Pelco CM9700-SER-32 User's Manual
Contents
1. d After ENTER CURRENT PASSWORD appears on the screen type PELCON and then press the Enter key Using the arrow key scroll down to PCI PLUG AND PLAY SETUP and then press Enter Scroll down to PCI SLOT 2 IRQ PRIORITY Change the setting to 15 by repeatedly pressing the Page Down key Scroll down to PCI SLOT 3 IRO PRIORITY Change the setting to 3 by repeatedly pressing Page Down 7 Pressthe Esc key to return to the BIOS menu C579M A 5 05 8 Scroll down to PERIPHERAL SETTINGS press Enter and then do the following d 8 Scroll down to ONBOARD SERIAL PORT 2 Change the setting to DISABLED by pressing Page Down Press Esc Scroll down to SAVE SETTINGS AND EXIT and type Y Press Enter 9 Reboot machine by pressing Ctrl Alt Del 3 SERCOM CARDS 2 ROCKET PORT CARDS COM 2 AVAILABLE 88 TOTAL PORTS WARNING 579 5 05 Software version 9 03 007 or higher must be installed in the CC1 to enable port expansion ability If running a previous version contact Pelco for software upgrade kit options and availability Failure to turn off the CC1 power could result in serious damage to the equipment Electrostatic discharge ESD precautions must be observed when performing the procedures described in this manual Always wear a gounding strap connected to an approved grounding source when working on or around exposed electronic components Turn off all power to the CC1 Disconnect and label all attach2. 11 Reboot machine by pressing Ctrl Alt Del 579 5 05 3 SERCOM CARDS 3 ROCKET PORT CARDS COM 2 UNAVAILABLE 120 TOTAL PORTS AN WARNING e Software version 9 03 007 or higher must be installed in the CC1 to enable port expansion ability If running a previous version contact Pelco for software upgrade kit options and availability e Failure to turn off the CC1 power could result in serious damage to the equipment e Electrostatic discharge ESD precautions must be observed when performing the procedures described in this manual Always wear gounding strap connected to an approved grounding source when working on or around exposed electronic components 1 Turn off all power to the CC1 Disconnect and label all attached cabling 2 Remove the top cover mounting screws refer to Figure 2 3 From the rear tilt the top cover up at a slight angle and then pull backwards away from the front edge to remove the cover from the CC1 chassis refer to Figure 2 4 Install the RP cards into the CC1 a Remove the screws securing the Sercom card mounting plate refer to Figure 5 b Remove the Sercom card mounting plate by gently pulling outward from the CC1 chassis refer to Figure 5 c Remove the Sercom card from ISA slot 4 by gently pulling up refer to Figure 3 NOTE This configuration mandates that the VGA card be installed in PCI slot 4 If present in any other PCI expansion slot remove the retaining screw and ge
3. c Connect the male end of the remaining data cable to the top DB26 connector of the RP card Connect the other end to the DB25 host connector for the first grouping of 16 ports on the left side of the port expansion unit d If using RS 232 operation set the switch located to the right of each port used on the port expansion unit to the 232 position C579M A 5 05 e Connect peripherals to desired expansion ports Refer to RP1 in Figure 4 RP 1 RP2 125 127 129 131 126 128 130 132 RP3 117 119 121 123 118 120 122 124 H Top connector on rocket card Bottom connector on rocket Figure 4 Rocket Card to Expansion Port Control Association 4 Apply power to the CC1 After applying power press the Delete key on the keyboard to enter into the BIOS menu settings and then do the following a After ENTER CURRENT PASSWORD appears on the screen type PELCON and then press the Enter key b Using the arrow key scroll down to PCI PLUG AND PLAY SETUP and then press Enter c Scroll down to PCI SLOT 2 IRO PRIORITY Change the setting to 15 by repeatedly pressing the Page Down key d Press the Esc key to return to the BIOS menu 5 Scroll down to SAVE SETTINGS AND EXIT and type Y 6 Press Enter 7 Reboot machine by pressing Ctrl Alt Del 579 5 05 7 4 SERCOM CARDS 2 ROCKET PORT CARDS COM 2 UNAVAILABLE 96 TOTAL PORTS WARNING Software version 9 03 007 or higher must be
