Philips CMQ205/00 User's Manual
Contents
1. is filtered Adjust input level To ensure sound quality adjust input level to match it with the car audio s output voltage 1 Check the line output voltage of the connected car audio 2 Rotate INPUT LEVEL to select a matched voltage 0 3V to 6V Adjust bass boost To enjoy more bass sound 1 Set FILTER MODE at OFF or LPF mode 2 Slide BASS BOOST to 12dB position Tip If BASS BOOST is set at OdB position no extra bass will be boosted Note e If FILTER MODE is set at HPF mode the bass frequency will be filtered About the protector indicator The amplifier has a built in protection circuit to protect the transistors and speakers in following conditions e The amplifier is overheated e ADC current is generated in speakers e The battery voltage is too low or too high Or e The speaker terminals are short circuited When the PROTECTED indicator lights up in red the amplifier shuts down automatically In this case please EN 9 English 1 Take out the disc or tape and turn off the car audio Check the cause of the malfunction wN If the amplifier is overheated let it cool down Replace fuse If there is no power the fuse might be damaged and need to be replaced 1 Pullout the damaged fuse 2 Replace the fuse with the supplied fuse or buy a new fuse that matches the rating of the damaged fuse 30A x 1 If the fuse gets damaged immedia2. Connect the ground wire from the car to the GND socket Connect the remote wire from the car audio to the REM socket e With this connection you can turn on off the amplifier with the car audio Connect the power wire from the car battery to the 12V socket EN 7 English TC To a metal point of the car Remote output Less than 450mm 18 in Fuse 40A 12V car battery Tip e If your car audio does not have remote output connect the remote input terminal REM to the accessory power supply 4 Use your power amplifier Select filter mode Select Filter Mode according to the connected speaker type T Slide FILTER MODE to the selected position e HPF high pass filter Select this mode when mid range speakers and tweeters are connected for high frequency output e LPF low pass filter Select this mode when woofer and subwoofer are connected for low frequency output e OFF flat Select this mode when both tweeters and woofers are connected Select LPF frequency When FILTER MODE is set at LPF position you can select the range of frequency that is to be filtered Note e When FILTER MODE is set at OFF or HPF position LPF FREQUENCY does not work 1 Slide LPF FREQUENCY to the selected position e 80Hz More high frequency signal is filtered Select 80Hz if you prefer stronger bass effect e 180Hz Less high frequency signal
3. Register your product and get support at www philips com welcome CMQ205 EN User manual 3 ES Manual del usuario 13 PT BR Manual do Usuario 25 RU PyKOBOACTBO NOAb30BaTeAA 37 ZH CN MFE 49 PHILIPS Contents 1 Important 4 Safety 4 Notice 4 2 Your car power amplifier Introduction What s in the box Overview of the main unit Annum 3 Installation Mount the amplifier in car Connect speakers Connect car audio Connect power NNN OO 4 Use your power amplifier Select filter mode Select LPF frequency Adjust input level Adjust bass boost About the protector indicator Replace fuse 1 CO e 0 0 0 wo si 5 Product information 10 6 Troubleshooting 11 EN English 1 Important Safety e Read and understand all instructions before you use the apparatus If damage is caused by failure to follow instructions he warranty does not apply e This unit is designed for negative ground earth 12 V DC operation only Use only the supplied mounting hardware for a safe and secure installation Do not connect any active speakers with built in amplifier to the speaker terminals of the unit Doing so may damage the active speakers e To ensure safe driving adjust the volume to a safe and comfortable level e To avoid short circuit do not expose the apparatus remote control or remote control batteries to rain or water e Never expose the apparatus to direct
4. ed or stopped suddenly e The thermal protector is activated Reduce the volume e The ventilation outlet is blocked Remove any obstructions from the outlet Alternate noise is heard e The power connecting wires are installed oo close to the RCA pin cords e The ground wire is not securely connected to a metal point of the car egative speaker wires touch the car chassis The unit becomes abnormally hot e Place the amplifier in a well ventilated ocation e Use speakers with suitable impedance 2 8 ohm stereo 4 8 ohm bridged EN 11 English PHILIPS 2010 Koninklijke Philips Electronics N V All rights reserved CMQ205 00 UM V1 0
