Planet Technology GSD-Series User's Manual
Contents
1. 5 8 Port 10 100 1000Mbps Gigabit Ethernet Switch GSD Series User s Manual 1 Package Contents 2 Product Features Check the contents of your package for following Comply with IEEE 802 3 10Base T IEEE 802 3u parts 100Base TX IEEE 802 3ab 1000Base T Gigabit Ethernet Switch x 1 5 8 Port 10 100 1000Mbps Gigabit Ethernet ports User s manual x 1 Features Store and Forward mode with wire speed filtering and forwarding rates Power adapter x 1 Hardware based 10 100Mbps half full duplex and 1000Mbps full duplex mode flow control and auto negotiation Rubber feet x 4 If any of these are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair Integrated address look up engine support 4K absolute MAC addresses IEEE 802 3x flow control for full duplex operation and Back pressure for half duplex operation Automatic address learning and address aging Supports Auto MDI MDI X function Support CSMA CD protocol 3 Switch Front Panel Figure 1 1 amp 1 2 amp 1 3 amp 1 4 shows a front panel of GSD 503 GSD 504 GSD 803 GSD 804 Port lipar Fihr par a Q a O ww ce ol pi oo gE jee Figure 3 2 GSD 504 front panel Pi Tigaki Fibres Tu P OOO COR CO a ee 0 a a a Bt 78 Figure 3 3 GSD 803 front panel2. Figure 3 4 GSD 804 front panel LED Color Function PWR Lights to indicate that the Switch is powered on Lit indicate that the port is operating at 1000Mbps 1000 Green Off indicate that the port is operating at 10Mbps or 100Mbps LNK ACT Green Lit indicate the link through that port is successfully established Blinks to indicate that the Switch is actively sending or receiving data over that port Figure 1 5 amp 1 6 amp 1 7 amp 1 8 shows a rear panel of GSD 503 GSD 504 GSD 803 GSD 804 Tire Figure 5 1 GSD 503 rear panel WWW vIv a Te DL ae Figure 5 3 GSD 803 rear panel Power Notice 1 The device is a power required device it means it will not work till it is powered If your networks should active all the time please consider using UPS Uninterrupted Power Supply for your device It will prevent you from network data loss or network downtime 2 In some area installing a Surge suppression device may also help to protect your Switch from being damaged by unregulated surge or current to the Switch or the power adapter 6 Installing the Switch This part describes how to install your Gigabit Ethernet Switch and make connections to it Please read the following topics and perform the procedures in the order being presented Note This Switch does not need software configuration Desktop Installation To install the Switch on desktop simpl
3. bps Throughput packet per second 7 44Mpps 11 9Mpps Jumbo packet size Standards Conformance IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3ab Gigabit Ethernet IEEE 802 3x Full duplex flow control Standards Compliance Temperature Operating O 50 degree C Storage 40 70 degree C Humidity Operating operating 5 to 90 Storage 5 to 90 Non condensing Regulation Compliance FCC Part 15 Class A CE 8 Customer Support Thank you for purchase PLANET products You can browse our online FAQ resource at the PLANET Website first to check if it could solve you issue If you need more support information please contact PLANET switch support team PLANET online FAQ http www planet com tw en support faq php type 1 Switch support team mail address support switch planet com tw Copyright PLANET Technology Corp 2008 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners
4. y follow the next steps Step 1 Attach the rubber feet to the recessed areas on the bottom of the Switch Step 2 Place the Switch on desktop near an AC power source Step 3 Keep enough ventilation space between the Switch and the surrounding objects Note When choosing a location please keep in mind the environmental restrictions discussed in Product Specifications Step 4 Connect your Switch to network devices A Connect one end of a standard network cable to the 10 100 1000 RJ 45 ports on the rear panel of the Switch B Connect the other end of the cable to the network devices such as printer servers workstations or routers etc Step 5 Supply power to the Switch A Connect one end of the power cable to the Switch B Connect the 12V DC power adapter to a standard wall outlet When the Switch receives power the Power LED should remain solid Green 7 Product Specifications Hardware Specification hon 00 1000Base T Ports 5 Auto MDI MDIX ports 8 Auto MDI MDIX ports Pimensions mr 155 x 86 x 26 176 x 106 x 30 iss x86 x20 176 x 106 x 30 Weight kg 0 36 0 16 0 39 0 21 Power Requirement External power adapter 12V 1A Power Consumption 5 4 watts 18 BTU 8 1 watts 27 BTU Dissipation Iswiton Specification switch Processing Scheme Store and Forward Address Table Back pressure for half duplex IEEE 802 3x Pause Frame for full Flow Control duplex Switch fabric 10Gbps 16G
Download Pdf Manuals
Related Search