Home

Pelco SPECTRA C3463M-B User's Manual

Contents

1. SW2 Switch 9 Coaxial UTP Cable SW2 9 should be set to the OFF position default if you are using coaxial cable If you are using unsheilded twisted pair UTP cable set SW2 9 to the ON position SW2 Switch 10 Termination Setting When connecting more than one Spectra IV dome system to a single controller terminate the unit farthest from the controller Termination is only required for the last dome in the series The dome drive is shipped from the factory in the unterminated OFF position To terminate the dome drive set SW2 10 to the ON position NOTE Dome termination is not required for Coaxitron control C3463M B 2 11 DOME DRIVE To install the dome drive 1 Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box 2 Push the tabs in Insert one side and then the other side 3 Continue pushing on the ends of the tabs until both sides click into place refer to Figure 2 Figure 2 Dome Drive Installation NOTE When removing a dome drive that has been in use caution should be taken to avoid direct contact with the top plate of the unit This section of the unit will be warm to the touch when first removed from an operating unit 4 Apply power to the Spectra dome system The system will start a configuration sequence When configuration is done the following information is displayed Pelco Spectra IV SL Spectra IV SE Version X XX D Address 1 P Address
2. opa hehe REOR RR M EO Aa DRE ba FOSTER PIS 11 Hub 11 9740 9760 9770 9780 onanan anann II e e e e 11 BD4000 7KBD40022 5 n oer o b t eae ed 11 LEM M ADA 11 C IA 11 STE Workstation ERE 12 s Ce 12 0 4100 9 45007 0 460070 8100 2 eins Rea epa diva ERR EGRE EE a loa aed 12 Digital Sentry System acus cert d des eor Aimee A Sn see 12 Digital Sentry DS COntrolPOINt Riot oe a Laat Gone RE 12 nte essence Mea OMe ils di habasta aha MR tale 12 23X LowLight Day Night Menu Tree RR e e e 13 27X Eowbight Day Night Menu Treen e oe OR ene Ib RI ue le ela So ee u WE Dele 15 SoX LOWLIght Day Night Menus a Ee Oe a Q sena Uu DS E 17 RENE es 19 System INFORMATION eom dens etd 20 DIP SWitculnrormation e ac ca teu ate texit d ces Moe eng oe Scene MALES etie 20 Display E 21 Ue lat Eh wor dst p
3. kas 22 Dome eee teste 23 r an s a es Aa ask 23 PDE cer ie hd ae aya y 23 AUTO FOCUS d sel a ote le 23 COIN 24 ZOOM atk ttn aca pa ys a aca p s Ra Oe OIM d xc tecta ud 24 ow Fight 24 Aan No cel Wo ca OAR Ck 25 Advanced Camera Settlnijs hath yay dae Shas wie ya wes Sarat ee gee 26 Sh tter Speed tee RE OO ANO ya Spa bi of asi lala Ae 26 ee estes EE RI NR E EE ile 26 RNC E 26 Auto Sharpness aka k da Pre akuy edel ode 27 Auto White Balance 2 Ahk Maton a qua RE 27 Backlight Compensation eed ve rb Ie obe DR a ete atu eL wes 2 Electronic Image Stabilization sre tote me Win e Ot pO XR n ete eter Gale ne es ated 27 Wide Dynamic Halte ge s soie me SDN M ka 27 Low lux Noise Reduction ye Rene
4. the joystick to position the cursor beside PRESET NUMBER Press Iris Open The cursor moves to the right b Move the joystick up or down to view selections Press Iris Open to enter selection Edit the preset label a the joystick to position the cursor beside EDIT PRESET LABEL b Press Iris Open The following informations appears LABEL FOR PRESET PRESET NUMBER 1234567890 ABCDEFGHIJ CANCEL KLMNOPORST UVWXYZ BACKSPACE abcdefghij SPACE uvwxyz Use the joystick to position the cursor beside a character Press Iris Open to enter selection To clear a character position the cursor beside BACKSPACE and then press Iris Open d When label is completed move the cursor to OK Press Iris Open to return to the Preset menu Edit the preset scene a the joystick to position the cursor beside EDIT PRESET SCENE b Press Iris Open Follow the directions displayed on the monitor Edit preset camera settings a the joystick to position the cursor beside EDIT CAMERA SETTINGS b Press Iris Open The EDIT CAMERA SETTINGS window appears Refer to Camera on page 23 and Advanced Camera Settings on page 26 to change preset camera settings Toedit the camera settings schedule use the joystick to position the cursor beside EDIT SCHEDULE Press Iris Open The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on page 53 with the following excepti
5. CLEAR PATTERN EDIT SCHEDULE REFERENCE INFO 0 PATTERN USAGE 100 REMAINING DIPSWITCH INFORMATION 12345678 1234567890 2 1 D ADDRESS 1 P ADDRESS 2 SW21 32PRESETS OFF SW22 CM9500 MODE OFF SW23 COAXSPIV COMM SW24 5 RS422 lt gt SW2 6 8 COMM 2400 N 8 1 SW29 UTC SOURCE COAX SW210 TERM OFF PRESS IRIS OPEN TO CONTINUE ADVANCED SETTINGS SUTTER SPEED AGC LIMIT AUTO IRIS AUTO IRIS LEVEL AUTO IRIS PEAK AUTO SHARPNESS SHARPNESS LEVEL AUTO WHITE BALANCE R GAIN B GAIN BACKLIGHT COMP WIDE DYNAMIC RANGE NEXT BACK EXIT LOW LUX NOISE REDUCTION ON VIDEO LEVEL HIGH FIELD ALIGN OFF LOW LIGHT SHARPNESS DEFAULT MINIMUM FOCUS DISTANCE 30 ZONES ZONE NUMBER 1 70NE NOT DEFINED EDIT ZONE LABEL EDIT ZONE ZONE ENABLED ZONE BLANKING CLEAR ZONE SPECTRA IV LANGUAGE SYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM MOTION AUTO FLIP PROPORTIONAL PAN PARK TIME MINUTES PARK ACTION SCAN SPEED DEG S PRESET FREEZE FRAME LIMIT STOPS SET MANUAL STOPS CLEAR MANUAL STOPS SET SCAN STOPS CLEAR SCAN STOPS SET AZIMUTH ZERO CLEAR AZIMUTH ZERO REFERENCE INFORMATION MANUAL LIMITS SET SCAN LIMITS SET WINDOW BLANKING STYLE BLANK ALL ABOVE BLANK ALL BELOW SET WINDOWS ENGLISH DISPLAY SETUP LABEL POSITION PRESET LABEL 2 SECS ZONE LA
6. 48 bene ete ede Mem LA eA 48 dein 48 ACtIVate AU ist bitte S ya EC Q e sua paqu e ayq eet cta t etae 49 s hukuy E 49 eoe C A Nc Ve NT 49 GIG AR e s tad Sola 50 50 e oer 51 prs ARD PC DL a Aa s 53 Event TypeA EAS lis ehe cats Roe 53 EV EMCI 54 Pdit Event tertie t De Feo M 54 WORT TI E TE 54 GIGAMEVENt seit ee EI pase cutee MD Za ele TT 55 edt Es ed ces dud 55 HONIG Asi LU M E M MEE 55 sedan P 55 dq Un ee E OE PNE TES MERITO B ts 56 Edo EE 56 Scheduled RIESCO 57 Reset Cycle Power Rebo0t tub TERRE UL pede Tai SR RP phe ne Mend INGISU ERR REMO RC EN NET E 58 Reset camera massa TET 58 Gycle Gamara UE S VINE DERE E ERES TAN ie PEE E Dee Toys 58 ve c
7. klmnopqrst uvwxyz Spectra IV dome systems feature password protection to prevent unauthorized changes to the dome settings An operator can open the System Information and Display Setup menus but cannot access any of the dome settings menus Controller keyboard commands cannot override password protected settings If a keyboard is used to set a preset pattern or zone the Enter Password menu appears The password must be entered before you can continue configuring the system At least one character must be entered to create a valid password This setting applies to Pressurized Spectra IV dome systems only 50 C3463M B 2 11 CLOCK SPECTRA IV DOME SETTINGS lt CAMERA gt TIME BASE lt MOTION gt TIME FORMAT lt AUTO TRACKING gt SET TIME LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt POWER UP gt lt DOME SETTINGS gt lt SYNC DATE FORMAT ACK ALERT RESET CAMERA CYCLE CAMERA POWER lt ZONES gt REBOOT SYSTEM EXIT lt PRESETS gt SET DIME PATTERNS i DAYLIGHT SAVINGS lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT BACK EXIT The clock is used to set the current date and time The date and time set in the Clock menu is used to configure events The date and time can also be displayed on the monitor when the menus are not being accessed
8. software version available memory DIP switch information and other diagnostic information System settings cannot be changed using this menu this information is for reference only Use the following steps to display the System Information menu 1 Use the joystick to position the cursor beside SYSTEM INFORMATION 2 Press Iris Open The SYSTEM INFORMATION menu opens DIP SWITCH INFORMATION The DIP Switch Information menu displays the dome drive s current DIP switch settings This provides a way to remotely view the DIP switch settings without removing the dome drive from the back box DIP SWITCH INFORMATION 12345678 1234567890 1 SW2 D ADDRESS 1 P ADDRESS 1 SW21 32PRESETS OFF SW22 9500 MODE OFF SW23 COAX SPIV SW2 4 5 RS422 lt gt SW2 6 8 COMM 2400 N 8 1 SW29 UTC SOURCE COAX SW2 10 TX RX TERM OFF PRESS IRIS OPEN TO CONTINUE This setting applies to Pressurized Spectra IV dome systems only 20 C3463M B 2 11 Display Setup LANGUAGE PRESET LABEL ZONE LABEL lt SYSTEM INFORMATION gt Z00M lt DISPLAY SETUP gt AZIMUTH ELEVATION lt DOME SETTINGS gt DIRECTION ALERT ALARM MESSAGE RESET CAMERA DATE TIME CYCLE CAMERA POWER EVENT LABEL REBOOT SYSTEM lt LABEL POSITIONS gt RESTORE FACTORY DEFAULTS EXIT BACK EXIT Display setup allows you to configure how labels are displayed on the monitor The following labels are available PRESET LABEL Identifi
9. 34 OFF ON OFF OFF OFF ON OFF OFF 35 ON ON OFF OFF OFF ON OFF OFF 36 OFF OFF ON OFF OFF ON OFF OFF 37 ON OFF ON OFF OFF ON OFF OFF 38 OFF ON ON OFF OFF ON OFF OFF 39 ON ON ON OFF OFF ON OFF OFF 40 OFF OFF OFF ON OFF ON OFF OFF ON OFF OFF ON OFF ON OFF OFF 2 OFF ON OFF ON OFF ON OFF OFF 43 ON ON OFF ON OFF ON OFF OFF m OFF OFF ON ON OFF ON OFF OFF 45 ON OFF ON ON OFF ON OFF OFF 46 OFF ON ON ON OFF ON OFF OFF 47 ON ON ON ON OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF OFF 49 ON OFF OFF OFF ON ON OFF OFF C3463M B 2 11 66 Table G Switch Settings for SW1 Pelco D Type Control 2 of 6 SPEGIRA SWITCH SETTING ADDRESS SW1 2 SW1 3 SWI 4 SWI 5 SW1 6 SWI 7 sw1 8 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OFF 54 OFF ON ON OFF ON ON OFF OFF 55 ON ON ON OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF OFF 57 ON OFF OFF ON ON ON OFF OFF 58 OFF ON OFF ON ON ON OFF OFF 59 ON ON OFF ON ON ON OFF OFF 60 OFF OFF ON ON ON ON OFF OFF 61 ON OFF ON ON ON ON OFF OFF 62 OFF ON ON ON ON ON OFF OFF 63 ON ON ON ON ON ON OFF OFF 64 OFF OFF OFF OFF OFF OFF ON OFF 65 ON OFF OFF OFF OFF OFF ON OFF 66 OFF ON OFF OFF OFF OFF ON OFF 67 ON ON OFF OFF OFF OFF ON OFF 68 OFF OFF ON OFF OFF OFF ON OFF 69
10. CCD 752 H X 582 V 540 TV lines 1 6 focal length 3 6 82 8 mm 23X optical zoom 12X digital zoom 2 9 4 2 5 8 seconds 54 at 3 6 mm wide zoom 2 5 at 82 8 mm telephoto zoom Automatic with manual override 0 55 lux at 1 50 sec shutter speed color 0 12 lux at 1 50 sec shutter speed B W Internal AC line lock phase adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 1 5 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB 61 27X MODELS DD427 Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed optical range Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise Wide Dynamic Range DD427 X Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise Wide Dynamic Range NTSC 2 1 Interlace 1 1 Progressive user selectable 1 4 inch CCD 768 H X 494 V 5540 TV lines 1 4 focal length 3 4 119 mm 35X optical zoom 12X digital zoom 3 2 4 6 6 6 seconds 55 8 at 3 4 mm wide zoom 1 7 at 119 mm telephot
11. CLEAR WINDOW CLEAR CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL WINDOW BLANKING RESTORE FACTORY DEFAULTS ZONE LABEL 2 SECS ZOOM 2 SECS AZIMUTH ELEVATION 2 SECS DIRECTION OFF ALARM MESSAGE 2 SECS DATE TIME ON lt LABEL POSITIONS gt RESTORE FACTORY DEFAULTS LABEL POSITION ZONE LABEL ALARM ALERT MESSAGE TITLE TEXT SAVE AND EXIT CANCEL HELP NE XX XX XXX X MM DD YYYY 12 00 00 AM This setting applies to Pressurized Spectra IV dome systems only Spectra IV systems that are not pressurized will not display this menu item NOTE The BACK and EXIT options do not appear in these menus due to space limitations See the individual menus in this document for complete configurations C3463M B 2 11 13 DOME SETTINGS lt CAMERA gt lt MOTION gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt LINE SYNC PRESETS PATTERNS LINE SYNC ON PRESET NUMBER PATTERN NUMBER LINE SYNC PHASE 0 PRESET NOT DEFINED lt PROGRAM PATTERN gt lt EDIT PRESET LABEL gt lt CLEAR PATTERN gt lt EDIT PRESET SCENE gt lt EDIT CAMERA SETTINGS gt REFERENCE INFO lt CLEAR PRESET gt PATTERN USAGE lt CLEAR CAMERA SETTINGS gt REMAINING REFERENCE INFORMATION AZIMUTH ELEVATION ZOOM CUSTOM C
12. MODEL XXXX XXXX SW2 6 8 COMM 2400 N 8 1 NE LANGUAGE 1 ENGLISH X XX SW29 UTC SOURCE COAX XX XX XXX X SW210 TX RX TERM OFF MM DD YYYY 12 00 00 AM LANGUAGE 10 ITALIANO X XX lt DIPSWITCH INFORMATION gt PRESS IRIS OPEN TO CONTINUE CAMERA ADVANCED SETTINGS MOTION AUTO TRACKING TYPE OF LIGHTING T SHUTTER SPEED AUTO FLIP AUTO TRACKING PICTURE MODE NORMAL AGC LIMIT PROPORTIONAL PAN DISPLAY SETUP AUTO FOCUS ON AUTO IRIS PARK TIME MINUTES SENSITIVITY SURE FOCUS OFF AUTO IRIS LEVEL PARK ACTION START TIME PT FOCUS LOCK AUTO IRIS PEAK SCAN SPEED DEG S ZOOM ZOOM LIMIT AUTO SHARPNESS PRESET FREEZE FRAME LOST ACTION ZOOM SPEED XXXX SHARPNESS LEVEL LIMIT STOPS RETURN LOW LIGHT LIMIT AUTO WHITE BALANCE SET MANUAL STOPS IR CUT FILTER R GAIN CLEAR MANUAL STOPS AUTO IR LEVEL B GAIN SET SCAN STOPS LOW LIGHT FOCUS BACKLIGHT COMP CLEAR SCAN STOPS E IMAGE STABILIZER SET AZIMUTH ZERO ADVANCED SETTINGS WIDE DYNAMIC RANGE CLEAR AZIMUTH ZERO NEXT BACK EXIT LOW LUX NOISE REDUCTION ON VIDEO LEVEL HIGH FIELD ALIGN OFF LOW LIGHT SHARPNESS DEFAULT MINIMUM FOCUS DISTANCE 30CM PATTERNS ZONES WINDOW BLANKING SET WINDOWS PATTERN NUMBER 1 ZONE NUMBER 1 STYLE WINDOW NUMBER PROGRAM PATTERN NOT DEFINED BLANK ALL ABOVE EDIT WINDOW LOCATION CLEAR PATTERN EDIT ZONE LABEL BLANK ALL BELOW EDIT WINDOW Z00M EDIT SCHEDULE EDIT ZONE SET WINDOWS EDIT SCHEDULE ZONE E
13. Models DD423 and DD423 X The default setting is 32X The zoom limit cannot be changed for 23X models 27X Models DD427 and DD427 X The default setting is 54X Cameras with 324X zoom 27X optical zoom and 12X digital zoom can be set for 27X 54X 108X 216X 270X or 324X 35X Models DD4CBW35 and DD4CBW35 X The default setting is 70 Cameras with 420X zoom 35X optical zoom and 12X digital zoom can be set for 35X 70X 140X 280X 350X or 420X Z00M SPEED Applies to 27X and 35X models only Zoom speed allows the user to define the speed at which the dome will go from full wide zoom to the optical zoom The zoom speed is set to 4 2 seconds and cannot be changed for 23X models Available zoom speed settings for 27X and 35X models include HIGH 3 2 seconds MEDIUM default 4 6 seconds LOW 6 6 seconds NOTE When using the HIGH setting the image may be out of focus until zooming stops LOW LIGHT LIMIT Applies to 27X and 35X models only Low light limit is the maximum duration in fractions of a second that the electronic shutter will remain open in low light conditions The default setting is 2 Refer to Table B for available settings Table B Low Light Limit Settings Setting Duration of Open Electronic Shutter 2 default 1 2 second 4 1 4 second 8 1 8 second 15 1 15 second 30 1 30 second 60 1 60 second C3463M B 2 11 IR CUT FILTER Spectra IV dome systems have two
14. an alert message appears on the screen describing the alert condition For example if pressure drops below 1 psig LOW PRESSURE is displayed The following system conditions will trigger an alert message System Condition Alert Message Temperature is above 140 F 60 C HIGH TEMPERATURE Temperature is below 40 F 40 C LOW TEMPERATURE Pressure is above 13 PSIG HIGH PRESSURE Pressure is below 1 PSIG LOW PRESSURE The difference between the temperature and DEW POINT HIGH HUMIDITY the dew point is less than or equal to 3 C The alert message will be repeatedly displayed until the system controller acknowledges the alert condition by selecting ACK ALERT in the main menu Once acknowledged the alert message changes to the configured acknowledge action ACK ACTION If the alert condition remains active after a period of time the alert message reappears on the monitor restarting the alert message cycle This cycle will continue to repeat until the alert condition is resolved REPEAT This setting programs how often an alert message is repeatedly displayed until the system controller acknowledges the alert condition The following are the settings CONSTANT The alert message is continuously displayed until acknowledged 15 MIN The alert message is displayed every 15 minutes for a 15 second duration until acknowledged 30 MIN The alert message is displayed every 30 minutes for a 15 second duration until acknowledged 60 MIN Th
