Planet Technology MAP-2105 User's Manual
Contents
1. 19 3 4 2 SNMP 19 3 4 3 Syslog Server 22 3 5 Tools 23 3 5 1 Ping 23 3 5 2 Download 24 3 5 3 Firmware Update 25 3 5 4 Settings 26 3 6 Reboot 28 3 7 Reset 28 3 8 Status 28 3 8 1 System 29 3 8 2 Interfaces 30 3 8 3 Services2. 32 3 8 4 MLRD 32 3 8 5 Route 33 3 8 6 Syslog 34 Chapter 4 Management Utility 35 4 1 Installation and Un installation 35 4 1 1 To install the MLRD Management Suite 35 4 1 2 To Uninstall the MLRD Management Suite 38 4 2 How to use MLRD Management Suite 39 4 2 1 AP Finder 39 4 2 2 Trap Viewer 40 4 2 3 MLRD Manager 42 4 3 Node Configuration using MLRD Manager 44 4 3 1 File gt Change SNMP Password 44 4 4 3 2 Status gt System
3. 45 4 3 3 Status gt MLRD 46 4 3 4 Config gt System 47 4 3 5 Config gt Network gt WAN 48 4 3 6 Config gt Network gt Route 51 4 3 7 Config gt Management gt SNMP Password 53 4 3 8 Config gt Management gt Access Control 55 4 3 9 Config gt Management gt Remote Syslog 56 4 3 10 Config gt Services gt NTP Client 56 4 3 11 Config gt Services gt Mobile IP 57 4 3 12 Config gt Services gt VPN Client 58 4 3 13 Commnad gt Download Upload 60 4 3 14 Command gt Reboot 60 4 3 15 Command gt Reset 61 4 3 16 Help gt About 61 5 Chapter 1 Introduction The MAP
4. 3 5 Tools 3 5 1 Ping Ping contains the following parameters Ping Enter an IP address to ping Number of pings Enter the numbers of ping packets to be send before displaying the result Start button Start the ping command Output Display the result of the ping command 23 3 5 2 Download Download contains the following parameters Release Version Display the revision number of the firmware TFTP Information Server IP Address Enter the TFTP server IP address File Name Enter the filename of the file located at the TFTP server File Type Please select either config or firmware File Operation Please select either upload download download and reboot Upload will send the file from device to TFTP server Note that only config can be uploaded to the server Download will get the file from TFTP server perform all the needed operation Download and reboot will get the file from TFTP server perform all the needed operation and reboot automatically 24 Apply button Press this button to save new settings and begin TFTP operation 3 5 3 Firmware Update Firmware page contains the following parameters Browse button Press this button to browse for firmware Upload button Press this button to upload the new firmware Do not switch off the device or do any other configuration settings Wait for it to fi
5. Specify a common name which is compulsory for all the participating mobile IP nodes Enable Backup Mobile Location Register Check the checkbox to enable the information backup to another server MLR Type 57 Select the type of MLR The available choices are Primary and Secondary Select Primary if this server is the main MLRD and secondary if it is configured as a backup server Peer MLR Addrss Specifies the IP Address of the backup server for MLR Backup Interval Specifies the time interval to wait in seconds before change from main to backup server 4 3 12 Config gt Services gt VPN Client This section describes the parameters in the VPN Client Panel The available parameters Enable PPTP Client Check the given checkbox to enable the PPTP service 58 VPN Server Enter the IP Address of the VPN Server Remote Network Subnet The Subnet IP Address of the Remote Network Remote Network Netmask The Netmask corresponding to the subnet IP Address of the Remote Network Authentication Username Specifies the username to authenticate to the server Authentication Password Specifies the password corresponding to the username to authenticate to the server Enable server side Authentication Check the given checkbox to enable the server side authentication Server username Specifies the username for the server side authentication This field is disabled when Enable server side Authent
6. Enter the server username for server to authenticate Servers Password Enter the server password for server to authenticate Save Config button Press this button to save new settings Back Link to previous page 3 3 3 NTP NTP Client contains the following parameters Enable NTP Client Enable or disable the NTP client Server 1 Enter IP address or hostname for the NTP server 18 Server 2 Enter IP address or hostname for the NTP server Server 3 Enter IP address or hostname for the NTP server Timezone Click on the drop down button and select the desired country Apply button Press this button to save new settings 3 4 System Management 3 4 1 Password Password contains the following parameters New Password Enter a new password New Password repeat Repeat the password entered above to confirm the changes Apply button Press this button to save new settings 3 4 2 SNMP 19 SNMP contains the following parameters SNMP version Select from v1 v2 v3 or both SNMPv2 Read only community Enter the v2 read only community 20 Read Write community Enter the v2 read write community SNMPv3 Read only username Enter the v3 read only username Read Write username Enter the v3 read write username Secret password Enter the password for the username configured above Secret passphrase Enter the passphr