4. 2 Install the RP card into the CC1 Refer to Figure 2 and Figure 3 and do the following a Remove the top cover mounting screws b From the rear tilt the top cover up at a slight angle and then pull backwards away from the front edge to remove the cover from the CC1 chassis NOTE If the VGA card is present in PCI slot 2 remove the retaining screw and gently pull the card up Reinstall the card into PCI slot 4 follow steps c and d applying them to the VGA card and PCI slot 4 c Remove the retaining screw and slot cover for PCI slot 2 Slide the cover out d Install the RP card into PCI slot 2 Carefully align the gold fingered edge connector of the RP card with the PCI slot Gently but firmly press the RP card down until fully seated into the PCI slot Reinstall the retaining screw to secure the RP card into place 579 5 05 5 e Reinstall the top cover and secure with mounting screws 2 EXPANSION SLOTS Figure 3 CC1 Internal Layout 3 Mount external hardware Refer to Figure 1 and do the following a Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit The data cables are three feet in length b Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1 Connect the other female end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit
5. installed in the CC1 to enable port expansion ability If running a previous version contact Pelco for software upgrade kit options and availability Failure to turn off the CC1 power could result in serious damage to the equipment Electrostatic discharge ESD precautions must be observed when performing the procedures described in this manual Always wear a gounding strap connected to an approved grounding source when working on or around exposed electronic components 1 Turn off all power to the CC1 Disconnect and label all attached cabling 2 Install the RP cards into the CC1 Refer to Figure 2 and Figure 3 and do the following a b Remove the top cover mounting screws From the rear tilt the top cover up at a slight angle and then pull backwards away from the front edge to remove the cover from the CC1 chassis NOTE This configuration mandates that the VGA card be installed in PCI slot 4 If present in any other PCI slot remove the retaining screw and gently pull the card up Reinstall the card into PCI slot 4 follow steps c and d applying them to the VGA card and PCI slot 4 C d Remove the retaining screw and slot cover for PCI slots 2 and 3 Slide both covers out Install an RP card into PCI slot 2 Carefully align the gold fingered edge connector of the RP card with the PCI slot Gently but firmly press the RP card down until fully seated into the PCI slot Reinstall the retaining screw to secure the
6. C1 via the installation of an RP rocket port PCI expansion card A maximum of 120 total ports can be achieved by using three CM9700 SER 32 assemblies in conjunction with the Sercom cards in the CC1 Refer to Figure 1 for assembly detail RS 232 422 SWITCH 32 COMM INTERFACE FOR EACH CONNECTOR IS SET BY THIS PCI EXPANSION CARD 1 SWITCH UP IS RS 422 ROCKET PORT CARD DOWN IS RS 232 HOST CONNECTIONS y CM9700 ADP 120 CONNECTING DATA CABLE 2 ADAPTER BRACKET ONE SET OF CONNECTING DATA FOR USE WITH RP CARD CABLES IS PROVIDED EACH IN PCI SLOT 1 CABLE IS THREE FEET LONG ADAPTER DB25 TO RJ 45 32 Figure 1 CM9700 SER 32 Assembly Detail 4 SERCOM CARDS 1 ROCKET PORT CARD 64 TOTAL PORTS WARNINGS e Software version 9 03 007 or higher must be installed in the CC1 to enable port expansion ability If running a previous version contact Pelco for software upgrade kit options and availability e Failure to turn off the CC1 power could result in serious damage to the equipment e Electrostatic discharge ESD precautions must be observed when performing the procedures described in this manual Always wear a gounding strap connected to an approved grounding source when working on or around exposed electronic components 1 Turn off all power to the CC1 Disconnect and label all attached cabling
7. INSTALLATION OPERATION CM9700 SER 32 Port Expander C579M A 5 05 Contents Regulatory NOTICES ose rette zer d Denier DU Vane DOR SO ake seas hae ete ahs Deuce DUC DORT ged de 4 5 4 Sercom Cards 1 Rocket Port 64 Total Ports RR e 5 4 Sercom Cards 2 Rocket Port Cards Com 2 Unavailable 96 Total Ports I CC I 8 3 Sercom Cards 2 Rocket Port Cards Com 2 Available 88 Total Ports 9 3 Sercom Cards 3 Rocket Port Cards Com 2 Unavailable 120 Total Ports nonno I I I I I I IC I eee eee eee 12 List of Illustrations 579 5 05 9700 5 32 Assembly Detail e e e ea 5 Removing the COT Top COVE ss ert eee pepe 4 6 CC1 Internal Layout I I I I e e e n e e hes 6 Rocket Card to Expansion Port Control Association 2 20 00 7 Sercom Card Mounting Plate Removal o n 10 Sercom PCI Card Configuration for 88 Ports Com 2 Available cece ene eee 10 CM9700 ADP 120 Adapter Plate Installation cesses he kr emn ne eh e da a qe Re 11 Sercom PCI Card Configuration for 120 Ports Com 2 Unavailable I I I Re 12 3 Regulatory Notices This device complies w