15. function that can be performed automatically at a specific date and time For example suppose a camera is set to run in a continuous pattern that scans a parking lot during business hours Monday through Friday On Saturday and Sunday the camera needs to stop running the pattern and observe a gate First configure a preset to set the camera to observe the gate Second schedule an event to activate the preset on the weekends Finally a second separate event must be scheduled to end the first event and allow the camera to return to the pattern on Monday NOTE Events do not have a selectable duration A second event must be scheduled to end a previous event Events can be configured from the Preset Pattern Window Blanking Alarm or Aux menus or they can be configured from the Event menu Events are managed individually or as a group from the Event menu EVENT TYPE Any of the available event types can be selected from this menu or you may select ALL EVENTS to view and manage the events as a group The following are the settings for event type SCAN A scan event executes a specified scan random auto or frame scan using the limit stops and scan speed defined in the Motion menu Refer to Motion Settings on page 29 PARK A park event executes the user defined park action as specified in the Motion menu Refer to Park Action on page 30 WINDOW BLANKING A window blanking event activates or deactivates a previously defined window blank Th
16. gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt POWER UP POWER UP ACTION AUTO LINE SYNC PRESETS MOTION DETECTION EDIT DETECTION AREAS LINE SYNC ON PRESET NUMBER MOTION DETECTION ENABLED DETECTION AREA 1 LINE SYNC PHASE 0 PRESET DEFINED lt EDIT DETECTION AREAS gt LOCATION lt EDIT PRESET LABEL gt ACTIVATE AUX SENSITIVITY lt EDIT PRESET SCENE gt AUX TIME SECS DETECTION AREA 2 lt EDIT CAMERA SETTINGS gt LOCATION lt MOTION DETECTION gt BACK SENSITIVITY lt EDIT SCHEDULE gt EXIT DETECTION AREA 3 lt CLEAR PRESET gt LOCATION lt CLEAR CAMERA SETTINGS gt SENSITIVITY lt APPLY TO GLOBAL gt DETECTION AREA 4 REFERENCE INFORMATION LOCATION AZIMUTH SENSITIVITY ELEVATION ZOOM CUSTOM CAMERA SETTINGS ALARM SETTINGS RESUME ALARM NUMBER 1 AUX 1 MODE TOGGLE SEQUENCE SECS ALARM PRIORITY DWELL TIME SECS 1 RESET DELAY SECS ALARM ACTION AUX 2 MODE TOGGLE lt ALARM SETTINGS gt ACTIVATE AUX DWELL TIME SECS 1 ALARM CONTACT lt EDIT SCHEDULE gt lt EDIT SCHEDULE gt TITLE TEXT ENABLE TITLE TEXT lt EDIT TITLE TEXT gt EDIT THE PASSWORD EVENT EDIT EVENT 1234567890 OK TIME BASE INTERNAL CLOCK EVENT TYPE EVENT LABEL EVENTO ABCDEFGHIJ CANCEL TIME FORMAT 12 HOUR EVENT LABEL KLMNOPORST SET TIME 12 00 AM EVENT ACTIVE ON UVWXYZ BACKSPACE DATE FORMAT MM DD YYYY EDIT EVENT LABEL EVENT TIME 12 00 AM abcdefghij SPACE SET DATE 00 00 0000 lt
17. is no control Rebooting the system will cycle dome and camera power without changing the configured dome settings 58 C3463M B 2 11 Software Language File Upload The 45 data port of the dome drive allows access for on site setup testing and uploading of revised operating software and language files Pelco field service tool is required to perform these operations Field service tools include Pelco s remote monitor kit IPS RMK remote data port box IPS RDPE 2 and remote monitor cable IPS CABLE For instructions on how to upload revised operating software and language files refer to the Installation Operation manual supplied with the field service tool NOTE Only perform software uploads when necessary Software uploads do not need to be performed if the dome system is operating properly During a software language file upload a progress bar will appear indicating that data is being transferred to the Spectra dome system The default setting for data transmission is 115 2 KB per second Noisy and long run connections will slow the transmission rate C3463M B 2 11 59 60 Maintenance The Spectra IV dome systems do not require any special maintenance Occasionally dust may build up on the inside or the outside of the dome If this occurs turn power off to the unit and remove the lower dome from the back box Remove the dust from the lower dome using compressed air from a spray can Replace the lower dome follo
18. rectangle appears in the upper left corner of the screen refer to Figure 4 on page 38 f Use the joystick to place the blue rectangle over the desired detection area g Press Iris Open to make a selection This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 37 MOTION DETECTION AREAS Figure 4 Motion Detection Areas 2 Set the sensitivity of the motion detection area a Position the cursor next to SENSITIVITY for DETECTION AREA 1 2 3 or 4 b Press Iris Open the cursor moves to the right C Usethe joystick to select one of the following sensitivity levels HIGH The sensitivity level is high MEDIUM default Average sensitivity LOW The sensitivity level is low d Press Iris Open to make selection NOTE Motion detection is not guaranteed to catch 100 percent of activity Activate Aux Command Motion detection can be configured to trigger an auxiliary command when motion is detected The following are the settings for ACTIVATE AUX OFF default Motion detection will not trigger an AUX command 1 Triggers a command to AUX 1 2 Triggers a command to AUX 2 Aux Time Aux time is the length of time the auxiliary will remain on after motion is detected Available settings for AUX TIME are 1 to 60 seconds EDIT SCHEDULE The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on page 53 with the following exceptions In the Edit Schedule menu the event t
19. settings saved Camera settings can also be changed manually from the Camera menu following the original camera event e event type cannot be changed if you are accessing it through the Edit Schedule option from the Preset Pattern Window Blanking Alarm or Aux menu This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 53 EVENT LABEL Set the event label to NEW to create a new event Use the following steps to manage an existing event 1 Use the joystick to position the cursor beside EVENT LABEL Press Iris Open 2 Move the joystick up or down to scroll through the events Press Iris Open to enter selection As you scroll through the events the reference information at the bottom of the screen displays the corresponding details for each event To view a list of all events and their details refer to List Event on page 55 EDIT EVENT LABEL After an event is configured the label can be changed using the following steps 1 Use the joystick to position the cursor beside EDIT EVENT LABEL 2 Press Iris Open The following information appears EDIT EVENT LABEL EVENT 1 1234567890 OK ABCDEFGHIJ CANCEL UVWXYZ BACKSPACE abcdefghij SPACE klmnopqrst uvwxyz amp 3 Use the joystick to position the cursor beside a character Press Iris Open to enter the selection To clear a character position the cursor beside BACKSPACE and then press Iris Open 4 When
20. the label is completed move the cursor to OK Press Iris Open to return to the Edit Schedule menu After an event is labeled the label will be displayed when the event is activated according to the display setup values for this label Refer to Display Setup on page 21 for instructions on how to change the way a label is displayed on the monitor EDIT EVENT Use the following steps to edit an event 1 Use the joystick to position the cursor beside EDIT EVENT 2 Press Iris Open The following information appears EDIT EVENT EVENT LABEL EVENT 1 EVENT ACTIVE NO EVENT TIME 12 00 AM EVENT OCCURS SUNDAY OFF MONDAY OFF TUESDAY OFF WEDNESDAY OFF THURSDAY OFF FRIDAY OFF SATURDAY OFF HOLIDAY SKIP HOLIDAYS EVENT TYPE PRESET NUMBER 1 BACK EXIT a Use the joystick to position the cursor beside EVENT ACTIVE Press Iris Open Scroll to select NO to leave the event inactive or YES to activate the event Press Iris Open to confirm your selection b Use the joystick to position the cursor beside EVENT TIME Press Iris Open Scroll through the hours until the desired time appears Use the joystick to move the cursor to the right Scroll through the minutes until the desired time appears Press Iris Open to select the time Use the joystick to position the cursor beside SUNDAY Press Iris Open The available options are OFF and ON Press Iris Open to confirm your selection 54 C3463M B 2 11 d Follow the instructions in the
21. to select the character To clear a character position the cursor beside BACKSPACE and then press Iris Open 4 When the title is completed move the cursor to OK Press Iris Open to return to the Title Text menu 5 Enable the title text label by doing the following a Move the cursor beside ENABLE TITLE TEXT b Press Iris Open The cursor moves to the right c Move the joystick up or down to view the selections Select ON and then press Iris Open to enable the title text This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 47 ALERT 48 LANGUAGE lt SYSTEM INFORMATION gt lt MOTION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT lt CAMERA gt REPEAT ACK ACTION lt AUTO TRACKING gt ACTIVATE AUX lt POWER UP gt lt CURRENT READING gt lt LINE SYNC gt RESET ALERT lt PRESETS gt RESET CAMERA lt PATTERNS gt BACK CYCLE CAMERA POWER lt ZONES gt EXIT REBOOT SY EXIT STEM lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT NOTE The Alert option applies to Pressurized Spectra dome systems only Spectra IV systems that are not pressurized will not display this menu item Sensors strategically placed inside the pressurized dome system continually monitor pressure temperature and dew point If internal conditions reach unacceptable levels
22. to the T1 setting Picture Mode becomes visible and is automatically reset to Normal AUTO FOCUS Auto focus allows the lens to remain in focus during zoom in zoom out and motion functions There are two auto focus settings ON default f auto focus mode is set to ON the camera will focus automatically when using pan tilt and zoom PTZ functions OFF Focus is operated manually To focus press the Focus Far or Focus Near button on the controller Sure Focus Applies to 27X and 35X models only When sure focus is enabled and all PTZ motions are stopped the camera will attempt to find a fixed focus position and lock to an object in the scene If a focus lock is acquired or a specific amount of time has expired with no focus lock the focus position remains fixed until PTZ is resumed NOTE auto focus is OFF sure focus is disabled and hidden from the menu This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 23 24 PT Focus Lock Pan tilt PT focus lock holds the focus position of the lens during PTZ to maintain accurate focus between scenes especially during the execution of presets and in low light scenes There are two settings ON PT focus lock is enabled OFF default PT focus lock is disabled ZOOM LIMIT Applies to 27X and 35X models only Zoom limit allows the user to define a limitation on the amount of telephoto zoom The settings vary depending on camera model 23X
23. 1 Dome Settings CAMERA LANGUAGE lt CAMERA gt TYPE OF LIGHTING lt SYSTEM INFORMATION gt lt MOTION gt PICTURE MODE lt AUTO TRACKING gt AUTO FOCUS lt DISPLAY SETUP gt PUWERUPS lt DOME SETTINGS gt ACK ALERT lt LINE SYNC gt PT FOCUS LOCK lt PRESETS gt ZOOM LIMIT RESET CAMERA lt PATTERNS gt ZOOM SPEED CYCLE CAMERA POWER lt ZONES gt LOW LIGHT LIMIT REBOOT SYSTEM lt WINDOW BLANKING gt IR CUT FILTER EXIT lt ALARMS gt AUTO IR LEVEL lt AUX gt LOW LIGHT FOCUS TLE TEXTS lt ADVANCED SETTINGS gt LERT gt LEAR gt BACK lt PASSWORD gt EXIT lt CLOCK gt lt EVENT gt BACK EXIT TYPE OF LIGHTING Pelco has calibrated settings that optimize the white balance and the picture for several lighting conditions There are two settings T1 default For use in outdoor applications T2 For use in indoor applications Picture Mode Applies to 27X and 35X models only Picture mode offers enhanced color and brightness depending on the scene Available settings are NORMAL default and ENHANCED When picture mode is set to ENHANCED the camera enhances colors and the overall picture NOTES e The scene on your monitor will darken temporarily when you change the picture mode setting When Type Of Lighting is set to T1 and Picture Mode is set to Enhanced and you change the setting for Type Of Lighting to T2 Picture Mode is no longer visible in the menu When Type Of Lighting is returned
24. 1 OFF ON ON ON ON OFF OFF OFF 32 ON ON ON ON ON OFF OFF OFF C3463M B 2 11 Table G Switch Settings for SW1 Pelco D Type Control 7 of 6 SWITCH SETTING ADDRESS SW1 2 SW1 3 sw1 4 sw1 5 SW1 6 SW1 7 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 9 ON OFF OFF ON OFF OFF OFF OFF 10 OFF ON OFF ON OFF OFF OFF OFF 11 ON ON OFF ON OFF OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 16 OFF OFF OFF OFF oN OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF 19 ON ON OFF OFF ON OFF OFF OFF 20 OFF OFF ON OFF ON OFF OFF OFF 21 ON OFF ON OFF ON OFF OFF OFF 22 OFF ON ON OFF ON OFF OFF OFF 23 ON ON ON OFF ON OFF OFF OFF 24 OFF OFF OFF ON ON OFF OFF OFF 25 ON OFF OFF ON ON OFF OFF OFF 26 OFF ON OFF ON ON OFF OFF OFF 27 ON ON OFF ON ON OFF OFF OFF 28 OFF OFF ON ON ON OFF OFF OFF 29 ON OFF ON ON ON OFF OFF OFF 30 OFF ON ON ON ON OFF OFF OFF 31 ON ON ON ON ON OFF OFF OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 33 ON OFF OFF OFF OFF ON OFF OFF
25. 2 Comm 2400 N 8 1 CONFIGURE DONE This information will remain on the monitor until dome operation begins NOTE When installing a Spectra IV dome drive in a Spectra III back box for the first time a message appears When the installation is complete the dome drive will continue with a normal configuration sequence C3463M B 2 11 Operation QUICK OPERATION GUIDE Pan and Tilt Move the joystick or press the direction keys left right and up down Zoom Far To zoom far 1 Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the optical zoom limit 2 Release the button or joystick for one second 3 To continue zooming digitally press the button or turn the joystick clockwise again until you have the picture you want or reach the digital limit Zoom Wide Press the Zoom Wide button or turn the joystick counterclockwise Scanning Stop Scan Preset 96 Random Scan Preset 97 Frame Scan Preset 98 Auto Scan Preset 99 Presets Refer to the documentation supplied with THE control system Patterns Refer to the documentation supplied with the control system Zones Refer to Zones on page 40 and to the documentation supplied with the control system Alarms Refer to Alarms on page 44 Auto Flip Turn on or off in the camera menu Refer to Auto Flip on page 29 QUICK CONFIGURATION GUIDE 1 Configure preset 95 to access the main menu refer to Preset 95 Accessing Main Menu on page 11 2 Uset
