Planet Technology 802.11nWireless User's Manual
Contents
1. Data Transfer Rate IEEE 802 11b 11 5 5 2 1M IEEE 802 11g 54 48 36 24 18 12 9 6 IEEE 802 11n 300 270 243 240 216 180 162 120 108Mbps in 40Mhz mode 145 130 117 104 78Mbps in 20Mhz mode Operating Mode Infrastructure Mode Ad Hoc Mode Security WEP 64 128bit WPA WPA2 802 11b DSSS CCK QPSK BPSK RF Modulation 802 119 OFDM 802 11n 64QAM 16QAM QPSK BPSK Output Power 11b mode 16 18dBm 11g mode 14 16dBm 11n mode 11 13dBm 2 412 2 462GHz FCC Canada 11 Channels Channels 2 412 2 4835GHz Japan TELEC 14 Channels 2 412 2 472GHz Euro ETSI 13 Channels Management Built in utility or Windows XP Zero Configuration utility Operating systems Windows 2000 XP Vista Environmental amp Mechanical Characteristics Temperature Operating 0 C 55 C Storage 20 C 70 C Operating Humidity Operating 0 85 Storage 0 95 Non Condensing Dimensions 83 x 27 x10 mm Lx WxH Weight 14g Certifications FCC CE 1 3 Package Contents Before you begin the installation please check the items of your package The package should include the following items 1 x WNL U552 1 x Driver and User s manual CD 1 x Quick Installation Guide If any of the above items is missing contact your supplier as soon as possible Chapter 2 Installation Procedure Utility Installation 1 3 4 5 Insert the bundled CD into the CD ROM drive2. PLANET Networking amp Communication 802 11n Wireless USB Adapter WNL U552 User s Manual Version 1 00 Date August 2007 Copyright Copyright 2007 by PLANET Technology Corp All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of PLANET PLANET makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not PLANET its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes All brand and product names mentioned in this manual are trademarks and or registered trademarks of their respective holders Federal Communication Commission Interference Statement This equipment has been
3. Minimum packet size required for an RTS Request To Send For packets smaller than this threshold an RTS is not sent and the packet is transmitted directly to the wireless network Select a setting within a range of 0 to 2347 bytes Minor change is recommended The value defines the maximum size of packets any packet size larger than the value will be fragmented If you have decreased this value and experience high packet error rates you can increase it again but it will likely decrease overall network performance Select a setting within a range of 256 to 2346 bytes Minor change is recommended 12 Channel This setting is only available for Ad Hoc mode Select the number of the radio channel used for the networking The channel setting should be the same with the network you are connecting to 3 2 2 Add Profile Authentication and Security Add Profile Configuration Authentication and Security Authentication Type Use 802 1 Encryption None WPA Preshared Key Wep Key C Show Password Parameter Description Authentication Type This setting has to be consistent with the wireless networks that the card intends to connect Open No authentication is needed among the wireless network Shared Only wireless devices using a shared key WEP Key identified are allowed to connecting each other Authentication Type LEAP LEAP is a pre EAP Cisco proprietary protocol with many of the fea
4. Receive Statistics Frames Received Successfully Frames Received With CRC Error Frames Dropped Due To Out of Resource Duplicate Frames Received Reset Counter 20 3 5 Advance This option enables you to configure more advanced settings for example wireless mode protection mode and etc M Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About Wireless mode 802 11 B G N mix lt Select Your Country Region Code wireless Protection ato w 11B G 0 CH1 M CI Tx BURST C Show Authentication Status Dialog C Enable TCP window Size C Enable CCX Cisco Compatible extensions C Fast Roaming at BG _tum ott RF Parameter Description Wireless Mode Select Your Country Region Code 802 11 B G N mix If you have a mix of 802 11b 802 119 and 802 11n wireless stations in your network It is to maximize wireless compatibility with wireless access points and other wireless devices it is recommended to setting the card to this mode This mode is also the default setting 802 11 B G mix If you have a mix of 802 11b and 802 119 wireless stations in your network it is recommended to setting the card to this mode 802 11 B only This card can be compatible with both 802 11g and 802 11b wireless stations If there are only 802 11b wireless stations in the network you can set the card to this mode The avail
5. for the user s identity to the device EAP or the Extensible Authentication Protocol is an authentication protocol that runs before network layer protocols transmit data over the link In turn the device responds with its identity and the AP relays this identity to an authentication server which is typically an external RADIUS server 15 An example for MD5 Authentication IEEE 802 1x RADIUS RADIUS Access Client Client a Server 4 Xy ue Y oo xXx 7 Se yn S Q EN Access Point FS till hg A L ee Windows 2000 IAS Internet Authentication Service 1 Client requests to login the network 2 Login with username password 802 1x Setting Certification CA Server Authentication Type a343 v Identity i o C Use Client certificate Tunneled Authentication Protocol 3 Send username password to RADIUS server 4 Approve or deny user login to the LAN Session Resumption Disabled v Domain Name EAP MSCHAP v2 Identity Password Parameter Description Authentication Type The EAP authentication protocols this card has supported are included as follows This setting has to be consistent with the wireless APs or Routers that the card intends to connect PEAP amp TTLS PEAP and TTLS are similar and easier than TLS in that they specify a sta
6. network card to his her access point s list Q The network is slow having problem when transferring large files Ans 1 Move closer to the place where access point is located 34 2 Enable Wireless Protection in Advanced tab 3 Try a lower TX Rate in Advanced tab 4 Disable Tx Burst in Advanced tab 5 Enable WMM in QoS tab if you need to use multimedia telephony related applications 6 Disable WMM Power Save Enable in QoS tab 7 There could be too much people using the same radio channel Ask the owner of the access point to change the channel number 4 2 Glossary 1 What is the IEEE 802 11g standard 802 11g is the new IEEE standard for high speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2 4 GHz band 802 11g is quickly becoming the next mainstream wireless LAN technology for the home office and public networks 802 11g defines the use of the same OFDM modulation technique specified in IEEE 802 11a for the 5 GHz frequency band and applies it in the same 2 4 GHz frequency band as IEEE 802 11b The 802 11g standard requires backward compatibility with 802 11b The standard specifically calls for A A new physical layer for the 802 11 Medium Access Control MAC in the 2 4 GHz frequency band known as the extended rate PHY ERP The ERP adds OFDM as a mandatory new coding scheme for 6 12 and 24 Mbps mandatory speeds and