7. Mobile IP Roaming Gateway MAP 2105 User s Manual 1 Copyright Copyright C 2006 PLANET Technology Corp All rights reserved The products and programs described in this User s Manual are licensed products of PLANET Technology This User s Manual contains proprietary information protected by copyright and this User s Manual and all accompanying hardware software and documentation are copyrighted No part of this User s Manual may be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form by any means by electronic or mechanical Including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use and without the prior express written permission of PLANET Technology Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be
8. 2105 is a mobile IP roaming gateway which is specifically designed for PLANET wireless mesh network It offers the full mobility to all users Not like the layer 2 only capability in ordinary AP the mobility defined in MAP 2105 is the ability of a user to change its attached node from one mesh AP to another while maintaining all existing communications and using the same IP address at this new link Remote printing remote login VoIP sessions and file transfers are some examples of applications whose communications are undesirable to interrupt when a mobile user moves from node to node 1 1 Features Provides Mobile IP capability for all wireless clients in the MESH network Secured HTTP management Supports VPN client Optimized for up to 500 mobile users 1 2 Package Contents The following items should be included MAP 2105 x 1 Power Adapter x 1 Quick Start Guide x 1 Management Utility and User s manual CD x 1 If any of the above items are damaged or missing please contact your dealer immediately 1 3 Network Planning The basic MESH Network topology can be planned as following Ethernet Switch DHCP Server Router MAP 2105 802 11b g Mobile User Mesh Relay Mesh Relay Mesh Gateway 1 The MAP 2105 should connect to the network that provide DHCP services the first time installation In this guide we will base on XRT 401D Internet Broadband Router as the
9. antenna where this may be done safely To the extent possible relocate the radio TV or other receiver away from the Switch Plug the Ethernet Switch into a different power outlet so that the Switch and the receiver are on different branch circuits If necessary you should consult the place of purchase or an experienced radio television technician for additional suggestions CE mark Warning The is a class B device In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures 2 Trademarks The PLANET logo is a trademark of PLANET Technology This documentation may refer to numerous hardware and software products by their trade names In most if not all cases these designations are claimed as trademarks or registered trademarks by their respective companies Revision User s Manual for PLANET Mobile IP Roaming Gateway Model MAP 2105 Rev 1 0 July 2006 Part No EM MAP2105 3 TABLE OF CONTENTS Chapter 1 Introduction 1 1 1 Features 1 1 2 Package Contents 1 1 3 Network Planning 1 1 4 Hardware In
10. display IP obtained from DHCP server Apply Button Submit the changes New settings are active after the device reboot 3 2 Network 3 2 1 WAN DHCPC Dynamically assigns an IP to this device Static IP Specify an IP address to this device Please complete the network parameters portion Configure Details and Save This button will lead to page according to the selected Interface Type mentioned above Pages invoked using Configure Details and Save Button are as follow DHCPC selected 12 Static IP selected Please enter the required field as follow IP Enter an IP address for this device Netmask Enter a network mask for this IP Apply Press this button to save new settings Back Back to previous page Gateway IP Address Specify the gateway IP address for this device Leave blank when DHCPC is enabled otherwise this entry will override the information obtained from DHCP server Primary DNS Server IP Address Specify the IP address of the primary DNS server for this device Leave blank when DHCPC is enabled otherwise this entry will override the information obtained from DHCP server 13 Secondary DNS Server IP Address Specify the IP address of the Secondary DNS server for this device Leave blank when DHCPC is enabled otherwise this entry will override the information obtained from DHCP server Domain Name Specify the domain name Apply P
11. example for DHCP server switch and router this installation can vary on the network planning The MAP 2105 should be installed in the same subnet to the Mesh Gateway for optimal performance Note The MAP 2105 is optimized for 500 user registration however the overall network performance may vary on the real environment and application in many aspects such as the bandwidth to the Internet the services sessions that the clients implement 1 4 Hardware Installation 1 Using Category 3 or higher UTP or STP cable connect the WAN port of MAP 2105 to a 10Mbps or 10 100Mbps Ethernet hub or switch and connect the management station to a hub or switch on the same LAN 2 Connect the power adapter to the receptor on MAP 2105 and plug the other end to a wall outlet or power strip Note ONLY use the power adapter supplied with the MAP 2105 Otherwise the product may be damaged 1 5 Startup the MAP 2105 To get the first management of the MAP 2105 please follow the following steps 1 Connect the MAP 2105 s WAN port to the network where can provide the DHCP services For example connect to the LAN port of XRT 401D 2 Power on a PC that also connects to the LAN port of the XRT 401D with DHCP or fixed IP address 3 Open the Internet browser and go to the DHCP status page of XRT 401D to check the WAN IP address of the MAP 2105 WAN MAC Address of MAP 2105 4 Check the MAC address from the Web page and also the MAC address