26. 422 setting For control only two wires should be connected to the RX and RX connectors on the circuit board inside the back box For bidirectional control four wires should be connected to the RX RX TX and TX connectors on the circuit board inside the back box RS 485 4 Wire Setting SW2 4 should be set to OFF and SW2 5 should be set to ON if a 4 wire serial port connection is used with RS 485 NOTE This setting is most commonly used with Pelco Endura systems RS 485 2 Wire Setting SW2 4 and SW2 5 should both be set to the ON position if a 2 wire serial port connection is used with RS 485 This setting is used to allow the Spectra dome system to transmit and receive commands on the same pair of wires Only two wires should be connected to the RX and RX connectors on the circuit board inside the back box SW2 SWITCHES 6 TO 8 BAUD SETTINGS Pelco D type controllers are set for 2400 baud The default setting for the dome drive is 2400 baud If you are using a Pelco D type controller do not reset SW2 switches 1 to 3 or SW2 switches 6 to 8 Pelco P type controllers can operate at 2400 4800 and 9600 baud Set the SW2 switches 6 7 and 8 located on the base of the dome drive to the same baud as the Pelco P type controller Table A Baud Settings Switch Number SW2 6 SW2 7 SW2 8 2400 Baud default for Pelco D type control Off Off Off 4800 Baud default for Pelco P type control On Off Off 9600 Baud Off On Off
27. ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT The language for the on screen menus is selectable Available languages include English Spanish French German Italian Portuguese Russian Polish Turkish and Czech The factory default language is English To change the display language 1 Use the joystick to position the cursor beside LANGUAGE 2 Press Iris Open The cursor moves to the right beside the current selected language 3 Move the joystick up or down to view selections Press Iris Open to enter selection All on screen menus are changed to the selected language This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 19 System Information SPECTRA IV SYSTEM INFORMATION ADDITIONAL LANGUAGE SERIAL DOME DRIVE MODEL lt SYSTEM INFORMATION gt BACK BOX MEMORY lt DISPLAY SETUP gt SOFTWARE VERSION lt DOME SETTINGS gt BUILD ACK ALERT FONT VERSION RESET CAMERA comm CYCLE CAMERA POWER D ADDRESS REBOOT SYSTEM P ADDRESS 9500 MODE EXIT 32 PRESETS PROTOCOL PRESSURIZED lt ADDITIONAL gt BACK EXIT FREE MEMORY LAST RESET AZIMUTH ZERO OFFSET MOTOR ACTIVE CAMERA ACTIVE VIDEO LEVEL CAMERA MODEL LANGUAGE 1 LANGUAGE 2 LANGU LANGU LANGU LANGU LANGU LANGU LANGU AGE 3 AGE 4 5 AGE 6 AGE7 AGE8 AGE9 LANGU AGE 10 DIPSWITCH INFORMATION BACK EXIT The System Information menu displays the dome drive model
28. AMERA POWER REBOOT SYSTEM lt CAMERA gt POWER UP ACTION lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt BACK lt LINE SYNC gt EXIT lt PRESETS gt lt PATTERNS gt ZONES WINDOW BLANKING gt POWER UP ALARMS lt AUX gt TLE TEXT gt LERT gt LEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT EXIT This setting defines a specific activity scan preset pattern to be performed in the event the power to the dome is cycled The following settings are available NONE No action AUTO default The dome resumes its prior activity or direction before the power outage occurred PRESET 1 Dome goes to preset 1 PRESET 2 Dome goes to preset 2 PRESET 3 Dome goes to preset 3 PRESET 4 Dome goes to preset 4 PRESET 5 Dome goes to preset 5 PRESET 6 Dome goes to preset 6 PRESET 7 Dome goes to preset 7 PRESET 8 Dome goes to preset 8 AUTO SCAN Dome starts auto scan operation FRAME SCAN Dome starts frame scan operation RANDOM SCAN Dome starts random scan operation PATTERN 1 Dome runs pattern 1 PATTERN 2 Dome runs pattern 2 PATTERN 3 Dome runs pattern 3 PATTERN 4 Dome runs pattern 4 PATTERN 5 Dome runs pattern 5 6 7 8 PATTERN 6 Dome runs pattern 6 PATTERN 7 Dome runs pattern 7 PATTERN 8 Dome runs pattern 8 Only 27X and 35X models allow PATTERN 2 through PATTERN 8 This setting applies to Pressurized S
29. AMERA SETTINGS ALARM SETTINGS RESUME ALARM NUMBER 1 AUX 1 MODE TOGGLE SEQUENCE SECS ALARM PRIORITY DWELL TIME SECS 1 RESET DELAY SECS ALARM ACTION AUX 2 MODE TOGGLE lt ALARM SETTINGS gt ACTIVATE AUX DWELL TIME SECS 1 ALARM CONTACT TITLE TEXT ENABLE TITLE TEXT lt EDIT TITLE TEXT gt PASSWORD EDIT THE PASSWORD ENABLE PASSWORD OFF 1234567890 OK TIME BASE INTERNAL CLOCK lt EDIT PASSWORD gt ABCDEFGHIJ CANCEL TIME FORMAT 12 HOUR 12 00 UVWKXYZ BACKSPACE DATE FORMAT MM DD YYYY abcdefghij SPACE SET DATE 00 00 0000 kImnoparst DAYLIGHT SAVINGS OFF uvwxyz amp 14 C3463M B 2 11 27X LowLight Day Night Menu Tree SYSTEM INFORMATION SERIAL XXXXXXXXXXXXXX DOME DRIVE MODEL XX XXXX BACK BOX MEMORY AVAILABLE SOFTWARE VERSION BUILD FONT VERSION XXX COMM XXXXXXXXXX D ADDRESS 1 P ADDRESS 2 9500 MODE OFF 32 PRESETS OFF PROTOCOL C PRESSURIZED lt ADDITIONAL gt ADDITIONAL FREE MEMORY LAST RESET AZIMUTH ZERO OFFSET MOTOR ACTIVE CAMERA ACTIVE VIDEO LEVEL NORMAL CAMERA MODEL XXXX XXXX LANGUAGE 1 ENGLISH LANGUAGE 10 lt DIPSWITCH INFORMATION gt ITALIANO X XX CAMERA TYPE OF LIGHTING T PICTURE MODE NORMAL AUTO FOCUS ON SURE FOCUS OFF PT FOCUS LOCK OFF ZOOM LIMIT 200 SPEED LOW LIGHT LIMIT IR CUT FILTER AUTO IR LEVEL LOW LIGHT FOCUS ADVANCED SETTINGS PATTERNS PATTERN NUMBER 1 PROGRAM PATTERN
30. AUX 2 d Press Iris Open to enter selection NOTE The AUX 1 AUX will stop when all the alarms assigned to it have cleared If the AUX1 AUX is set up as momentary then it will be activated each time a new alarm is activated Set the alarm contact a the joystick to position the cursor beside ALARM CONTACT b Press Iris Open The cursor moves to the right c the joystick up or down to view the following available selections N O default Normally open N C Normally closed d Press Iris Open to enter selection NOTE The alarm contact feature is functional and available for 23X models only if the dome drive is installed in a Spectra III SE Spectra IV SE back box To edit the alarm schedule The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on page 53 with the following exceptions In the Edit Schedule menu the event type cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For instructions on changing the features in the Edit Schedule menu refer to Edit Event on page 54 45 AUX SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT An auxiliary output configured to trigg An AUX 1 comman AUX 1 can be conn An AUX 2 comman The following are TOGGLE default LATCHING Must receive an AUX ON AUX O
31. BEL 2 SECS ZOOM 2 SECS AZIMUTH ELEVATION 2 SECS DIRECTION ALARM MESSAGE DATE TIME ON EVENT LABEL 2 SECS lt LABEL POSITIONS gt RESTORE FACTORY DEFAULTS ZONE LABEL PRESET LABEL ALARM EVENT ALERT MESSAGE TITLE TEXT SAVE AND EXIT CANCEL HELP NE XX XX XXX X MM DD YYYY 12 00 00 AM AUTO TRACKING AUTO TRACKING DISPLAY SETUP SENSITIVITY START TIME Z00M LOST ACTION RETURN SET WINDOWS WINDOW NUMBER EDIT WINDOW LOCATION EDIT WINDOW Z00M EDIT SCHEDULE ENABLE WINDOW REVERSE CLEAR WINDOW ALERT CURRENT READING REPEAT CONSTANT TEMPERATURE ACK ACTION ALWAYS ON DEWPOINT ACTIVATE AUX NO PRESURE CLEAR CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL WINDOW BLANKING CLEAR ALL EVENTS RESTORE FACTORY DEFAULTS PASSWORD ENABLE PASSWORD OFF EDIT PASSWORD CURRENT READING REFRESH RESET ALERT This setting applies to Pressurized Spectra IV dome systems only Spectra IV systems that are not pressurized will not display this menu item NOTE The BACK and EXIT options do not appear in these menus due to space limitations See the individual menus in this document for complete configurations C3463M B 2 11 15 DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX
32. CM9700 Series matrix Digital Light Processing DLP displays except lamp and color wheel The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Intelli M elDC controllers One year Video cassette recorders VCRs except video heads Video heads will be covered for a period of six months e Six months All pan and tilts scanners or preset lenses used in continuous motion applications preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides th
33. DETECTION gt a RESET CAMERA PATTERNS EDIT SCHEDULE EXIT ZONES CYCLE CAMERA POWER CLEAR gt WINDOW BLANKING gt CLEAR CAMERA SETTINGS REBOOT SYSTEM ALARMS EXIT lt AUX gt BACK lt TITLE TEXT gt i REFERENCE INFORMATION ALERT lt CLEAR gt ELEVATION lt PASSWORD gt 20 RATIO lt CLOCK gt CUSTOM CAMERA SETTINGS lt EVENT gt BACK EXIT Enable Motion Detection The following are the settings for motion detection OFF default Motion detection is turned off disabled ON Motion detection is turned on enabled NOTE Motion detection does not work if the shutter speed is set at less than 1 60 of a second Edit Detection Areas Four motion detection areas can be defined for a preset Use the following steps to edit motion detection areas 1 Edit detection areas 1 2 3 or 4 a the joystick to position the cursor beside EDIT DETECTION AREAS b Press Iris Open The EDIT DETECTION AREAS configuration window appears EDIT DETECTION AREAS DETECTION AREA 1 LOCATION 0 SENSITIVITY MEDIUM DETECTION AREA 2 LOCATION 0 SENSITIVITY MEDIUM DETECTION AREA 3 LOCATION 0 SENSITIVITY MEDIUM DETECTION AREA 4 LOCATION 0 SENSITIVITY MEDIUM BACK EXIT Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1 2 3 or 4 d Press Iris Open The cursor moves to the right next to the number 0 e Move the joystick up A blue
34. EDIT EVENT gt EVENT OCCURS kimnopqrst DAYLIGHT SAVINGS OFF lt CLEAR EVENT gt SUNDAY uvwxyz amp lt LIST EVENT gt MONDAY TUESDAY HOLIDAY WEDNESDAY lt EDIT HOLIDAY gt THURSDAY lt CLEAR HOLIDAY gt FRIDAY lt LIST HOLIDAYS gt SATURDAY ON HOLIDAY SKIP HOLIDAYS BACK EXIT EVENT TYPE PRESET 1 NUMBER REFERENCE INFORMATION 16 C3463M B 2 11 35X LowLight Day Night Menu Tree SPECTRA IV LANGUAGE ENGLISH lt SYSTEM INFORMATION gt DISPLAY SETUP DOME SETTINGS ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SYSTEM INFORMATION DISPLAY SETUP SERIAL XXXXXXXXXXXXXX PRESET LABEL 2 SECS DOME DRIVE MODEL XX XXXX ZONE LABEL 2 SECS BACK BOX MEMORY AVAILABLE ZOOM 2 SECS SOFTWARE VERSION AZIMUTH ELEVATION 2 SECS BUILD DIRECTION FONT VERSION ALARM MESSAGE COMM DATE TIME N D ADDRESS 1 EVENT LABEL 2 SECS P ADDRESS 2 9500 MODE OFF lt LABEL POSITIONS gt 32 PRESETS OFF RESTORE FACTORY DEFAULTS PROTOCOL C PRESSURIZED DIPSWITCH INFORMATION LABEL POSITION sw swa ZONE LABEL ADDITIONAL LABEL lt ADDITIONAL gt 12345678 1234567890 1 ALARM EVENT FREE MEMORY D ADDRESS 1 ALERT MESSAGE LAST RESET P ADDRESS 2 TITLE TEXT AZIMUTH ZERO OFFSET SW21 32PRESETS OFF MOTOR ACTIVE SW22 CM9500 MODE OFF SAVE AND EXIT CAMERA ACTIVE SW23 COAXSPIV CANCEL VIDEO LEVEL NORMAL SW2 4 5 RS422 lt gt HELP CAMERA
35. EL ZONE LABEL SYSTEM INFORMATION M dee PRESET LABEL DISPLAY SETUP gt EVENT AZIMUTH ELEVATION DOME SETTINGS ALERT MESSAGE DIRECTION TITLE TEXT ACK ALERT ALARM MESSAGE lt gt RESET CAMERA DATE TIME CYCLE CAMERA POWER EVENT LABEL SAVE AND EXI REBOOT SYSTEM lt LABEL POSITIONS gt CANCEL RESTORE FACTORY DEFAULTS HELP BACK EXIT NE XX XX XXX X MM DD YYYY 12 00 00 AM Labels can be placed anywhere on the monitor This feature allows you to customize the appearance of your monitor screen The following labels are not set at fixed positions ZONE LABEL PRESET LABEL ALARM ZOOM RATIO AZIMUTH ELEVATION XX XX DIRECTION NE ALERT MESSAGE TITLE TEXT EVENT LABEL DATE TIME To set a label position 1 Use the joystick to position the cursor beside a label 2 Press Iris Open 3 Usethe joystick to move the label up down left or right 4 Press Iris Open 5 Repeat steps 1 to 4 to position other labels 6 Position the cursor next to Save and Exit Press Iris Open to save settings and exit the menu This setting applies to Pressurized Spectra dome systems only t Azimuth is the pan angle from zero to 359 degrees Elevation is the tilt position from zero horizon to 90 degrees The alert message is the warning displayed on the monitor if pressure temperature or dew point inside the dome reach unacceptable levels 22 C3463M B 2 1
36. FF ON ON ON OFF ON ON 222 OFF ON ON ON ON OFF ON ON 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 231 ON ON ON OFF OFF ON ON ON 232 OFF OFF OFF ON OFF ON ON ON 233 ON OFF OFF ON OFF ON ON ON 234 OFF ON OFF ON OFF ON ON ON 235 ON ON OFF ON OFF ON ON ON 236 OFF OFF ON ON OFF ON ON ON 237 ON OFF ON ON OFF ON ON ON 238 OFF ON ON ON OFF ON ON ON 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 243 ON ON OFF OFF ON ON ON ON 244 OFF OFF ON OFF ON ON ON ON 245 ON OFF ON OFF ON ON ON ON 69 70 Table G Switch Settings for SW1 Pelco D Type Control 6 of 6 SWITCH SETTING ADDRESS SWI 1 2 SW1 3 SWI 4 SWI 5 SW1 6 SW1 7 sw1 8 247 ON ON ON OFF ON ON ON ON 248 OFF OFF OFF ON ON ON ON ON 249 ON OFF OFF ON ON ON ON ON 250 OFF ON OFF ON ON ON ON ON 251 ON ON OFF ON ON ON ON ON 252 OFF OFF ON ON ON ON ON ON 253 ON OFF ON ON ON ON ON ON 254 OFF ON ON ON ON ON ON ON C3463M B 2 11 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the d
37. FF command from the controller to turn the auxiliary output on off DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT er from an alarm or from a controller he available AUX mode settings Changes the state of the auxiliary output every time an AUX command is received from the controller AUX 1 MODE DWELL TIME SECS AUX 2 MODE DWELL TIME SECS lt EDIT SCHEDULE gt BACK EXIT TOGGLE 1 TOGGLE 1 d from the controller will place a ground at the output of AUX 2 to operate the device that is connected to it is a configurable signal from the dome back box that can trigger another device to operate An auxiliary output can be d from the controller will activate the relay in the dome and operate the device that is connected to the relay The output of ected to the alarm input of a system switch to activate automatic monitor switching and recording MOMENTARY An AUX ON command from the controller turns the auxiliary output on for the configured DWELL TIME The auxiliary output will automatically turn EDIT SCHED off when the dwell time is finished ULE The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on
38. IR illuminator the low light focus feature of the camera can be tuned to correspond to the setting of the illuminator There are three low light focus settings OFF default Low light focus is not activated 850NM Low light focus is tuned to 850 nm nanometers 950NM Low light focus is tuned to 950 nm C3463M B 2 11 25 ADVANCED CAMERA SETTINGS SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt TLE TEXT gt LERT gt LEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT CAMERA TYPE OF LIGHTING PICTURE MODE AUTO FOCUS SURE FOCUS PT FOCUS LOCK ZOOM LIMIT ZOOM SPEED LOW LIGHT LIMIT IR CUT FILTER AUTO IR LEVEL LOW LIGHT FOCUS lt ADVANCED SETTINGS gt BACK EXIT ADVANCED SETTINGS SHUTTER SPEED AGC LIMIT AUTO IRIS UTO IRIS LEVEL UTO IRIS PEAK AUTO SHARPNESS HARPNESS LEVEL AUTO WHITE BALANCE R GAIN B GAIN BACKLIGHT COMP IMAGE STABILIZER DE DYNAMIC RANGE LOW LUX NOISE REDUCTION VIDEO LEVEL FIELD ALIGN LOW LIGHT SHARPNESS MINIMUM FOCUS DISTANCE SHUTTER SPEED Shutter speed is the duration of the electronic shutter You can configur
