Pelco Security Camera 90 User's Manual
Contents
1. Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number sales order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding2. 4 Attach the surface trim ring and back box to the adapter plate with the two 8 32 x 2 50 inch screws supplied 4S STANDARD ELECTRICAL BOX CEILING WALL 8 32 X 1 004 SUPPLIED H OPTIONAL i ADAPTER RING 8 32 X 2 50 BACK BOX AND SUPPLIED SURFACE MOUNT Figure 7 4S Standard Electrical Box Installation C2462M D 3 08 13 INSTALLATION IN A 4S DEEP ELECTRICAL BOX Refer to Figure 8 and complete the following steps 1 Remove the surface mount ring from the back box Refer to Figure 5 and complete the following steps a Place your fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box 2 Attach the adapter ring to the 4S box with the two 8 32 x 1 00 inch screws supplied 3 Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted pair Connect the blue wire to Video connect the gray wire to Video 4 Connect the power wires Table E Power Input 4S Deep Electrical Box Installation Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC operation only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and then connect the other side of the transformer to the black wire on all units Failure to connect al
3. and then connect the other end to any standard BNC VIDEO IN connector on a monitor To assemble a longer service cable for the ICS090 Series Camclosure purchase the following parts at a local electronics supply store Oty Description 1 25mm monaural headphone plug 1 CPM 88 miniature coaxial connector 1 RG174 U coaxial cable To assemble the cable 1 Attach the CPM 88 miniature coaxial connector to one end of the cable Follow the directions supplied with the miniature coaxial connector 2 Referto Figure 13 and complete the following steps to attach the 2 5 mm monaural plug to the other end of the coaxial cable a Remove the support sleeve from the plug and then slip the support sleeve over the end of the cable b Prepare the cable c Solder the center connector of the cable to the center pin of the plug d Thread the braid of the cable through the hole in the crimp pin and then solder the braid to the top of the crimp pin e Crimpthe end of the crimp pin around the cable f Reassemble the support sleeve and the plug CENTER CONDUCTOR CABLE BRAID SHIELD 2 5 mm MONAURAL HEADPHONE PLUG Figure 13 Connecting the Monaural Headphone Plug to the Coaxial Cable 20 C2462M D 3 08 Specifications BACKBOX Electrical Input Voltage Power Consumption Video Connector General Pan Tilt Adjustment Pan Tilt Rotation Construction Back Box and Surface Mount Ring Bubble Finish Environment Operating T
4. compensation BLC switch ON ABL switch OFF on OFF mm ac NOTUSED E ELC OFF OFF C2462M D 3 08 VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLY When using more than one camera power supply a brief vertical roll may occur on the monitor when a camera view is switched To eliminate vertical roll reverse the 24 VAC connections on one camera If both cameras are connected to the same transformer this should solve the problem If reversing the connections does not solve the problem adjust the phase control by synchronizing or line locking the cameras to one another ADJUSTING THE PHASE CONTROL It may be necessary to have two people in communication when synchronizing the cameras one person at the camera and another person at the monitor to observe the vertical roll and the effect of any adjustments made at the camera To synchronize the cameras 1 Choose a reference camera to which all other cameras will be phased 2 Select a camera and synchronize it to the reference camera by turning the phase adjustment control refer to Figure 10 clockwise or counterclockwise 3 Each time an adjustment is made switch back and forth between the camera you are adjusting and the reference camera Repeat this process as many times as necessary until the roll between the cameras is no longer noticeable 4 Adjust the phase of all other cameras by repeating steps 2 and 3 Always adjust to the reference camera
5. selected in step 1 NOTE The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the vertical sync pulses of the reference camera to the selected camera s PHASE ADJUSTMENT SERVICE CONNECTOR Figure 10 Vertical Phase Adjustment C2462M D 3 08 17 Reinstall the Dome Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner reinstall the liner before installing the dome bubble To install the liner refer to Figure 11 complete the following steps Align the studs located on the camera module with the clips on the liner Lightly pinch the sides of the liner opposite from the clips and place the clips over the studs Once the liner is secure position the viewing window of the liner over the lens of the camera Install the bubble Boos cx Figure 11 Installing the Dome Liner 18 C2462M D 3 08 DOME BUBBLE INSTALLATION To install the dome bubble refer to Figure 12 and complete the following steps 1 Select the bubble clear or smoked 2 Align the standoffs of the bubble with the slots of the back box 3 Turn the bubble clockwise until it locks in place Figure 12 Installing the Dome Bubble C2462M D 3 08 Service Connector An optional 4 foot service monitor cable part number ICS090 SC is available for on site setup and adjustments To use the cable simply plug one end of the cable directly into the service connector of the ICS090
