Pelco EH1512MT User's Manual
Contents
1. EH1512 Series enclosure Screw 1 4 20 x 3 8 inch Phillips Washer 1 4 inch split lock Screws M6 x 1 0 P x 12 mm hex socket cap Washers 6 mm split lock Gland and nut PG9 cable Gland and nut PG11 cable Wire tie 4 inch EH1512 1 and EH1512 3 only Installation manual EM1512 mount optional 551512 sun shroud optional cl CNG SHIPPING BOX MOUNT 1EA OPTIONAL Figure 1 Package Contents EH1512 ENCLOSURE 1 EA G 1 4 INCH GLANDS AND NUTS SPLIT 2 EA WASHER 1 EA SUN SHROUD 1 EA OPTIONAL C3453M C 5 09 Installation INSTALLING THE OPTIONAL SECURITY KIT The optional security kit EH SKIT contains three tamper resistant screws and a 1 8 inch hollow screwdriver bit To install the security kit 1 Usea 5 mm Allen wrench not supplied to remove the three 10 24 x 0 75 inch hex head screws factory installed that are located on the enclosure base Refer to Figure 2 2 Insert the three tamper resistant screws in the bottom of the enclosure 3 Tighten the screws using the 1 8 inch hollow screwdriver bit supplied Ensure that the gasket is properly sealed INSTALLING THE CAMERA AND MOUNT To install the enclosure camera and lens 1 Usea 5 mm Allen wrench not supplied to loosen the three 10 24 x 0 75 inch hex head screws factory installed that are located on the enclosure base If the security kit is installed use the 1 8 inch hollow screwdriver bit supplied w2. by Schneider Electric INSTALLATION EH1512 Series Enclosures EH1512 Enclosure with EM1512 Mount C3453M C 5 09 Contents Important Safety INStrUctlans e tede pee idu qu ranged ede WE DIU Pe 3 D GSCEIDTIOTIS iie e bono te e e e b e tek x pee e eis doe eth et 4 Models 5662 HM REC PEE 4 Optional AGCeSsOrl6S PRA qnse Up De dones dione fend aa 5 Package Contents rera feat Rae px ER TR E RN 6 Installation ss usc n c eet S deser DUREE Pe USER E 7 Istallirig the Dptional aecutity aed tp eee ug otto vog da ens Lodo 7 Installing eget Me NU TA KU qu fue 7 istallo the Sut ShfOLld Ps pb EEUU tene et SDN d iade e le MA tae fretta dis bad 11 Maintenance sos sce Tc 12 SPECIFICATIONS x en rtt e e b oe e cet bl t ene edere deste ad teg e tt sy tog uo e tres 13 2 C3453M C 5 09 Important Safety Instructions 20 21 22 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus
3. including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one blade wider than the other A grounding plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the points where they exit from the apparatus Only use attachments accessories specified by the manufacturer Only use with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Unplug the apparatus during lightning storms or when unused for long periods of time Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus WARNING To reduce the risk of fire or electr
4. installation and when camera and lens adjustments are necessary Power and video cabling is brought into the enclosure through two adjustable glands PG9 and PG11 on the bottom of the enclosure allowing for easy installation Field installed options include a heater blower or blower with a 24 VAC camera power supply and sun shroud The enclosures can also be ordered from the factory with a 24 VAC 120 VAC or 230 VAC heater blower or blower with a 24 VAC camera power supply If your enclosure has a thermostatically controlled heater the thermostat is set to turn on at 50 F 10 C and turn off at 80 F 27 C The blower operates continuously An optional security kit that prevents opening the enclosure is available NOTE A metric Allen wrench 5 mm and a Phillips screwdriver are required for installation but are not included A flat head screwdriver might also be needed for all models except the EH1512 and EH1512MT The Allen wrench is needed to secure the enclosure to all mounts It is also needed to open and close the enclosure and to secure the pan tilt swivel head on the EM1512 mount MODELS EH1512 Enclosure indoor outdoor EH1512MT Same as EH1512 with an EM1512 feedthrough wall mount EH1512 1 Same as EH1512 with a 120 VAC heater blower with 24 VAC camera power includes the 4 inch wire tie 12 W enclosure power consumption 25 W maximum power consumption capacity EH1512 2 Same as
