your TV set to display on
12. r ENTER key to access While in the sub menu use the up or down arrow key to select the item and the left or right arrow to adjust the setting Press the MENU key to return to the main menu and exit While in the setup menu CH and VOL key on the front panel will function as the down up left right arrow keys on the remote control Features This menu allows you to adjust the various picture settings Use the Picture up or down arrow key to move between the various settings and the left or right arrow key to adjust them Tint Tint 31 more purplish to 31 more greenish aa Brightness 0 dimmest to 63 brightest Color Contrast 0 minimum contrast to 63 maximum contrast Sh Color 0 minimum color to 63 maximum color arpness oo 2 32 Sharpness 0 minimum sharpness to 63 maximum sharpness Instruction Manual FUNCTIONS amp FEATURES continued Note This menu is only accessible while the TV is in Tuner mode Channel This feature allows you to change the channel displaying on ane screen Use the left or right arrow key or the numeric keypad to change the Channel 2 channel Add Erase Add Add Erase This feature allows you to add or remove the channel Antenna Air currently on display from the active channel list This is the list of Auto Program channel available by pressing the CH keys Use the left or right arrow key to add or erase lt Stop Start D gt Antenna This feature sets the TV tu
13. s Code using the numeric keypad Enter Pass Code Note The factory pre set password is 6688 The initial password will be replaced when the new one is used Please contact the service centre in case you forget the password 11 Instruction Manual FUNCTIONS amp FEATURES continued Useful Remote Control Features DISPLAY This key allows you to display the current information of the TV screen on the upper right hand corner of the screen channel antenna mode time video etc TIMER This key allows you to directly access the Timer menu For an explanation of this menus features please see page 10 SCAN Press the SCAN key twice and the TV will begin to scan through all active channels To stop the Scan pressing any key can interrupt scanning Please note that Scan will only work in Antenna mode PICTURE Your TV has factory preset picture modes that allow you to optimize your TV viewing To activate these picture modes press this key and you can choose among User Normal Movie and Sports RECALL This key will allow you to return to the last channel you were viewing Pressing it again will return you to the channel you just left CC Pressing the CC key will activate the currently selected Closed Captions or Text under the System Menu Pressing it again will turn off the Closed Captions or Text VIDEO This key allows you to toggle between antenna and different video modes Child Lock The Child Lock
14. screen the dialogue narration and sound effect of a TV program It also allows MPAA X TV MA you to display teletext signal Text and caption will be displayed at either the top or the bottom of the screen There is nine different setting for closed caption You can set it to one of the 4 Closed Caption settings CC1 4 one of the 4 Text settings T1 4 or set this feature to off CCD Text off Notes A Closed Caption signal may not be displayed under the following conditions When there is no Closed Caption Text signal to decode When the signal is weak or altered due to interference or poor reception When viewing a dubbed video tape 10 FUNCTIONS amp FEATURES continued system Menu continued System Parental Guide Bas ue ee Language Eng Fra Esp This feature allows parents to block certain programs from being 0 p Blue Back viewed based on the programs rating In order to access this CCD Text menu you must first enter a pass code The factory default is 6688 t Parental Guide On Enter the pass code while the Parental Guide is highlighted Now with Parental Guide set as On press the right arrow key to access MPAA X TV MA giie TV Rating Using the up or down arrow key to navigate between the ratings press the MENU key to block out a particular rating TV Rating completely Or if you wish press the down arrow key to highlight an individual rating anywhere a U is displayed in Rating FV D LS V the
15. tures INSTALLATION Connecting the Antenna Installing the Remote Control Batteries Connecting A V Equipment Input from Device to TV Output from TV to Device FUNCTIONS amp FEATURES Turn On Off Basic Functions Function Selection Menus Picture Menu Tuner Menu Timer Menu System Menu Useful Remote Control Features TROUBLESHOOTING GUIDE SPECIFICATIONS MODEL TTM 2101L Television System NTSC M Channel Coverage VHF 2 13 UHF 14 69 Mid Band A 8 A 1 A l Cable TV Coverage Super Band J W Hyper Band AA ZZ AAA BBB 65 94 100 125 Antenna Input 75 ohm unbalanced 406 x 305 mm 1 Power Source 120V 60Hz Unit Weight 50 6 Ibs 23 kg Unit Dimensions 23 03 22 05 x 16 03 in 585 x 560 458 mm Packaged Dimensions 25 09 x 21 06 21 65 in 645 x 535 550 mm Power Consumption 90W Audio Output 2W 2W Instruction Manual Feature Descriptions 181 Channel Tuner total number of channels the TV can receive 2 69 in Air mode or 1 125 in Cable mode AV Input Rear input designed for use with A V devices such as a VCR or DVD player AV Input Side input designed for infrequent use such as with a camcorder or video game unit AV Output Rear output signals from TV to devices such as VCR s Channel Recall instant return to the last channel viewed Closed Caption Display feature that displays the closed caption or text of a TV broadcast Remote Control A wireless remote control unit
Download Pdf Manuals
Related Search