6. 090 Series Camclosure integrated camera system Qty Description Assembled ICS090 Series Camclosure back box smoked dome bubble and camera module Clear dome bubble Plastic liner Adapter plate 8 32 x 1 00 inch Phillips pan head screws 8 32 x 2 50 inch self tapping screws 1 1 1 1 2 2 8 32 x 0 750 inch self tapping screws 2 2 10 32 x 1 50 inch self tapping screws 6 C2462M D 3 08 Remove the Dome Bubble Turn the dome bubble counterclockwise and lift refer to Figure 1 Place the bubble on a nonabrasive surface If the unit is supplied with a dome liner remove the liner before installing the unit To remove the liner gently lift it from the unit Place the liner to the side it will be reinstalled along with the bubble after the installation has been completed following installation Figure 1 How to Remove the Dome Bubble C2462M D 3 08 7 Install the Back Box The installation methods for the ICS090 Series include the following options Mount to the surface of a ceiling or wall Install in a suspended ceiling Install in a fixed ceiling or wall Mount to the surface of a 4S standard electrical box Install in a 4S deep electrical box Select the best method for your installation and refer to the following pages for instructions INSTALLATION TO SURFACE OF A CEILING WALL Refer to Figure 2 for the following steps Refer to Figure 3 if installing the unit to a concrete ceiling wall 1 2 P
7. Ceiling Wall Installation C2462M D 3 08 9 IN CEILING INSTALLATION SUSPENDED CEILING Refer to Figure 4 and complete the following steps 1 Remove the ceiling tile from the ceiling 2 Cut a 4 inch diameter hole in the ceiling tile 3 Remove the surface mount ring from the back box Refer to Figure 5 and complete the following steps a Place your fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box NOTE Do not discard the surface mount ring because it is required to complete the installation 4 Turn the surface mount ring upside down and place it on the inside of the ceiling tile 5 Attach the back box to the ceiling tile and surface mount ring with two 10 32 x 1 50 inch self tapping screws supplied SURFACE MOUNT RING 10 32 x 1 50 SELF TAPPING SCREWS SUPPLIED Figure 4 Ceiling Tile Installation 6 Replace the ceiling tile 7 Remove an adjacent ceiling tile and connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted pair Connect the blue wire to Video connect the gray wire to Video 8 Connect the power wires Table B Power Input Suspended Ceiling Installation Voltage Red Wire Black Wire 12 VDC Ground 24 VAC 10 C2462M D 3 08 STANDOFF SURFACE MOUNT RING Figur
8. INSTALLATION 090 Series Camclosure Indoor Integrated Camera System Surface Mount In Ceiling C2462M D 3 08 Contents Important Safety Instructions oesters bloe Mia oo la Bed adefo LEMA dd Rm LE d 5 Regulatory Notices esae ua ui ER EL QU EURO EER Weer eau DERE Puede Pan 5 D amp scrption wan Aenean eut tt ya he nd ra eub Or e HL hoe Sued ale d e Ad 6 Parts biston oct ere EEEN oaeen TA ee ER 6 Remove the Dome Bubble eee eeen 7 Install th Back BOX es sao ye Sian eee e m re Ost dd xx e eR Was atd Beedle 8 Installation to Surface of a Ceiling Wall eeen 8 In Ceiling Installation Suspended Ceiling nennen 0 In Ceiling Installation Fixed Ceiling Wall nnen 2 Installation to The Surface of a 4S Standard Electrical Box ananena 3 Installation in a 4S Deep Electrical Box eeen 4 Gamera Positloning oot teen lean ENOR Ca endorse ade 5 Camera Adjustments aaan overde edentate ae edentate 16 SWIECHISEL NGDS vaer ean Sagas Vane Cr EE WEEKE 6 Switch Settings for Fixed Focal Length Lens Without Auto Iris 000 6 Vertical Phase Adjustment 24 VAC Operation Only 00 00 c cece cence ee eee 7 Adjusting the Phase Control eee 7 Reinstall the Dome Bubble 5 zeten kaa erna tere uhren E Ep RR WENT eg ee 8 Dome Liner Installation 4 i oes pr RR Mas weeer bende Ub the ex en nae 8 Dome Bubble Installation onee eee 9 Setyice Connector 2 s
