Philips SC478 User's Manual
Contents
1. Optional batteries 4x 1 5V AA for Baby Unit not included AC power adapter 230V AC 50 Hz Only use the 9 Volt DC 300 mA AC power adapter included Operating range Up to 300 metres in ideal conditions Range will be affected by walls doors etc Indoors the range may decrease to 50 meters Operating temperature 0 C to 40 C Standard Digital Enhanced Cordless Telecommunications DECT Resetting to default factory settings Factory Initialisation mode With this mode both units can be reset to the default factory settings Factory Initialisation can be used if problems occur which can not be solved by following the suggestions in chapter Problem solving Resetting must be done separately for each unit 1 Press and hold the I button 5 and 23 to switch on the unit SC478 book qxd 06 07 2004 09 46 Pagina 15 E ENGLISH 15 2 When the lights on the unit light up immediately press and hold the volume down button 11 and A 13 gt The unit has now been reset to the default factory settings Note By executing the factory initialisation mode Parent Volume Baby Volume and Baby Sensitivity are automatically reset to their factory default settings Personal preferences need to be set again Factory default settings are Parent Unit Volume level 1 1 light Baby Unit Volume level 3 3 lights Baby Unit Sensitivity level 5 5 lights Need Help In case you have an2. SC478 book qxd 06 07 2004 09 46 Pagina 1 Co baby monitor og oru sc SC478 DECT Instructions pour l utilisation Francais 16 Modo de empleo Espafiol 28 Bedienungsanleitung Deutsch 40 Gebruiksaanwijzing Nederlands 52 Istruzioni per l uso Italiano 64 Instruc es de uso Portugu s 76 OSnyies xprjonc EAAnvika 88 Bruksanvisning Svenska 100 Vejledning Dansk 112 Bruksanvisning Norsk 124 K ytt ohje Suomi 136 A w PHILIPS SC478 book qgxd 06 07 2004 09 46 Pagina 2 Belgi amp Luxemburg Belgien amp Luxemburg Belgique amp Luxembourg Belgium amp Luxembourg Tel 070 222303 Danmark Denmark Tif 808 82814 Deutschland Germany Phone 0180 53 56 767 Espa a Spain Phone 902 11 33 84 France Phone 08 25 88 97 89 EAAnvas Greece Phone 00800 3122 1280 Ireland Phone 01 764 0292 Italia Italy Phone 199118899 Helpline www p4c philips com Nederland Netherlands Phone 0900 8406 Norge Norway Phone 2274 8250 Osterreich Austria Phone 0810 001203 Portugal Phone 2416 3033 Schweiz Suisse Svizzera Switzerland Tel 0844 800 544 Suomi Finland puh 09 615 80 250 Sverige Phone 08 598 522 50 UK United Kingdom Phone 0870 9009070 SC478 book qxd 06 07 2004 09 46 Pagina 3 c PHILIPS eO A Baby Unit TI B Parent Unit SC478 book qxd 06 07 2004 09 46 Pagina 4 E 4 ENGL
3. ISH Your baby monitor SBC SC478 Philips is dedicated to producing caring reliable products that new moms and dads really need Products whose reliability and operating quality bring reassurance You can trust this Philips baby monitor to provide round the clock support by ensuring you can always hear your baby clearly no matter where you are in the house The 100 Digital DECT cordless telephone technology garantuees you hear only your own baby without any distracting noise Philips Baby Care Taking care together Important information Please read this guide carefully before using the baby monitor and keep it for future reference This baby monitor is intended as an aid It is not a substitute for responsible and proper adult supervision and should not be used as such Make sure the Baby Unit and adapter cable are always out of reach of the baby at least one metre away Never place the Baby Unit inside the baby s bed or playpen Never cover the baby monitor with a towel blanket etc Clean the baby monitor with a damp cloth Never use the baby monitor near water Dispose of used batteries in an environmentally friendly manner Safety precautions Check if the voltage indicated on the type plate of the adapters correspond to the local mains voltage before connecting to the mains power supply Do not use the set in moist places or close to water Do not expose the set to extreme heat or light eg dir
4. Parent Unit loudspeaker SC478 book od 06 07 2004 09 46 Pagina 7 ENGLISH 7 Getting the baby monitor ready Baby Unit For your convenience the Baby Unit can be mains or battery operated Mains operated use Connect the AC power adapter 7 to a mains socket and the cord to the DC power supply socket 12 of the Baby Unit gt The Baby Unit is now ready for mains operated use Battery operated use 1 Remove the battery compartment cover 8 Turn the Battery Lock knob to the left for this use a coin and slide the cover downwards 2 Insert four 1 5V AA size batteries noting the and configuration inside the battery compartment The batteries are not included we recommend non rechargeable Philips Alkaline batteries 3 Put the battery compartment cover back in place Slide the cover upward until it clicks in position Turn the Battery Lock knob to the right for this use a coin gt The Baby Unit is now ready for battery operated use The Baby Unit operates for a minimum of 25 hours on fresh batteries gt When the battery check light 10 flashes red the battery power is low The Baby Unit should now still operate for 15 minutes After that you should install new batteries Tips Switch off the Baby night light to save battery power when the Baby Unit is battery operated Remove empty batteries from the Baby Unit Battery back up As soon as the batteries are inserted battery b