12. label of the MAP 2105 For example 09 64 as the figure above 5 Key in the IP address you found for MAP 2105 with https For example 2 https 192 168 0 100 6 The pop up screen will ask for user name and password By default please key in admin for both name and password Then bring up the screen 7 Now the MAP 2105 is ready for services 3 Chapter 2 Basic Network Setup This chapter describes a basic network environment formed by three mesh AP and one MAP 2105 The administrators can add the mesh AP freely according to real application The sample network topology is as below Ethernet Switch DHCP Server Router MAP 2105 802 11b g Mobile User Mesh Relay Mesh Relay Mesh G t Step 1 Gateway Configuration Configuration gt Local Service gt VPN Server Enable VPN Server checked Add New User by pressing Add button Username test it is defined by user Password test it is defined by user Assign IP 10 16 1 7 this address must be in the same IP segment as Gateway s Backhaul radio IP Comment Testing it is defined by user Status Enable 4 Configuration gt Local Service gt Mobile IP Enable Transparent Mobile IP Service checked Mobile IP Community Name PLANET it must be identical for all nodes in the same mesh network Mobile Location Register Address 10 16 1 7 the IP address assigned in VPN Server screen Step 2 Reboot the Gatew
13. perform the SNMP action Password The authentication password The default authentication method used is MD5 Pass Phrase The privacy pass phrase that must be more than 8 characters 4 3 2 Status gt System This submenu is basically a read only page provides user a brief summary regarding the MAP 2105 In order to configure the fields in this frame please refer to Configuring System Settings at the coming section The parameters at the System page Node Name A name for the MAP 2105 Node Location A location description of the MAP 2105 45 Status The node operation mode which can be Online or Offline Contact Name A generic name of the network administrator Contact Email A generic E mail Address of the network administrator Contact Phone A generic phone number of the network administrator Object ID The Object ID OID of the MLR Node specified to support the SNMP service Up Time A real time field that displaying the period of the node since it is turned on 4 3 3 Status gt MLRD This panel contains two tables CN Info table and Client Info table respectively CN is the abbreviation of Correspond Node where the table displaying the information regarding the MAP 2105 The information shown at this table IP Address Name IP Allocation of the nodes Whereas the Client Info table shows the information regarding the client nodes which is operate unde
14. settings Use Default button Press this button to restore the factory default configuration for this page 3 6 Reboot Reboot contains the following parameters Please enter the time to reboot seconds Enter a delay value so that the device will only reboot after the requested delay of time Reboot button Press this button to reboot the device If a delay is specified it will wait for that amount of time before rebooting the device 3 7 Reset Reset contains only one Reset to Factory Default button Press this button to restore the configuration for the device back to factory default 3 8 Status 28 3 8 1 System System contains the following parameters Uptime Display the uptime of the device since last booting Hardware Display the state of the hardware CPU Display information about the Central Processing Unit Memory 29 Display information about the memory state of the device Firmware Display the revision version of the firmware 3 8 2 Interfaces Interfaces contain the following parameters WAN Information Link to more detail information about the WAN interface Figure below shows the detail information of the WAN interface 30 Interface Display the state of the interface Running means the interface is up and running Hardware Address Display the hardware address of the interface IP address Display the IP address of the inte
15. to SNMP From Network Interface Check the checkbox to allowed network to access the SNMP Subnet The Subnet IP Address of the allowed network This field is disabled if From Network Interface is disabled Netmask The Netmask corresponding to the Subnet IP Address of the allowed network The bottom panel allowed user to configure details regarding the SNMP Trap Click on the Set Trap Configurations button to enable the settings The parameters at this section Enable SNMP Trap Check this option to enable the use of SNMP Traps SNMP Trap Version Specifies the SNMP version used for the SNMP Trap Three options are available SNMP v1 or v2c SNMP v3 and both Destination IP Address Specifies the destination IP Address to send the trap message to Fill in the IP Address of the Trap Viewer will enable the Trap Viewer to capture the trap release by this node 54 Community Specifies the secret password refer to the SNMP Trap Enable Trap Authentication Check the checkbox to enable the sending of trap when authentication failure occurs 4 3 8 Config gt Management gt Access Control User is able to configure the access control of the web based configuration page at this panel The parameters at this section From WAN Interface Check the checkbox to allowed the access from WAN device to web configuration From VPN Interface Check the checkbox to allowed the access from VPN device to web co
