Home

Philips Signal Mirror CRV 1997-2003 User's Manual

image

Contents

1. Position the guides on the top of the Signal mirror Firmly press down on the bottom edge of the Signal Connect the Signal mirror mating connector to the into the slots on the top of the mirror mount Tuck mirror to snap it into position Signal mirror wire harness the wire harness to the back of the mirror housing Pivot the Signal mirror down on the mirror mount Wire Routing 1997 2001 Honda CRV 2002 2003 Honda CRV Pull out a portion of the rubber door insulation above the mirror mount l ia p ji Mount the mirror housin ny eee A VE back onto the door a using the 3 mirror mounting nuts Remove insert one of the included POT ame nec rubber grommets into the partly Re connect all OEM drilled hole t 7 fi wiring harnesses into the mirror mount area Remove any debris and Guide Signal mirror wire harness through the door frame and inside the rubber boot 1997 2001 Honda CRV Wire Routing Continued Pass the Signal mirror wire harness into the mirror mounting area and up through the rubber grommet Remove any Slack Bolt the mirror housing on the door using the three mirror mounting nuts Reconnect the factory mirror wire harness 2002 2003 Honda CRV Remove the footrest on the driver side floorboard by removing the two bolts Remove the plastic grommet in the upper right corner of the plastic trim in the corner of the door Dislodge the plastic grommet from the cen
2. and lift the underneath the mirror at the bottom edge of the mirror out of the mirror housing mirror housing Lift up on the bottom of the mirror to release it from the snaps NOTE In order to make room for the Signal mirror optics about 1 4 of the left edge of the Continue cutting down alongside the left edge of the mirrorimoint will need to heremoved Usea mirror mount and discard the excess molding pair of side cutters and begin cutting at the left edge of the mirror mount starting in the upper left corner Continued removal of any mirror mount surface interfering with Signal mirror optic may be necessary Carefully remove the foam insulation from the mirror housing sail Carefully peel back the plastic screw covers on the bottom of the mirror bracket Remove the three screws that hold the mirror bracket in place Mirror Replacement Continued 1997 2003 Honda CRV Using the shorter of the two wires from the kit Leave about 7 inches of wire exposed in the mirror Replace the three screws and screw covers on the starting from the inside of the mirror housing guide housing Guide the wire harness through the mirror bottom of the mirror bracket Guide the wire harness the end without the mating connector down bracket and remove any slack through the foam insulation and reposition the foam alongside the existing factory mirror harness insulation on the mirror bracket Lay the Signal mirror on a clean flat surface
3. ite www muthco com Or via E mail techsupport muthco com Door Panel amp Mirror Housing Removal 1997 2001 Honda CRV 2002 2003 Honda CRV Open door and lower window 1 Open door and lower window Remove screw and plastic grommet on inside corner of door 2 Remove plastic cover from corner of door Remove plastic cover from corner of door 3 Pop out and remove plastic inserts Door Panel amp Mirror Housing Removal Continued 1997 2001 Honda CRV 2002 2003 Honda CRV TE TAI T nag Ae a ee ae if Remove door handle plastic eae cover Disconnect the mirror wire he harness Fi IN Unscrew the 2 screws lt lt revealed by the removal of Remove three mirror anil a the door handle cover mounting nuts Pry out door handle as Remove mirror housing on shown Disengage latch assembly from door behind door handle and remove door handle Door Panel amp Mirror Housing Removal Continued 1997 2001 Honda CRV 2002 2003 Honda CRV Remove the 2 screws beneath armrest This section intentionally gt So Lift up an pl dor pane out slightly as shown j e ft bl a nk E i DA x 7 i Disconnect any wiring connection behind door panel Remove door panel from door Unscrew the 3 nuts holding the mirror housing to the door Remove mirror housing from door Mirror Replacement 1997 2003 Honda CRV While using sturdy gloves insert a small pry bar Pivot the mirror upward on its top edge