7. the WNL U552 supports both 64 128 bit WEP Wired Equivalent Privacy and WPA WPA2 Wi Fi Protected Access for securing wireless network connections The driver and utility support most popular operating systems Windows 2000 XP and Vista With advanced features and high performance capability the WNL U552 is an excellent choice for constructing a wide range of wireless solutions The power consumption of the card is also very low This card provides several levels of power saving modes allowing user customizes the way of saving the power from his her portable or handheld devices 1 1 Features 2 4GHz ISM band unlicensed operation Supports Wi Fi Protected Setup WPS e Compliant with IEEE 802 11b IEEE 802 119 IEEE 802 11n draft 2 0 e Compliant with USB 1 1 2 0 standard e Support 64 128 bit WEP and WAP WAP2 high level security mechanisms e Support Ad Hoc Infrastructure mode e Support WMM WiFi Multi Media function to meet the multi media data bandwidth requirement the connected AP and the application must support WMM as well e Support of Power Save mode High efficiency antenna expands the scope of your wireless network e QoS function Control the bandwidth required for different applications Support of most popular operating systems including Windows 2000 XP and Vista 1 2 Specifications Interface USB 1 1 2 0 Type A Standards Conformance Compliant with 802 11b 802 11g 802 11n draft 2 0
8. 18 36 48 and 54 Mbps optional speeds The ERP includes the modulation schemes found in 802 11b including CCK for 11 and 5 5 Mbps and Barker code modulation for 2 and 1 Mbps B A protection mechanism called RTS CTS that governs how 802 11g devices and 802 11b devices interoperate 2 What is the IEEE 802 11b standard The IEEE 802 11b Wireless LAN standard subcommittee which formulates the standard for the industry The objective is to enable wireless LAN hardware from different manufactures to communicate 3 What does IEEE 802 11 feature support The product supports the following IEEE 802 11 functions CSMA CA plus Acknowledge Protocol Multi Channel Roaming Automatic Rate Selection RTS CTS Feature Fragmentation Power Management 4 What is Ad hoc An Ad hoc integrated wireless LAN is a group of computers each has a Wireless LAN adapter Connected as an independent wireless LAN Ad hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation 35 5 What is Infrastructure An integrated wireless and wireless and wired LAN is called an Infrastructure configuration Infrastructure is applicable to enterprise scale for wireless access to central database or wireless application for mobile workers 6 Whatis BSS ID A specific Ad hoc LAN is called a Basic Service Set BSS Computers in a BSS must be configured with the same BSS ID 7 Whatis WEP WEP is Wired Equivalent Privacy a data pr
9. 3 6 QoS 24 3 7 WPS Config ration soe isee teses iia 26 3 7 1 WPS Setup PBC Push Button Configuration oconocccnococoncnannnonanonananncnnnos 27 ree WES Setup e LIN a daa s 29 BB ADO idas 32 Chapter Appendix gig scoters acs a a rE E EE E E G AE ECES 33 E 33 O a S 35 Chapter 1 Introduction For higher wireless transfer performance we are glad to introduce the PLANET 802 11n wireless USB adapter WNL U552 ltis a USB 2 0 wireless adapter that can operate in either Ad Hoc mode Point to Point Point to Multipoint without an Access Point or Infrastructure mode Point to Point Point to Multipoint with an Access Point 2 4GHz frequency band it s backward compatible with 802 11b and 802 11g for users to create a new wireless environment based on the existing wireless network With integrating the latest innovative 802 11n technology the maximum data rate of WNL U552 is up to 300Mbps which is almost six times of standard G Featuring smart antenna technology the 802 11n design helps combat distortion and interference so the Network Card can send its data streams with greater distances and be more reliable The WNL U552 supports the most convenient security Wi Fi Protected Setup WPS which is the way to build connection between wireless network clients and this wireless router This WNL U552 supports two types of WPS Push Button Configuration PBC and PIN code key Wireless adapter card pin number For WLAN security issues
10. Access Point All communication is done via the Access Point or Router Ad Hoc Select this mode if you want to connect to another wireless station in the Wireless LAN network without through an Access Point or Router If you want to lower the transmit power of the card for saving the power of the system you can select the lower percentages from the list The lower power will cause the lower signal strength and the coverage range When the card is set in Ad Hoc Peer to Peer Mode you can designate the wireless connection mode for the Ad Hoc network 802 11 B only This card can be compatible with both 802 11g and 802 11b wireless stations If there are only 802 11b wireless stations in the network you can set the card to this mode 802 11 B G mix If you have a mix of 802 11b and 802 119 wireless stations in your network it is recommended to setting the card to this mode This mode is also the default setting 802 11 G only This card can be compatible with both 802 11g and 802 11b wireless stations If there are only 802 119 wireless stations in the network you can set the card to this mode The preamble defines the length of the CRC block for communication among wireless devices This option is only active in the Ad Hoc network There are two modes including Auto and Long Preamble If Auto mode is selected the card will auto switch the preamble mode depending on the wireless devices the card is connecting to
11. Click Activate to connect to the selected profile When a profile is activated the card will be initially connected to the profile 10 3 2 1 Add Profile Configuration Add Profile Configuration Authentication and Security Profile Name PROF1 SSID v PSM CAM Constantly Awake Mode PSM Power Saving Mode Network Type Infrastructure v TX Power Auto My RTS Threshold 0 2347 C Fragment Thres hold 25 2346 Parameter Description Profile Name Define a recognizable profile name for you to identify the different networks SSID The SSID up to 32 printable ASCII characters is the unique name PSM Power Saving Mode identified in a WLAN The ID prevents the unintentional merging of two co located WLANs You may specify a SSID for the card and then only the device with the same SSID can interconnect to the card If you want to add the network nearby to the profile list pull down the menu all the networks will be listed for you to add one of them to the profile list The power saving function is only available when the network type is in Infrastructure CAM Constantly Awake Mode The card will always set in active mode PSM Power Saving Mode Enable the card in the power saving mode when it is idle 11 Network Type TX Power Ad Hoc Wireless Mode Preamble RTS Threshold Fragment Threshold Infrastructure This operation mode requires the presence of an 802 11