16. Address Specify the IP Address of the secondary DNS server for this device DNS Domain Name Specify an optional domain name for the DNS client Choose the desired Interface Type and hit the Configure Details button will lead to the configuration page for the specific interface type Config gt Network gt WAN gt Static Status This is a read only field that displays the status of the Static WAN IP Configuration The Static WAN IP will be disabled if the DHCP Client type is selected IP Address The IP Address of the Static WAN IP Address Netmask The net mask corresponding to the Static WAN IP Address Click on the Save and Enabled Static IP button to enable this type Config gt Network gt WAN gt DHCP Client 49 Status Display the status of the DHCP Client type This field is read only and will be disabled if the Static WAN IP is selected Click on the Enable DHCP Client button to enable this Interface Type 50 4 3 6 Config gt Network gt Route This section describes about the parameters for the Route table Enable Route Table Check this checkbox to enable the use of Route Table Route Table Displaying the current active entry in this device Config gt Network gt Route gt Route Table 51 This table consists of seven columns Subnet Specifies the Subnet IP Address of the route Netmask Specifies the Netmask corresponding to the Subnet IP Address of th
17. ase for the username configured above Access Control From WAN interface Check or uncheck the checkbox to allow or ban access for SNMP configuration purposes from WAN interface From VPN interface Check or uncheck the checkbox to allow or ban access for SNMP configuration purposes from VPN interface From Network Check or uncheck the checkbox to allow or ban access for SNMP configuration purposes from Network specified below Subnet Enter a network address for SNMP configuration purposes Netmask Enter the network mask of the configured network address above SNMP Trap Enable SNMP Trap 21 Enable or disable SNMP trap for this device Trap Community Enter the trap server community Destination Enter the IP address of the trap server Authentication failures Check or uncheck the checkbox to enable or disable sending of traps when authentication failures occur Apply button Press this button to save new settings 3 4 3 Syslog Server Remote Syslog contains the following parameters Status Display the current state of the remote syslog server Host to send syslog leave empty to disable Enter a hostname or IP address of the syslog server Leave this field empty if no remote logging required Save Config button Press this button to save new settings Use Default button 22 Press this button to restore default configuration for this page
18. ay Step 3 Relay Configuration Configuration gt Local Service gt Mobile IP Enable Transparent Mobile IP Service checked 5 Mobile IP Community Name PLANET it must be identical for all nodes in the same mesh network Mobile Location Register Address 10 16 1 7 the IP address assigned in Gateway VPN Server screen Step 4 Reboot the Relay Step 5 MAP 2105 Configuration Configuration gt Local Service gt VPN Client Enable PPTP Client checked VPN Server 192 168 0 99 the Gateway WAN IP address Remote Subnet 10 0 0 0 the subnet of Gateway s Backhaul radio IP Remote Netmask 255 0 0 0 the net mask of Gateway s Backhaul radio IP Username test it is identical as defined in Gateway VPN Server screen Password test it is identical as defined in Gateway VPN Server screen Step 6 Reboot the MAP 2105 Step 7 Check MAP 2105 status 6 CN Info Two correspondent nodes connected with relevant info Client Info Info of the mobile station recorded in the MAP 2105 7 Chapter 3 Web Configuration To start the web configuration 1 Start the web browser 2 Enter https IP Address of the MAP 2105 in the address box make sure HTTPS but not HTTP 3 Accept the security certificate and click Yes to proceed 4 The Web based configuration login page opens after the security certification has been accepted 5 Enter the user name and password By default the user name and password ar