5. Parent Unit to increase decrease the microphone sensitivity of the Baby Unit gt The sound level lights 25 on the Parent Unit give visual feedback about the setting for approximately 2 seconds 1 light minimum level lowest sensitivity All 8 lights 5 green and 3 red maximum level continuous transmission highest sensitivity Notes When set to maximum level continuous transmission the Baby Unit monitors continuously and all sounds regardless of level can be heard on the Parent Unit Battery operating time may decrease to approximately 12 hours during continuous transmission You can only change the Baby Unit microphone sensitivity if the connection between the Baby Unit and Parent Unit is established fe SC478 bock od 06 07 2004 09 46 Pagina 11 P ENGLISH 11 Talking back to comfort your baby 1 On the Parent Unit press and hold the TALK button 24 until the DECT SYSTEM LINK lights 3 and 15 of both units blink green Then talk clearly into the loudspeaker grill gt While the TALK button on the Parent Unit is being pressed no sounds from the Baby Unit can be heard on the loudspeaker of the Parent Unit 2 Release the TALK button when finished or when you wish to hear your baby again Explanation of features Monitoring baby silently Adjust the volume of the Parent Unit to the lowest level using the A A buttons 13 gt The sound level lights 25 visually alert you to baby s sounds The mo
6. aby To switch off the units again press and hold the OD buttons 5 and 23 gt The units will beep when they are switched off Note The Parent Unit beeps when it is accidentally switched off while monitoring SC478 book qxd 06 07 2004 09 46 Pagina 10 P 10 ENGLISH Adjusting loudspeaker volume Use the A A buttons 13 on the Parent Unit to increase decrease the loudspeaker volume of the Parent Unit Use the buttons 11 on the Baby Unit to increase decrease the loudspeaker volume of the Baby Unit gt The sound level lights 25 on the Parent Unit give visual feedback on the volume settings on both units for approximately 2 seconds 0 lights Parent Unit volume switched off 1 light monitoring baby silently 5 lights maximum Notes The volume of the Parent Unit can be switched off 0 lights The volume of the Baby Unit cannot be switched off A high pitched noise may occur in case the units are too close to each other To avoid this you should switch the Parent Unit volume off before placing the units close to each other You can only change the Baby Unit volume if the connection between the Baby Unit and Parent Unit is established Adjusting microphone sensitivity Press the SENSITIVITY button 14 on the Parent Unit gt The sound level lights 25 give visual feedback about the current sensitivity level for approximately 2 seconds Use the AA buttons 13 on the
7. ack up will be activated In case of mains failure during mains operated use the unit will automatically switch to battery operated use As soon as the mains supply is back on the unit switches to mains operated use again SC478 book od 06 07 2004 09 46 Pagina 8 8 ENGLISH Parent Unit 1 Remove the battery compartment cover 20 by lifting the cover outward from the bottom 2 Insert the two enclosed AA rechargeable batteries noting the and configuration inside the battery compartment 3 Put the battery compartment cover back in place First slide the upperside of the cover into the recesses in the battery compartment Then press the underside downwards until it clicks in position 4 Connect the AC power adapter 19 to a mains socket 5 Place the Parent Unit inside the charging base 17 gt The red charging light 18 lights up gt The Parent Unit can be operated now but you should leave it in the charging base until the batteries are fully charged at least 16 hours When the batteries are fully charged the Parent Unit can be taken out of the charging base and used cordlessly for up to 16 hours gt When the battery check light 21 lights up red the battery power is low Place the Parent Unit inside the charging base to recharge the batteries gt If the rechargeable batteries begin to lose their effectiveness replace them with two new rechargeable batteries Note Use rechargeable batteries onl
