Pelco SS2000 User's Manual
Contents
1. MOUNT STRUCTURAL CEILING MOUNTING DROP CEILING MOUNTING WALL MOUNTING Figure 8 Mounting Configurations Pelco Manual C429M B 2 98 11 3 4 DOME INSTALLATION NOTE small hole in the upper dome for safety chain attachment should be positioned at the back con nector end of the camera NOTE For SS20 SS22 mounting re fer to steps 1 2 6 7 8 and 10 For step 9 adjust the tilt and rotation and tighten all hardware 12 To install your dome system perform the following steps refer to Figure 9 1 10 11 Select the appropriate pipe length and mounting method If the MRCA mount is used tighten the pipe to approximately 30 ft Ib then tighten the 8 32 screw in the pipe nut to lock the pipe threads Slide the upper dome onto the pipe and lock it out of the way with a suitable retainer Screw the mounting flange item 4 onto the pipe and tighten securely ap proximately 20 ft Ib Tighten the 8 32 screw in the pipe nut to lock the pipe threads Align the three hole pattern in the pan spindle with the holes in the lower bracket item 5 and attach with 1 4 20 x 5 8 hex head bolts and lock wash ers provided Tighten firmly Attach the upper drive bracket item 3 to the bottom spindle side of the pan tilt using four 4 8 32 x 1 2 pan head screws and lock washers provided Refer to Figure 9 for proper orientation Connect the instal2. PCB3000100 COMMON BLK W RED NON SL ONLY TO CAMERA VIDEO VIDEO OUT VIO SHIELD SAFETY GND TO CAMERA CAM AC IRIS FOCUS ZOOM LENS COMM 206705 1 PRESET HIGH W GRN BLK pan poy pend ba PRESET COMM W BRN BLK SPARE W ORG BLK LENS PRESET ZOOM W RED BLK LENS PRESET FOCUS 21 W YEL BLK PAN PRESET 24 W GRY SL ONLY TILT PRESET 23 VIO PAN 22 4000008 900000014 1500000020 2100000 25 26000 28 2 0 4 20004000COMP CON205840 3 Figure 4 SS2000SL PP Wiring Diagram 8 Pelco Manual C429M B 2 98 3 2 CONNECTOR ASSEMBLY NOTE Contacts cannot be removed To install and test the 552000 552002 Series dome you will need to assemble the from the connector without the use connector parts provided Fabricate the interconnecting cable as outlined below of an AMP extraction tool part num see Figure 5 ber 27305183 for 9 14 or 16 pin connector or ZT91067 2 for 28 pin 1 Slide the cable clamp part A item 1 over the cable with the threaded end S rs facing the connector item 5 connector which is available from aging Pelco 2 Ifthe cable has a diameter less than 1 2 inch 1 3 cm slide the rubber boot item 2 over the end of the cable and press inside the cable clamp to form a good seal 3 Strip back the cable jacket approximately 1 1 4 inches 3 2 cm and separate the individual conductors 4
3. Pelco Manual C429M B 2 98 7 0 SPECIFICATIONS ELECTRICAL Input Voltage 24 VAC required for pan tilt Running Current Pan 0 31 amp 7 44 vA Tilt 0 38 amp 9 12 vA Connectors Pan Tilt Amp CPC type mate supplied Lens Hirschmann MAB6100 Video BNC Camera Power Spade lugs Motors Two phase induction type instantaneous reversing Limit Switches Pan 5 amp external adjustment Tilt 5 amp external adjustment Conductor Requirements as listed plus coax cable Non PP models Pan tilt 5 plus ground Lens 4 Camera AC 2 PP models Pan tilt 9 plus ground Lens 6 Camera AC 2 MECHANICAL Pan 0 355 movement in horizontal plane Models 552000 SS2000 PP 360 continuous rotation Models SS2000 SL SS2000SL PP Pan Speed 24 sec 1 no load condition Tilt 90 from horizontal plane Tilt Speed 12 sec 5 no load condition Maximum Load 10 Ib 4 6 kg Gearing Chain and direct drive Bearings Pan Heavy duty ball bearing and Oilite bronze bushing Tilt Oilite bronze bushing Braking Friction Pelco Manual C429M B 2 98 17 18 GENERAL Maximum Camera Lens Length Ambient Temperature Range Construction Upper dome Lower dome Dimensions Weight Model SS20 SS22 All other models Shipping Weight Model SS20 SS22 other models 12 5 inches 31 75 cm 35 F to 120 F 1 6 C to 48 8 Black high impact plastic ABS Acrylic hemisphere w