5. 1512 sun shroud 12 W enclosure power consumption 25 W maximum power consumption capacity Enclosure power consumption does not include camera wattage C3453M C 5 09 OPTIONAL ACCESSORIES Blower Kit EH1512 1BKIT 1512 2 EH1512 3BKIT Heater Blower Kit H1512 1HBKIT H1512 2HBKIT H1512 3HBKIT rn mm Continuous duty 120 VAC 1 W 1 45 cfm Continuous duty 24 VAC 1 W 1 45 cfm Continuous duty 230 VAC 1 W 1 45 cfm 120 VAC 11 W 1 45 cfm 24 VAC 11 W 1 45 cfm 230 VAC 11 W 1 45 cfm NOTE Heaters are thermostatically controlled to turn on at 50 F 10 C and turn off at 80 F 27 C The blower operates continuously Sun Shroud Marine Kit Security Kit Wall Mount C3453M C 5 09 551512 EH MKIT requires EM1512 or EM1450 wall mount EH SKIT for EH1512 three tamper resistant screws and one 1 8 inch hollow screwdriver bit 1512 with feedthrough for EH1512 tilt angle of 20 to 70 sustains wind velocity up to 90 mph PACKAGE CONTENTS NOTE A metric Allen wrench 5 mm is required for installation but is not included A Phillips screwdriver flat head screwdriver or 1 4 inch nut driver is needed for the EH1512 1 and EH1512 3 only The Allen wrench is needed to open and close the enclosure and to secure the enclosure to all mounts It is also needed to secure the pan tilt swivel head on the EM1512 mount The following items are supplied Oty Description
6. C LOW NEUTRAL INPUT AC HIGH PP CAMERA CAMERA OUTPUT AC LOW NEUTRAL CAMERA OUTPUT AC HIGH 230 VAC MODEL WIRING 24 VAC CAMERA OUTPUT 24 VAC CAMERA OUTPUT HIGH LOW ACIN AC OUT NT HI NT INPUT AC HIGH INPUT AC LOW NEUTRAL ZIP TIE HERE 0 GROUND BOSS 230 VAC CAMERA OUTPUT LOW NEUTRAL 230 VAC OUTPUT HIGH Figure 5 EH1512 Wiring Diagram 10 C3453M C 5 09 INSTALLING THE SUN SHROUD The optional sun shroud fits over the top of the EH1512 enclosure Perform the following steps to install the sun shroud 1 Position the front of the sun shroud above the front of the enclosure 2 Press the sun shroud down and against the enclosure until the sun shroud snaps into place Table A Allowable Cable Diameter Gland Cable Diameter PG9 0 181 inch to 0 312 inch PG11 0 230 inch to 0 395 inch NOTE Conduit must be used if the cable diameter is greater than 0 395 inches 1 00 cm RG11 coaxial might be greater than 0 395 inches Table B describes the minimum recommended cable sizes needed for use with the heater and blower combinations in the EH1512 enclosure A WARNING When using a single power source for both camera and accessories consider the camera power consumption when determining the wire gauge Table B does not inc
7. EH1512 with a 24 VAC heater blower with 24 VAC camera power 12 W enclosure power consumption EH1512 3 Same as EH1512 with a 230 VAC heater blower with 24 VAC camera power includes the 4 inch wire tie 12 W enclosure power consumption 25 W maximum power consumption capacity EH1512 1MT Same as EH1512 with a 120 VAC heater blower with 24 VAC camera power and an EM1512 feedthrough wall mount includes the 4 inch wire tie 12 W enclosure power consumption 25 W maximum power consumption capacity EH1512 2MT Same as EH1512 with a 24 VAC heater blower with 24 VAC camera power and an EM1512 feedthrough wall mount 12 W enclosure power consumption EH1512 3MT Same as EH1512 with a 230 VAC heater blower with 24 VAC camera power and an EM1512 feedthrough wall mount includes the 4 inch wire tie 12 W enclosure power consumption 25 W maximum power consumption capacity 1512 1 15 Same as 1512 with a 120 VAC heater blower with 24 VAC camera power 1512 feedthrough wall mount includes the 4 inch wire tie and an 581512 sun shroud 12 W enclosure power consumption 25 W maximum power consumption capacity FH1512 2MTS Same as EH1512 with a 24 VAC heater blower with 24 VAC camera power an EM1512 feedthrough wall mount and an 551512 sun shroud 12 W enclosure power consumption EH1512 3MTS Same as EH1512 with a 230 VAC heater blower with 24 VAC camera power an EM1512 feedthrough wall mount includes the 4 inch wire tie and an 58
