Pelco ICS-DO101ABK User's Manual
Contents
1. VIDEO CONNECTOR HEATER CONNECTOR 1093 6 Pelco Manual C2436M B 9 02 CAUTION A Heater elements could be hot When camera power is on use caution when adjusting the camera This applies to all models Install Camera 1 Some indoor installations do not require a heater If the installation does not require a heater remove the heater board from the cam era assembly To remove the heater apply pressure and press on the corner of the board 2 If the heater is installed plug the heater con nector from the camera into the mating con nector inside the base Plug the video con from the camera into the mating connector inside the base Turn on power to the camera and monitor CONNECTOR 3 If you have a varifocal lens hold assem bly in your hand and point the lens toward what you want to view Loosen the focal length and focus locking screws Adjust ac cording to scene detail Retighten the screws LOCKING SCREWS 4 Always make sure the tab on the camera bracket is pointing out of the enclosure away from the mount Gently squeeze the bracket TOROF place it against the shoulder inside the base CAMERA and gently release Proper camera orientation The camera CAMERA BRACKET bracket tab points out of the enclosure and TAB ALWAYS POINTS OUT OF THE the top of the camera is pointed in the oppo ENCLOSURE os site direction Pelco Manual C2436M B 92. 02 7 G Install Dome and Trim Ring 1 Align the screw holes in the trim ring with those in the camclosure base LOOSEN SCREWS 2 Domes with Liners only Position the viewing window over the lens of the camera a Loosen the three Phillip screws located in the dome b Insert the blade of a standard screwdriver in one of the adjustment grooves Move dome into position Tighten the three Phillip screws to lock liner in place 3 Tighten the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit ADJUSTMENTS COLOR CAMERA ONLY If you have a color camera it is set up at the factory and normally requires no adjustments Sometimes however adjustments may be necessary 1 Remove the dome and trim ring using the supplied 1 8 inch hollow screwdriver bit 2 Adjustthe vertical phase iris level focus or switch settings refer to procedures below VARIFOGALEENS 3 Replace the dome and trim ring mE VERTICAL PHASE ADJUSTMENT Vertical Phase 24 VAC Operation Only Adjustment is required if there is vertical roll when switching between two cameras 1 Reverse the 24 VAC connections on one camera If both cameras are connected to the same transformer this should solve the problem FIXED LENS 2 If reversing the connections does not solve the problem or if cameras are connected to different transformers turn the adjust ment screw on one camera while switching as rapidly as possible
3. between the two camera views until the switching is clean and there is no vertical roll If more than two cameras are out of syn VERTICAL PHASE ADJUSTMENT Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris you can adjust the level setting to increase or decrease brightness VARIFOCAL LENS a AUTO IRIS LEVEL E ADJUSTMENT 8 Pelco Manual C2436M B 9 02 Focus Adjustment for Fixed Focal Length Lens with Auto lris CAUTION Heater elements could be hot When camera power is on use caution when adjusting the camera To adjust the focus it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens To remove the heater board 1 Disconnect the four pin heater wiring 2 Waitfor the heater elements to cool if they are hot 3 Apply pressure and press on the corner of the board To adjust the focus Loosen the locking screw on the bottom of the lens Move the screw in the slot to bring the picture into focus Retighten the locking screw Replace the heater board if it was removed Reconnect the four pin heater wiring Cn E co ho cx BOTTOM VIEW OF CAMERA WITH HEATER BOARD REMOVED Switch Settings for Fixed Focal Length Lens with Auto lris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used under varying lighting co
4. made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s iability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which
5. Added instructions for fixed lens with auto iris C2436M B 9 02 Revised installation instructions bracket and camera assembled at factory Added iris level adjustment for fixed lens with auto iris 12 Pelco Manual 2436 9 02
6. PELLO Installation Operation ICS DO101ABK Integrated Camera System for the MR5000 Series Public View System C2436M B 9 02 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 2 Pelco Manual C2436M B 9 02 TABLE OF IMPORTANT SAFEGUARDS AND WARNINGS 5 DESCRIPTION ag ara hard dase pies 5 INSTALLATION si oe ul whee nal 5 ADJUSTMENTS COEOR CAMERA ONLY pen ro e hd ert p RH per EN E Rex Reg 8 VERTICAL PHASE 24 VAC OPERATION ONLY 8 AUTO IRIS LEVEL ADJUSTMENT ttt e reete hr Rhe Exe Rees 8 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO 9 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO RIS 9 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS 10 SWITCH SETTINGS FOR VARIFOCALLENS 10 SPECIFICATIONS e EUER 11 REGULATORY oe pud eta pere prosa pe dais 11 WARRANTY AND RETURN INFORMATION n 12 Pelco Manual C2436M B 9 02 3 4 Pelco Manual C2436M B 9 02 IMPORTANT SAFEGUARDS AND WARNINGS 1 Installation and servicing should only be done by qualifi