12. Encryption Disconnect pe Y WPS Probe IE MIPS status is not used 3 7 1 WPS Setup PBC Push Button Configuration 1 Push the WPS button on your wireless access point the button used to activate WPS standby mode or use other way to start WPS standby mode as the instruction given by your wireless access point s user manual 2 Before you start to establish the wireless connection by using WPS you can click Rescan button to search for WPS enabled access points near you to make sure the WPS function of your access point is activated 27 Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About SSID BSSID CID Authe Enciy Pin Code 26461915 SSID MAC Address Authentic Encryption Disconnect aaa A Ia pec MIWPSProbelE WPS statusis motused 000 All access points found will be displayed Please make sure the access point you wish to connect is displayed If not please click Rescan few more times You can also click Information button to see the detailed information about selected access point 5 Click PBC button now to start to establish wireless connection by WPS and please be patient This may require several seconds to one minute to complete When you see WPS status is connected successfully message means the connection b
13. Size The larger TCP Window the better performance When you want to fast roaming to the network nearby without intercepting the wireless connection especially the card is applied to the multimedia application or a voice call you can enable the parameter The card will fast roaming to the near network when the receive sensitivity signal strength is lower to the value you have set up If you want to turn off the radio of the card temporarily click this button To turn on the radio click this button again When your computer is being authenticated by wireless authentication server a dialog window with the process of authentication will appear This function is helpful to find out the problem when you can not be authenticated and you can provide this information to authentication server s administrator for debugging purpose Enable Cisco Compatible eXtensions CCX is a wireless feature developed by Cisco used to improve the wireless performance with CCX compatible wireless devices Check this box if you need to connect to CCX compatible wireless devices 22 Turn on CCKM Enable Radio Measurement Non Serving Channel Measurements Limit XXX 0 2000 During normal operation LEAP enabled client devices mutually authenticate with a new access point by performing a complete LEAP authentication including communication with the main RADIUS server When you configure your wireless LAN for fast re association however LEAP
14. WPA PSK key can be from 8 to 64 characters and can be letters or numbers This same key must be used on all of the wireless stations in the network WEP Key The WEP keys are used to encrypt data transmitted in the wireless network Key1 Key4 There are two types of key length 64 bit and 128 bit Select the default encryption key from Key 1 to Key 4 by selected the radio button Fill the text box by following the rules below 64 bit Input 10 digit Hex values in the A F a f and 0 9 range or 5 digit ASCII characters including a z and 0 9 as the encryption keys For example 0123456aef or test1 128 bit Input 26 digit Hex values in the A F a f and 0 9 range or 13 digit ASCII characters including a z and 0 9 as the encryption keys For example 01234567890123456789abcdef or administrator 3 2 2 1 802 1x Setting Certification The IEEE 802 1X specification describes a protocol that can be used for authenticating both clients and servers on a network The authentication algorithms and methods are those provided by the Extensible Authentication Protocol EAP a method of authentication that has been in use for a number of years on networks that provide Point to Point Protocol PPP support as many internet service providers and enterprises do When an AP acting as an authenticator detects a wireless station on the LAN it sends an EAP Request
15. be infrastruc 00 30 4F 26 E3 yA Infrastruc 00 30 4F 41 44 14 A infrastruc FIRSTINS 00 30 4F 86 35 y Infrastruc WRT 415 00 30 4F D3 70 4 infrastruc GLOBALHO 00 30 4F SE EB J infrastruc KINGBANK 00 30 4F CF DB infrastruc um gt Disconnected Rescan Add to Profile 3 8 About By choosing this option you can click the hyperlink to connect the PLANET website You can also obtain basic information about the WNL U552 such as the Driver Utility and EEPROM Version The MAC Address of the card is displayed in the screen as well Planet Wireless Utility ed Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About www planet com tw c Copyright 2007 Planet Technology Corp All rights reserved Utility Version eet Date 05 14 2007 Driver Version 1 0 2 0 Date 03 12 2007 EEPROM Version 1 1 Firmware Version 0 6 IP Address 0 0 0 0 Phy_Address 00 30 4F 28 60 4F Sub Mask 0 0 0 0 Default Gateway 30s Chapter 4 Appendix 4 1 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the adapter Q The PLANET WNL U552 does not work properly Ans 1 Right click on My Computer and select Properties Select the device manager and click on the Network Adapter You will find the Adapter if it is installed successfully If you see the yellow exclam
16. enabled client devices roam from one access point to another without involving the main server Using Cisco Centralized Key Management CCKM an access point configured to provide Wireless Domain Services WDS takes the place of the RADIUS server and authenticates the client so quickly that there is no perceptible delay in voice or other time sensitive applications When this parameter is enabled the Cisco AP can run the radio monitoring through the associated CCX compliant clients to continuously monitor the WLAN radio environment and discover any new APs that are transmitting beacons The Cisco AP can perform monitoring measurements through the CCX compliant clients on the non serving channels when this parameter is enabled milliseconds lt limits the channel measurement time The default value is 250 milliseconds Note This function is not support in the OS of Windows VISTA ee ae S Profile Link Status Site Survey Statistics About lt Disconnected Rescan Add to Profile airlive Ludy FIRSTINS WRT 415 GLOBALHO KINGBANK 00 30 4F 42 07 00 30 4F 26 E3 00 30 4F 41 44 14 00 30 4F 86 35 00 30 4F D3 70 z Unknown 00 30 4F SE EB A Unknown 00 30 4F CF DB Unknown ur p 23 3 6 QoS This wireless network card provides QoS Quality of Service function which can improve the performance of certain network applications like audio video streaming netwo
17. tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the Following two conditions 1 This device may no
18. testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation 5 The screen will show the rate of progress for the installation of WNL U552 as below Found New Hardware Wizard Please wait while the wizard installs the software ay PLANET WNL U552 t2860 sys To CAWINDOWS System32 DRIVERS CLIIIIIITITIITITITITIITIITIIITIIITIT 6 Please click Finish to complete the driver installation Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for PLANET WNL US52 Ba Click Finish to close the wizard 7 The WNL U552 utility will appear on the screen Please select the AP you would like to connect and press Connect button to link it Please click OK to continue m Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced DoS WPS Configuration About SSID BSSID SE Ge enc Authe Network RELAY 00 30 4F 09 BF 10 1 None Unknown Infrastruct E wtan ap 00 30 4F 03 3D 10 1 None Unknown Infrastruct 620 00 30 4F 28 60 10 3 TKIP WPA P Infrastru
19. Store and made available to the RADIUS server for certification When the authentication type is PEAP or TTLS select a protocol to be used to build the encrypted tunnel This is the protected user EAP Identity used for authentication The identity specified may contain up to 63 ASCII characters is case sensitive and takes the form of a Network Access Identifier consisting of lt name of the user gt O lt user s home realm gt The user s home realm is optional and indicates the routing domain The password used for authentication lt may contain up to 63 ASCII characters and is case sensitive 17 3 2 2 2 802 1x Setting CA Server 802 1x Setting Certification CA Server Certificate issuer Any Trusted CA v Allow intermidiate certificates Server name Server name must match exactly Domain name must end in specified name Cancel Help Parameter Description Use Certificate Chain Certificate Issuer Allow Intermediate Certificates Server Name Server name must match exactly When the EAP authentication type such as TLS TTLS or PEAP is selected and required a certification to tell the client what server credentials to accept from the authentication server in order to verify the server you have to enable this function Choose the server from the list to issue the certificate If Any Trusted CA is selected any CA included in the list provided by the Microsoft Cert
20. able channel differs from different countries For example USA FCC is channel 1 11 Europe ETSI is channel 1 13 The operating frequency channel will be restricted to the country user located before 29 2 Wireless Protection Tx BURST Enable TCP Window Size Fast Roaming at 70dBm Turn Off RF Button Show Authentication Status Dialog Enable CCX importing If you are in different country you have to adjust the channel setting to comply the regulation of the country If you have a mix of 802 11b and 802 11g wireless stations in the network it is recommended to enable the protection mechanism This mechanism can decrease the rate of data collision between 802 11b and 802 11g wireless stations When the protection mode is enabled the throughput of the card will be a little lower due to many of frame traffic should be transmitted Auto Based on the status of the network and automatically disable enable protection mode On Always enable the protection mode Off Always disable the protection mode Tx Burst enables the card to deliver the better throughput in the same period and environment This feature only takes effect when the connected AP also supports Tx Burst The TCP Window is the amount of data a sender can send on a particular connection before it gets an acknowledgment back from the receiver that it has gotten some of it This feature only takes effect when the connected AP also supports TCP Window
21. al of your wireless access point for instructions about how to do this 29 Planet Wireless Utility led Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About SSID BSSID CID Authe Enery Information Pin Code 26461915 SSID MAC Address Authentic Encryption Detail Connect Rotate Delete pac MIwPsProbelE fwpsstatusisnotued 00 Click PIN button now and wait for few seconds to one minute If a wireless access point with correct PIN code is found you ll be connected to that access point 30 Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About SSID BSSID E 1B Authe Encry PlanklnitialAP 00 30 4F 25 61 00 1 0x0000 WPA TKIP WIkin P 00 30 4F 41 44 14 4 WPA2 AES information Pin Code 26460161 J SSID MAC Address Authentic Encryption ga Planetnitial4P256100 00 30 4F 97 27 FC WPA PSK TKIP Connect Rotate Delete Y WPS associate IE 4 WPS probe IE You may have to click PIN for few more times to try again If you still can not connect to access point by this way please make sure the PIN code you provided to access point is correct Note This function is not support in the OS of Windows VISTA E Planet Wireless Utility 00 30 4F 42 07
22. an set it up depending upon their needs 12 What is DSSS What is FHSS And what are their differences Frequency hopping spread spectrum FHSS uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver Properly synchronized the net effect is to maintain a single logical channel To an unintended receiver FHSS appears to be short duration impulse noise Direct sequence spread spectrum DSSS generates a redundant bit pattern for each bit to be transmitted This bit pattern is called a chip or chipping code The longer the chip is the greater the probability that the original data can be recovered Even if one or more bits in the chip are damaged during transmission statistical techniques embedded in the radio can recover the original data without the need for retransmission To an unintended 36 receiver DSSS appears as low power wideband noise and is rejected ignored by most narrowband receivers 13 What is Spread Spectrum Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable secure mission critical communication systems It is designed to trade off bandwidth efficiency for reliability integrity and security In other words more bandwidth is consumed than in the case of narrowband transmission but the trade off produces a signal that is in effect louder and thus easier to detect provided that the receiver knows th
23. ation mark the resources are conflicting You will see the status of the Adapter If there is a yellow question mark please check the following 2 Make sure that your PC has a free IRQ Interrupt Request a hardware interrupt on a PC 3 Make sure that you have inserted the right adapter and installed the proper driver If the Adapter does not function after attempting the above steps remove the adapter and do the following 4 Uninstall the driver software from your PC 5 Restart your PC and repeat the hardware and software installation as specified in this User Guide Q cannot communicate with the other computers linked via Ethernet in the Infrastructure configuration Ans 1 Make sure that the PC to which the Adapter is associated is powered on 2 Make sure that your Adapter is configured on the same channel and with the same security options as with the other computers in the Infrastructure configuration Q What should do when the computer with the Adapier installed is unable to connect to the wireless network and or the Internet Ans 1 Check that the LED indicators for the broadband modem are indicating normal activity If not there may be a problem with the broadband connection 2 Check that the LED indicators on the wireless router are functioning properly If not check that the AC power and Ethernet cables are firmly connected 3 Check that the IP address subnet mask gateway and DNS settings are correctly