8. Fiber optic products TW3000 Series unshielded twisted pair UTP transmission products CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and C3651H 2X camera models ee years Pelco branded fixed camera models CCC1390H Series C10DN Series C10CH Series IP3701H Series and IX Series EH1500 Series enclosures Spectra IV products including Spectra IV IP Camclosure Series IS ICS IP integrated camera systems DX Series digital video recorders DVR5100 Series digital video recorders Digital Sentry Series hardware products DVX Series digital video recorders and NVR300 Series network video recorders Endura Series distributed network based video products Genex Series products multiplexers server and keyboard PMCL200 300 400 Series LCD monitors Two years Standard varifocal fixed focal and motorized zoom lenses DF5 DF8 Series fixed dome products Legacy Series integrated positioning systems Spectra 1 Spectra Mini Spectra Mini IP Esprit ExSite and PS20 scanners including when used in continuous motion applications Esprit Ti and TI2500 Series thermal imaging products Esprit and WW5700 Series window wiper excluding wiper blades CM6700 CM6800 CM9700 Series matrix Digital Light Processing DLP9 displays except lamp and color wheel The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty Intelli M elDC controllers One year Video cass
9. RY Manual Date Comments C3453 12 08 Original version C3453M A 3 09 C3453M B 4 09 Added security kit EH SKIT to the list of optional accessories 3453 5 09 Pelco the Pelco logo Camclosure Digital Sentry Endura Esprit ExSite Genex Intelli M Legacy and Spectra are registered trademarks of Pelco Inc Sarix and Spectra IIl are trademarks of Pelco Inc DLP is a registered trademark of Texas Instruments Incorporated Updated the manual to describe the change in the lanyard position and the revised maximum power consumption and heater blower kit power specifications A Phillips screwdriver is now required a flat head screwdriver is required for certain models A screw was added to the end of the enclosure Revised figures 1 and 2 the enclosure specification drawing the model table in the specification section and added Sarix cameras to the recommended camera list Added instructions for installing the security kit removed the Models table and moved optional accessories from the Specification section to the Description section All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights Copyright 2009 Pelco Inc All rights reserved PELLE by Schneider Electric www pelco com Pelco Inc Worldwide Headquart
10. ameter Light duty ceiling J mount maximum load 20 Ib 9 07 kg 360 pan rotation 75 tilt angle Check the environmental specification of your specific camera lens C3453M C 5 09 RECOMMENDED CAMERAS AND LENSES Cameras C10CH 6 C10CH 6X C10CH 7X C10DN 6 C1ODN 6X C10DN 7X CCC1390H 6 CCC1390H 6X IP3701H 2 IP3701H 2X IXSOC IXSODN IX10C IX10DN IXE20C IXE20DN IX30C IX30DN Lenses 13VD2 8 12 13VD3 8 13VD5 40 13VD5 50 13VDIR2 8 11 13VDIR3 8 5 13VDIR7 5 50 NOTE These lenses are for use with all cameras except Pelco IP cameras with Sarix technology Refer to the specific camera specification sheet for information on recommended lenses Design and product specifications subject to change without notice 3 80 5 9 65 16 01 40 67 3 27 8 31 891 2 64 6 71 lt a 14 00 35 56 SS1512 Sun Shroud l 14 39 36 55 gt 13 38 33 99 EH1512 Camera Enclosure 4 02 10 21 5 74 14 58 EM1512 Wall Mount NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES C3453M C 5 09 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years