9. e 5 How to Remove Surface Mount Ring from Back Box AC operation only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and then connect the other side of the transformer to the black wire on all units Failure to connect all of the units in the same way will cause the cameras to be out of phase with each other which might produce a vertical roll when switching between cameras C2462M D 3 08 11 IN CEILING INSTALLATION FIXED CEILING WALL Refer to Figure 6 and complete the following steps il 2 Cut a 4 inch diameter hole in the ceiling wall Remove the surface mount ring from the back box Refer to Figure 5 and complete the following steps a Place your fingers on the circular marks located on the sides of the surface mount ring b Pinch the sides c Lift and remove the surface mount ring from the back box Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted pair Connect the blue wire to Video connect the gray wire to Video Connect the power wires Table C Power Input Fixed Ceiling Wall Installation Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and then connect
10. emperature Weight Unit Shipping 12 VDC or 24 VAC 10 autosensing 3 W or less BNC 360 140 20 to 160 range 360 ABS plastic Polycarbonate White Indoor 32 to 120 F 0 to 49 C 0 52 Ib 0 24 kg 2 0 Ib 0 91 kg Design and product specifications subject to change without notice 5 30 13 46 KE T 4 TI 1 65 4 19 y ai 4 04 10 26 10 26 2 39 6 07 3 90 i 9 91 8 31 Y v San Y NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES C2462M D 3 08 21 Green The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment E 22 C2462M D 3 08 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on fiber optic products and TW3000 Series unshielded twisted pair UTP transmission products Three years on Spectra IV products Three years
11. ia asec band yb dae ed ded one oa an eiaa ii 20 SPOCIIGATIONS x s repo re tere na d sos det Bagge Dhaene Ant 21 Backbox Er coe erc ote as EE ae foe Gea aer dt erg 21 C2462M D 3 08 3 List of Illustrations oe U N gt N C co How to Remove the Dome Bubble isissssssssssssssssssm IR 7 Ceiling WallInst llation 2 4 iet toe ioserkier eve e Ren AO ERE er hed 9 Concrete Ceiling Wall Installation lisse 9 Ceiling Tle Installation pii 125 nerit e idee Se ee Mead ad Ae eae ean eee Bld 0 How to Remove Surface Mount Ring from Back Box 00 0 ccc eee eee eee eee 11 In Ceiling Installation to a Fixed Ceiling Wall ee 2 AS Standard Electrical Box Installation 0 nnee 3 4S Deep Electrical Box Installation neen 4 Positioning the Camera eeen 5 Vertical Phase Adjustment eneen nee en eneen e 7 Installing the DOMe LING Fx arne zeshonderd ende den ARI 8 Installing the Dome Bubble nennen eeen eenen 9 Connecting the Monaural Headphone Plug to the Coaxial Cable n on nnnanaaana aeaa 20 List of Tables A m QC c W Power Input Surface of Ceiling Wall Installation ne 6 Power Input Suspended Ceiling Installation 0 0 2 2 0000 00 cece cece cece eee eee 8 Power Input Fixed Ceiling Wall Installation lisse 10 Power Input 4S Standard Electrical Box Installation ccc cece cece eee eee 11 Power Input 4S Deep Electrical Box Installa
12. ich can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You may also find helpful the following booklet prepared by the FCC How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission s rules This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada C2462M D 3 08 5 Description The ICS090 Series Camclosure integrated camera system integrates a camera and lens package in a small discreet dome The system is easy to install and can be mounted or recessed to the surface of a ceiling or wall Prior to the installation of your new system thoroughly familiarize yourself with the information in this manual PARTS LIST The following materials are supplied with the
13. is a registered trademark of Texas Instruments Incorporated PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1809001 Australia Finland France Germany Italy Macau The Netherlands Russia Singapore South Africa Spain Sweden United Arab Emirates United Kingdom United States
14. l of the units in the same way will cause the cameras to be out of phase with each other which might produce a vertical roll when switching between cameras 5 Attach the back box to the adapter plate with the two 8 32 x 0 750 inch screws supplied 4S DEEP ELECTRICAL BOX CEILING SUPPLIED 8 32 X 750 BACK SUPPLIED BOX Figure 8 4S Deep Electrical Box Installation 14 C2462M D 3 08 Camera Positioning Manually rotate and tilt the camera module to position the camera Do not over rotate the module AN WARNING Excessively turning the module in one direction could result in damage to the wiring Tilt 140 Pan 360 Rotation 360 Figure 9 Positioning the Camera C2462M D 3 08 15 Camera Adjustments SWITCH SETTINGS SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots e _ ALC ELC switch Always ELC e _ Y DC switch Not used e Auto backlight compensation BLC switch OFF ABL switch ON FACTORY SETTINGS E 2 tn ea a i E SWITCH POSITION Y e Manual backlight