39. Iris Open to select the week Use the joystick to position the cursor beside DAY Press Iris Open Scroll through the options until the desired day of the week appears Press Iris Open to select the day CLEAR HOLIDAY To clear a holiday 1 Use the joystick to position the cursor beside CLEAR HOLIDAY 2 Press Iris Open 3 Follow the directions displayed on the monitor LIST HOLIDAYS To list events 1 Use the joystick to position the cursor beside LIST HOLIDAYS 2 Press Iris Open 3 All configured holidays will be listed C3463M B 2 11 SCHEDULED EVENTS Use this page to record scheduled events EVENT NUMBER EVENT TYPE LABEL TIME OCCURS Example 1 Preset Weekend 11 00 AM Sat Sun Description Camera focuses on gate on weekends when the office is closed HOLIDAY Skips Holidays C3463M B 2 11 57 Reset Cycle Power Reboot LANGUAGE ENGLISH lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT RESET CAMERA Use this function to reset all camera settings to factory default parameters CYCLE CAMERA POWER If the camera is not operating or if you lose camera control cycle camera power Cycling camera power resets the camera but does not change any saved camera settings REBOOT SYSTEM Reboot the system if it is not operating if there
40. L LANGUAGE 1 LANGUAGE 10 DIPSWITCH INFORMATION CAMERA TYPE OF LIGHTING AUTO FOCUS PT FOCUS LOCK IR CUT FILTER AUTO IR LEVEL ADVANCED SETTINGS ZONES ZONE NUMBER ENGLISH X XX ITALIANO 1 70NE NOT DEFINED EDIT ZONE LABEL EDIT ZONE ZONE ENABLED ZONE BLANKING CLEAR ZONE ALERT REPEAT ACK ACTION ACTIVATE AUX CURRENT READING RESET ALERT CONSTANT ALWAYS ON NO D ADDRESS 1 P ADDRESS 2 SW21 32PRESETS OFF SW22 CM9500 MODE OFF 23 COAXSPIV COMM SW2 4 5 RS422 lt gt 510 2 6 8 COMM 2400 N 8 1 54 29 UTC SOURCE COAX SW210 TERM OFF PRESS IRIS OPEN TO CONTINUE ADVANCED SETTINGS SHUTTER SPEED AGC LIMIT AUTO IRIS AUTO IRIS LEVEL AUTO IRIS PEAK AUTO SHARPNESS SHARPNESS LEVEL AUTO WHITE BALANCE R GAIN B GAIN BACKLIGHT COMP VIDEO LEVEL FIELD ALIGN WINDOW BLANKING STYLE BLANK ALL ABOVE BLANK ALL BELOW lt SET WINDOWS gt CURRENT READING TEMPERATURE DEWPOINT PRESSURE REFRESH DIPSWITCH INFORMATION 12345678 1234567890 2 1 MOTION AUTO FLIP PROPORTIONAL PAN PARK TIME MINUTES PARK ACTION SCAN SPEED DEG S PRESET FREEZE FRAME LIMIT STOPS lt SET MANUAL STOPS gt lt CLEAR MANUAL STOPS gt lt SET SCAN STOPS gt lt CLEAR SCAN STOPS gt lt SET AZIMUTH ZERO gt lt CLEAR AZIMUTH ZERO gt SET WINDOWS WINDOW NUMBER lt EDIT WINDOW LOCATION gt lt EDIT WINDOW ZOOM gt ENABLE WINDOW REVERSE
41. NABLED ENABLE WINDOW REFERENCE INFO 0 ZONE BLANKING REVERSE PATTERN USAGE 100 CLEAR ZONE CLEAR WINDOW REMAINING ALERT CURRENT READING CLEAR PASSWORD REPEAT CONSTANT TEMPERATURE CLEAR ALL ZONES ENABLE PASSWORD OFF ACK ACTION ALWAYS ON DEWPOINT CLEAR ALL PRESETS EDIT PASSWORD ACTIVATE AUX NO PRESSURE CLEAR ALL PATTERNS CURRENT READING REFRESH CLEAR ALL WINDOW BLANKING RESET ALERT CLEAR ALL EVENTS RESTORE FACTORY DEFAULTS This setting applies to Pressurized Spectra IV dome systems only Spectra IV systems that are not pressurized will not display this menu item NOTE The BACK and EXIT options do not appear in the menus due to space limitations See the individual menus in this document for complete configurations C3463M B 2 11 17 DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt POWER UP POWER UP ACTION AUTO LINE SYNC PRESETS MOTION DETECTION EDIT DETECTION AREAS LINE SYNC ON PRESET NUMBER MOTION DETECTION ENABLED DETECTION AREA 1 LINE SYNC PHASE 0 PRESET DEFINED lt EDIT DETECTION AREAS gt LOCATION 0 lt EDIT PRESET LABEL gt ACTIVATE AUX SENSITIVITY MEDIUM lt EDIT PRESET SCENE gt AUX TIME SECS DETECTION AREA 2 l
42. OFF ON 186 OFF ON OFF ON ON ON OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF OFF ON ON ON ON OFF ON 189 ON OFF ON ON ON ON OFF ON 190 OFF ON ON ON ON ON OFF ON 191 ON ON ON ON ON ON OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 193 ON OFF OFF OFF OFF OFF ON ON 194 OFF ON OFF OFF OFF OFF ON ON 195 ON ON OFF OFF OFF OFF ON ON 196 OFF OFF ON OFF OFF OFF ON ON C3463M B 2 11 C3463M B 2 11 Table G Switch Settings for SW1 Pelco D Type Control 5 of 6 SPEAN SWITCH SETTING ADDRESS SW1 2 SW1 3 SWI 4 SWI 5 SW1 6 1 7 sw1 8 197 ON OFF ON OFF OFF OFF ON ON 198 OFF ON ON OFF OFF OFF ON ON 199 ON ON ON OFF OFF OFF ON ON 200 OFF OFF OFF ON OFF OFF ON ON 201 ON OFF OFF ON OFF OFF ON ON 202 OFF ON OFF ON OFF OFF ON ON 203 ON ON OFF ON OFF OFF ON ON 204 OFF OFF ON ON OFF OFF ON ON 205 ON OFF ON ON OFF OFF ON ON 206 OFF ON ON ON OFF OFF ON ON 207 ON ON ON ON OFF OFF ON ON 208 OFF OFF OFF OFF ON OFF ON ON 209 ON OFF OFF ON OFF ON ON 210 OFF ON OFF ON OFF ON ON 211 ON ON OFF OFF ON OFF ON ON 212 OFF OFF ON OFF ON OFF ON ON 213 ON OFF ON OFF ON OFF ON ON 214 OFF ON ON OFF ON OFF ON ON 215 ON ON ON OFF ON OFF ON ON 216 OFF OFF OFF ON ON OFF ON ON 217 ON OFF OFF ON ON OFF ON ON 218 OFF ON OFF ON ON OFF ON ON 219 ON ON OFF ON ON OFF ON ON 220 OFF OFF ON ON ON OFF ON ON 221 ON O
43. OFF ON ON OFF 105 ON OFF OFF ON OFF ON ON OFF 106 OFF ON OFF ON OFF ON ON OFF 107 ON ON OFF ON OFF ON ON OFF 108 OFF OFF ON ON OFF ON ON OFF 109 ON OFF ON ON OFF ON ON OFF 110 OFF ON ON ON OFF ON ON OFF 111 ON ON ON ON OFF ON ON OFF 112 OFF OFF OFF OFF ON ON ON OFF 113 ON OFF OFF OFF ON ON ON OFF 114 OFF ON OFF OFF ON ON ON OFF 115 ON ON OFF OFF ON ON ON OFF 116 OFF OFF ON OFF ON ON ON OFF 117 ON OFF ON OFF ON ON ON OFF 118 OFF ON ON OFF ON ON ON OFF 119 ON ON ON OFF ON ON ON OFF 120 OFF OFF OFF ON ON ON ON OFF 121 ON OFF OFF ON ON ON ON OFF 122 OFF ON OFF ON ON ON ON OFF 123 ON ON OFF ON ON ON ON OFF 124 OFF OFF ON ON ON ON ON OFF 125 ON OFF ON ON ON ON ON OFF 126 OFF ON ON ON ON ON ON OFF 127 ON ON ON ON ON ON ON OFF 128 OFF OFF OFF OFF OFF OFF OFF ON 129 ON OFF OFF OFF OFF OFF OFF ON 130 OFF ON OFF OFF OFF OFF OFF ON 131 ON ON OFF OFF OFF OFF OFF ON 132 OFF OFF ON OFF OFF OFF OFF ON 133 ON OFF ON OFF OFF OFF OFF ON 134 OFF ON ON OFF OFF OFF OFF ON 135 ON ON ON OFF OFF OFF OFF ON 136 OFF OFF OFF ON OFF OFF OFF ON 137 ON OFF OFF ON OFF OFF OFF ON 138 OFF ON OFF ON OFF OFF OFF ON 139 ON ON OFF ON OFF OFF OFF ON 140 OFF OFF ON ON OFF OFF OFF ON 141 ON OFF ON ON OFF OFF OFF ON 142 OFF ON ON ON OFF OFF OFF ON 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OFF OFF ON 147 ON ON OFF OFF ON OFF OFF ON 67 68 Table G Switch Sett
44. ON OFF ON OFF OFF OFF ON OFF 70 OFF ON ON OFF OFF OFF ON OFF 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OFF 79 ON ON ON ON OFF OFF ON OFF 80 OFF OFF OFF OFF ON OFF ON OFF 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF ON OFF 83 ON ON OFF OFF ON OFF ON OFF 84 OFF OFF ON OFF ON OFF ON OFF 85 ON OFF ON OFF ON OFF ON OFF 86 OFF ON ON OFF ON OFF ON OFF 87 ON ON ON OFF ON OFF ON OFF 88 OFF OFF OFF ON ON OFF ON OFF 89 ON OFF OFF ON ON OFF ON OFF 90 OFF ON OFF ON ON OFF ON OFF 91 ON ON OFF ON ON OFF ON OFF 92 OFF OFF ON ON ON OFF ON OFF 93 ON OFF ON ON ON OFF ON OFF 94 OFF ON ON ON ON OFF ON OFF 95 ON ON ON ON ON OFF ON OFF 96 OFF OFF OFF OFF OFF ON ON OFF 97 ON OFF OFF OFF OFF ON ON OFF 98 OFF ON OFF OFF OFF ON ON OFF C3463M B 2 11 C3463M B 2 11 Table G Switch Settings for SW1 Pelco D Type Control 3 of 6 SWITCH SETTING ADDRESS SW1 2 SW1 3 SWI 4 SWI 5 SW1 6 sw1 7 sw1 8 99 ON ON OFF OFF OFF ON ON OFF 100 OFF OFF ON OFF OFF ON ON OFF 101 ON OFF ON OFF OFF ON ON OFF 102 OFF ON ON OFF OFF ON ON OFF 103 ON ON ON OFF OFF ON ON OFF 104 OFF OFF OFF ON
45. PERS 32 LOSE ACTON a 32 ortho Essi caste rae tete yr bau NAM 32 POW GT AAE caste 33 PowerU p AGUOR cs ha Lodel gt eot edu e b Eu 33 SVG eer teres AS nA at C M RM 34 Presets MERERETUR 34 SEC bett aseo canada cided det 37 Edit Schedule a cns tas oe a ced ideo lee Pd Salade dum 38 Patterss exeo esos dabis Mura pedit DAE rio cre Rab ce ted ME 39 ZOTBS ane Medea a ea b A Bald tem teta Me en ee er nce MR Ete als 40 Window Blanking zc curte ax EE QURE MUS 41 Edit Schedule 3537 iere ELT su te tete ay ce nm aulas 42 nce ta cA c ttd npe dud m k s NU n a ARM Socr du UM 42 CIGAR WIBODW 42 BlankAlli Above Blank 5 55 22 1 oett Ree hank c Dat dead lla 43 ana us RE ea up Saa aa UK UBER TUER AERE RN ya NEC 44 nic cU 46 Edit Schede e cte n t eir dope f 46 BIN METTE 47 Ghats e sree M e ce kasqa En d DAT tea
46. R ALL WINDOW BLANKING CLEAR ALL EVENTS RESTORE FACTORY DEFAULTS BACK EXIT Use this setting to clear user defined settings or return the dome to factory default settings The following are the available settings ALL ZONES Clears all zones To clear a single zone refer to Zones on page 40 ALL PRESETS Clears all presets To clear a single preset refer to Presets on page 34 ALL PATTERNS Clears all patterns To clear a single pattern refer to Patterns on page 39 ALL WINDOW BLANKING Clears all blanked windows To clear a single blanked window refer to Window Blanking on page 41 CLEAR ALL EVENTS Clears all events To clear a single event refer to Event on page 53 RESTORE FACTORY DEFAULTS Restores all camera settings to factory default settings PASSWORD SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT PASSWORD ENABLE PASSWORD lt EDIT PASSWORD gt BACK EXIT EDIT THE PASSWORD 1234567890 OK ABCDEFGHIJ CANCEL KLMNOPORST UVWXYZ BACKSPACE abcdefghij SPACE
47. To set the clock do the following 1 Use the joystick to position the cursor beside TIME BASE Press Iris Open The following are the settings for time base POWER LINE This is the most accurate time base and is the preferred selection in areas with a stable power line frequency INTERNAL CLOCK The internal clock should be used in areas where the power line frequency is not accurate a Move the joystick up or down to view the selections b Press Iris Open to select INTERNAL CLOCK or POWER LINE Use the joystick to position the cursor beside TIME FORMAT Press Iris Open Move the joystick up or down to view the selections Select 12 HOUR or 24 HOUR and then press Iris Open to confirm the time format Use the joystick to position the cursor beside SET TIME Press Iris Open Scroll through the hours until the desired time appears Use the joystick to move the cursor to the right Scroll through the minutes until the desired time appears Press Iris Open to select the time Use the joystick to position the cursor beside DATE FORMAT Press Iris Open Move the joystick up or down to select MM DD YYYY or DD MM YYYY Press Iris Open to confirm the date format Use the joystick to position the cursor beside SET DATE Press Iris Open Scroll through the days months and years until the desired number appears Press Iris Open to select the date Use the joystick to position the cursor beside DAYLIGHT SAVINGS Press Iris Open The fol
48. UTO TRACKING SENSITIVITY lt DISPLAY SETUP gt POWER UP gt START TIME lt DOME SETTINGS gt INE SYNC gt 700 ALERT RESETS gt LOST ACTION RESET CAMERA PATTERNS gt RETURN CYCLE CAMERA POWER REBOOT SYSTEM EXIT LARMS gt UX gt TLE TEXT gt LERT gt LEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT AUTO TRACKING Auto tracking allows the camera to automatically pan tilt and zoom to track objects of interest people cars and so forth when motion is detected in a scene without requiring an operator to manually control the camera s PTZ movements There are two settings ON Auto tracking is enabled OFF default Auto tracking is disabled NOTE If the auto tracking setting is OFF all other settings in the Auto Tracking menu are disabled C3463M B 2 11 31 32 DISPLAY SETUP When display setup is enabled you are notified that the camera detects motion in a scene There are two settings ON default Display setup is enabled and a transparent blue rectangle appears in the area of the scene where motion has been detected OFF Display setup is disabled SENSITIVITY Sensitivity adjusts the camera s sensitivity to motion thereby adjusting the number of moving objects that will be tracked automatically There are two settings HIGH default Sensitivity is increased and most moving objects regardless of size will be detected and tracked LOW Sensitivity is decr
49. WINDOWS gt ENABLE WINDOW RESET CAMERA REVERSE CYCLE CAMERA POWER SWINGOWBUANKINGS BACK CLEAR WINDOW REBOOT SYSTEM lt ALARMS gt EXIT BACK EXIT lt AUX gt EXIT lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT Window blanking allows a user to configure the four sided areas that cannot be viewed by the operator of the dome system A blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide The 23X models have four user defined windows blank available The 27X and 35X models have eight available user defined window blanks Spectra IV dome systems have two styles of window blanking Gray and Smear If the style is set to Gray the blanked area is covered with a solid gray window If Smear is selected images behind the window will be noticeable but not distinguishable To set a window blanking area 1 Use the joystick to position the cursor beside WINDOW BLANKING Press Iris Open The WINDOW BLANKING menu appears on the screen 2 Move the joystick to position the cursor beside SET WINDOWS Press Iris Open to enter 3 Position the cursor beside WINDOW NUMBER Press Iris Open The cursor moves to the right 4 Move the joystick up or down to view selections Press Iris Open to enter selection 5 Use the joystick to position the cursor beside EDIT WINDOW LOCATION Press Iris Open and then follow the instructio
50. a RETIRER De 28 nate a Mactan otc bot dece metr t cde s AE rode 28 C3463M B 2 11 3 T EU 28 kow Eight Duy 29 Minimu FOCUS DISEdTEern s 25 E Rab oet Dao ERN fut tid 29 Motion Settligs io eere E vet dad Yo et ae ae dea a ee ee ake is 29 AUTO ato SG Sn Aan et ue ot 29 Proportional Palio sss certet mere upa u aa INI EN Some EU UM Sek Eames ena 29 vob Q aun as Eni Le foal ache Ma DO AN RA Se MY uC eie Mna ete A pets 30 SCAN SPEC ty ate ae ese eek has a BR th ee cade 30 isis za Bs 4 s TERRE DR ETE w amu Sadat tap bar tall tiki aot TETTE 30 Limib STOPS o eee RS hale eel 30 Pd DR qa 31 AUTO TAGKING ete 31 31 yn aca asam ena Sam Se Ae tit ca b M a au ee NU Oe cm I 32 SENSITIVITY uz erect ee eru RE A 32 WME nd accents et ne tome S ole ich E teme TAE AAT 32
51. anual joystick pan operation stops when a limit stop is reached SCAN The dome reverses direction during random frame or auto scanning when a limit stop is reached C3463M B 2 11 To set manual scan stops 1 Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS 2 Press Iris Open 3 Follow the directions displayed on the monitor NOTE In order for the manual or scan stops to work the LIMIT STOPS option must be ON To clear manual or scan stops 1 Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN STOPS 2 Press Iris Open 3 Follow the directions displayed on the monitor AZIMUTH ZERO Azimuth is the pan angle from zero to 359 degrees Azimuth zero is the pan position you specify to be the zero degree point Azimuth zero is normally set to magnetic north Once set azimuth and compass readings are based on the set Azimuth Zero point To configure azimuth zero 1 Use the joystick to position the cursor beside SET AZIMUTH ZERO 2 Press Iris Open 3 Follow the directions displayed on the monitor To clear azimuth zero 1 Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO 2 Press Iris Open 3 Follow the directions displayed on the monitor AUTO TRACKING Applies to 27X and 35X models only SPECTRA IV DOME SETTINGS AUTO TRACKING LANGUAGE CAMERA AUTO TRACKING lt MOTION gt DISPLAY SETUP lt SYSTEM INFORMATION gt lt A