11. ers 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120
12. ette recorders VCRs except video heads Video heads will be covered for a period of six months Six months All pan and tilts scanners or preset lenses used in continuous motion applications preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Auth
13. ic shock do not expose this apparatus to rain or moisture Installation should be done only by qualified personnel and conform to all local codes Unless this unit is specifically marked as NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Only use installation methods and materials capable of supporting four times the maximum specified load Only use replacement parts recommended by Pelco Do not use attachments such as mounts that are not recommended by Pelco They may be hazardous A CCC approved power cord must be used to power this equipment when used in China The product and or manual may bear the following marks A AN C3453M C 5 09 This symbol indicates that dangerous voltage constituting a risk of electric shock is CAUTION present within this unit RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit Description The EH1512 Series indoor outdoor enclosures are designed for use with small to medium sized analog and IP cameras They will accommodate both fixed and variable focal length lenses with or without auto iris operation They can be wall mounted using either Pelco s EM1512 feedthrough wall mount or any light to medium duty mount The tethered removable enclosure lid provides easy access during
14. ith the kit to loosen the three tamper resistant screws that are located on the enclosure base 2 Lift up and remove the lid refer to Figure 2 Hang the lid from the front of the enclosure base by the lanyards NOTE The gasket can come loose when the lid is removed Be sure to properly reseat the gasket when closing the lid if necessary Figure 2 Removing the Lid C3453M C 5 09 3 Remove the camera sled from the enclosure rail refer to Figure 3 a Squeeze the two plastic tabs located near the front window that hold the camera sled in place b Pull up and slide the sled forward c Remove the sled Figure 3 Removing the Sled 4 Remove the parts bag This includes the screws split washers glands and nuts 5 Remove the glands and nuts from the parts bag 6 Wire the enclosure e Without conduit for example the EM1512 mount Install and tighten the glands and nuts in the bottom of the enclosure Refer to Table A on page 11 for allowable cable diameter for the glands NOTE The PG11 gland might not accommodate RX11 coaxial cable because the coaxial diameter might be larger than the gland 0 395 inches 0 10 cm Glands can be mounted either inside or outside of the enclosure When using the EM1512 feedthrough mount Pelco recommends mounting the glands inside the enclosure with the nuts on the outside e With conduit Use a step drill to drill the larger hole to 0 875 inches 2 22 cm for 1 2 inch co
15. led Accepts camera and lens combinations including BNC connector up to 9 00 L x 2 87 W x 3 00 H 22 86 x 7 28 x 7 62 cm 0 118 inch 3 mm thick scratch resistant Lexan 2 81 W x 2 47 H 7 14 x 6 27 cm 1 x PG9 and 1 x PG11 compression glands on bottom PG9 0 312 inch 0 8 cm and PG11 0 395 1 0 cm maximum cable diameters 1x0 750 inch 1 91 cm diameter and 1 x 0 630 inch 1 6 cm diameter 0 750 inch hole will accept 1 2 inch NPT conduit fitting when enlarged to 0 875 inch 0 630 inch hole will accept 1 4 inch NPT conduit fitting 3 Allen head screws Die cast aluminum Alodine with gray polyester powder coat Indoor outdoor ambient temperature 10 to 120 F 23 to 49 C 13 38 inches 33 99 cm 14 39 inches 36 55 cm 2 50 Ib 1 13 kg 3 13 Ib 1 42 kg 3 25 Ib 1 47 kg 2 56 Ib 1 16 kg 3 25 Ib 1 47 kg 3 88 Ib 1 76 kg 3 19 Ib 1 45 kg 3 88 Ib 1 76 kg 4 76 Ib 2 16 kg 4 07 Ib 1 85 kg 4 76 Ib 2 16 kg Wall mount with feedthrough for EH1512 tilt angle of 20 to 70 sustains wind velocity up to 90 mph Light duty wall mount maximum load 20 Ib 9 07 kg Medium duty wall mount maximum load 40 Ib 18 14 kg with feedthrough tilt angle of 90 Medium duty wall mount maximum load 40 Ib 18 14 kg Medium duty pedestal mount maximum load 40 Ib 18 14 kg Medium duty mounts for pipe pole applications maximum load 40 Ib 18 14 kg fits poles with 3 inch 7 62 cm to 8 inch 20 32 cm di