24. ave the same amount of data can be transmitted in a shorter time while allowing the Wi Fi device to remain longer in a low power dozing state 16 What is Gl Gl stands for Guard Interval It s a measure to protect wireless devices from cross interference If there are two wireless devices using the same or near channel and they are close enough radio interference will occur and reduce the radio resource usability 17 What is STBC STBC stands for Space Time Block Coding which is a technique used to transfer multiple copies of data by multiple antenna to improve data transfer performance By using multiple antennas not only data transfer rate is improved but also the wireless stability ee oe
25. ct WAT 415 00 30 4F D3 70 50 6 WEP Unknown Infrastruct default DO 30 4F 43 29 76 6 None Unknown Infrastruct FIRSTINS DO 30 4F 86 35 44 6 WEP Unknown Infrastruct gt i Connected lt gt wlan ap Rescan Connect Add to Profile Chapter 3 Configuration Utility The Configuration Utility is a powerful application that helps you configure the WNL U552 and monitor the link status and the statistics during the communication process When the WNL U552 is installed the configuration utility will be displayed automatically This card will auto connect to wireless device which has better signal strength and no wireless security setting m Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced DoS WPS Configuration About BSSID A Etre Authe Network 00 30 4F 09 BF A None Unknown Infrastruct 00 30 4F 03 3D A None Unknown Infrastruct D0 30 4F 28 60 PA TKIP WPA P Infrastruct 00 30 4F D3 70 WEP Unknown Infrastruct 00 30 4F 43 29 None Unknown Infrastruct FIRSTINS 00 30 4F 86 35 WEP Unknown Infrastruct gt The Configuration Utility appears as an icon on the system tray of Windows while the card is running You can open the utility by double click on the icon SE xmp 3 05 PM Right click the icon there are some items for you to operate the configuration utility e La
26. e parameters of the spread spectrum signal being broadcast If a receiver is not tuned to the right frequency a spread spectrum signal looks like background noise There are two main alternatives Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS 14 What is WMM Wi Fi Multimedia WMM a group of features for wireless networks that improve the user experience for audio video and voice applications WMM is based on a subset of the IEEE 802 11e WLAN QoS draft standard WMM adds prioritized capabilities to Wi Fi networks and optimizes their performance when multiple concurring applications each with different latency and throughput requirements compete for network resources By using WMM end user satisfaction is maintained in a wider variety of environments and traffic conditions WMM makes it possible for home network users and enterprise network managers to decide which data streams are most important and assign them a higher traffic priority 15 What is WMM Power Save WMM Power Save is a set of features for Wi Fi networks that increase the efficiency and flexibility of data transmission in order to conserve power WMM Power Save has been optimized for mobile devices running latency sensitive applications such as voice audio or video but can benefit any Wi Fi device WMM Power Save uses mechanisms included in the IEEE 802 11e standard and is an enhancement of IEEE 802 11 legacy power saves With WMM Power S
27. entered for the network 4 In Infrastructure mode make sure the same Service Set Identifier SSID is specified on the settings for the wireless clients and access points 5 In Ad Hoc mode both wireless clients will need to have the same SSID Please note that it might be necessary to set up one client to establish a BSS Basic Service Set and wait briefly before setting up other clients This prevents several clients from trying to establish a BSS at the same time which eee can result in multiple singular BSSs being established rather than a single BSS with multiple clients associated to it 6 Check that the Network Connection for the wireless client is configured properly If Security is enabled make sure that the correct encryption keys are entered on both the Adapter and the access point Q can t find any wireless access point wireless device in Site Survey function Ans 1 Click Rescan for few more times and see if you can find any wireless access point or wireless device 2 Please move closer to any known wireless access point 3 Ad hoc function must be enabled for the wireless device you wish to establish a direct wireless link 4 Please adjust the position of network card you may have to move your computer if you re using a notebook computer and click Rescan button for few more times If you can find the wireless access point or wireless device you want to connect by doing this try
28. ess point and you want to establish a secure connection to it you don t have to configure the wireless access point and setup data encryption All you have to do is go to the WPS setup page of this wireless card click a button and then press a specific button on the wireless access point you wish to establish a secure connection just three simple steps For older wireless access points it s possible to perform a firmware upgrade to become a WPS enabled access point Since they may not have a hardware button to press for WPS setup you can use an alternative WPS setup method input the pin code Every WPS compatible wireless network card comes with a unique WPS pin code you can just input the code to wireless access point and the wireless access point and wireless network card will do the rest for you This wireless network card is compatible with WPS To use this function the wireless access point you wish to connect to must support WPS function too Now please follow the following instructions to establish secure connection between WPS enabled wireless access point and your wireless network card Click WPS Configuration tab and the following settings will appear 265 Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About SSID BSSID c ID uthe Enery Pin Code 26461915 SSID MAC Address Authentic