4. Interior Surface Chrome The inside surface of a chrome dome is easily scratched Use the following precautions to maintain the dome s surface a b Always handle the dome from the outside of its circular flange Never touch the coated inside surface The acid in your fingerprints will even tually etch the coating if the fingerprints are not carefully removed according to the recommended cleaning procedure in item e If dust or other contaminants accumulate on the dome s interior remove the debris with compressed air Compressed air cans are available from photo graphic equipment or electronic supply dealers If heavy residue accumulates and cannot be removed with air pressure rinse with water and immediately dry with air pressure so that water spots will not remain Avoid wiping the coated surface with direct hand pressure it will eas ily abrade unless extreme care is taken Once scratched the dome cannot be recoated If internal wiping is necessary avoid hand rubbing Instead make a wick as follows Use a very soft paper towel Roll a section into a tightly wound tube Tear the tube in half and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with water Hold the dome with its opening facing downward and wipe the interior of the dome with the wet end of the wick Use a circular motion starting from the outside and spiraling into the center Use a new wick for each two passes over the dome
5. PELCO SS20 SS22 SS2000 SS2002 Series Discreet Surveillance Enclosures Installation Operation Manual C429M B 2 98 LISTED Pelco 300 W Pontiac Way Clovis e CA 93612 5699 USA Pelco Online 9 http www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 DataFAX 1 559 292 0435 CONTENTS Section 1 0 GENERAL 1 1 IMPORTANT SAFEGUARDS AND WARNINGS 2 0 DESCRIPTION titre eere ettet 4 23 MODELS eee ER HR e e d n ace Al inl eta 4 3 0 INSTALLATION n D e REPRE PUER 5 3 14 CONDUCTOR AND CABLE REQUIREMENTS AD 3 1 1 Recommended Mounts aO 3 1 2Recommended Cables 445 3 2 CONNECTOR ASSEMBLY essere 9 3 9 MOUNITING bee Fo EC rH E 11 3 4 DOME INSTALLATION eeeeneeeeeeneeneenennennee nnne nnns 12 4 0 EXPLODED ASSEMBLY DIAGRAM eese 13 5 0 ADJUSTMENTS iih OH RH BRNO eH e 15 6 0 MAINTENANCE t e re PA Pe E 16 0 SPECIFICATIONS o GARE 17 8 0 WARRANTY AND RETURN INFORMATION 20 LIST OF ILLUSTRATIONS Figure Page 1 5520 5522 552000 552002 Dimension Drawing 4 2 S2000 SS2000 SL SS2002 SL Wiring Diagram 6 3 SS2000
6. continuous pan rotation S2002 SL Same as SS2000 SL except supplied with a 14 chrome opaque lower dome with 2 f stop light loss SS2000SL PP Same as SS2000 PP except supplied with 360 continuous pan rotation 14 00 35 56 18 00 45 72 NOTE VALUES IN PARENTHESIS ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 1 SS20 SS22 SS2000 SS2002 Dimension Drawing 4 Pelco Manual C429M B 2 98 3 0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned for credit or repair 3 1 CONDUCTOR AND CABLE REQUIREMENTS NOTE following are cable re quirements A relay box RB24 is available to extend the operating dis tance up to 13 000 feet 3 962 m over 16 Awg wire 3 1 1 3 1 2 Pelco Manual 429 2 98 A minimum of 11 conductors plus coax is required which includes common re quirements for motorized zoom lens and camera AC power Non PP Models 11 Conductor 12 Conductor 18 Awg 227 ft 82m 494 ft 150 m 16 Awg 432 ft 131 m 785 ft 239 m 14 Awg 690 ft 210 m 1 253 ft 381 m PP Models 17 Conductor 18 Conductor 18 Awg 227 ft 82m 494 ft 150 m 16 Awg 432 ft 131 m 785 ft 239 m 14 Awg 690 ft 210 m 1 253 ft 381 m Using 2 conductors for common Calculations are based on a 10 cable loss with both motors running Recommended Mounts MRWA Wall mount adapter MRCA Ceiling mount adapter Recommended Cables C1906 Pretest
7. 1 1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Only use replacement parts recommended by Pelco After replacement repair of this unit s electrical components conduct a resis tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The installation method and materials should be capable of supporting four times the weight of the enclosure pan tilt camera and lens combination The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit maintenance instructions in the literature accompanying this This symbol indicates that there are important operating and unit CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please thoroughly familiarize yourself with the information in this manual prior to installation and
