Planet Technology WAP-6200 User's Manual
Contents
1. 802 11g Wireless LAN Outdoor CPE AP WAP 6200 Quick Installation Guide Table of Contents Package e LEE Hardware Installation sene one geed gg e eege wie ay zieken beans darts nine read oan karena Web ee UC el EE lege le le e Designed with the most innovative 802 11b 802 11g technology WAP 6200 provides 54Mbps high data rate for outdoor environment There are five operating modes supported in WAP 6200 AP Client WDS AP WDS Repeater AP Wireless Client Repeater and Bridge The multiple operation modes selection and built in 14dBi flat panel antenna and default 200mW output power make WAP 6200 a suitable CPE solution for widely open space applications such as WISPs campuses and airports Except for 64 128 bit WEP encryption WAP 6200 integrates WPA WPA2 and 802 1x encryption to secure the information of your wireless LAN Package Content e WAP 6200 x 1 e PoE injector x 1 e Power Cord x 1 e Mounting Kit x 1 e CD ROM x 1 e Quick Installation Guide x 1 If any of the above items are missing or damaged contact your local dealer for support Hardware Installation POLE 1 1 5 HOSE CLAMP 2 Before you proceed with the installation it is necessary that you have enough information about WAP 6200 1 Locate an optimum location and use the provided Mounting kit to tie the WAP 6200 to a pole For secured reason while install the CPE AP please be aware for the electr2. TOUCH THAT PERSON OR YOU MAY BE ELECTROCUTED e Use a non conductive dry board stick or rope to push or drag them so they no longer are in contact with electrical power e Once they are no longer contacting electrical power administer CPR if you are certified and make sure that emergency medical aid has been requested Web Configuration WAP 6200 provides a user friendly interface for users to configure via web browser Please follow the below steps to configure WAP 6200 basic settings 1 It will take about 55 seconds to complete the boot up sequence after power on from PoE 2 Open your web browser and type WAP 6200 default IP address http 192 168 1 254 into the Address Field of you web browser Before configuration please make sure your PC s IP address is under the same IP range with WAP 6200 such as 192 168 1 x 3 After enter the IP address and press Enter key you can see the login web page without any username password 802 11g WLAN Outdoor AP Broadband Router Status This page shows the current status and some basic settings of the device System Uptime Oday Oh Or 575 Firmware Version VER Mode AP Band 24 GHz B G SSID Mat AN Channel Number 11 Encryption Disabled BSSID 00 304 69 5b 1d Associated Clients 0 Attain IP Protocol Fixed IP IP Address 192 168 1 254 Subnet Mask 255 255 255 0 Default Gateway 192 168 1254 DHCP Server Enabled MAC Address 00 30 4f69 5b 1d Attain IP Protocol G
3. e total length of the mast antenna combination This will ensure that the mast will not contact power if it falls either during installation or later TO AVOID FALLING USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND Select equipment locations that will allow safe simple equipment installation e Don t work alone A friend or co worker can save your life if an accident happens e Use approved non conducting lasers and other safety equipment Make sure all equipment is in good repair e If a tower or mast begins falling don t attempt to catch it Stand back and let it fall e If anything such as a wire or mast does come in contact with a power line DON T TOUCH IT OR ATTEMPT TO MOVE IT Instead save your life by calling the power company e Don t attempt to erect antennas or towers on windy days MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS This will help prevent fire damage or human injury in case of lightning static build up or short circuit within equipment connected to the antenna e The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods using 1 OAWG ground wire and corrosion resistant connectors e Refer to the National Electrical Code for grounding details IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER AND CANNOT MOVE e DON T
4. etting IP from DHCP server Further Configuration For more settings of WAP 6200 please refer to the user s manual in the CD If you have any difficulty on resolving the problem while installing or using the device please feel free to contact your local dealer or PLANET Technical Support
5. he PoE Injector and plug it into an AC outlet to power on the WAP 6200 87654321 em 87654321 8 J1 J2 J1 Pins J2 Pins 1 Data Pair 1 4 gt 1 Data Pair 1 2 Data Pair 1 lt 2 Data Pair 1 3 Data Pair 2 4 gt 3 Data Pair 2 4 VDC 4 No Connection 5 VDC 5 No Connection 6 Data Pair 2 lt 6 Data Pair 2 7 VDC 7 No Connection 8 VDC 8 No Connection 1 ONLY use the power adapter supplied with the WAP 6200 Otherwise the product may be damaged 2 Strongly suggest using SFTP cable whether the cable exposed outdoor for waterproof and avoiding thunder stroke 5 e A N OUTDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS LIVES MAY BE AT RISK Carefully observe these instructions and any special instructions that are included with the equipment you are installing CONTACTING POWER LINES CAN BE LETHAL Make sure no power lines are anywhere where possible contact can be made Antennas masts e towers guy wires or cables may lean or fall and contact these limes People may be injured or killed if they are touching or holding any part of equipment when it contacts electric lines Make sure there is NO possibility that equipment or personnel can come in contact directly or indirectly with power lines Assume all overhead lines are power lines The horizontal distance from a tower mast or antenna to the nearest power line should be at least twice th
6. ic wires around and tighten the pole Without tighten the CPE AP the pole and the installed site is with electric wire around there could be danger of being hurt by falling or lethal injury 2 Strongly suggest using SFTP cable PLANET offers 25 meter SFTP cable please contact with local dealer for more information for waterproof and avoiding thunder stroke connect the RJ45 cable connector of the WAP 6200 to the P DATA OUT port of PoE Injector Strongly suggest using SFTP cable for better protection of the data wire 25 meter SFTP cable also available by order the part no is WL SFTP 25 Please contact with local dealer for more information 3 Be noticed there are 2 ways for RJ45 cable connector avoiding water or thunder stoke a Stick and bind with rubber mastic tape on RJ45 cable connector after connecting cable to P DATA OUT port of PoE Injector b After connecting cable to P DATA OUT port of PoE Injector open the Back Cover and put the RJ45 cable connector inside of Back Cover then plug the Back Cover to CPE Set for preventing water 4 Using Category 3 or higher UTP or STP cable connect the DATA IN port of PoE Injector to a 10Mbps or 10 100Mbps Ethernet hub or switch and connect the PC on the same LAN for management To avoid thunder strike consider to install ELA 100 thunder arrester toward the CPE AP and the PoE injector 5 Connect the power cord to t
Download Pdf Manuals
Related Search