29. eter Description Available Networks Rescan Button Connect Button Add to Profile Button This list shows all available wireless networks within range of your card It also displays the information of the networks including the SSID BSSID Signal Strength Channel Encryption Authentication and Network Type If you want to connect to any networks on the list double click the item on the list and the card will automatically connect to the selected network Click Rescan button to collect the new information of all the wireless networks nearby Click Connect to connect to the selected network Add the selected network to Profiles list 3 2 Profile The Profiles List is for you to manage the networks you connect to frequently You are able to Add Delete Edit Activate a profile fut Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About Profile List Profile Name SSID Channel Authenticat Encryption Network Parameter Description Profiles List The profiles list display all the profiles and the relative settings of the profiles including Profile Name SSID Channel etc Y This sign indicates the activated profile is been connecting MA This sign indicates the activated profile is not been connecting Add Delete Edit Button Click these buttons to add delete edit the selected profiles Activate Button
30. etween your wireless network card and access point is successfully connected by WPS and the information about access point you connected to will be displayed 28 t Planet Wireless Utility DU Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About SSID BSSID Eomp Authe Encry default 00 30 4F 28 60 10 11 Unkno WEP Pin Code 26461915 MAC Address Authentic Encryption Disconnect WPS Associate IE COT WPS Probe IE PIN Begin associating to WPS AP Sometime WPS may fail and you can click PBC button few more times to try again When an access point is connected you can click Disconnect to disconnect your wireless network card from a connected access point or select another WPS enabled wireless access point then click Connect to establish connection to selected access point if there are more than one WPS enabled access point found You can also click Rotate button and next access point on the list will be selected to establish connection If you want to delete a found access point from the list select it and click Delete button 3 7 2 WPS Setup PIN The PIN number of your wireless network card is an eight digit number located at the upper right position of configuration utility Remember it and input the number to your wireless access point as the WPS PIN code Please refer to the user manu
31. h your own product v rafal te lt Back M ne AAA cancel It is suggested to use PLANET Configuration Tool to manage the WNL U552 Click Next to continue PLANET WNL U552 InstallShield Wizard Setup Type E setup type that best mas lt Back Hem M concet If Optimize for performance mode is selected the Tx BURST option will be enabled to increase the transfer speed However the AP must support this feature as well If the target AP is complying with 802 11b g standard please select Optimize for WiFi mode a 6 You can see the installation progress in this screen PLANET W VNL U552 A a TANDEN aa a eV Please Wait 7 Please click Finish to finish the installation PLANET WNL U552 InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successfully installed PLANET WNL U552 Click Finish to exit the wizard InstallShield Driver Installation 1 Please insert WNL U552 into a vacant USB port of your PC 2 Windows will detect this device automatically When the Found New Hardware Wizard dialog box appears please click Cancel Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for Network Controller If your hardware came with an installation CD lt 3 or floppy disk insert it now Wha
32. hnology It also includes a new advanced encryption mechanism using the Advanced Encryption Standard AES AES is required to the corporate user or government users The difference between WPA and WPA2 is that WPA2 provides data encryption via the AES In contrast WPA uses Temporal Key Integrity Protocol TKIP WPA2 PSK WPA2 PSK is also for home and small business The difference between WPA PSK and WPA2 PSK is that WPA2 PSK provides data encryption via the AES In contrast WPA PSK uses Temporal Key Integrity Protocol TKIP When you have set the Authentication Type to Open Shared WPA or WPA2 you can also enable IEEE 802 1x setting to use the authentication server or certification server to authenticate client users None Disable the encryption mode WEP Enable the WEP Data Encryption When the item is selected you have to continue setting the WEP Encryption keys TKIP TKIP Temporal Key Integrity Protocol changes the temporal key every 10 000 packets a packet is a kind of message transmitted over a network This insures much greater security than the standard WEP security AES AES has been developed to ensure the highest degree of security and authenticity for digital information and it is the most advanced solution defined by IEEE 802 11i for the security in the wireless network 14 Note All devices in the network should use the same encryption method to ensure the communication WPA Pre Shared Key The
33. ificate Store is permitted A server designates an issuer as a trusted root authority by placing the issuer s self signed certificate which contains the issuer s public key into the trusted root certification authority certificate store of the host computer Intermediate or subordinate certification authorities are trusted only if they have a valid certification path from a trusted root certification authority Enter the authentication server name When selected the server name must match exactly the server 18 name found on the certificate Domain name must end in When selected the server name field identifies a domain The specified name certificate must use a server name belonging to this domain or to one of its sub domains e g zeelans com where the server is blueberry zeelans com but it may be any name used in the certificate name field 3 3 Link Status From the Link Status option you can view all the information of the network you are connecting to i Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced QoS WPS Configuration About Status Extra Info Link is Down Channel Link Speed Tx Mbps Rx Mbps Throughput Tx Kbps Ax Kbps Link Quality Signal Strenath 1 Signal Strength2 Signal Strength 3 Noise Level HT Bw E SNRO Parameter Descri