8. SHIELD COAX VIDEO YELLOW ORANGE BLUE GREEN WHITE AC HIGH CAMERA BLACK IRIS FRONT VIEW TAN OR BLK WHT FOCUS 14 PIN CONNECTOR PINK OR RED WHT ZOOM VIOLET COMMON LENS GRAY AC LOW CAMERA Figure 6 Mating Cable Assembly Configuration non PP Versions CABLE 12 COND 6 WIR201912 1 CABLE 9 COND 6 E WIR220709 COAX Q 6 28 POS RECEPTACLE CRIMP SOCKET WIRRG174 U 1 66504 0 CABLE CLAMP RES CON206070 1 BROWN COMMON PAN AND TILT CORE COAX VIDEO RED LEFT BLUE HIGH PRESET SHIELD COAX VIDEO BROWN COMMON PRESET YELLOW WHT ORG BLK SPARE ORANGE RED ZOOM PRESET BLUE YELLOW FOCUS PRESET GREEN GROUND BLACK PAN PRESET WHITE AC HIGH CAMERA VIOLET TILT PRESET BLACK IRIS WHITE PAN PRESET SL only TAN OR BLK WHT FOCUS FRONT VIEW PINK OR RED WHT ZOOM 28 PIN CONNECTOR VIOLET COMMON LENS GRAY AC LOW CAMERA 12 Cable 9 Conductor Cable Figure 7 Mating Cable Assembly Configuration PP Versions 10 Pelco Manual C429M B 2 98 3 3 MOUNTING The 552000 552002 enclosure is designed to be suspended from a suitable length of 1 1 2 pipe threaded at both ends This pipe can be interfaced to either a Pelco MRWA wall adapter MRCA ceiling adapter or coupled to a longer length of pipe Refer to Figure 8 for mounting configurations CEILING 77 MOUNT TEE UNION 7
9. PP Wiring Diagram 2 7 4 SS2000SL PP Wiring Diagram 8 5 Connector Assembly visirani aie aeiy iiaii 9 6 Mating Cable Assembly Configuration non PP Versions 10 7 Mating Cable Assembly Configuration PP Versions 10 8 Mounting Configurations 11 9 552000 552002 Exploded Assembly Diagram 14 10 EimitStop Eoc tions n nae EC deep tede 15 11 Tilt Limit Stop Modifications 2 15 LIST OF TABLES Table Page A 552000 552002 Exploded Assembly Diagram 13 REVISION HISTORY Manual Date Comments C429M A 10 94 Wire colors revised on figures 2 4 6 and 7 Pin 8 Figure 2 Pins 8 amp 23 Figures 3 and 4 Pins 8 11 12 13 Figures 6 and 7 C429M B 7 96 Revised to include new models SS22 and SS2002 SL 8 96 Revised Section 5 0 Mechanical Parts List regarding lower dome part numbers and quantities of velcro 7 97 Corrected wiring for pins 19 and 27 in Figure 7 per ECO 97 235 2 98 Revised Section 6 0 Maintenance Changed manual to new style 2 Pelco Manual C429M B 2 98 1 0 GENERAL CAUTION This device is VAN designed to operate at 24 volts AC power Input volt ages must not exceed 28 volts or drop below 22 volts or else damage the the motors will occur Should you need technical assis tance please call 800 289 9100
10. operation Pelco Manual 429 2 98 2 0 DESCRIPTION Pelco s SS20 SS22 SS2000 SS2002 Series domes are full sphere discreet sur veillance enclosures designed to be suspended from ceilings and to compliment the interior design of businesses hotels and offices The black opaque or chrome lower dome effectively camouflages a CTTV security surveillance system without compromising the quality of the video picture Options for the SS2000 SS2002 include a standard pan tilt pan tilt with continuous 360 pan rotation SL or preset pan tilt available in either the standard or SL ver sion pan tilt All pan tilts are pre wired for all system functions dramatically reduc ing installation time The use of standard manufactured components increases the reliability and serviceability of the system 2 1 MODELS SS20 Full sphere discreet surveillance dome with fixed mount for CCD type cameras 14 black opaque lower dome with 1 f stop light loss 5522 Same as 5520 except supplied with a 14 chrome opaque lower dome with 2 f stop light loss SS2000 Full sphere discreet surveillance dome with high speed integral pan tilt for CCD type cameras 14 black opaque lower dome with 1 f stop light loss SS2000 PP Full sphere discreet surveillance dome with high speed integral pan tilt with presets PP option for CCD type cameras 14 black opaque lower dome with 1 f stop light loss S2000 SL Same as SS2000 except supplied with 360
