Pentair QuickTouch QT4 User's Manual
Contents
1. a paper clip or other blunt instrument and adjust both 10 position configuration switches to matching settings Ifthe configuration switch setting at the Receiver does not match that of the Hand held Remote the communication link will not function 12345678910 ODO O O O O O O O n O O N IO OOOO Battery Compartment OL6E8L9OSVETL Receiver Hand held Remote NOTE All Program Switches are Factory set to ON If the IntelliTouch system has not been set to a new house address you should do so now To set anew House Address consult the main system instructions The Load Center System Control lights will blink repeatedly when a house address is being sent out If the system is sending a new house address the COM LINK and COMMAND lights will blink together repeatedly on the QT4 board If the system is sending an existing house address the COM LINK and COMMAND lights will blink alternately While this is happening press any button of the Hand held Remote The COM LINK and COMMAND lights will blink alternately The main system may now be RESET Wait for Auto Mode and the QT4 lights to stop blinking before resuming normal operation SECTION VII HAND HELD REMOTE B2. control circuits from a wireless Hand held Remote It is typically used for activating the spa circulation and for operating three auxiliary pieces of equipment such as lights jet pump air blower waterfall etc Each of the four functions on the Hand held Remote has an ON and an OFF button SECTIONIL KIT INCLUDES l qty Hand held Remote P N 520018 l qty Receiver with 9 ft cable 4 qty Plastic Anchors for mounting Receiver to concrete or stucco walls 4 qty Mounting screws for mounting Receiver to a flat surface SECTION III HAND HELD REMOTE The Hand held Remote will control four circuits Although the Remote is capable of duplicating any four circuits it has been preset at the factory to control the following Spa Push button activates the Spa circuit A Push button activates Auxiliary 1 circuit B Push button activates Auxiliary 2 circuit C Push button activates Auxiliary 3 circuit If you would like to control circuits other than Spa Aux1 Aux2 and Aux3 it is possible to make adjustments through the Indoor Control Panel or MobileTouch USING THE HAND HELD REMOTE To activate a circuit press and hold the appropriate ON button for at least a full second To deactivate press and hold the OFF button in the same manner IMPORTANT The Hand held Remote may be used with wet hands but should never be submersed in water as this could damage the unit If accidental submersion occurs dry
3. unit out by removing battery cover and removing battery Position unit so that water can drain out Reassemble when completely dry P N 520209 2 Rev A 7 25 03 SECTION IV CONFIGURING BUTTONS Configuring the Buttons of the 4 Function QuickTouch Wireless Hand held Remote to control your desired functions Rev A 7 25 03 Getting There MENU SETUP ADVANCED REMOTES gt _ gt gt a gt CONFIGURE QT WIRELESS gt gt Hint Before configuring the wireless remote assign names to the AUX circuits and or FEATURE circuits To configure the first button on your wireless remote press the top button at right The arrow indicates which button your are working on Hint The first button of the wireless remote is labeled SPA so configure this button for the spa mode as shown in the photo KA To configure the other three buttons on your wireless remote repeat the process using the next three buttons at right SPA LIGHT 2 JETS 3 AIR BLOWER 4 MENU SETUP ADU REM OT REMOTE BACK SAUE DOWN uP Use the DOWN UP buttons to scroll through the circuit names and find the function you would like to assign to the spa side button you are working on P N 520209 SECTIONV INSTALLATION Receiver The functional range of the wireless remote from Hand held Remote to Receiver is approximately 150 ft line of sight The receiver should be mounted at a convenient location on a flat
4. vertical surface a minimum of 5 ft above ground level to optimize the functional range of the hand held unit See Figure 1 for major features ACAUTION The receiver should be mounted a minimum of 8 to 10 feet away from any air blower which may be part of the equipment set The receiver will not operate properly if it is close to a blower that is operating 1 In order to mount the receiver it will be necessary to remove the two retaining screws located on the underside of the transceiver and carefully slide the transceiver case up and off of its back plate 2 Temporarily position the back plate against its mounting surface so that the receiver is oriented in an upright position with antenna pointing upwards 3 The circuit board will need to be temporarily removed Slide the board up and out of the back plate Use a pencil to mark the four mounting points and drill 3 16 in dia holes Insert the four plastic anchors provided 4 Feed a UL approved four 22AWG conductor cable through one of the drain holes at the bottom of the receiver enclosure The preferred wire color scheme is red yellow green and black If the drain holes are not used drill a hole through the bottom of the back plate and seal using a fitting with a few feet of conduit or some other sealant between the case and the cable 5 Reposition the back plate over the mounting points and secure with the four mounting screws provided 6 Strip the lead