8. aging alert will sound To stop the paging alert press the Page button again or any button on the Parent Unit Operating range The SBC SC478 baby monitor has an open air operating range of up to 300 metres Walls ceilings large objects and even glass will decrease the operating range Depending on your local circumstances the operating range can decrease down to approximately 50 metres The system check function lights 4 15 and beeping sound on the Parent unit will in principle indicate to you the reliability of the connection between the Parent unit and Baby unit and whether you are out of range SC478 book qxd 06 07 2004 09 46 Pagina 13 e ENGLISH 13 Problem solving If a fault occurs first check the points listed below If you are unable to remedy a problem by following these hints contact the helpline or consult your dealer Under no circumstances should you try to repair the set yourself as this will invalidate the guarantee Problem Possible cause Solution DECT SYSTEM Parent Unit unit is not turned on Press the button 23 LINK light does Baby Unit unit is not turned on Press the T button 5 not light Batteries are low Replace recharge batteries Power adapter is not plugged in or Plug in power adapter or replace batteries batteries are exhausted Rechargeable batteries not inserted Place rechargeable batteries into Parent Unit High pitche
9. d noise Units are too close to each other ove Parent Unit away from Baby Unit Volume too high Decrease the Parent Unit volume Parent Unit Battery life is at an end Replace rechargeable batteries batteries do not using only NiMH rechargeable batteries charge Battery polarity misfitted Fit battery in correct polarity position Poor contact between Unit and Clean Charger contact with soft dry cloth Charger No sound Volume on Parent Unit is set too low Increase Parent Unit volume Sensitivity setting on Parent Unit too low Adjust sensitivity level of Parent Unit Units are out of range ove Parent Unit closer to Baby Unit Battery check light Batteries are low or empty lights Baby Unit or Parent Unit Recharge or replace batteries blinks Parent Unit Baby Unit Replace or remove battery DECT SYSTEM Units too far away from each other Decrease distance between units LINK light flashing Batteries are low Replace recharge batteries red System check Units cannot establish a connection Try solving the problem by using the factory alarm beeps on even when close to each other initialisation mode For this see chapter Parent Unit Factory Initialisation mode No power to one of both units Check button 23 on Parent Unit and D button 5 on Baby Unit SC478 book qxd 06 07 2004 09 46 Pagina 14 E 14 ENGLISH Technical specifications Power supply 2x AA rechargeable batteries 1 5V NIMH for Parent Unit included
10. ect sunlight To prevent electric shock do not open the cabinets of the Baby Unit Parent Unit and charger Avoid metallic contact e g metal clips keys between the battery contacts and the contacts in the charging base Risk of explosion if battery is replaced by an incorrect type Never use non rechargeable batteries NiMH batteries must be disposed of in accordance with applicable waste disposal regulations SC478 book od 06 07 2004 09 46 Pagina 5 ENGLISH 5 Environmental information No unnecessary packaging material has been used We have tried to make the packaging easy to separate into two mono materials cardboard box and polyethylene bags protective foam Please observe the local regulations regarding the diposal of packing materials exhausted batteries and old equipment Help line 2 General 4 mportant information 4 5 Functional overview 5 6 Getting the baby monitor ready 7 9 Monitoring your baby 9 11 Explanation of features 11 12 Problem solving 13 Technical specifications 14 Resetting to default factory settings 14 15 Functional overview A Baby Unit 1 Page button pages the Parent Unit in case you need to locate it Legend of product 2 Night light button illustration on inside flap switches on the nightlight 3 DECT SYSTEM LINK light lights orange unit switched on blinks red no connection for more than 30 seconds the system check alarm on the Parent Unit beeps bli
11. nks green slowly searching for connection blinks green fast transmitting sound when TALK button pressed lights green connection OK 4 Night lights 5 ON OFF button D switches the Baby Unit On and Off 6 Microphone MIC 7 AC power adapter 8 Battery compartment cover 9 Loudspeaker 10 Battery check light lt 4 lights up red when battery power is low 11 VOLUME Up Down buttons adjust the Baby Unit volume 12 DC power supply socket fe SC478 book od 06 07 2004 09 46 Pagina 6 6 ENGLISH B Parent Unit 13 Volume Up Down buttons A A adjust the Parent Unit volume 14 Sensitivity button adjusts the sensitivity of the Baby Unit speaker 15 DECT SYSTEM LINK light lights orange unit switched on blinks red no connection for more than 30 seconds the system check alarm on the Parent Unit beeps blinks green slowly searching for connection blinks green fast transmitting sound when TALK button pressed lights green connection OK 16 Loudspeaker 17 Charging base 18 Charging light 19 AC power adapter 20 Battery compartment cover 21 Battery check light lt 4 lights up red when battery power is low 22 Belt clip 23 ON OFF button OO switches the Parent Unit On and Off 24 TALK button talks to your baby via the Baby Unit 25 Sound level lights indicate that sound is detected by the Baby Unit indicate the sensitivity level of the Baby Unit microphone indicate the volume level of both Baby Unit and