15. on Genex Series products multiplexers server and keyboard e Three years on DX Series digital video recorders DVR5100 Series digital video recorders DigitalSENTRY Series hardware products DVX Series igital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products Three years on Camclosure and Pelco branded fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Three years on PMCL200 300 400 Series LCD monitors Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra III Spectra Mini Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Two years except lamp and color wheel on Digital Light Processing DLP9 displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty e Two years on Intelli M elDC controllers e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications preset scan tour and auto scan modes
16. the other side of the transformer to the black wire on all units Failure to connect all of the units in the same way will cause the cameras to be out of phase with each other which might produce a vertical roll when switching between cameras Use the 3 16 toggle bolts not supplied to attach the back box to the mounting surface 3 16 TOGGLE BOLTS NOT SUPPLIED Figure 6 In Ceiling Installation to a Fixed Ceiling Wall C2462M D 3 08 INSTALLATION TO THE SURFACE OF A 4S STANDARD ELECTRICAL BOX Refer to Figure 7 and complete the following steps 1 Attach the adapter ring to the 4S box with the two 8 32 x 1 00 inch screws supplied 2 Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted pair Connect the blue wire to Video connect the gray wire to Video 3 Connect the power wires Table D Power Input 4S Standard Electrical Box Installation Voltage Red Wire Black Wire 12 VDC Ground 24 VAC AC Operation Only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to the red wire on all units and then connect the other side of the transformer to the black wire on all units Failure to connect all of the units in the same way will cause the cameras to be out of phase with each other which might produce a vertical roll when switching between cameras
17. the warranty of a product that does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS To expedite parts returned for repair or credit please call Pelco at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair and designated return location All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid 1 8 08 REVISION HISTORY Manual Date Comments C2462 11 02 Original version C2462M A 1 03 Added Regulatory Notices for FCC Class B C2462M B 10 05 Revised switch setting descriptions for varifocal lens Added WEEE statement C2462M C 1 06 Updated factory switch settings for varifocal lens per ECO 13164 Updated wiring information Added information about dome bubble C2462M D 3 08 Revised for standard resolution color cameras with fixed focal lenses Pelco the Pelco logo Camclosure DigitalSENTRY Endura Esprit ExSite Genex Intelli M Legacy and Spectra are registered trademarks of Pelco Inc Spectra Ill is a trademark of Pelco Inc Copyright 2008 Pelco Inc All rights reserved DLP
18. tion ccc ccc eee eee 12 C2462M D 3 08 Important Safety Instructions 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Use only installation methods and materials capable of supporting four times the maximum specified load Regulatory Notices This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference eceived including interference that may cause undesired operation RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference 0 radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception wh
19. ull video and power wires through the ceiling wall Connect the video cable wires BNC Connect the BNC connector from the Camclosure to a mating BNC connector Twisted pair Connect the blue wire to Video connect the gray wire to Video Connect the power wires Table A Power Input Surface of Cei ing Wall Installation Voltage Red Wire Black Wire 12 VDC Ground 24 VAC jn AC operation only If you are wiring more than one ICS090 Camclosure to the same transformer connect one side of the transformer to transformer to the black wire on all un the red wire on all units and then connect the other side of the its Failure to connect all of the units in the same way will cause the cameras to be out of phase with each other which might produce a vertical roll when switching between cameras C2462M D 3 08 4 Use the 6 32 toggle bolts not supplied to attach the surface mount ring and back box to the mounting surface refer to Figure 2 NOTE For a concrete ceiling wall installation use 8 32 mounting hardware not supplied refer to Figure 3 WALLOR CEILING HII HH HH LH LLL 6 32 TOGGLE BOLTS NOT SUPPLIED ox BOX AND SURFACE MOUNT RING Figure 2 Ceiling Wall Installation CONCRETE WALL OR CEILING LLL EL E LE BLUE LLL 8 32 MOUNTING HARDWARE NOT SUPPLIED gt i BACK BOX i AND SURFACE MOUNT RING Figure 3 Concrete
Download Pdf Manuals
Related Search