8. RP card into place Repeat step d for installing the second RP card into PCI slot 3 3 Reinstall the top cover and secure with mounting screws 4 Mount external hardware Refer to Figure 1 and do the following NOTE This procedure is for each individual port expansion assembly one RP card and port expansion unit and is to be duplicated for each RP card installed in the CM9700 CC1 Power should not be applied until all physical connections have been secured a b d 5 Connect peripherals to desired expansion ports Refer to RP1 and RP2 in Figure 4 Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit The data cables are three feet in length Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1 Connect the other female end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit Connect the male end of the remaining data cable to the top DB26 connector of the RP card Connect the other end to the DB25 host connector for the first grouping of 16 ports on the left side of the port expansion unit If using RS 232 operation set the switch located to the right of each port used on the port expansion unit to the 232 position 6 Apply power to the CC1 After applying power press the Delete key on the keyboard to enter into the BIOS menu settings and then do the following b
9. Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Changed 9760 reference to CM9700 Manual updated to include CM9700 ADP 120 adapter plate and revised installation instructions Copyright 2005 Pelco All rights reserved PELLO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
10. T 3 IRQ PRIORITY Change the setting to 3 by repeatedly pressing Page Down Press the Esc key to return to the BIOS menu Scroll down to PERIPH 8 b 0 ERAL SETTINGS press Enter and then do the following Scroll down to ONBOARD SERIAL PORT 2 Change the setti Press Esc Scroll down to S Press Enter ng to DISABLED by pressing Page Down AVE SETTINGS AND EXIT and type Y Reboot machine by pressing Ctrl Alt Del C579M A 5 05 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series ixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video
11. ate REVISION HISTORY Manual Date Comments C579M 8 02 Original version C579M A 5 05 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number and provide the following information 1 Model and serial number 2 Date of shipment number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto
12. e been secured a Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit The data cables are three feet in length b Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1 Connect the other female end 0 the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit Connect the male end of the remaining data cable to the top DB26 connector of the RP card Connect the other end to the DB25 host connector for the first grouping of 16 ports on the left side of the port expansion unit d If using RS 232 operation set the switch located to the right of each port used on the port expansion unit to the 232 position 8 Connect peripherals to desired expansion ports Refer to RP1 and RP2 in Figure 4 9 Apply power to the CC1 After applying power press the Delete key on the keyboard to enter into the BIOS menu settings and then do the following a Afte r ENTER CURRENT PASSWORD appears on the screen type PELCON and then press the Enter key b Using the arrow key scroll down to PCI PLUG AND PLAY SETUP and then press Enter c Scroll down to PCI SLOT 1 IRQ PRIORITY Change the setting to 5 by repeatedly pressing the Page Down key d Scroll down to PCI SLOT 2 IRQ PRIORITY Change the setting to 15 by repeatedly pressing Page Down 10 Pressthe Esc key to return to the BIOS menu
13. ed cabling Remove the top cover mounting screws refer to Figure 2 From the rear tilt the top cover up at a slight angle and then pull backwards away from the front edge to remove the cover from the CC1 chassis refer to Figure 2 Install the RP cards into the CC1 d b Remove the screws securing the Sercom card mounting plate refer to Figure 5 Remove the Sercom card mounting plate by gently pulling outward from the CC1 chassis refer to Figure 5 Remove the Sercom card from ISA slot 4 by gently pulling up refer to Figure 3 This card will not be used and should be stored in an ESD safe container iB Hr egi pe Rege CA d hd BB ZEZAM Tode eie a L Figure 5 Sercom Card Mounting Plate Removal NOTE If the VGA card is present in PCI slot 2 remove the retaining screw and gently pull the card up Reinstall the card into PCI slot 4 follow steps d e and f applying them to the VGA card and PCI slot 4 d Remove the retaining screw and slot cover for PCI slot 2 Slide the cover out e Install an RP card into PCI slot 1 Carefully align the gold fingered edge connector of the RP card with the PCI slot Gen