52. ate of shipment Exceptions to this warranty are as noted below Five years Fiber optic products Unshielded Twisted Pair UTP transmission products CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and C3651H 2X camera models years Pelco designed fixed network cameras and network dome cameras with Sarix technology Pelco branded fixed camera models CCC1390H Series C10DN Series C10CH Series and IP3701H Series EH1500 Series enclosures Spectra IV products including Spectra IV IP Camclosure Series IS ICS IP integrated camera systems DX Series digital video recorders except DX9000 Series which is covered for a period of one year DVR5100 Series digital video recorders Digital Sentry Series hardware products DVX Series digital video recorders and NVR300 Series network video recorders Endura Series distributed network based video products Genex Series products multiplexers server and keyboard PMCL200 300 400 Series LCD monitors PMCL5xx Series FHD monitors Two years Standard varifocal fixed focal and motorized zoom lenses DF5 DF8 Series fixed dome products Legacy Series integrated positioning systems Spectra Spectra Mini Spectra Mini IP Esprit ExSite and PS20 scanners including when used in continuous motion applications Esprit Ti and TI2500 Series thermal imaging products Esprit WW5700 Series window wiper excluding wiper blades CM6700 CM6800
53. by Schneider Electric Spectra IV SL and Spectra IV SE Series 23X 27X and 35X Dome Drives C3463M B 2 11 Contents Description PR 6 i t sno 7 SWITCITSettln Seren AM t a anan E UTERE 7 SWI Receiver da dr Abe LO a 7 SW2 Switch 1 AD 32 Preset System us eu ee x rue Soca YVE AD NOR QNS 7 s Peces tue ew eor dt o Mem s 7 SW2 Switch 3 Control System 2a Po Ae Sues wee Rares DON MEME 7 SW2 Switches 4and 5 Seriali Port Settings he waded Meda ccs chad Linea ceed 8 SW2Switches 6 to 8 Bald Settinigs lt ev nk ay ele QU e eti 8 Dome Drives cle pu am nota 9 Operation METTE 10 Guick Operation Guide d ur titm e C EU eu S ER Eo ad to ota tue ter ote Mande Saya ea eraut 10 Quick Configuration Guide EE dae ds 10 Preset ab Accessing Menu 2 c t etate e wv a qa 11 700 12 T EE UII Gt RD RP YEN RUNE PM CRANE TOES 11 BD200A KBD300A Direct Made Only
54. cally started with park power up event and alarm functions This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 39 ZONES SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt ZONE NUMBER ZONE NOT DEFINED EDIT ZONE LABEL EDIT ZONE ZONE ENABLED ZONE BLANKING CLEAR ZONE EXIT ALARMS BACK lt AUX gt EXIT lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT zone is a pan area defined by a left and right limit on the 360 degree pan plane Spectra IV dome systems are capable of eight zones each with a 20 character label To configure a zone 1 Use the joystick to position the cursor beside ZONE NUMBER Press Iris Open and the cursor moves to the right 2 Move the joystick up or down to view selections Press Iris Open to enter selection 3 Use the joystick to position the cursor beside EDIT ZONE 4 Press Iris Open The Zone configuration window appears 5 Follow the directions displayed on the monitor After the left and right limit stops are set the Zones menu reappears with the ZONE ENABLED opti
55. cus capability in low light scenes depending on the typical distance between the camera and objects in the scene There are two settings 30 CM default Improves focus for scenes in which the camera is typically focusing on objects at close range less than 3 meters 3 M Improves focus for scenes in which the camera is typically focusing on objects at a distance of 3 meters or more MOTION SETTINGS LANGUAGE lt CAMERA gt AUTO FLIP PROPORTIONAL PAN SYSTEM INFORMATION lt MOTION gt lt DISPLAY SETUP gt AUTO TRAL KINGS PRAAK ACION O S lt DOME SETTINGS gt OWER UP gt SCAN SPEED DEG S ACK ALERT NE SYNC gt PRESET FREEZE FRAME RESETS gt CAMERA PATTERNS RSET MANUAL STOPS lt gt OWER lt CLEAR MANUAL STOPS gt lt SET SCAN STOPS gt EXIT LARMS gt lt CLEAR SCAN STOPS gt UX gt lt SET AZIMUTH ZERO gt TLE TEXT gt lt CLEAR AZIMUTH ZERO gt LERT gt BACK PASSWORD EXIT gt OCK gt REFERENCE INFORMATION EVENT MANUAL LIMITS SET SCAN LIMITS SET BACK EXIT AUTO FLIP When the camera tilts downward and goes just beyond the vertical position the dome rotates 180 degrees When the dome rotates flips the camera starts moving upward as long as you continue to hold the joystick in the down position Once you let go of the joystick after the dome rotates joystick control returns to normal operation The auto flip feature is useful for following a person who passes directly beneath the do
56. de OFF The sharpness of the picture is set manually by configuring the sharpness level Sharpness level settings range from 0 to 63 AUTO WHITE BALANCE This feature automatically processes the viewed image to retain color balance over a color temperature range The default setting for auto white balance is ON R GAIN Adjusts the picture output in the red range As you change the value you will see the color change on your monitor B GAIN Adjusts the picture output in the blue range As you change the value you will see the color change on your monitor BACKLIGHT COMPENSATION If a bright backlight is present the subjects in the picture may appear dark or as a silhouette Backlight compensation BLC enhances objects in the center of the picture The dome uses the center of the picture to adjust the iris If there is a bright light source outside of this area it will wash out to white The camera will adjust the iris so that the object in the sensitive area is properly exposed There are two backlight compensation settings OFF default Backlight compensation is not activated ON Backlight compensation is activated If backlight compensation is ON decrease the auto iris level setting and adjust the auto IR level to a darker setting Refer to Auto Iris Level on page 26 and Auto IR Level section on page 25 ELECTRONIC IMAGE STABILIZATION Applies to 35X models only Electronic image stabilization is a feature of the camera tha
57. e Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment number sales order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS To expedite parts returned for repair or credit please call Pelco at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair and designated return location All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Green materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that m
58. e alert message is displayed every 60 minutes for a 15 second duration until acknowledged OFF The alert message is disabled and will not be displayed ACK ACTION Set ACK ACTION to configure the frequency at which an alert message is displayed after the alert condition has been acknowledged The following settings are available ALWAYS ON The alert message is displayed until alert conditions are cleared OFF 8 HRS The alert message is turned off for 8 hours Message returns after 8 hours if the alert condition persists OFF 24 HRS The alert message is turned off for 24 hours Message returns after 24 hours if the alert condition persists OFF 48 HRS The alert message is turned off for 48 hours Message returns after 48 hours if the alert condition persists C3463M B 2 11 ACTIVATE AUX This setting activates an auxiliary when an alert condition exists Settings include the following options NONE default Not activated 1 An alert condition will close AUX 1 2 An alert condition will close AUX 2 CURRENT READING The Current Reading menu displays the existing status of temperature pressure and dew point inside the dome system An arrow displayed to the left of a menu item denotes that an alert condition exists CURRENT READING TEMPERATURE DEWPOINT PRESSURE REFRESH BACK EXIT An up arrow indicates the reading 1 over the threshold A down arrow indicates the reading is below the threshold The high temperatu
59. e systems can operate with coaxial control systems from many manufacturers the system is designed for optimal performance with Pelco Coaxitron control products within the length specified for coaxial cable To compensate for coaxial control systems from other manufacturers Pelco has provided DIP switch SW2 3 Setting SW2 3 to the ON position may improve dome control with these control systems If you are using a Pelco Coaxitron controller leave SW2 3 in the default OFF position NOTES e This coaxial control system compatibility feature is only available for dome drive revisions A4 and later revisions AO and later for Spectra IV Horizon dome drives The revision number can be found on the barcode label on the top of the dome drive Software version 1 090 and later indicates this mode is available by placing an asterisk next to the switch number in the Dip Switch Information menu e In some configurations Pelco CM9502 Series matrix systems use nonstandard Coaxitron commands for functions like pattern playback If you experience problems with these functions set SW2 3 to the ON position C3463M B 2 11 Pelco P Protocol Control Systems To compensate for Pelco P protocol control systems from other manufacturers set SW2 3 to the ON position This may improve dome control with some of these control systems SW2 SWITCHES 4 AND 5 SERIAL PORT SETTINGS RS 422 Setting Default SW2 4 and SW2 5 should both be set to the OFF position for RS
60. e the shutter speed to operate automatically Auto or manually Numeric Value AUTO default The electronic shutter speed is set automatically by the amount of light sensed by the camera NUMERIC VALUE Spectra IV dome systems have several numerical shutter speed settings The higher the number the faster the electronic shutter The slowest shutter speed setting is 2 1 2 second The fastest setting is 30 000 1 30 000 second Increasing the shutter speed lowers the light sensitivity and reduces the streaking of fast moving objects Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment This will eliminate any flicker that may occur in the picture AGC LIMIT AGC limit allows users to adjust how the system balances AGC automatic gain control and electronic shutter in low light conditions As scene lighting decreases the system will automatically adjust adding a mixture of AGC and slow shutter according to the AGC limit setting AGC limit can be set between 0 and 40 with 40 applying maximum AGC before slow shutter In contrast setting AGC limit to 0 will force the system software to apply maximum slow shutter as defined by the low light limit setting before any AGC is applied The default AGC settings vary depending on camera model NOTE The maximum slow shutter that the system will achieve is 1 2 second shutter refer to Low Light Limit on page 24 AUTO IRIS Auto iris is the lens function that au
61. e window blank remains activated or deactivated until another configured event changes the state of the window or you modify it through the Window Blanking menu Refer to Window Blanking on page 41 AUX An auxiliary event turns on off an auxiliary output when the event triggers Refer to Aux on page 46 ALARM alarm event executes the action associated with the specified alarm number Refer to Alarms page 44 PATTERN A pattern event starts a previously defined pattern when the event Is triggered Refer to Patterns on page 39 CAMERA A camera event assigns the camera settings of a preset to the current camera settings located in the Camera menu Refer to Camera on page 23 The preset that is referenced by the event must be defined prior to setting up a camera event For the camera event to function the referenced preset must have Custom Camera Settings activated Refer to Presets on page 34 ALL ALARMS An all alarms event enables or disables the reporting of all alarms when the event is triggered PRESET A preset event executes a previously defined preset when the event is triggered Refer to Presets on page 34 NOTES e fyou have camera settings defined in the Camera menu that you wish to restore following a camera event which overwrites those settings you must save the original settings as a separate preset prior to the camera event being triggered You can then set a second camera event to call the preset that has the original
62. eased and smaller movements that may not be as significant will not be tracked START TIME Start time is the amount of time between the execution of a user command and the start of auto tracking The start time can be set between 1 and 10 minutes The default setting is 1 minute Z00M When zoom is enabled the camera automatically zooms in or out to keep the object of interest in the main field of view There are two settings ON default Automatic zoom is enabled OFF Automatic zoom is disabled LOST ACTION If the object of interest is lost from the field of view and there is no other moving object to track the camera will either stop automatic PTZ or will zoom out to attempt to relocate a moving object There are two settings STOP default Automatic PTZ stops if the object of interest is lost from the field of view ZOOM OUT The camera zooms out to attempt to relocate the object of interest or to locate a new moving object to auto track RETURN Return is the amount of time after the last motion has been detected and the time at which the camera returns to the location where auto tracking began Return can be set between 10 and 60 seconds or it can be turned off The default setting is OFF C3463M B 2 11 POWER UP Applies to 27X and 35X models only POWER UP ACTION SPECTRA IV DOME SETTINGS LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE C
63. es preset ZONE LABEL Identifies zone ZOOM Identifies the amount of magnification AZIMUTH ELEVATION Amount of pan from zero degrees vertical and the amount of tilt from zero degrees horizontal DIRECTION Displays compass direction ALARM MESSAGE Displays activated alarm DATE TIME Displays current date and time EVENT LABEL Displays activated event A preset label is displayed when a preset is called A zone label is displayed when the system moves into a zone The zoom ratio label is displayed when zoom is activated Azimuth elevation and direction labels are displayed when pan tilt is activated An alarm message appears on the monitor when an alarm occurs An event label appears on the monitor when an event occurs The following settings are available for each label except date and time OFF Label is not displayed when activated CONSTANT The label is continually displayed when activated 2 SECONDS The label is displayed for 2 seconds after activation 5 SECONDS The label is displayed for 5 seconds after activation 10 SECONDS The label is displayed for 10 seconds after activation The settings for date and time are ON or OFF This setting applies to Pressurized Spectra IV dome systems only t Azimuth is the pan angle from zero to 359 degrees Elevation is the tilt position from zero horizon to 90 degrees C3463M B 2 11 21 LABEL POSITIONS SPECTRA IV DISPLAY SETUP LABEL POSITION LANGUAGE PRESET LAB
64. ets that can be configured are numbered 1 to 32 35 to 82 and 100 to 256 NOTE The number of available presets may be limited by the head ins controllers and DVRs that are connected to your dome system Each of the user definable presets can be configured to use pan tilt camera settings and motion detection The following presets are predefined for specific functions Preset 33 Flip command pans the dome drive 180 degrees Preset 34 Pan zero command directs the dome drive to the factory determined zero reference point Preset 83 to 87 Reserved Preset 88 IR filter IN color Preset 89 IR filter OUT black white Preset 90 to 91 Manual limit stops Preset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menu Preset 96 Stop a scan Preset 97 Random scanning Preset 98 Frame scanning Preset 99 Start auto scanning NOTE For American Dynamics controllers with only 32 presets switch SW2 1 on the dome drive to the ON position When SW2 1 is ON several presets change refer to Table D Table D Presets for American Dynamics Controllers Spectra IV Presets p d 88 21 89 22 90 23 91 24 92 25 93 26 95 28 96 29 97 30 98 31 99 32 the limit stops are turned off presets 23 to 26 can be used as regular presets C3463M B 2 11 35 Use the following steps to configure a preset 1 Select the preset number a