16. lude camera power Table B Enclosure Accessory Wiring Distances Maximum Power Model Number Input Voltage Consumption Cable Size Cable Distance 20 AWG 2 782 ft 848 m 8 AWG 4 424 ft 1 348 m EH1512 1 120 VAC 22W 16 AWG 7 035 ft 2 144 m 4 AWG 11 184 ft 3 409 m 20 AWG 142 ft 43 m 8 AWG 225 ft 69 m EH1512 2 24 VAC 22W 16 AWG 358 ft 109 m 4 AWG 569 ft 173 m 20 AWG 6 473 ft 1 973 m 8 AWG 10 291 ft 2 137 m EH1512 3 230 VAC 22W 16 AWG 16 365 ft 4 988 m 4 AWG 26 019 ft 7 931 m 20 AWG 2 782 ft 848 m EH1512 1MT 8 AWG 4 424 ft 1 348 m EH1512 1MTS ee ou 16 AWG 7 035 ft 2 144 m 4 AWG 11 184 ft 3 409 m 20 AWG 142 ft 43 m EH1512 2MT 8 AWG 225 ft 69 m EH1512 2MTS EM ZW 16 AWG 358 ft 109 m 4 AWG 569 ft 173 m 20 AWG 6 473 ft 1 973 m EH1512 3MT 8 AWG 10 291 ft 2 137 m EH1512 3MTS ay 16 AWG 16 365 ft 4 988 m 4 AWG 26 019 ft 7 931 m C3453M C 5 09 Table C 24 VAC Wiring Distances Wire Gauge Total VA 20 AWG 0 5 mm 18 AWG 1 0 mm 16 AWG 1 5 mm 14 AWG 2 5 mm 10 283 ft 86 m 451 ft 137 m 716 ft 218 m 1142 ft 348 m 20 141 ft 42 m 225 ft 68 m 358 ft 109 m 571 ft 174 m 30 94 ft 28 m 150 ft 45 m 238 ft 54 m 380 ft 115 m 40 70 ft 21 m 112 ft 34 m 179 ft 54 m 285 ft 86 m 50 56 ft 17 m 90 ft 27 m 143 ft 43 m 228 ft 69 m Table C describes the recommended maximum dis
17. n the glands around the cables If the glands are mounted inside the enclosure do not tighten the glands around the cables until after you perform step 9 EM 1512 mount only Attach the enclosure using the threaded mounting holes in the bottom of the enclosure Use the M6 bolts and 6 mm split washer supplied in the parts bag Tighten the bolts to attach the enclosure body to the mount surface Tighten the glands around the cables EM 1512 mount only Adjust the enclosure position by loosening the M6 bolt at the bottom of the mount Position the mount as desired and then tighten the M6 bolt For mounts other than EM 1512 Perform the following steps a Install the mount according to the specific installation instructions supplied with the mount b Pull the video and power cables through the glands or conduit on the bottom of the enclosure Refer to Table B on page 11 to determine the size of power wire needed Refer to Table D on page 12 to determine the type of video coaxial cable needed NOTE Be sure to route all coaxial cable and wiring along the sides of the enclosure to avoid heating problems Maintain separation between 120 230 VAC 24 VAC and video wiring 12 13 14 15 16 C3453M C 5 09 Adjust the glands for a tight fit around the cables If you are wiring the enclosure with conduit install the fittings to connect the conduit to the enclosure Attach the camera to the sled with the 1 4 20 x 3 8 inch Phillips
18. nduit 7 Steps 8 9 and 10 contain instructions for installing the EM1512 mount If you are using a mount other than the EM1512 refer to the specific mount manual for installation instructions and then go to step 11 C3453M C 5 09 10 11 EM 1512 mount only Attach the mount to the wall a Use the mount as a template to mark and drill holes in the mounting surface b Pull the video and power cables from the wall through the mount If wiring with conduit use a step drill to drill a 0 875 inches 2 22 cm hole in one of the three knockout locations for 1 2 inch conduit Knockouts are indicated on the side and bottom of the mount arm Refer to Table B on page 11 to determine the size of the power wire