19. b based Configuration Page 4 2 2 Trap Viewer The trap viewer is used to catch the alarm or trap send from the MAP 2105 which have their trap destination IP Address set to the user s IP Address In the MLRD Management Suite user can switch between the AP Finder and Trap Viewer by selecting the tab at the left bottom corner Alternatively this can be done by choosing View gt AP Finder or View gt Trap Viewer to toggle between the pages The following figure display the layout of the Trap Viewer 40 In order to start listen to the alarms hit on the Start button The foreground of the Start button will turn to green color when the trap viewer is running Conversely select the Stop button to disable the Trap Viewer where the foreground of the Stop button changes to red color The traps received will be displayed at the table provided The table displays the trap s description source IP Address trap severity and the time it is caught For more details regarding the trap select the desired row and click on the info button A dialog box will pop up and display more details of the node as shown by the following figure These traps should be deleted once they are reviewed or resolved In order to delete the trap from the table select the desired row or rows and click on the Clear button By default every alarm shown in the table will be logged into a file named Alarm_Default in the TrapLog folder at the application directory Howe
20. contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Compliance Statement This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the instructions provided with the equipment may cause interference to radio and TV communication The equipment has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If you suspect this equipment is causing interference turn your Ethernet Switch on and off while your radio or TV is showing interference if the interference disappears when you turn your Ethernet Switch off and reappears when you turn it back on there is interference being caused by the Ethernet Switch You can try to correct the interference by one or more of the following measures Reorient the receiving radio or TV
21. e both set to admin 8 6 After login successfully the Web based configuration main page is open which is appealed as below The following table describes the navigation button in brief Link Description System Settings Display the system settings page which consists of general information about the system Network Display or hide the links to WAN and Route WAN contains the configuration for network Route contains the configuration contains the configuration for static routing Local Service Display or hide the links to MLRD VPN Client and NTP MLRD contains the configuration for Mobile Location Register Daemon Mobile IP VPN Client contains the configuration for Virtual Private Network tunnel NTP contains the configuration for Network Time Protocol System Mgmt Display or hide the links to Password SNMP and Syslog Server Password 9 contains the configuration to updates password for web management server SNMP contains the configuration for Simple Network Management Protocol Syslog Server contains the configuration for syslog server Tools Display or hide the links to Ping Download Firmware Update and Settings Ping ping tools for network diagnostic Download contains configuration for TFTP file transfer Firmware Update web management firmware management Settings contains the configuration for web management server settings Reboot Displa
22. e route Gateway Specifies the gateway IP Address for this route Device Specifies the route devices for this route Two options are available WAN and VPN Gateway Device Specifies whether the entry is using the Gateway or Device option Status Specifies the status of this entry which can be Enable or Disable In order to add a new entry to the Route Table fill in the parameters required at the bottom of the table and click the Add button On the other hand if user wishes to edit the value or delete the existing entry in the table select the desired row and click Edit and Delete button respectively 52 4 3 7 Config gt Management gt SNMP Password This panel is basically separate to three different sections The upper panel is used to change or reset the SNMP v1 v2c and v3 passwords User can edit the password by entering the new password in the corresponding space retype in the confirm space and click on the Change button The parameters at this section Read Only Community Read Write Community Read Only Username Read Write Username Password 53 Pass Phrase The middle panel is to configure the Access control of the SNMP Click the Set Access Config button to load the settings The parameters at this section From WAN Interface Check the checkbox to allowed the access from WAN device to SNMP From VPN Interface Check the checkbox to allowed the access from VPN device
23. ersion 1 2c and 3 Thus for SNMP Version 1 or 2c only the Community field is compulsory whereas for SNMP Version 3 the Username Password and Pass Phrase fields is required to be filled 42 The upcoming section is going to describe regarding the configuration of the MAP 2105 via MLRD Manager 43 4 3 Node Configuration using MLRD Manager The MLRD Manager is a Java based graphical interface application that allow user to perform configuration of the specific MAP 2105 The configurations are done via Small Network Management Protocol SNMP Besides it also supports some action commands for instance download upload reboot and reset the factory settings for the particular node As overall the MLRD Manager consists of 5 submenus File Status Config Command and Help 4 3 1 File gt Change SNMP Password This option allows user to change the SNMP Password in case when the user desire to change the password from read only password to read write password or change the SNMP Version The Change Community window consists of the following parameters IP Address 44 This read only field shows the IP Address of the current MAP 2105 SNMP Version The Version of SNMP using to read and write data from to the node Two options are available 1 or 2C and 3 Community The community of the SNMP If the Version 1 or 2C is selected as the SNMP Version this field is required User Name The admin user name that given permission to