11. The contact pins supplied with the mating connector are the crimp type which may also be soldered if you so desire 5 After crimping or soldering the contacts push them into the proper holes in the connector until they snap in place 6 Slide part A of the cable clamp toward the connector and screw the parts together Attach part B item 1 onto part A and connect both parts with the Screws provided 7 Connect the cable assembly to the unit and seat the connector by twisting the locking collar until it snaps into position 8 For ease of installation a mating cable assembly is supplied with the domes to extend the cable from the pan tilt Please refer to Figures 6 and 7 for wiring pin locations and color codes bo Pn a INSULATION mer OUTSIDE JACKET OF CABLE CABLE CLAMP 10008 4000008 RUBBER BOOT 900000014 1500000020 21000 O O25 CABLE 2600 O28 CRIMP PIN FRONT VIEW FRONT VIEW CABLE PLUG 14 OR 28 POSITION 14 PIN CONNECTOR 28 PIN CONNECTOR Figure 5 Connector Assembly Pelco Manual 429 2 98 9 CABLE 12 COND 9 6 WIR201912 COAXQ 8 ci WIRRG59 U9259 CONCP88 2 14 POS RECEPTACLE CRIMP SOCKET CABLE CLAMP CON206403 3 CON66105 2 CON206070 1 POSITION FUNCTION BROWN COMMON PAN AND TILT CORE COAX VIDEO RED LEFT
12. c Way Clovis CA 93612 5699 Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair Goods returned for repair or credit should be clearly identified with the assigned CA RA number and freight should be prepaid All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Ship freight prepaid to Pelco 300 West Pontiac Way Clovis CA 93612 5699 Pelco Manual C429M B 2 98
13. ed 6 foot cable with video coax C1925 Pretested 25 foot cable with video coax COoMMOon LEFT FRONT YIEW VIDEO VIDEO SHIELD C AMER 4 24 VAC WFYI Ww BLK WHITE lt 42 LENS CONNECTOR IRIS FOCUS LENS COMMON SAFETY GROUND INPUT CONNECTOR DESCRIPTION MANUFACTURER FART NUMBER 1 CAPACITOR 15 MFD 100 SPRAGUE ___ CAPUDDTS D 100N 1 cz CAPACITOR 15 1009 SPRAGUE CAPUDOTS O TO0N NNI 1r 1 J2 CONNECTOR HIRSCHMANN CONMABE1O0 Tig EONMEETORFINS E0NG6102 7 1 meur conecto ame tomznesus i MATING CONNECTOR ASSY AME 551000 5 actuator MICROSWITCH Swhistsen 1 MATING CONNECTOR HIRSCHMANN 56100 Figure 2 SS2000 SS2000 SL SS2002 SL Wiring Diagram 6 Pelco Manual C429M B 2 98 PCB3000100 COMMON BLK W RED NON SL ONLY TO CAMERA VIDEO OUT a TO CAMERA VIDEO VIO SHIELD SAFETY GND CAM AC CAM AC IRIS FOCUS ZOOM LENS COMM 206705 1 PRESET HIGH W GRN BLK PRESET COMM W BRN BLK 1 W ORG BLK LENS PRESET ZOOM W RED BLK 277 LENS PRESET FOCUS W YEL BLK bad W GRY TILT PRESET VIO PAN PRESET GRY 4000008 900000014 1500000020 2100000 25 26000 28 20004000COMP CON205840 3 Figure 3 SS2000 PP Wiring Diagram Pelco Manual C429M B 2 98 7
14. ety SB2511000 Pan tilt assembly PT2500 Fixed mount assembly Model SS20 only S20001001ASSY Cable assembly 14 pin x 6 For SS2000 and SS2000 SL SS1000ASSY Cable assembly 28 pin x 6 552000 and SS2000SL PP SS1001ASSY Pipe mounting 5534002 Snap for safety chain not shown SB2511001 Part number is for the dome only To order a complete lower dome assembly specify the part numbers S820004300COMP black and SS20200COMP chrome These part numbers include items 2 7 8 and 12 Pelco Manual C429M B 2 98 13 1 1 2 NPT PIPE INSTALLATION CABLE PIPE NUT MOUNTING COLUMN 11 UPPER DOME 1 PT2500 SERIES PAN TILT SAFETY CHAIN LOWER DOME Figure 9 552000 552002 Exploded Assembly Diagram 14 Pelco Manual C429M B 2 98 5 0 ADJ USTMENTS To adjust the pan tilt limits perform the following steps Refer to Figure 10 for limit stop locations CAUTION Do not attempt Factory pan limits are set to 0 355 and tilt limits are set to 0 90 horizontal to to adjust limit stops when vertical Under normal conditions the tilt limits should not have to be reset To the pan tilt is in operation adjust limit stops perform the following steps Damage to the equipment can result Do not operate equipment without limit 1 Panto the right using the joystick control until the desired pan limit is reached Adjust the pan limit stop until the actuator clicks Lock the l