needed Refer to Table D on page 12 to determine the type of video coaxial cable needed c Fasten the mount to the wall using a minimum of two flat washers not supplied and two 1 4 20 bolts not supplied AN WARNINGS f you install the mount outdoors rainwater could leak through the mounting bolt holes and damage the wall To prevent water damage seal the bolt holes with an appropriate sealant Apply the sealant around the bolt holes between the mount and the mounting surface e Use fasteners of a suitable size and make sure the mounting surface can support the combined weight of the mount and camera enclosure d Pull the cables through the glands in the enclosure If the glands are mounted outside the enclosure tighte
19. orization number RA and provide the following information Model and serial number 2 Date of shipment P O number sales order number or Pelco invoice number 3 Details of the defect or problem f there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS To expedite parts returned for repair or credit please call Pelco at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair and designated return location All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid 12 23 08 Green materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment REVISION HISTO
20. screw supplied and the 1 4 inch split lock washerwasher Refer to Figure 4 Align the front of the lens with the front edge of the sled Tighten the screw and then reinsert the sled Figure 4 Attaching the Camera to the Sled Refer to Figure 5 on page 10 to connect power to the enclosure and the camera Attach the video cables to the camera If required connect the ground wire to the ground screw boss and screw on the bottom of the enclosure which is located in front of the PC board For EH1512 1 and EH1512 3 pass the supplied zip tie through the hole in the PCB cover to secure the input power wires to the PCB COVer 17 Adjust the camera focal length and focus if necessary 18 Position the enclosure lid and close it If using the 10 24 x 0 75 inch hex head screws tighten them using a 5 mm Allen wrench not supplied If using the optional security kit insert the three tamper resistant screws supplied and tighten them using the 1 8 inch hollow screwdriver bit supplied When tightening either kind of screw ensure that the gasket is properly seated 120 VAC MODEL WIRING 24 VAC CAMERA OUTPUT 24 VAC CAMERA OUTPUT HIGH LOW ACIN AC OUT NT HI NT INPUT AC HIGH INPUT AC LOW NEUTRAL ZIP TIE HERE 0 GROUND BOSS 120 VAC CAMERA OUTPUT LOW NEUTRAL 120 VAC OUTPUT HIGH 24 VAC MODEL WIRING INPUT A
21. tances for 24 VAC applications which are calculated with a 10 percent voltage drop Ten percent is generally the maximum allowable voltage drop for AC powered devices For example an enclosure that requires 30 VA and is installed 94 feet 28 m from the transformer would require a minimum wire gauge of 20 AWG Table D Video Coaxial Cable Wiring Distance Cable Type Maximum Distance RG59 U 750 ft 229 m RG6 U 1 000 ft 305 m RG11 U 1 500 ft 457 m Minimum Cable Requirements 75 ohm impedance All copper center conductor All copper braided shield with 9596 braid coverage Maintenance Clean the window regularly to maintain picture clarity Use a soft cloth and a mild nonabrasive detergent and water C3453M C 5 09 Specifications MECHANICAL Camera Mounting Camera and Lens Size Viewing Window Viewing Area Cable Entry Cable Entry Holes Lid Fastening GENERAL Construction Finish Environment Unit Length Base Overall Unit Weigh EH1512 12MT 21 12 2 12 3 12 1MT 12 2MT 12 3MT 2 1MTS 12 2MTS 12 3MTS I OI OI OI FT FT FT TFT TT RECOMMENDED MOUNTS Wall 1512 EM1450 EM2400 EM1900U EM22 Pedestal EM1009U EM1015U MM22 Pipe Pole EM1109 EM2000 EM2200 Ceiling EM3000 Assumes the lens is fully extended Single slot for adjustable camera positioning on snap in camera s
Download Pdf Manuals
Related Search