65. g device you are using always combines the odd and even fields in the specified order There are three field alignment settings OFF default Field alignment is disabled Use this setting if you are using an analog device system or a digital encoder that does not support PsF ODD Arranges the odd field for a particular video frame before the even field for that frame EVEN Arranges the even field for a particular video frame before the odd field for that frame NOTES e fyou enable field alignment by selecting ODD or EVEN you must disable any deinterlacing settings for the encoding device to achieve maximum resolution e The ODD and EVEN settings require that the sensor scan mode is set to PROGRESSIVE If field align is set to ODD or EVEN the sensor scan mode automatically changes to PROGRESSIVE C3463M B 2 11 LOW LIGHT SHARPNESS Applies to 27X and 35X models only Low light sharpness allows you to control the video sharpness in low light scenes The available settings are 20 10 DEFAULT 10 and 20 Increasing the value increases sharpness in low light scenes but also increases video noise Decreasing the value decreases video noise in low light scenes but it also decreases image sharpness NOTE Changing the low light sharpness causes the camera to reset which resets all camera settings to their factory defaults MINIMUM FOCUS DISTANCE Applies to 27X and 35X models only Minimum focus distance improves fo
66. ge DD4CBW35 X Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise Wide Dynamic Range C3463M B 2 11 NTSC 2 1 Interlace 1 1 Progressive user selectable 1 4 inch CCD 768 H X 494 V 5540 TV lines 1 4 focal length 3 4 119 mm 35X optical zoom 12X digital zoom 3 2 4 6 6 6 seconds 55 8 at 3 4 mm wide zoom 1 7 at 119 mm telephoto zoom Automatic with manual override 0 55 lux at 1 60 sec shutter speed color 0 018 lux at 1 2 sec shutter speed color 0 00018 lux at 1 2 sec shutter speed B W Internal AC line lock phase adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 2 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB 128X PAL 2 1 Interlace 1 1 Progressive user selectable 1 4 inch CCD 752 H X 582 V gt 540 TV lines 1 4 focal length 3 4 119 mm 35X optical zoom 12X digital zoom 3 2 4 6 6 6 seconds 55 8 at 3 4 mm wide zoom 1 7 at 119 mm telephoto zoom Automatic with manual override 0 45 lux at 1 50 sec shutter speed color 0 015 lux at 1 1 5 sec shutter speed color 0 00015 lux at 1 1 5 sec shutter speed B W Internal AC line lock pha
67. he joystick to position the cursor beside menu selection NOTE If your controller does not have a joystick use the up or down key 3 Press Iris Open the submenu cursor moves to the right 4 Move the joystick up or down to view selections 5 Press Iris Open to make a selection 6 Press Iris Close to cancel a selection Digital zoom magnifies the image electronically and the picture may appear pixilated The larger the digital zoom limit the greater the reduction in resolution dome cannot do electronic zoom in a pattern Optical zoom will operate in a pattern 10 C3463M B 2 11 PRESET 95 ACCESSING MAIN MENU You can call up the main menu on your monitor by configuring setting or creating preset 95 preset 28 in AD 32 preset mode Configuring preset 95 for Pelco s controllers varies according to the type of controller you are using Instructions for configuring preset 95 are given below for various Pelco controllers CM6700 CM6800 1 Enter the number of the Spectra IV dome system and press the CAM key 2 Enter 95 and hold the PRESET key for two seconds 3 In the Edit Preset menu go to SET and press the ACK key The main menu appears KBD200A KBD300A Direct Mode Only 1 Enter 95 2 Hold the PRESET key approximately five seconds until the main menu appears on the screen CM9500 1 Enterthe number of the Spectra IV dome system and press the CAM key The main menu appears 2 Highlight SETUP in the main men
68. hy or complex there is a possibility that there may not be enough remaining memory to configure all eight patterns for the 27X and 35X models To configure a pattern 1 Use the joystick to position the cursor beside PATTERN NUMBER Press Iris Open The cursor moves to the right 2 Move the joystick up or down to view selections Press Iris Open to enter selection 3 Use the joystick to position the cursor beside PROGRAM PATTERN 4 Press Iris Open The Patterns configuration window appears 5 Follow the directions displayed on the monitor After a pattern is configured the remaining storage percentage is displayed on the screen This is the amount of memory available to configure the remaining patterns To clear a pattern 1 Use the joystick to position the cursor beside CLEAR PATTERN 2 Press Iris Open 3 Follow the directions displayed on the monitor To edit the pattern schedule The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on page 53 with the following exceptions In the Edit Schedule menu the event type cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For instructions on changing the features in the Edit Schedule menu refer to Edit Event on page 54 NOTE When configuring one or more presets within a pattern use the normal controller commands to call a preset Not all controllers can start all patterns However any of the patterns can be automati
69. ing is ON the iris will not close completely even in manual mode C3463M B 2 11 27 NOTE Wide dynamic range is disabled when electronic image stabilization is set to 5 Hz or 10 Hz Wide Dynamic Range ON Wide Dynamic Range OFF Figure 3 Wide Dynamic Range Settings LOW LUX NOISE REDUCTION Applies to 27X and 35X models only Low lux noise reduction helps to reduce video noise in low light scenes When enabled low lux noise reduction is directly affected by the AGC settings for the dome system The following are the low lux noise reduction settings ON default Low lux noise reduction is enabled As the scene darkens and AGC increases the noise reduction effect automatically increases As noise reduction increases you may also notice some afterimaging and a slight reduction in color saturation OFF Low lux noise reduction is disabled VIDEO LEVEL Set the video output to one of the following options NORMAL 1 0 Vp p HIGH default setting 1 2 Vp p to compensate for losses in video cable FIELD ALIGN Field align determines whether the camera produces progressive segmented frame output PsF or interlaced frame output Analog video from the camera is always output in separate fields as required for compatibility This feature allows PsF to be recombined by an encoding device without a time difference between fields as is typically seen from interlaced analog video output Enabling field align requires that the encodin
70. ings for SW1 Pelco D Type Control 4 of 6 SPERA SWITCH SETTING ADDRESS SW1 2 SW1 3 SWI 4 SWI 5 SW1 6 SWI 7 148 OFF OFF ON OFF ON OFF OFF ON 149 ON OFF ON OFF ON OFF OFF ON 150 OFF ON ON OFF ON OFF OFF ON 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ON 159 ON ON ON ON ON OFF OFF ON 160 OFF OFF OFF OFF OFF ON OFF ON 161 ON OFF OFF OFF OFF ON OFF ON 162 OFF ON OFF OFF OFF ON OFF ON 163 ON ON OFF OFF OFF ON OFF ON 164 OFF OFF ON OFF OFF ON OFF ON 165 ON OFF ON OFF OFF ON OFF ON 166 OFF ON ON OFF OFF ON OFF ON 167 ON ON ON OFF OFF ON OFF ON 168 OFF OFF OFF ON OFF ON OFF ON 169 ON OFF OFF ON OFF ON OFF ON 170 OFF ON OFF ON OFF ON OFF ON 171 ON ON OFF ON OFF ON OFF ON 172 OFF OFF ON ON OFF ON OFF ON 173 ON OFF ON ON OFF ON OFF ON 174 OFF ON ON ON OFF ON OFF ON 175 ON ON ON ON OFF ON OFF ON 176 OFF OFF OFF OFF ON ON OFF ON 177 ON OFF OFF OFF ON ON OFF ON 178 OFF ON OFF OFF ON ON OFF ON 179 ON ON OFF OFF ON ON OFF ON 180 OFF OFF ON OFF ON ON OFF ON 181 ON OFF ON OFF ON ON OFF ON 182 OFF ON ON OFF ON ON OFF ON 183 ON ON ON OFF ON ON OFF ON 184 OFF OFF OFF ON ON ON OFF ON 185 ON OFF OFF ON ON ON
71. itar rta Ne ceris e Ste ege hPa Le Me EL e TE m d 58 C3463M B 2 11 software Eanguage File Upload ERE te ete a a o y EUR 59 yau 60 Specifications bee Asean ty es 61 234 taht Ge teh e cd e pri uu a o 61 ZIXIMDUels E ERTE AS bsc ae he 62 oe vaches a sc rm e ewe co A ak Naan Me tbat a 63 Appendix UE 64 C3463M B 2 11 5 Description Spectra IV SL and Spectra IV SE are Pelco s premier integrated dome systems These systems feature a high resolution camera optics package with configurable dome drive software This manual is designed primarily to be a reference tool for the installation and operation of your system Inside you will find information about features and commands as well as a detailed menu tree and a quick start guide Be sure to thoroughly familiarize yourself with the information in this manual before installing and using your system C3463M B 2 11 Installation This manual contains installation instructions for the Spectra IV dome drive only For complete installation instructions for a Spectra IV dome system refer to the installation manual that was shipped with the back bo
72. lowing are the settings for daylight savings OFF Daylight saving time will be turned off FIXED DATE Daylight saving time occurs on the same date each year RELATIVE DATE Daylight saving time occurs on a different date each year such as the first Sunday in April This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 51 52 7 If FIXED DATE was selected the following information appears CLOCK a the joystick to position th appears Press Iris Ope b Usethe joystick to position th month appears Press C Usethe joystick to position th appears Press Iris Ope d Use the joystick to position th Use the joys start time e Repeat steps b through If RELATIVE DATE was selec TIME BASE TIME FORMAT SET TIME DATE FORMAT SET DATE INTERNAL CLOCK 12 HOUR 00 00 AM MM DD YYYY 00 00 0000 DAYLIGHT SAVINGS FIXED DATE TIME SHIFT START DATE MONTH DAY START TIME D DATE MONTH DAY D TIME n to select the time shift 1 HOUR MARCH 1 02 00 AM NOVEMBER 1 02 00 AM e cursor beside TIME SHIFT Press Iris Open Scroll through the options until the desired selection cursor beside the start date MONTH Press Iris Open Scroll through the options until the desired ris Open to select the month cursor beside the start date DAY Press Iris Open Scroll through the options until the desired date n to select the day e cur
73. me There are two auto flip modes ON default Auto flip mode is enabled OFF Auto flip mode is disabled PROPORTIONAL PAN Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings This keeps the image from moving too fast on the monitor when there is a large amount of zoom There are three proportional pan modes ON default Enables the proportional pan mode OFF Disables proportional pan mode The pan speed will not depend on the amount of zoom 2X Increases the speed of the proportional pan mode to twice that used when proportional pan is set to ON This setting applies to Pressurized Spectra IV dome systems only C3463M B 2 11 29 PARK This feature allows the dome to begin a specified operation scan preset or pattern after configured period of inactivity Park time can be configured from 1 to 720 minutes 12 hours or set to zero which disables this feature The default setting is zero Park Action This feature will define the activity when the dome parks The following settings are available NONE default No action AUTO SCAN Dome starts auto scan operation FRAME SCAN Dome starts frame scan operation RANDOM SCAN Dome starts random scan operation PATTERN 1 Dome runs pattern 1 PATTERN 2 Dome runs pa
74. modes of operation color and black white You can increase sensitivity in low light conditions by switching to black white mode removing the IR cut filter Color mode is preferred in normal lighting conditions The following are the settings for the IR cut filter OFF Manual operation is controlled by preset 88 filter IN and 89 filter OUT AUTO default Automatic operation is controlled by the auto IR level setting IN Images are always displayed in color mode OUT Images are always displayed in black white mode NOTE The IN and OUT settings are available when editing camera settings through the Camera and Presets menus refer to Camera on page 23 and Presets on page 34 Auto IR Level The auto IR level is the light level at which the infrared filter switches IN or OUT Following are the available settings for the auto IR level DUSK default Approximately 6 lux black white approximately 13 lux color DARK Approximately 0 1 lux black white approximately 2 lux color NOTES e If backlight compensation is ON and the IR cut filter switches OUT in normal lighting conditions adjust the Auto IR Level to a darker setting Refer to Backlight Compensation on page 27 e low light does not mean no light Some type of illumination is required street light IR light etc The camera is not sensitive to IR light when the IR cut filter is IN Low Light Focus Applies to 27X and 35X models only If you are using an
75. n 60 60 to 92 below horizon 70 18 above horizon to 70 below horizon 70 70 to 92 below horizon 80 18 above horizon to 80 below horizon 80 80 to 92 below horizon CAMERA Figure 7 Window Blank Tilt Angles C3463M B 2 11 ALARMS LANGUAGE lt CAMERA gt RESUME ALARM NUMBER lt MOTION gt SEQUENCE SECS lt SYSTEM INFORMATION gt AUTO TRACKING RESET DELAY SECS ALARM PRIORITY lt DISPLAY SETUP gt lt POWER UP gt ALARM ACTION lt DOME SETTINGS LINE SYNC ALARM SETTINGS ACTIVATE AUX ALERT lt PRESETS gt lt PATTERNS gt EXIT lt EDIT SCHEDULE gt CYCLE CAMERA POWER lt ZONES gt BACK REBOOT SYSTEM lt WINDOW BLANKING gt EXIT EXIT lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT The 23X models have one alarm input available The 27X and 35X models have seven alarm inputs Alarm inputs can be configured as high medium or low priority When an alarm is received an input signal to the dome triggers the user defined action go to preset run pattern etc configured for the alarm NOTE Refer to the notation in step 6 for the limited alarm features available for 23X models There are three global alarm settings RESUME This mode lets the dome resume its previous activity scan patte
76. ns that appear on the screen When all four corners are set the SET WINDOWS menu reappears the blanked area is displayed and the ENABLE WINDOW option is set to YES NOTES e Use the outside corner of the window selection tool as a guide when selecting the upper left upper right bottom right and bottom left corners of the window OUTSIDE CORNER Figure 5 Window Selection Tool C3463M B 2 11 41 42 e Set windows are not visible when editing a new window location Disabled Enabled Figure 6 Window Blanking 6 The blanked area can be configured to turn on or off at specified zoom point To set the zoom point a Use the joystick to position the cursor beside EDIT WINDOW ZOOM and then press Iris Open b Zoom in to the point where you want window blanking to turn on Press Iris Open to set the zoom point NOTES e Since the area is already blanked out it may be difficult to determine when you want window blanking to turn on Reverse the window before setting the zoom point When finished reverse the window again to blank out the area e Increase the size of the window if any part of the blanked area is revealed during PTZ operations EDIT SCHEDULE The Edit Schedule menu is a duplicate of the Edit Event menu refer to Event on page 53 with the following exceptions In the Edit Schedule menu the event type cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For i