34. ivacy mechanism based on a 40 bit shared key algorithm as described in the IEEE 802 11 standard 8 What is TKIP TKIP is a quick fix method to quickly overcome the inherent weaknesses in WEP security especially the reuse of encryption keys TKIP is involved in the IEEE 802 111 WLAN security standard and the specification might be officially released by early 2003 9 Whatis AES AES Advanced Encryption Standard a chip based security has been developed to ensure the highest degree of security and authenticity for digital information wherever and however communicated or stored while making more efficient use of hardware and or software than previous encryption standards It is also included in IEEE 802 111 standard Compare with AES TKIP is a temporary protocol for replacing WEP security until manufacturers implement AES at the hardware level 10 Can Wireless products support printer sharing Wireless products perform the same function as LAN products Therefore Wireless products can work with Netware Windows 2000 or other LAN operating systems to support printer or file sharing 11 Would the information be intercepted while transmitting on air WLAN features two fold protection in security On the hardware side as with Direct Sequence Spread Spectrum technology it has the inherent security feature of scrambling On the software side WLAN series offer the encryption function WEP to enhance security and Access Control Users c
35. link setup DLS function This function will greatly improve the data transfer rate between WMM enabled wireless devices Please click Apply button on the right of this check box after you check or uncheck this box so corresponding settings in this window will be activated or deactivated respectively Input the MAC address of another WMM enabled wireless device you wish to establish a direct link here then click Apply to add this MAC address to DLS address table Input the timeout value of this WMM enabled direct link wireless device If the wireless device is not responding after this time it will be removed from DLS table If you want to remove a specific wireless device from DLS table select the device and click this button to remove it Note This function is not support in the OS of Windows VISTA ME Planet Wireless Utility 4 airlive Ludy FIRSTINS WRT 415 GLOBALHO KINGBANK 00 30 4F 42 07 ea Infrastruc 00 30 4F 26 E3 y Unknown infrastruc 00 30 4F 41 44 14 X WPA P infrastruc 00 30 4F 86 35 4 Unknown infrastruc 00 30 4F D3 70 y Unknown infrastruc 00 30 4F 9E EB yA Unknown infrastruc 00 30 4F CF DB 4 Unknown infrastruc m r Disconnected Rescan Add to Profile 295 3 7 WPS Configuration Wi Fi Protected Setup WPS is the latest wireless network technology which makes wireless network setup become very simple If you have WPS enabled wireless acc
36. nd France with Frequency channel restrictions Germany Greece Ireland Italy Luxembourg The Netherlands Portugal Spain Sweden and United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland WEEE regulation To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision User s Manual for PLANET 802 11n Wireless USB Adapter Model WNL U552 Rev 1 0 August 2007 Part No EM WNLU552 CONTENTS Chapter Introducir veces e E A 1 Ll A a A alae ie head E EE E E ER 1 12 Specification A A E A lee caanannaesaey A E EENS 2 1 37 Package Contents os ida 2 Chapter 2 Installation Proc UE 3 Chapter 3 Configuration UI 8 Sele Site Survey ecri ain ratere aE a EREE E AREATA E E A A A R Aa a 9 Bide DI Es 10 3 2 1 Add Profile COn A noia 11 3 2 2 Add Profile Authentication and Security oooococnnocccnoncnononcnonancnonnncconnnccnnnnos 13 3 2 2 1 802 1x Setting Certifica tics 15 D222 802 1x Setting CA SERVER ni 18 3 3 Link Sat ss hese cee ice code tessei ai 19 NS A A I A EAI A BR Le 20 DO o Aes et CEES BAe he Be EA OLE ie BE eae 21
37. nd alone authentication protocol be used within an 16 Session Resumption Identity Password Use Client Certificate Tunneled Authentication Protocol Identity Password encrypted tunnel TTLS supports any protocol within its tunnel including CHAP MS CHAP MS CHAPv2 PAP and EAP MD5 PEAP specifies that an EAP compliant authentication protocol must be used this card supports EAP MSCHAP v2 EAP TLS Smart card and Generic Token Card The client certificate is optional required for the authentication TLS Smart Card TLS is the most secure of the EAP protocols but not easy to use It requires that digital certificates be exchanged in the authentication phase The server presents a certificate to the client After validating the server s certificate the client presents a client certificate to the server for validation MD5 Challenge MD5 Challenge is the easiest EAP Type It requires the wireless station to enter a set of user name and password as the identity to RADIUS Server There are Disabled Reauthentication Roaming SameSsid and Always selections for you to choose whether to recovery the session in different status Enter the name as the identity for the server Enter the password as the identity for the server A client certificate is required for TLS and is optional for TTLS and PEAP This forces a client certificate to be selected from the appropriate Windows Certificate
38. ption Status Display the SSID and MAC ID of the network the card is connecting to Extra Info Display the link status Channel Display the number of the radio channel and the frequency used for the networking 19 Link Speed Mbps Display the transmission and reception rate of the network The maximum transmission rate is 54Mbps Throughput Kbits sec Display the speed of data transmitted and received Link Quality This bar indicates the quality of the link The higher the percentage the better the quality dBm If you want to know the signal strength in the unit of dBm select this check box Signal Strength This bar shows the signal strength level The higher percentage shown in the bar the more radio signal been received by the card This indicator helps to find the proper position of the wireless device for quality network operation Noise Level Display the noise level in the wireless environment 3 4 Statistics This option enables you to view the statistic information of the connection including transmit statistics and receive statistics You may reset the counters by clicking Reset Counter 4 Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced DoS WPS Configuration About Transmit Statistics Frames Transmitted Successfully Frames Fail To Receive ACK After All Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Frames Retransmitted Successfully
39. rk telephony VoIP and others When you enable WMM Wi Fi MultiMedia function of this network card you can define the priority of different kinds of data to give higher priority to applications which require instant responding Therefore you can improve the performance of such network applications wt Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced GoS WPS Configuration About WMM Enable CI WMM Power Save Enable C Direct Link Setup Enable Direct Link Direct Link Setup MAC Address Timeout Value DLS Status MAC Address Timeout Parameter Description WMM Enable WMM Power Save Enable Setting Check this box to enable WMM function Please click Apply button on the right of this check box after you check or uncheck this box so corresponding settings in this window will be activated or deactivated respectively Enable WMM power saving mode to save energy and lets your battery live longer Click this button to select the WMM data type which will suppress the function of power saving When this kind of data is transferring power saving function will be disabled Available data types are AC_BK Background Low Priority AC_BE Best Effort AC_VI Video First and AC_VO Voice First 24 Direct Link Setup MAC Address Timeout Value Tear Down Enable Enable or disable direct