5. ATTERY REPLACEMENT With normal use the battery should last for several years In the event the battery must be replaced slide the cover from the bottom of the Hand held Remote Slide the battery from the retainer clip and discard in accordance with local and or state ordinances Replace with 3V lithium battery number CR2032 or equivalent Slide battery cover onto remote and snap in place Rev A 7 25 03 5 P N 520209 TROUBLE SHOOTING Symptom POWER LED does not light COM LINK LED does not light or blink In normal operation LED will blink at least every 2 seconds COMMAND LED does not light when Hand held Remote button s is pressed unit fails to operate Unit functions but some circuits do not work or operate the incorrect circuit Unit fails to operate or fails to operate dependably at range Unit seems to turn on or off circuits without the user Hand held Remote Unit dependably turns equipment ON but once equipment is running it does not dependably turn equipment OFF or range is greatly reduced when equipment is running Unit operates but has greatly reduced range compared to prior function P N 520209 Load Center does not have power Defective cable or connection to the Load Center Defective receiver board Defective cable or connection to the Load Center Defective receiver board Address switches are incorrectly configured Hand held Remote battery has failed Defective Han
6. QuickTouch QT4 Owner s Manual 4 Function Hand Held Wireless Remote Control IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I APPLICATION SECTION Il KIT CONTENTS SECTION III HAND HELD REMOTE SECTION IV CONFIGURING BUTTONS SECTION V INSTALLATION SECTION VI CUSTOMIZING THE COMMUNICATION LINK SECTION VII HAND HELD REMOTE BATTERY REPLACEMENT TROUBLE SHOOTING WARRANTY Risk of electrical shock or electrocution It is required that the main power into the home be switched off at the main circuit breaker box Before installing this product read and follow all warning notices and instructions which are included Failure to follow safety warnings and instructions can result in severe injury death or property damage Call 800 831 7133 for additional free copies of these instructions Important Notice Attention Installer This manual contains important information about the installation operation and safe use of this product This information should be given to the owner operator of this equipment Pentair Pool Products D gt Pentair 1620 Hawkins Ave Sanford NC 27330 919 774 4151 Pool Products 10951 West Los Angeles Ave Moorpark CA 93021 805 523 2400 Because reliability matters most Rev A 7 25 03 1 P N 520209 SECTIONI APPLICATION Used in conjunction with the IntelliTouch Pool Spa Control System Provides switching of four remote
7. d held Remote or receiver Circuit selections incorrectly configured Undue electrical noise Too many obstructions between the Hand held Remote and receiver Receiver unit is too near the ground A nearby home is operating a similar wireless unit Undue electrical noise is being produced by one or more pieces of equipment in close proximity to the receiver Hand held Remote battery is failing Insure power is being supplied and that the Load Center operates correctly without the receiver installed Verify the function of the board using known good cable set Contact factory or service center Verify the function of the board using known good cable set Contact factory or service center Verify that the address switches on the Hand held Remote and receiver board are correct and match Replace Hand held Remote battery Contact factory or service center Verify settings at Control Panel MENU SETUP ADV REM QT REMOTE Relocate the receiver away from equipment such as blower motors Relocate the receiver in a location that provides fewer obstructions to the area the user commonly operates the Hand held Remote Relocate the receiver to maximize the distance between the receiver antenna and the ground Select an alternate address code for the Hand held Remote and receiver L e change the switches on both boards to an alternate but matching setting Relocate the receiver away from equipment such a
8. s blower motors Relocate the receiver in a location that provides fewer obstructions to the area the user commonly operates the Hand held Remote Replace Hand held Remote battery Rev A 7 25 03 For questions repairs replacement parts or information on possible Authorized Service Centers within your vicinity call Pentair Pool Products 800 831 7133 Or visit us on the Internet at www pentairpool com Rev A 7 25 03 7 P N 520209 Pentair Pool Products D gt Pentair 1620 Hawkins Ave Sanford NC 27330 919 774 4151 Pool Products 10951 West Los Angeles Ave Moorpark CA 93021 805 523 2400 Because reliability matters most P N 520209 Rev A 7 25 03
9. s of the wires about in and attach to controller screw terminals of terminal plug as shown in Figure 2 Carefully slide the circuit board back i Figure 1 into the back plate and connect the terminal plug 7 Then slide the Receiver case back onto the back plate and secure using the two retaining screws ACAUTION Water damage may occur if the enclosure retaining screws are not secured or a new hole is drilled for the cable and not sealed Do not seal drain holes RED YELLOW GREEN BLACK Load Center Feed the four conductor cable from the receiver up the low voltage raceway Open the control panel and fold down to make connections To the left of the board are the COM PORT connector s Strip the leads of the wires about 4 in and attach to controller screw terminals of any COM PORT terminal plug following the wiring diagram Close control panel high voltage cover panel and Load Center door Turn power to system back on Figure 2 P N 520209 4 Rev A 7 25 03 SECTION VI CUSTOMIZING THE COMMUNICATION LINK The communication link between the Receiver and Hand held Remote can be customized to prevent electrical interference To accomplish this there is a 10 position configuration switch located on the Receiver circuit board and inside the Hand held Remote Units are shipped from the factory with all switches in the ON position If you wish to change this setting use
Download Pdf Manuals
Related Search