4. n vehicle Wire Identification 1997 2003 Honda CRV 15 Repeat all of the previous steps to replace the factory mirror on the passenger side door with the new S ignal mirror The vehicle s electrical wiring is located underneath the dash behind the fuse block assembly Guide the new wire harnesses from both sides of the vehicle to the electrical wiring Locate the GREEN WITH RED STRIPE and SINGLE GRAY RINGED wire from within the wire bundle Turn the ignition key so that electrical power is on and activate the driver side turn indicator Probe the wire with the wire tester to verify that flashing turn indicator power is present Label that wire as driver side turn 16 Locate the GREEN WITH YELLOW STRIPE and SINGLE GRAY RINGED wire from within the wire bundle NOTE There are two or more wires with the same color pattern Activate the passenger side turn indicator and probe the wire with the wire tester to verify that flashing turn indicator power is present Label that wire as passenger side turn USE THE INCLUDED WIRE TAPS AND FOLLOW THE FOUR STEPS ABOVE TO SPLICE INTO THE TURN INDICATOR WIRES 7 Make sure the harnesses are routed securely underneath the dash and enough slack is left for splicing 8 Splice the RED wire from the driver side harness into the green with red stripe and single gray ring wire previously labeled driver side turn 9 Splice the RED wire from the passenger side harness into the green with yello
5. ta nm T em M uN a Wie ee of rm te E lt ee _ Signal Mirror Installation Instructions Honda CRY 1997 2003 THE safety accessory of the 21st Century P N 210 0032 0 Rev B2 6 26 04 GG 2003 Muth Mirror Systems LLC Note Professional Installation Recommended Warranty does not cover damage to the vehicle or mirror housing due to improper installation The following installation instructions are to be considered as a guide only Door removal procedures indicator wire color and location may have changed since publication of these instructions The installer is responsible for any damage that may occur during installation INCLUDED ITEMS 1 left and 1 right Signal mirror l left and right wire harness 2 rubber tubes 2 rubber grommets 2 wire taps ring connector instruction manual REQUIRED TOOLS Ratchet with extension or ratcheting screwdriver Smm socket 10mm socket Small Philips screwdriver Medium Philips screwdriver Small pry bar Small utility knife Power drill 5 16 drill bit Wire crimper and stripper Needle nose pliers Masking tape Multimeter Sturdy gloves Safety glasses or goggles Please read instructions prior to installation PROBLEMS OR QUESTIONS Technical Assistance is available by calling Muth Mirror Systems Technicians at 1 800 844 6616 Monday through Friday Between 8 00 a m and 5 00 p m CST Or through the Muth web s
6. ter of the plastic trim and remove the trim from the corner of the door Route the Signal mirror wire harness from inside the rubber boot into the vehicle Wire Routing Continued 1997 2001 Honda CRV 2002 2003 Honda CRV Cut a small slit in the rubber door insulation level with the rubber boot between the door and door frame Guide the Signal mirror wire harness into the This section intentionally preexisting slit under the rubber door insulation I bl k above the mirror mount e fi A an n Pass the wire harness down through the rubber door insulation and out of the hole created in step 7 Wire Routing Continued 1997 2001 Honda CRV 2002 2003 Honda CRV 10 Remove the footrest on the driver side floorboard by removing the two bolts Remove the plastic pamela nega This section intentionally corner of the plastic trim in the corner of the door left b la n k Dislodge the plastic grommet from the center of the plastic trim and remove the trim from the corner of the door Wire Routing Continued 1997 2001 Honda CRV 2002 2003 Honda CRV 13 Slide the provided rubber tubing over the wire harness and guide 1 inch of tubing into the rubber door insulation There is a small hole in the top corner of the plastic trim piece along the door frame Guide the wire This section intentionally harness and rubber tubing into the hole and pass the b k wire harness into the efi t a
7. w stripe and single gray ring wire previously labeled passenger side 9 turn 10 Strip and twist together the ends of the black wires from both harnesses Crimp them together in the supplied ring connector and ground to a suitable nearby location on the metal framework of the vehicle 11 Activate each turn indicator to verify that the Si gnal mirrors are working 12 Replace any door accessories insulation plastic moldings and trim pieces

Download Pdf Manuals

image

Related Search

Related Contents

D GB NL F I E TR    Toshiba Satellite L750D-07N  thermalimaging....lwaukeetool.com  FLASH INFO_REFERENCEMENT OFFRES FRAIS DE SANTE  Catalogue Siemens Sinamics G110 (remplace le MM410)  Nachrüstdecoder-Set  Wireless thermostat user guide  Mod:E99/F40-A2  infos tri décembre 2012 - Accueil  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.