24. he Reset to Factory Default button to execute the command 4 3 16 Help gt About This option display the version of the MLRD Manager 61
25. ication is disabled Server password Specifies the password for the server side authentication This field is disabled when Enable server side Authentication is disabled 59 4 3 13 Commnad gt Download Upload The MAP 2105 also provides the download and upload file feature The following section describes the parameters of this pane Server IP Address Specifies the TFTP Server IP Address File Name Specifies the file name to be downloaded or uploaded File Type Select the file Type The available options are Config file and Firmware image Operation Type Choose the type of operation to perform Upload Download Download and Reboot After enter the parameters click on the OK button to start performing the command 4 3 14 Command gt Reboot After configure the settings using MLRD Manager the MAP 2105 must be rebooted before the settings take effect However beware that the reboot process would cause all the user who are currently connected to the network lose their connection until the unit has completely restart up and resume 60 Time to Reboot Specifies the time to delay before the reboot take place in seconds Click the Reboot button to execute the command 4 3 15 Command gt Reset Through this submenu user may set the MAP 2105 back to its default factory settings However performing the reset would cause all the settings done previously lost permanently Click t
26. in progress Note that every files and folder created during the installation will be removed 3 Uninstall Complete Un installation completed successfully 4 2 How to use MLRD Management Suite 4 2 1 AP Finder The AP Finder is used to discover the IP Address of the MAP 2105 available in the subnet The figure below illustrates the outlook of the AP Finder In order to start scanning for the nodes select the Scan button at the right pane of the AP Finder The system will search for the available MAP 2105 and display at the table Alternatively user can start the AP scan by select the Actions gt Scan Start from the menu bar On the other hand the Stop button or Actions gt Scan Stop at the menu bar is used to cancel the scan Check the Auto Rescan option in between the Scan and Stop button to enable the scanning process restart automatically after sleep for certain period User can configure this feature via Settings gt Auto Rescan option from the menu bar as well To set the time interval for rescanning choose Settings gt Rescan Interval from the menu bar A window will be pop up to prompt the user to enter the desired duration in seconds as shown at the following figure 39 The status bar located at the bottom of the AP Finder is displaying the status of the scanning process While the Select Adapter drop down list allow user to choose the adapter to configure the nodes Two options are available MLRD Manager or We
27. n which is the Delete button Use this button to delete the selected entry 15 3 3 Local Service 3 3 1 MLRD Mobile Location Register contains the following parameters Enable Mobile Location Register Service Enable or disable mobile location register service Mobile IP Community Name Enter a common name for this entry Mobile node s community name must be same for all participating mobile IP node Enable Backup Mobile Location Register Enable or disable the backup mechanism to another server This Mobile Location Register is Select primary if this server is the main Mobile Location Register server Select secondary if this server is configured as a backup server Peer MLR Address Specify the IP address of the backup server for Mobile Location Register Backup Interval Specify the backup interval from main to backup server Apply button Press this button to save the new settings 16 3 3 2 VPN Client VPN contains the following parameters Status Display the status of the VPN client Enable PPTP client Enable or disable PPTP client VPN Server Enter the IP address of the VPN server Username 17 Enter the username which is pre defined in VPN server of MESH Gateway Password Enter the password which is pre defined in VPN server of MESH Gateway Enable server side authentication Enable or disable server side authentication Servers Username