15. imit into position stops SL models are sup 2 to the desired left position adjust the pan limit stop until the actuator plied without pan limit stops clicks and lock into position therefore no adjustments are necessary Pan to the left and right to verify exact positioning and tighten both stops se curely 4 limit is designed to allow for 0 90 travel horizontal to vertical The tilt can be adjusted to any point between horizontal and vertical but must never exceed these boundaries 5 To alter the factory set tilt limit bend the actuator stops on the micro switches Move the tilt table to the desired position and adjust the actuators until the Switch clicks lock into position see Figure 11 6 Tilt up and down to verify exact positioning LIMIT STOP FIXED LIMIT STOP RIGHT LIMIT ACTUATOR LIMIT STOP LEFT LIMIT ACTUATOR LOCKING SCREW Figure 10 Limit Stop Locations Figure 11 Tilt Limit Stop Modifications Pelco Manual C429M B 2 98 15 6 0 MAINTENANCE 16 Clean the acrylic lower dome as necessary to maintain a clear picture Be careful not to scratch the surfaces of the dome Exterior Surface Clean the dome s exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic plastic Either liquid or spray cleaner wax suitable for fine furniture is acceptable Interior Surface Except Chrome Clean the same as the exterior surface
16. ith distortion free viewing window with light attenuation factor of 1 f stop model SS2002 SL has 2 f stop light attenuation factor Rotates with pan tilt and camera lens See Figure 1 7 lb 14 Ib 13 oz 8 Ib 17 Ib Design and product specifications subject to change without notice Pelco Manual C429M B 2 98 NOTES Pelco Manual C429M B 2 98 19 8 0 WARRANTY AND RETURN INFORMATION G Pelco and the Pelco logo are registered trademarks of Pelco Copyright 1998 Pelco All rights reserved 20 WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Excep tions to this warranty are as noted below Three years on Genex Series multiplexers Two years on all standard motorized and fixed focal length lenses e Two years on Legacy Intercept PV1000 Series CM6700 CM8500 CM9500 CM9750 CM9760 Matrix Spectra DF5 Series and DF8 Fixed Dome products Two years WW5700 series window wiper excluding wiper blades e Two years on cameras Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warranty all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis Ca
17. lation cable to the pan tilt and feed it through the center of the 1 1 2 pipe Pull the cable and connector back up into the pipe so that it does not get caught on the rotating parts Assemble the lower bracket and pan tilt to the mounting flange item 4 using 1 4 x 5 8 hex head bolts and flat washers Install the camera lens assembly onto the tilt table of the pan tilt Connect the proper cables Remove the retainer from the upper dome and lower it until it seats itself on the drive bracket Turn the system ON and rotate the pan tilt Check for cable interference Tilt the camera up and down and check for clearance of all moving parts After all tests have been done and the system is functioning properly attach the safety chain to the upper dome with the fasteners provided Install the lower dome and align the viewing window Check for sufficient clearance between the lens and the lower dome Pelco Manual C429M B 2 98 4 0 EXPLODED ASSEMBLY DIAGRAM Table 552000 552002 Exploded Assembly Diagram Dome upper 55200010000 Dome lower Black Opaque S200010001 Dome lower Chrome Opaque S2012000 Bracket drive S20004007COMP Bracket upper 20001000 Bracket lower 5520004008 Velcro black 5 8 wide x inch not shown TV10002 Velcro black 5 8 wide x inch not shown 8822 amp SS2002 SL TV10003 Velcro black 5 8 wide x inch not shown 5520 amp SS2000 Series TV10003 Chain saf
18. lifornia Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss result ing from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Ship freight prepaid to Pelco 300 West Pontia
Download Pdf Manuals
Related Search