5. erformance with powerful bass and beats What s in the box Check and identify the contents of your package Amplifier Screw 25mm x 4 Gi Fuse x 1 Overview of the main unit 1 INPUT L R Connect car audio with RCA cable 2 OUTPUT L R e To connect additional amplifier with RCA cable for additional speakers 3 INPUT LEVEL e Adjust input level 0 3V to 6V FILTER MODE Set frequency filter at LPF low pass fitter HPF high pass filter or OFF flat mode 5 LPF FREQUENCY e Set LPF low pass filter frequency from 80Hz to 120Hz 6 BASS BOOST e Boost frequency for around 50Hz 12dB D POWER PROTECTED e Light in green when the amplifier is switched on e Light in red when the amplifier is abnormal and protected SPEAKER OUTPUT Connect to speakers or subwoofers EN 5 English 9 FUSE 30AX1 POWER To connect 12V DC power wire ground wire and remote control wire 3 Installation Note e Follow all mounting and wiring instructions Mount the amplifier in car You can mount the amplifier either under a seat or on the rear tray Note e To avoid interference do not place the amp
6. lifier too close to the car audio or antenna e The supplied mounting screws are 25mm long ake sure that the mounting board is thicker than 25mm d Place the unit on the location for installation 2 ark the positions of the four screw holes 3 Drill the holes with driller of approximately 4mm in diameter 4 ount the unit with the supplied screws Connect speakers Note e Use speakers with an impedance of 2 to 8 ohm 4 to 8 ohm when used as a bridged amplifier e Match the left right and terminals correctly Revised polarity may degrade sound quality Option 1 Stereo mode connect 2 speakers 4 ohm 4 ohm speaker speaker Option 2 Mono bridged mode connect 1 speaker S ch e 4 ohm speaker Option 3 Tri mode connect 3 speakers 4 ohm 3 ohm speaker speaker ee 8 ohm speaker Connect car audio Option 1 Line input connection Connect the amplifier to the car audio with an RCA cable not supplied Car audio unit LINE OUT SI w Option 2 Line output connection Connect the amplifier to another amplifier Connect power 1 Make the power connection as illustrated below
7. sunlight naked flames or heat e Clean the apparatus with soft damp cloth Never use substances such as alcohol chemicals or household cleaners on the apparatus 4 EN Notice Environmental information All unnecessary packaging has been omitted We have tried to make the packaging easy to separate into three materials cardboard box polystyrene foam buffer and polyethylene bags protective foam sheet Your system consists of materials which can be recycled and reused if disassembled by a specialized company Please observe the ocal regulations regarding the disposal of packaging materials exhausted batteries and old equipment Any changes or modifications made to this device that are not expressly approved by Philips Consumer Lifestyle may void the user s authority to operate the equipment 2010 Koninklij rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly ke Philips Electronics N V All 2 Your car power amplifier Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome Introduction With the amplifier you can enjoy high quality sound p
8. tely after it has been replaced the amplifier might have internal malfunction Consult qualified personal for repair 10 EN 5 Product information Note e Product information is subject to change without prior notice Power output 4ohm 75Wx2 RMS 2ohm 110Wx2 4ohm 220Wx1 bridged Total harmonic 0 09 distortion Signal to noise 100dB ratio Channel separation 50dB Frequency 5 50kHz response Input sensitivity 300mV 6V Input impedance 22k ohm Fuse rating 30A x 1 Dimensions D x 246 x 240 x W x H 54mm Weight 1 98kg 6 Troubleshooting To keep the warranty valid never try to repair he system yourself f you encounter problems when using this apparatus check the following points before requesting service H the problem remains unsolved go to the Philips web site www philips com welcome When you contact Philips ensure that the apparatus is nearby and the model number and serial number are available Power indicator does not light up e The connected car audio is not turned on e The fuse is blown Replace the fuse with anew one e The input level is not set correctly see Adjust input level The protector indicator lights up in red e The speaker terminals are short circuited Check the speaker connections The sound is too low e The input level is not set correctly see Adjust input level The sound is interrupt
Download Pdf Manuals
Related Search