14. ith Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission s rules This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada C579M A 5 05 Installation The CM9700 SER 32 port expander assembly increases by 32 the number of available Sercom serial communication ports in a node based CM9700 C
15. ntly pull the card up Reinstall the card into PCI slot 4 follow steps d e and f applying them to the VGA card and PCI slot 4 d Remove the retaining screw and slot cover for PCI slot 2 and 3 Slide both covers out e Install an RP card into PCI slot 1 Carefully align the gold fingered edge connector of the RP card with the PCI slot Gently but firmly press RP card down until fully seated into the PCI slot f Repeat step e for installing the second and third RP cards into PCI slots 2 and 3 Reinstall the retaining screws to secure these RP cards into place 1C ES e VGA CARD 2 3 A A 4 RP CARDS SERCOM CARDS Figure 8 Sercom PCI Card Configuration for 120 Ports Com 2 Unavailable 5 Install the CM9700 ADP 120 adapter plate Carefully align the plate with the front of the three Sercom cards and the RP card in PCI slot 1 while pushing in toward the CC1 chassis Secure with mounting plate screws removed earlier Refer to Figure 7 6 Reinstall the top cover and secure with mounting screws C579M A 5 05 7 Mount external hardware Refer to Figure 1 and do the following NOTE This procedure is for each individual port expansion assembly one RP card and port expansion unit and is to be duplicated for each RP card installed in 579 5 05 Connect peripherals to desired expansion port
16. recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to st
17. s Refer to RP1 RP2 and RP3 in Figure 4 the CM9700 CC1 Power should not be applied until all physical connections have been secured Mount the port expansion unit so that the two supplied data cables will reach the CC1 unit The data cables are three feet in length Connect the male end of one data cable to the bottom DB26 connector of the RP card installed in the CC1 Connect the other female end to the DB25 host connector for the second grouping of 16 ports on the right side of the port expansion unit Connect the male end of the remaining data cable to the top DB26 connector of the RP card Connect the other end to the DB25 host connector for the first grouping of 16 ports on the left side of the port expansion unit If using RS 232 operation set the switch located to the right of each port used on the port expansion unit to the 232 position Apply power to the CC1 After applying power press the Delete key on the keyboard to enter into the BIOS menu settings and then do the After ENTER CURRENT PASSWORD appears on the screen type PELCON and then press the Enter key following b Using the arrow Scroll down to P d Scroll down to P Scroll down to P key scroll down to PCI PLUG AND PLAY SETUP and then press Enter CI SLOT 1 IRQ PRIORITY Change the setting to 5 by repeatedly pressing the Page Down key CI SLOT 2 IRO PRIORITY Change the setting to 15 by repeatedly pressing Page Down CI SLO
18. tly but firmly press the RP card down until fully seated into the PCI slot f Repeat step e for installing the second RP card into PCI slot 2 Reinstall the retaining screw to secure the RP card into place IC M 4 VGA CARD RP CARDS SERCOM CARDS Figure 6 Card Configuration for 88 Ports Com 2 Available 5 Install the CM9700 ADP 120 adapter plate Carefully align the plate with the front of the three Sercom cards and the RP card in PCI slot 1 while pushing in toward the CC1 chassis Secure with mounting plate screws removed earlier Refer to Figure 7 C579M A 5 05 6 Reinstall 0 0 BE o gt m 9 FANE Figure 7 CM9700 ADP 120 Adapter Plate Installation the top cover and secure with mounting screws 7 Mount external hardware Refer to Figure 1 and do the following NOTE This pr ocedure is for each individual port expansion assembly one RP card and port expansion unit and is to be duplicated for each RP card installed in the CM9700 CC1 Power should not be applied until all physical connections hav
Download Pdf Manuals
Related Search