28. nfiguration From Network Interface Check the checkbox to allow specified network to access the web configuration Subnet The Subnet IP Address of the allowed network This field is disabled if From Network Interface is disabled Netmask The Netmask corresponding to the Subnet IP Address of the allowed network 55 4 3 9 Config gt Management gt Remote Syslog This submenu is used to set the remote syslog server IP Address who is receiving the syslog message from the MAP 2105 Remote Server Specifies the IP Address of the syslog server at the column provided In order to disable this feature please leave the column empty and click the OK button 4 3 10 Config gt Services gt NTP Client The NTP is a protocol that used to synchronize the clocks of computers to some time reference In this case it is used to synchronize the time of different nodes Parameters at this page Enable NTP Client Enable of disable the NTP client feature 56 Server 1 Server 2 Server 3 The network will connect to the NTP server 1 while Server 2 and 3 are used as back up servers Time Zone Choose the desired time zone from the list available 4 3 11 Config gt Services gt Mobile IP This section describes the parameters of the MLRD The parameters at this panel Enable Mobile Location Register Service Check the checkbox to enable the mobile location register MLR service Mobile IP Community Name
29. nish Failure in firmware update may cause the device to be unusable 25 3 5 4 Settings 26 Settings contain the following parameters Save Config Click on the mlrd cfg hyperlink to save the current configuration into local computer This configuration file can be used for debugging purpose as well as cloning settings to all other devices Restore Config Select the proper configuration to be restored Press the Browse button to select the correct file to be restored After this Press the Upload button to upload the selected file This action will override current configuration Please use with caution Install New Webserver Certificate Select the proper certificate to be uploaded to the internal web server Failing to do so may cause the web server to stop running Always use a tested web server certificate for this purpose Access Control From WAN Interface Check or uncheck the checkbox to allow or ban access for configuration purposes from WAN interface From VPN Interface Check or uncheck the checkbox to allow or ban access for configuration purposes from VPN interface From Network Check or uncheck the checkbox to allow or ban access for configuration purposes from Network Subnet Allow this network address for configuration access Netmask Network mask for the subnet configured above Save Config button 27 Press this button to save new
30. r the MAP 2105 The information displayed are MAC Address IP Address Previous CN IP Address Current CN IP Address The refresh button at the right top corner of the table is used to refresh and update both the table entries 46 4 3 4 Config gt System System panel is used to configure the System settings such as the administrator name and contact information as mentioned at the View System Status Descriptor A short description regarding this managed device 47 4 3 5 Config gt Network gt WAN This panel consists of two parts the upper part allow user to select the WAN Interface type to use and the lower part is used to configure the network settings In order to select a WAN Interface select on the desired type and type the Configure Details button Note the MAP 2105 does not support PPPoE connection type The network setting portion enables the configurations on the DNS Domain Name Service This feature translates the domain name into IP Address form which recognized by the Internet This translation is done through its own server If the primary server failed to perform the translation the secondary server will take over the process The parameters of the Network panel Gateway Specify the gateway for the static IP Address 48 Primary DNS Server IP Address Specify the IP Address of the primary DNS Server for this device Secondary DNS Server IP
31. ress this button to save new settings for Gateway IP Address Primary and Secondary DNS Server IP Address and Domain Name 3 2 2 Route Route contains the following Enable Static Routing Check or uncheck the box to enable or disable static routing for this device Apply Button Press this button to apply changes on Enable Static Routing Routing Table Display the current active entry for this device Add Button Press this button to add new entry to static routing The following figure shows the page invoked after using Add Button 14 Static Routing Entry contains the following parameters Subnet Enter a subnet IP address Netmask Enter a netmask of the subnet IP address above Gateway Select either gateway or device so that the traffic is through this selection Please enter IP address for gateway selection Device Select either WAN or VPN from the drop down list All the traffic from the specified subnet will be routed to this selected device Comment Optional comment can be added into this field Status Choose enable to activate this entry disable to deactivate this entry Apply button Press this button to save the settings back Link back to previous page Edit Button Press this button to edit the selected entry under the Routing Table A page similar to Static Routing Entry will be presented However it provides one extra butto