77. nstructions on changing the features in the Edit Schedule menu refer to Fdit Event on page 54 REVERSE A blanked out area can be reversed to make it visible and the areas on both sides of it not visible The areas above and below the blanking area remain visible Reversing the window a second time will return it to its original condition CLEAR WINDOW All areas that have been set for window blanking are cleared C3463M B 2 11 BLANK ALL ABOVE BLANK ALL BELOW The Blank All Above and Blank All Below options add additional flexibility to setting up privacy areas These settings are ideal for applications where a complete pan location needs to be blanked Table E Window Blank Settings Blank All Above Blank All Below Tilt Angle Blanked Area Tilt Angle Blanked Area OFF No blanking OFF No blanking 15 15 above horizon to 18 above horizon 10 10 above horizon to 18 above horizon E 0 Horizon to 18 above horizon 0 Horizon to 92 below horizon 10 18 above horizon to 10 below horizon 10 10 to 92 below horizon 20 18 above horizon to 20 below horizon 20 20 to 92 below horizon 30 18 above horizon to 30 below horizon 30 30 to 92 below horizon 40 18 above horizon to 40 below horizon 40 40 to 92 below horizon 50 18 above horizon to 50 below horizon 50 50 to 92 below horizon 60 18 above horizon to 60 below horizo
78. o zoom Automatic with manual override 0 55 lux at 1 60 sec shutter speed color 0 018 lux at 1 2 sec shutter speed color 0 00018 lux at 1 2 sec shutter speed B W Internal AC line lock phase adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 2 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB 128X PAL 2 1 Interlace 1 1 Progressive user selectable 1 4 inch CCD 752 H X 582 V gt 540 TV lines 1 4 focal length 3 4 119 mm 35X optical zoom 12X digital zoom 3 2 4 6 6 6 seconds 55 8 at 3 4 mm wide zoom 1 7 at 119 mm telephoto zoom Automatic with manual override 0 45 lux at 1 50 sec shutter speed color 0 015 lux at 1 1 5 sec shutter speed color 0 00015 lux at 1 1 5 sec shutter speed B W Internal AC line lock phase adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 1 5 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB 128X C3463M B 2 11 35X MODELS DD4CBW35 Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed optical range Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise Wide Dynamic Ran
79. on page 55 NOTE Holidays cannot be changed through the Edit Schedule option from the Preset Pattern Window Blanking Alarm or Aux menus EDIT HOLIDAY Use the following steps to edit a holiday 1 Use the joystick to position the cursor beside EDIT EVENT LABEL 2 Press Iris Open 3 Use the joystick to position the cursor beside OCCURRENCE Press Iris Open The following are the settings for Occurrence FIXED DATE The holiday occurs on the same date each year RELATIVE DATE The holiday occurs on a different date each year such as the third Sunday in April C3463M B 2 11 55 56 4 If FIXED DATE was selected as the occurrence the following information appears EDIT HOLIDAY OCCURRENCE FIXED DATE MONTH JANUARY DAY 1 BACK EXIT a the joystick to position the cursor beside MONTH Press Iris Open Scroll through the options until the desired month appears Press Iris Open to select the month b Use the joystick to position the cursor beside DAY Press Iris Open Scroll through the options until the desired date appears Press Iris Open to select the day 5 If RELATIVE DATE was selected as the occurrence a Use the joystick to position the cursor beside MONTH Press Iris Open Scroll through the options until the desired month appears Press Iris Open to select the month b Use the joystick to position the cursor beside WEEK Press Iris Open Scroll through the options until the desired week appears Press
80. on set to YES To edit a zone label 1 Use the joystick to position the cursor beside EDIT ZONE LABEL 2 Press Iris Open The following information appears LABEL FOR ZONE ZONE NUMBER 1234567890 ABCDEFGHIJ KLMNOPORST UVWXYZ BACKSPACE abcdefghij SPACE uvwxyz 3 Use the joystick to position the cursor beside a character Press Iris Open to enter selection To clear a character position the cursor beside BACKSPACE and then press Iris Open 4 When the label is completed move the cursor to OK Press Iris Open to return to the Zones menu To disable a zone a zone is enabled automatically when it is configured or to blank a zone 1 Move the cursor beside ZONE ENABLED or ZONE BLANKING 2 Press Iris Open The cursor moves to the right 3 Move the joystick up or down to view selections Press Iris Open to enter selection To clear a zone 1 Use the joystick to position the cursor beside CLEAR ZONE 2 Press Iris Open Follow the instructions on the screen This setting applies to Pressurized Spectra IV dome systems only 40 C3463M B 2 11 WINDOW BLANKING LANGUAGE lt CAMERA gt STYLE WINDOW NUMBER SYSTEM INFORMATION EDIT WINDOW LOCATION lt gt lt AUTO TRACKING gt BLANK ALL ABOVE lt gt lt DISPLAY SETUP gt lt POWER UP gt BLANK ALL BELOW lt EDIT WINDOW ZOOM gt lt DOME SETTINGS gt lt LINE SYNC gt lt EDIT SCHEDULE gt ACK ALERT lt PRESETS gt lt SET
81. ons In the Edit Schedule menu the event type cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For instructions on changing the features in the Edit Schedule menu refer to Edit Event on page 54 NOTES There are two additional options available for the IR cut filter that are only available when configuring a preset The additional settings are IN and OUT If the IR cut filter is set to IN the preset scene will be in color If the IR cut filter is set to OUT the preset scene will be in black white You can copy camera settings from one preset to another preset To copy camera settings do the following 1 Use the joystick to position the cursor beside COPY CAMERA SETTINGS 2 Press Iris Open The cursor moves to the right 3 Move the joystick up or down to view selections Press Iris Open to enter selection The Apply to Global setting allows camera settings specified for a particular preset to remain in effect even after the preset has been completed C3463M B 2 11 MOTION DETECTION Applies to 27X and 35X models only SPECTRA IV DOME SETTINGS PRESETS MOTION DETECTION LANGUAGE lt CAMERA gt ER MOTION DETECTION ENABLED lt MOTION gt lt SYSTEM INFORMATION gt AUTO TRACKING EDIT DETECTION AREAS DISPLAY SETUP POWER UP D ACTIVATE AUX lt DOME SETTINGS gt lt LINE SYNC gt lt EDIT CAMERA SETTINGS gt AUX TIME SECS ACK ALERT lt PRESETS gt lt MOTION
82. page 53 with the following exceptions In the Edit Schedule menu the event type cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For instructions on changing the features in the Edit Schedule menu refer to Edit Event on page 54 This setting applies to Press 46 urized Spectra IV dome systems only C3463M B 2 11 TITLE TEXT LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT DOME SETTINGS TITLE TEXT ENABLE TITLE TEXT lt EDIT TITLE TEXT gt BACK EXIT Title text is the label used to identify the camera viewed on the monitor Up to 20 characters can be used for a title To edit the title text label do the following 1 Use the joystick to position the cursor beside EDIT TITLE TEXT 2 Press Iris Open The following information appears EDIT TITLE TEXT 1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZ abcdefghij klmnopqrst uvwxyz amp OK CANCEL BACKSPACE SPACE 3 Use the joystick to position the cursor beside a character Press Iris Open
83. pectra IV dome systems only C3463M B 2 11 LINE SYNC LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT Line sync refers to a configurable f Spectra IV dome systems automati DOME SETTINGS CAMERA lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT LINE SYNC LINE SYNC LINE SYNC PHASE unction that allows you to synchronize all cameras within a matrix system cally sense V Sync input No line sync setup is required for Pelco control systems that provide a V Sync signal For matrix systems that do not output V Sync there are two settings for line synchronization ON Adjusts the phase of the line sync to synchronize input power Line sync phase settings range from zero to 359 degrees OFF default The dome synchronizes to the internal clock PRESETS LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS g
84. previous step for the remaining days of the week e Use the joystick to position the cursor beside HOLIDAY Press Iris Open The following are the holiday settings SKIP HOLIDAYS The event will not occur on a day of the week for which it is set if that date is in the list of holidays ON The event will activate on holidays that are set in the Event menu in addition to its normally scheduled days of the week OFF The event only occurs on the days of the week that it is scheduled holidays have no effect on the event CLEAR EVENT To clear an event 1 Use the joystick to position the cursor beside CLEAR EVENT 2 Press Iris Open 3 Follow the directions displayed on the monitor LIST EVENT To list events 1 Use the joystick to position the cursor beside LIST EVENT 2 Press Iris Open 3 All configured events will be listed HOLIDAY Use the following steps to create a new holiday 1 Use the joystick to position the cursor beside HOLIDAY Press Iris Open 2 Move the joystick up or down to scroll through the options If no holidays were created in the past NEW is the only selectable option Press Iris Open to select NEW 3 Proceed to Edit Holiday on page 55 Use the following steps to manage an existing holiday 1 Use the joystick to position the cursor beside HOLIDAY Press Iris Open 2 Move the joystick up or down to scroll through the holidays Press Iris Open to enter a selection 3 Proceed to Edit Holiday
85. r left arrows below the Go to Preset button until Go to Preset 95 appears on the button 3 Click the Go to Preset 95 button The main menu appears DIGITAL SENTRY DS CONTROLPOINT 1 Click the PTZ Controls icon The PTZ Control tab appears below the PTZ video frame 2 Click the up and down arrows to display 95 in the Preset Name text box 3 Click the Call button The main menu appears DVR5100 1 While in live view mode select a video pane that is displaying video from a Spectra IV dome system 2 From the Main menu click Actions The Actions menu appears 3 From the Actions menu click PTZ Operations The PTZ Operations dialog box appears 4 In the PTZ Operations dialog box type 95 in the text box and then click Presets The main menu appears C3463M B 2 11 23X LowLight Day Night Menu Tree SPECTRA IV LANGUAGE ENGLISH lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM SYSTEM INFORMATION SERIAL X0000000000000 DISPLAY SETUP PRESET LABEL 2 SECS DOME DRIVE MODEL BACK BOX MEMORY SOFTWARE VERSION BUILD FONT VERSION COMM D ADDRESS P ADDRESS CM9500 MODE 32 PRESETS PROTOCOL PRESSURIZED lt ADDITIONAL gt FREE MEMORY LAST RESET XX XXXX AVAILABLE XXXXXXXXXX 1 2 OFF OFF C ADDITIONAL AZIMUTH ZERO OFFSET MOTOR ACTIVE CAMERA ACTIVE VIDEO LEVEL CAMERA MODE
86. re alert occurs if the temperature is above 140 F 60 C The low temperature alert occurs if the temperature is below 40 F 40 C The high pressure alert occurs if the pressure is above 13 PSIG The low pressure alert occurs if the pressure is below 1 PSIG The dew point high humidity alert occurs if the difference between the temperature and the dew point is less than or equal to 3 C NOTE The normal operating temperature inside the unit will be greater than the temperature outside the back box due to the heat emitted by the systems electronics RESET ALERT Reset alert clears the alert condition and removes the alert label from the monitor The system automatically checks internal conditions 60 seconds after reset If conditions are still unacceptable the alert label reappears on the screen indicating further corrective action is required C3463M B 2 11 49 CLEAR SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt ACK ALERT RESET CAMERA CYCLE CAMERA POWER REBOOT SYSTEM EXIT DOME SETTINGS lt CAMERA gt lt MOTION gt lt AUTO TRACKING gt lt POWER UP gt lt LINE SYNC gt lt PRESETS gt lt PATTERNS gt lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEA
87. rn or previous position after all alarms are cleared SEQUENCE This is the time the dome will perform an alarm activity when more than one alarm of the same priority occurs at the same time RESET DELAY This is the amount of time the dome considers the alarm to be active after it has physically cleared Use the following steps to configure the alarm settings 1 Use the joystick to position the cursor beside ALARM SETTINGS Press Iris Open 2 Select the alarm number a Use the joystick to position the cursor beside ALARM NUMBER b Press Iris Open The cursor moves to the right c Move the joystick up or down to view selections Press Iris Open to enter selection 3 Select the alarm priority a Use the joystick to position the cursor beside ALARM PRIORITY b Press Iris Open The cursor moves to the right c Move the joystick up or down to view the available selections Available settings include HIGH MEDIUM and LOW default If multiple alarms with different priorities are active at the same time the dome will only go to the alarms with the highest priority d Press Iris Open to enter selection HIGH Alarm action takes highest priority and will override manual PTZ control MEDIUM LOW Alarm action will not occur if an alarm occurs during manual pan tilt and zoom control This setting applies to Pressurized Spectra IV dome systems only 44 C3463M B 2 11 4 5 C3463M B 2 11 Set the alarm action a Use
88. se adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 1 5 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB 128X 63 Appendix 64 Table F Switch Settings for SW1 Pelco P Type Control SPECTRA SWITCH SETTING ADDRESS SW1 1 SW1 2 SW1 3 SW1 4 SW1 5 SW1 6 SW1 7 SW1 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF OFF OFF OFF OFF OFF 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OFF 8 ON ON ON OFF OFF OFF OFF OFF 9 OFF OFF OFF ON OFF OFF OFF OFF 10 ON OFF OFF ON OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF 12 ON ON OFF ON OFF OFF OFF OFF 13 OFF OFF ON ON OFF OFF OFF OFF 14 ON OFF ON ON OFF OFF OFF OFF 15 OFF ON ON ON OFF OFF OFF OFF 16 ON ON ON ON OFF OFF OFF OFF 17 OFF OFF OFF OFF ON OFF OFF OFF 18 ON OFF OFF OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON OFF OFF OFF 20 ON ON OFF OFF ON OFF OFF OFF 21 OFF OFF ON OFF ON OFF OFF OFF 22 ON OFF ON OFF ON OFF OFF OFF 23 OFF ON ON OFF ON OFF OFF OFF 24 ON ON ON OFF ON OFF OFF OFF 25 OFF OFF OFF ON ON OFF OFF OFF 26 ON OFF OFF ON ON OFF OFF OFF 27 OFF ON OFF ON ON OFF OFF OFF 28 ON ON OFF ON ON OFF OFF OFF 29 OFF OFF ON ON ON OFF OFF OFF 30 ON OFF ON ON ON OFF OFF OFF 3