7. d through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm 3 Pull power wires through the ICS DO101ABK feedthrough located at the bottom of the mount arm Remove the 50 inch plug if it is installed ADAPTER PLATE CAMCLOSURE BASE 4 Pul wires through the adapter plate of the NOTE POSITION THE BASE SO THAT THE CONDUIT COVER ICS DO101ABK and into the base of the IS TURNED TOWARDS THE BACK OF THE MOUNT ICS DO101ABK 5 Use the supplied 3 16 inch Allen wrench and slightly loosen do not remove the two 5 16 18 x 75 inch Allen pan head screws that secure the MR5000M mount base to the mount arm 6 Feedthe video cable attached to the ICS DO101ABK back box through the ICS DO101ABK feedthrough in the mount arm and out the bottom end of the mount arm 7 Hook the adapter plate over the loosened screws Tighten the screws to secure the adapter plate to the mount Connect Video and Power 1 Connectthe video cable Place the cable inside the MR5000 Series mount arm and install the bottom end cap of the mount to conceal the cable 2 Depending on the input voltage connect either the 12 VDC or 24 VAC input power wires to the appropriate positions on the terminal block inside the base 3 12 VDC Operation Only The camera is set for 24 VAC operation at the factory For 12 VDC operation remove the jumper from the 24 VAC position and install it on the 12 VDC position POWER TERMINAL
8. ed service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 35 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Use only installation methods and materials capable of supporting four times the maximum specified load DESCRIPTION Designed specifically for the MR5000 Series Public View System the ICS DO101ABK Integrated Camera System packages a camera and lens into a small discreet high security dome Pelco s MR5000 Public Viewing Station is specifically designed for retail applications to provide a clear visual warning to potential shoplifters that these premises are under surveillance When properly installed the station is an effective deterrent against shoplifting INSTALLATION IMPORTANT To maximize tamper resistance when not using the side conduit opening for wire connections verify that the conduit plug and set screw are tight Q Attach Adapter Plate to Base of ICS DO101ABK 1 Align the adapter plate to the base of the ICS DO101ABK 2 Using the two 10 32 x 375 inch pan head screws and internal lock washers attach the base of the ICS DO101ABK to the adapter plate Pelco Manual C2436M B 9 02 5 Prepare Video and Electrical Cabling 1 Temporarily remove the bottom end cap of the MR5000 Series mount if it is installed 2 Feedthe 42 inch video cable provide
9. ertamance in liahtin 014 ESC Electronic shutter control M 515 Backlight compensation conditions where auto iris is c 346 FL Flickerless required It is also configured with 7 AE Automatic exposure the shutter speed set at 1 60 ul lt 8 Notused 1 50 PAL and AGC set at 6 dB of gain To enable automatic exposure Turn on switch 7 and then turn on off switch 4 for electronic shutter control switch 5 for backlight compensation and switch 6 for flickerless motion To manually set and lock AWB Place a white background in front of camera and turn off switch 1 For gamma correction Switch to accurately reproduce scene brightness when turned on y 7 0 6 and when turned off 1 0 For control Switch 3 On increases gain by 6 dB and switch 3 Off increases gain by 18 dB 10 Pelco Manual C2436M B 9 02 FACTORY SETTINGS Y o a a E a lt NOT USED Ec SN c DC OFF N OFF SWITCH POSITION FACTORY SETTINGS Qom 2345678 ERR NR UN 0000010 SWITCH POSITION To enable auto iris and manually set shutter speed Turn off switch 7 set switches 4 5 and 6 for the desired shutter speed CAUTION Do not change the shutter speed unless you understand how changing the settings will affect the scene detail Shutter Swi
10. nditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots ALC ELC switch Always ALC FACTORY SETTINGS 9 98 YIDC switch Always DC ASIE MER MS ON Auto backlight compensation switch OFF i I ABL switch ON Manual backlight compensation switch ON 2 8 66 ABL switch OFF SWITCH POSITION Pelco Manual C2436M B 9 02 9 Switch Settings for Fixed Focal Length Lens Without Auto lris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots ALC ELC switch Always ELC YIDC switch Not used ON Auto backlight compensation switch OFF bes ABL switch ON Manual backlight compensation BLC switch ON ABL switch OFF Switch Settings for Varifocal Lens The high resolution camera with 1 AWB Mone white balance ap 2 GAM Gamma function varifocal lens and auto iris is AGC Automatic gain control configured the factory for c ottima p
11. ons Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to cor rect the interference at his own expense FCC Class B color NTSC cameras only except varifocal This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interfer ence by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Pelco Manual C2436M B 9 0 11 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any me
12. rchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty e Two years on standard motorized or fixed focal length lenses e Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products e Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products e year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs
13. tch Number and Position Speed 7 6 5 4 1 60 NTSC 1 50 PAL on On On 1 100 Off On On 1 250 Off On Off On 1 500 Off Off On 1 1000 On On Off 1 2000 Off On Off 1 4000 On Off Off 1 10000 Off Off Off SPECIFICATIONS Electrical mE Input Voltage 12 VDC or 24 VAC 10 Ratings IP 66 when installed Power ag y Consumption 13 watts or less UL cUL Him BNC Construction Aluminum with steel camera Operatin mounting bracket and polycar ia ue 50 to 122 F 46 to 50 C en De ices to 10 F 23 C Vipegeoterp General Cable Entry 3 4 inch 1 91 conduit fitting 288 eee E inches and 3 4 inch 1 91 opening Bubble 3 75 inch diameter Pan Tilt TORNET threaded ps Environment Low temperature indoor outdoor Adjustment Manual 360 pan 180 tilt Unit Weight 2 20 lb 1 00 kg Design and product specifications subject to change without notice Regulatory Notices FCC Class A monochrome EIA cameras only This equipment has been tested and found to comply with the limits of a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the in Struction manual may cause harmful interference to radio communicati
14. the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2002 Pelco All rights reserved REVISION HISTORY Manual Date Comments C2436M 9 01 Original version C2436M A 7102
Download Pdf Manuals
Related Search