32. rface 31 3 8 3 Services Services page will display the status of each process and a corresponding Restart button to restart that particular service 3 8 4 MLRD MLRD contain the following information 32 CN Info Display the information of connected Correspondent Node Client Info Display the information of client register to the MAP 2105 3 8 5 Route Route contains the following parameters Refresh button Press this button to refresh the content of the output area Output Display the output of route command 33 3 8 6 Syslog Syslog contains the following parameters Refresh button Press this button to refresh the content of Output area Output Display the output of the syslog command 34 Chapter 4 Management Utility The PLANET MLRD Management Suite is a Java based software application designed specifically to manage the MAP 2105 which act as a server for the mesh nodes with the Mobile IP feature Generally the MLRD Management Suite is consists of three major sections the AP Finder Trap Viewer and MLRD Manager The AP Finder is utilized as a scanner to discover the MAP 2105 within the subnet Trap Viewer is able to receive and log the alarms sent by the nodes And the MLRD Manager is used to configure the nodes through Simple Network Management Protocol SNMP 4 1 Installation and Un installation 4 1 1 To install the MLRD Management Suite To ins
33. stallation 2 1 5 Startup the MAP 2105 2 Chapter 2 Basic Network Setup 4 Chapter 3 Web Configuration 8 3 1 System Settings 10 3 2 Network 12 3 2 1 WAN 12 3 2 2 Route 14 3 3 Local Service 16 3 3 1 MLRD 16 3 3 2 VPN Client 17 3 3 3 NTP 18 3 4 System Management 19 3 4 1 Password
34. tall the MLRD Management Suite on your terminal grab the MLRD_installer exe application file found on the accompanying CD ROM to any desired directory Double click the application file to start up the installation After completely extracting a loading window would show on the screen as illustrated Once loaded the installation wizard will be started up Follow the simple steps directed by the wizard 1 Introduction A brief introduction regarding the installer 35 2 Choose Install Folder Select the desired directory to locate the software application 3 Choose Shortcut Folder Set the shortcut path 36 4 Pre Installation Summary A review of the installation settings before starting the installation 5 Installing Display the progress of the installation 37 6 Install Complete Indicate the installation has been completed After complete the steps you can start up the MLRD Management Suite from the shortcut created 4 1 2 To Uninstall the MLRD Management Suite The MLRD Management Suite Uninstaller wizard is built along with the application You can uninstall the application by activate the wizard namely Uninstall_MLRD Management Suite exe which is located in the program folder Follow the three simple steps 38 1 Introduction About the uninstaller The un installation will be started once the Uninstall button is hit 2 Uninstalling The un installation is
35. ver options are available for the users to write into a different file or even disable the log feature To change a log file enter a new file name at 41 the Output File Name text box in the Settings column and press the Set button Besides choose Settings gt Output Filename from the menu bar would open a window to prompt the user for the new log file name To disable the log feature uncheck the Write to File check box in the Settings column and hit the Set button or uncheck the Settings gt Write to File menu item from the menu bar Under this circumstance the alarms deleted from the Trap Viewer will be gone forever The remaining two setting option in the Settings column is the Port and Community The Port defines the port number of the system to listen to the alarms while the Community defines the password to match the community of incoming traps Similarly user can fill in the value in the space provided and hit the Set button or select from the menu bar 4 2 3 MLRD Manager The MLRD Manager is the configuration pages of a MAP 2105 User may open the MLRD Manager to update or edit the settings of the node In order to start up the MLRD Manager choose the MLRD Manager from the drop down list at the left bottom corner of AP Finder as shown This action will open window to prompt the user for the SNMP Passwords The configurations can only be done with the correct password or community Note that the MLRD Manager is supporting SNMP V
36. y the reboot page which reboots the system from web management Reset Display the reset page which reverts the settings back to factory default Status Display or hide the links to System Interfaces and Services System Display information about system uptime hardware memory and firmware version Interfaces Display information about interfaces on board Services Display information about services running on the system MLRD Display information about the MLRD services Route Output the route information to be displayed on web page Syslog Output the system message log to be displayed on web page Vendor Web Site Links to vendor s web site Home Links to web management default page 3 1 System Settings 10 System Settings contains the following Device Name Enter a name for the device Device Location Enter a location that the device is located Contact Name Enter a name for the person to be contacted when consultant is needed regarding to the device Contact Email Enter an email address to be contacted when consultant is needed Contact Phone Enter a phone number to be contacted when consultant is needed Object ID Display the object identification OID of Simple Network Management Protocol Descriptor Add more description about this device WAN IP Address 11 Display the IP address of the WAN interface of this device For the first time operation it
Download Pdf Manuals
Related Search