89. sor beside START TIME Press Iris Open Scroll through the hours until the desired time appears d for the ending date and time TIME BASE TIME FORMAT SET TIME DATE FORMAT SET DATE DAYLIGHT SAVINGS TIME SHIFT START DATE MONTH WEEK DAY START TIME END DATE MONTH WEEK DAY END TIME BACK EXIT ed the following information appears CLOCK INTERNAL CLOCK 12 HOUR 00 00 AM MM DD YYYY 00 00 0000 RELATIVE DATE 1 HOUR MARCH 2ND MONDAY 02 00 AM NOVEMBER 1ST MONDAY 02 00 AM Follow the instructions in step 7 for FIXED DATE adding WEEK ick to move the cursor to the right Scroll through the minutes until the desired time appears Press Iris Open to select the C3463M B 2 11 Applies to 27X and 35X models only SPECTRA IV DOME SETTINGS LANGUAGE lt CAMERA gt EVENT TYPE EVENT LABEL lt SYSTEM INFORMATION gt MOONS lt AUTO TRACKING gt lt DISPLAY SETUP gt POWER UP gt lt EDIT EVENT LABEL gt lt DOME SETTINGS NE SYNC EDIT EVENT ACK ALERT RESETS gt LEAR EVENT gt RESET CAMERA PATTERNS gt ST EVENT CYCLE CAMERA POWER REBOOT SYSTEM FDA LARMS gt lt EDIT HOLIDAY gt UX gt lt CLEAR HOLIDAY gt TLE TEXT gt lt LIST HOLIDAYS gt LERT gt LEAR gt BACK EXIT PASSWORD gt LOCK gt lt EVENT gt BACK EXIT REFERENCE INFORMATION An event is a preconfigured camera park scan preset pattern window blanking alarm or auxiliary
90. t lt ZONES gt lt WINDOW BLANKING gt lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT PRESETS 1 ER OT DEFINED LABEL gt SCENE gt lt EDIT CAMERA SETTINGS gt lt MOTION DETECTION gt lt EDIT SCHEDULE gt lt CLEAR PRESET gt lt CLEAR CAMERA SETTINGS gt lt APPLY TO GLOBAL gt BACK EXIT REFERENCE INFORMATION AZIMUTH ELEVATION ZOOM RATIO CUSTOM CAMERA SETTINGS The model of the back box you are using limits the number of configurable presets that can be stored and retrieved in the back box memory If you are using an older model back box you may configure and use up to the maximum number of presets available to the dome drive However if the dome drive is changed the back box model will limit the number of stored presets available to the new dome drive refer to Table Table C Stored Presets by Back Box Model Back Box Series Model Number of Stored Presets Spectra Spectra SL Spectra SE Spectra Ill BB53 99 15 Spectra IV BB4 64 256 This setting applies to Pressurized Spectra IV dome systems only 34 C3463M B 2 11 The Spectra IV SL dome system which includes 23X models has 64 preset positions The presets that can be configured are numbered 1 to 32 and 35 to 64 The Spectra IV SE dome system which includes 27X and 35X models has 256 preset positions The pres
91. t EDIT CAMERA SETTINGS gt LOCATION 0 lt MOTION DETECTION gt SENSITIVITY MEDIUM lt EDIT SCHEDULE gt DETECTION AREA 3 lt CLEAR PRESET gt LOCATION 0 lt CLEAR CAMERA SETTINGS gt SENSITIVITY MEDIUM lt APPLY TO GLOBAL gt DETECTION AREA 4 LOCATION 0 REFERENCE INFORMATION SENSITIVITY MEDIUM AZIMUTH ELEVATION ZOOM CUSTOM CAMERA SETTINGS ALARM SETTINGS RESUME ALARM NUMBER AUX 1 MODE TOGGLE SEQUENCE SECS ALARM PRIORITY DWELL TIME SECS 1 RESET DELAY SECS ALARM ACTION AUX 2 MODE TOGGLE lt ALARM SETTINGS gt ACTIVATE AUX DWELL TIME SECS 1 ALARM CONTACT EDIT SCHEDULE EDIT SCHEDULE TITLE TEXT ENABLE TITLE TEXT EDIT TITLE TEXT gt EDIT THE PASSWORD EVENT EDIT EVENT 1234567890 OK TIME BASE INTERNAL CLOCK EVENT TYPE EVENT LABEL EVENTO ABCDEFGHIJ CANCEL TIME FORMAT 12 HOUR EVENT LABEL KLMNOPORST SET TIME 12 00 AM EVENT ACTIVE ON UVWXYZ BACKSPACE DATE FORMAT MM DD YYYY lt EDIT EVENT LABEL gt EVENT TIME 12 00 AM abcdefghij SPACE SET DATE 00 00 0000 lt EDIT EVENT gt EVENT OCCURS kimnopqrst DAYLIGHT SAVINGS OFF lt CLEAR EVENT gt SUNDAY uvwxyz amp lt LIST EVENT gt MONDAY TUESDAY HOLIDAY WEDNESDAY lt EDIT HOLIDAY gt THURSDAY lt CLEAR HOLIDAY gt FRIDAY lt LIST HOLIDAYS gt SATURDAY ON HOLIDAY SKIP HOLIDAYS REFERENCE INFORMATION EVENT TYPE PRESET NUMBER 1 18 C3463M B 2 11 Language SPECTRA IV LANGUAGE lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DOME SETTINGS gt
92. t can compensate for some forms of external influences In all cases care should be aken to make sure that any dome system is mounted to a rigid location n the event that vibration is introduced to the dome system a user can select one of the electronic image stabilization settings in the menu The available settings are OFF 5 Hz and 10 Hz Users should apply each of the settings to the camera to see which one best addresses the vibration hat is affecting the video quality Electronic image stabilization will not correct for all ranges of vibration If either of the settings fails to eliminate the vibration seen in the video other measures should be taken to isolate the vibration or to seek a more rigid mounting location NOTES e When electronic image stabilization is applied digital slow shutter and wide dynamic range are disabled Zoom image resolution and viewing angle are also limited when this feature is activated e Electronic image stabilization cannot be used while in a preset that has motion detection activated WIDE DYNAMIC RANGE Applies to 27X and 35X models only Wide dynamic range WDR balances the brightest and darkest sections of a scene to produce a picture that is better balanced in lighting and provides more detail Available settings are OFF and ON the default setting is OFF When wide dynamic range is set to ON the frame rate is reduced from the standard 30 to 15 frames per second fps Also when this sett
93. the joystick to position the cursor beside ALARM ACTION b Press Iris Open The cursor moves to the right c Move the joystick up or down to view the available selections The following are the settings for alarm action NONE No action when alarm is triggered AUTO SCAN Dome starts auto scan operation when alarm is triggered FRAME SCAN Dome starts frame scan operation when alarm is triggered RANDOM SCAN Dome starts random scan operation when alarm is triggered PRESET Dome goes to the preset that is the same as the alarm number For example Preset 1 will go to Alarm 1 PATTERN 1 Dome runs pattern 1 when an alarm is triggered PATTERN 2 Dome runs pattern 2 when an alarm is triggered PATTERN 3 Dome runs pattern 3 when an alarm is triggered PATTERN 4 Dome runs pattern 4 when an alarm is triggered PATTERN 5 Dome runs pattern 5 when an alarm is triggered PATTERN 6 Dome runs pattern 6 when an alarm is triggered PATTERN 7 Dome runs pattern 7 when an alarm is triggered PATTERN 8 Dome runs pattern 8 when an alarm is triggered d Press Iris Open to enter selection Set the auxiliary to activate a the joystick to position the cursor beside ACTIVATE AUX b Press Iris Open The cursor moves to the right c Move the joystick up or down to view the following available selections NO default Not activated 1 An alarm action will close AUX 1 2 An alarm action will close
94. tomatically opens and closes the iris in response to changing light conditions You can configure the auto iris to operate automatically or at a user defined level OFF Auto iris is disabled and control is always manual AUTO default The iris is adjusted automatically to produce a constant video output as determined by the auto iris level setting If auto iris is in the auto mode it will remain that way until the iris is manually opened or closed The dome will return to auto mode when it is panned or tilted more than 15 degrees Auto Iris Level Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the camera Increase the value to brighten the scene Decrease the value to darken the scene This setting can be adjusted if the video level in the auto iris mode is too bright or too dark NOTE If backlight compensation is ON decrease the auto iris level setting This setting applies to Pressurized Spectra IV dome systems only 26 C3463M B 2 11 Auto Iris Peak Increasing the peak value will cause the auto iris circuit to react more to highlights or peaks in the picture Decreasing this value will cause it to use the average video level to adjust the iris AUTO SHARPNESS Auto sharpness enhances picture detail by increasing the aperture gain of the camera and sharpening the edges in the picture There are two settings ON default The camera automatically maintains a normal sharpness mo
95. ttern 2 PATTERN 3 Dome runs pattern 3 PATTERN 4 Dome runs pattern 4 PATTERN 5 Dome runs pattern 5 PATTERN 6 Dome runs pattern 6 PATTERN 7 Dome runs pattern 7 PATTERN 8 Dome runs pattern 8 PRESET 1 Dome goes to preset 1 PRESET 8 Dome goes to preset 8 Only 27X and 35X models allow PATTERN 2 through PATTERN 8 SCAN SPEED Scan speed is the degrees per second that the dome will pan when in a scan mode Scan speed is adjustable from 1 to 40 degrees per second through the camera menu The default setting is 25 degrees per second PRESET FREEZE FRAME This feature freezes the scene on the monitor when going to a preset This allows for smooth transition from one preset scene to another Preset freeze frame also reduces bandwidth when used with digital network systems such as PelcoNet and guarantees that blanked areas will not be revealed when going to a preset There are three preset freeze frame settings ON The image on the screen freezes when a preset is called When the dome reaches the preset the image is unfrozen and the preset scene is displayed OFF The image is never frozen AUTO default Freeze frame is turned on automatically if window blanking is ON If window blanking is OFF freeze frame is off LIMIT STOPS Limit stops are configurable stops that limit the pan range of the dome There must be two limits a left and a right to define an area There are two types of limit stops MANUAL A m
96. u and press the SELECT key 3 Highlight CAM in the Setup menu and press the SELECT key 4 Highlight PRESET in the Camera menu and press the SELECT key 5 Enter 95 and press the F1 key The main menu appears CM9740 CM9760 CM9770 CM9780 1 Press the ESCAPE key to open the main menu Select DEF The Define submenu appears 2 Enter your four digit PIN f this is your first time entering this mode 3 Enter 95 and select PRST The main menu appears 4 Select the Quit icon to return to the default menu KBD4000 KBD4002 1 Press the SPOT MONITOR key 2 Enter 95 then hold the PRESET key approximately five seconds until the main menu appears on the screen MPT9500 Extended Coaxitron or RS 485 Mode 1 Enter 95 and press the PRESET SET key 2 Press the F2 key The main menu appears NET300 NET350 NET4001A 1 Check the Set box 2 Click the preset 95 button The main menu appears C3463M B 2 11 ENDURA WORKSTATION 1 Right click in the video pane of the Spectra IV dome system 2 Click Preset and then click Select Preset 3 Enter 95 and then click OK VCD5000 1 Enter 95 for the preset action The shortcuts menu appears 2 Press the Preset button on the KBD5000 DX4100 DX4500 DX4600 D X8100 1 Click the PTZ button on the toolbar The PTZ control appears 2 Click the Program button on the PTZ control The main menu appears DIGITAL SENTRY SYSTEM SOFTWARE 1 Click the PTZ tab 2 Click the right o
97. ust be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment REVISION HISTORY Manual Date Comments C3463M 10 09 Original version C3463M A 1 0 Revised manual to include new menus and features C3463M B 2 11 Revised manual for version 2 300 software which included the addition of the Auto Tracking menu Pelco the Pelco logo and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco Inc or its affiliates All other product names and services are the property of their respective companies Product specifications and availability are subject to change without notice Copyright 2011 Pelco Inc All rights reserved PELLO by Schneider Electric www pelco com Pelco by Schneider Electric 3500 Pelco Way Clovis California 93612 5699 United States USA amp Canada 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120
98. wing the installation instructions that were shipped with it A Warning Proper eye protection should be worn when using compressed air cans C3463M B 2 11 Specifications 23X MODELS DD423 Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed optical range Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise DD423 X Signal Format Scanning System Image Sensor Effective Pixels Horizontal Resolution Lens Zoom Speed Horizontal Angle of View Focus Maximum Sensitivity at 35 IRE Sync System White Balance Shutter Speed Iris Control Gain Control Video Output Video Signal to Noise C3463M B 2 11 NTSC 2 1 Interlace 1 4 inch progressive scan CCD 768 H X 494 V 540 TV lines 1 6 focal length 3 6 82 8 mm 23X optical zoom 12X digital zoom 2 9 4 2 5 8 seconds 54 at 3 6 mm wide zoom 2 5 at 82 8 mm telephoto zoom Automatic with manual override 0 65 lux at 1 60 sec shutter speed color 0 15 lux at 1 60 sec shutter speed B W Internal AC line lock phase adjustable using remote control V Sync Automatic with manual override Automatic electronic iris manual 1 2 1 30 000 Automatic iris control with manual override Automatic off 1 Vp p 75 ohms gt 50 dB PAL 2 1 Interlace 1 4 inch progressive scan
99. x SWITCH SETTINGS Before installing the dome drive you must configure the receiver address termination and baud setting The DIP switches used to configure these settings are located on the base of the dome drive Figure 1 shows the default settings for the DIP switches Switch SW1 1 SW1 switch 1 is set to the ON position all other switches are set to the OFF position Refer to the following sections to set the address termination and baud settings for the dome drive Figure 1 Default Switch Settings SW1 RECEIVER ADDRESS Set the SW1 switches for the address of the dome drive The following information is required to set the dome drive address Pelco P type control The default address is 2 Refer to Table F on page 64 for address settings that use Pelco P type control The maximum number of receivers is 32 Pelco D type control The default address is 1 Refer to Table G on page 65 for address settings that use Pelco D type control The maximum number of receivers is 254 SW2 SWITCH 1 AD 32 PRESET SYSTEM SW2 1 should be set to the ON position if an AD 32 controller and Pelco s TXB AD translator board are used to control the dome system SW2 SWITCH 2 CM9502 SETTING If a CM9502 matrix system is used with the dome drive set SW2 2 to the ON position SW2 SWITCH 3 CONTROL SYSTEM COMPATIBILITY Coaxial Control Systems Although Spectra IV dom
100. ype cannot be changed Also the Holiday feature cannot be accessed from the Edit Schedule menu For instructions on changing the features in the Edit Schedule menu refer to Edit Event on page 54 C3463M B 2 11 PATTERNS LANGUAGE lt CAMERA gt PATTERN NUMBER lt MOTION gt lt PROGRAM PATTERN gt lt SYSTEM INFORMATION gt AUTO TRACKING lt CLEAR PATTERN gt lt DISPLAY SETUP gt lt EDIT SCHEDULE gt lt POWER UP gt lt DOME SETTINGS gt ACK ALERT LINE SYNC BACK lt PRESETS gt EXIT RESET CAMERA lt PATTERNS gt REFERENCE INFORMATION CYCLE CAMERA POWER lt ZONES gt PATTERN USAGE REBOOT SYSTEM lt WINDOW BLANKING gt REMAINING EXIT lt ALARMS gt lt AUX gt lt TITLE TEXT gt lt ALERT gt lt CLEAR gt lt PASSWORD gt lt CLOCK gt lt EVENT gt BACK EXIT A pattern is a memorized repeating series of pan tilt zoom and preset functions that can be recalled with a command from a controller or automatically by a configured function alarm park event or power up The 23X models have one user defined pattern available The 27X and 35X models can handle up to eight patterns Pattern length is based upon memory usage rather than a fixed amount of time The complexity of a pattern will determine the amount of storage available to configure other patterns NOTE most cases the memory available will allow for ample time to schedule typical patterns If the scheduled patterns are unusually lengt

Download Pdf Manuals

Related Search

Related Contents

Canon MAXIFY iB4020 Quick Guide for Mac  

Copyright © All rights reserved. Failed to retrieve file