12. re sound your baby makes the more lights light gt When no sound is detected all lights will be off gt If the volume of the Parent Unit is set to Off the Parent Unit will beep as soon as the second sound level light 25 lights red Checking that the units have established a connection Check that the DECT SYSTEM LINK light 15 on the Parent Unit lights continuously green to confirm that the connection between both units is reliable gt The DECT SYSTEM LINK light blinks green when the units lost connection with each other If connection is not established within 30 seconds DECT SYSTEM LINK light blinks red and the system check alarm on the Parent Unit beeps every 30 seconds This beeping can be suppressed for 3 minutes by pressing any button on one of the units SC478 book qxd 06 07 2004 09 46 Pagina 12 12 ENGLISH Switching the night lights on and off Press the button 2 on the Baby Unit to switch on the night lights Press the button again to switch off the night lights gt The nightlights dim and gradually switches off Note Switch off the night lights when operating the Baby Unit on batteries to conserve power Paging the Parent Unit If the Parent Unit is misplaced and the volume is switched off you can use the Page button on the Baby Unit to locate the Parent Unit Press the page button 1 on the Baby Unit gt The Parent Unit will automatically reset to medium volume level and p
13. terskrift Jalleenmyyjan nimi osoite ja allekirjoitus Nome morada e assinature da loja 6 month guarantee on rechargeable batteries 6 mois de garantie sur les piles rechargeables 6 meses de garant a para las pilas recargables 6 Monate Garantie auf wiederaufladbare Batterien 6 maanden garantie op oplaadbare batterijen Garanzia di 6 mesi sulle batterie ricaricabili Pilhas recarreg veis com 6 meses de garantia Eyy non 6 unvov oe erravadoprit uevec urrarap eg 6 m naders garanti p laddningsbara batterier 6 maneders garanti pa genopladelige batterier 6 m neders garanti pa de oppladbare batteriene Ladattavilla akuilla on 6 kuukauden takuu www philips com This document is printed on chlorine free produced paper Data subject to change without notice Printed in China C 06820 SS ffe
14. y Never operate the Parent Unit with other types of batteries Disposal of batteries e Dispose of used batteries in an environmentally friendly manner Do not mix old and new batteries or different types of batteries Remove Baby Unit batteries if the baby monitor is not to be used for long periods SC478 book qgxd 06 07 2004 09 46 Pagina 9 ENGLISH 9 Beltclip Connecting to the Parent Unit 1 Slide the wider side of the clip into the small rectangular recess on the back of the Parent Unit Make sure the pins on the underside are above E the circular recess 2 Press the clip downwards until it clicks in position Disconnecting from the Parent Unit Press the visible pin in the circular recess upwards and lift the clip outwards Monitoring your baby Switching on the units 1 Position the Baby Unit at least one metre away from your baby Never place the Baby Unit inside the baby s bed or playpen 2 Press and hold the button 5 on the Baby Unit to switch on the Baby Unit 3 Press and hold the button 23 on the Parent Unit to switch on the Parent Unit gt All lights light up for 2 seconds and then turn off again gt The DECT SYSTEM LINK lights 3 and 15 of both units light up orange then start blinking green The units now search for connection gt The DECT SYSTEM LINK lights 3 and 15 of both units light continuously green when the units have established connection You can now monitor your b
15. y questions about the SBC SC478 please contact our helpline for assistance You can find the number in the list on page 2 Before you call please read this manual carefully You will be able to solve most of your problems The model number of the baby monitor is SBC SC478 Date of purchase day month year SC478 book qxd 06 07 2004 09 47 Pagina 150 T Guarantuee certificate Certificat de garantie Garantieschein Garantiebewijs Certificado de garantia Certificato di garanzia Certificado de garantia Eyy non Garanticertifikat Garantibevis Garantibevis Takuutodistus year warranty ann e garantie Jahr Garantie jaar garantie afio garantia anno garanzia Xp voc evy non r garanti r garanti r garanti vuosi takuu afio garantia Type SBC SC478 Serial nr Date of purchase Date de la vente Verkaufsdatum Aankoopdatum Fecha de compra Date d acquisito Data da adquiric o Huepopnvia ayop g Ink psdatum Anskaffelsesdato Kjepedato Oatopaiva Dealer s name address and signature Nom adresse et signature du revendeur Name Anschrift und Unterschrift des Handlers Naam adres en handtekening v d handelaar Nombre direccion y firma del distribudor Nome indirizzo e firma del fornitore Ovoygarerrcvpo SieU8uvon kat urroypadr j rou eum rrpouneurr Aterf rsiljarens namn adress och signatur Forhandlerens navn adresse og unterskrift Forhandlerens navn adresse og un
Download Pdf Manuals
Related Search