40. t cause harmful interference and 2 this Device must accept any interference received including interference that may cause undesired operation Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Denmark Finland a
41. t do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue Next gt Cancel 3 Choose the first one Search for the best driver in these locations and tick the box of include this location in the search and then to click Browse to direct the hardware driver where is in C Program Files PLANET PLANET WNL U552 Driver Then click Next to continue Found New Hardware Wizard Please choose your search and installation options Sm Y Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed C Search removable media floppy CD ROM 4 Include this location in the search C Program Files PLANETSPLANET WNL USSADri Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware 4 The screen will appear to inform that you are installing PLANET WNL U552 Please click Continue Anyway to continue Hardware Installation A The software you are installing for this hardware PLANET WNL U552 has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this
42. to launch the auto run program Once completed a menu screen will appear Click the Configuration Utility hyperlink in the WNL U552 field to initiate the installation procedure Note If the menu screen does not appear click Start at the taskbar Then select Run and type E Utility WNL U552 setup exe where the E is your CD ROM drive Read the License Agreement carefully Click Yes to accept it and continue PLANET WNL U552 InstallShield Wizard License Agreement Please re PLANET Wireless Utiity for Windows 2000 XP Mista Copyright C PLANET TECHNOLOGY CORP Al Rights Reserved Thank you for purchasing PLANET Wireless product SOFTWARE PRODUCT LICENSE The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties as well as other intellectual property laws and treaties The SOFTWARE PRODUCT is licensed not sold 1 GRANT OF LICENSE This End User License Agreement grants you the following rights Installation and Use You may install and use an unlimited number of copies of the SOFTWARE PRODUCT Reproduction and Distribution You may reproduce and distribute an unlimited number of copies of the SOFTWARE PRODUCT provided that each copy shall be a true and complete copy including all copyright and trademark notices and shall be accompanied by a copy of this EULA Copies of the SOFTWARE PRODUCT may be distributed as a standalone product or included wit
43. to move closer to the place where the wireless access point or wireless device is located Q Nothing happens when click Launch config utilities Ans 1 Please make sure the wireless network card is firmly inserted into your computer s PCI slot If the Planet configuration utility s icon is black the network card is not detected by your computer Switch the computer off and insert the card again If this doesn t work contact the dealer of purchase for help 2 Reboot the computer and try again 3 Remove the driver and re install 4 Contact the dealer of purchase for help Q can not establish connection with a certain wireless access point Ans 1 Click Connect for few more times 2 If the SSID of access point you wish to connect is hidden nothing displayed in SSID field in Site Survey function you have to input correct SSID of the access point you wish to connect Please contact the owner of access point to ask for correct SSID 3 You have to input correct passphrase security key to connect an access point with encryption Please contact the owner of access point to ask for correct passphrase security key 4 The access point you wish to connect only allows network cards with specific MAC address to establish connection Please go to About tab and write the value of Phy_Addess down then present this value to the owner of access point so he she can add the MAC address of your
44. tures of EAP protocols Cisco controls the ability of other vendors to implement this protocol so it should be selected for use only when limited vendor choice for client access point and server products is not a concern When you have set up LEAP authentication you have to enter the user name and password of your computer 13 802 1x Setting Encryption Mode WPA WPA provides a scheme of mutual authentication using either IEEE 802 1x Extensible Authentication Protocol EAP authentication or pre shared key PSK technology It provides a high level of assurance to enterprises small businesses and home users that data will remain protected and that only authorized users may access their networks For enterprises that have already deployed IEEE 802 1x authentication WPA offers the advantage of leveraging existing authentication databases and infrastructure WPA PSK It is a special mode designed for home and small business users who do not have access to network authentication servers In this mode known as Pre Shared Key the user manually enters the starting password in their access point or gateway as well as in each wireless station in the network WPA PSK takes over automatically from that point keeping unauthorized users that don t have the matching password from joining the network while encrypting the data traveling between authorized devices WPA2 Like WPA WPA2 supports IEEE 802 1 x EAP authentications or PSK tec
45. uch PLANET WNL U552 Utilities Select Lauch PLANET WNL U552 Utilities to open the Configuration Utility tool e Use Zero Configuration as Configuration Utility Select Use Zero Configuration as Configuration Utility to use Windows XP built in wireless configuration utility Windows Zero Configuration to configure the card e Exit Select Exit to close the Configuration Utility tool 3 1 Site Survey When you open the Configuration Utility the system will scan all the channels to find all the access points stations within the accessible range of your card and automatically connect to the wireless device with the highest signal strength From the Site Survey all the networks nearby will be listed You can change the connection to another network or add one of the networks to your own profile list m Planet Wireless Utility Profile Link Status Site Survey Statistics Advanced DoS WPS Configuration About SSID RELAY wlan ap 620 WRT 415 default FIRSTINS BSSID Si Eo Ener Authe Network 00 30 4F 09 BF 10 1 None Unknown Infrastruct 00 30 4F 03 3D 10 1 None Unknown Infrastruct 00 30 4F 28 60 10 3 TKIP WPA P Infrastruct 00 30 4F D3 70 50 6 WEP Unknown Infrastruct D0 30 4F 43 29 76 6 None Unknown Infrastruct 00 30 4F 86 35 44 6 WEP Unknown Infrastruct gt Param
Download Pdf Manuals
Related Search