Pelco WLV500-1 User's Manual
Contents
1. voltage If the voltage out of the supply is less than 12 0 volts the power supply needs to be replaced Please contact PELCO for a replacement 3 If the system is still not operating after successfully verifying the steps above the fault must lie within the wireless control link system Please contact PELCO imme diately for a replacement It is our policy to provide quality products to our customers If the transmitter and receiver are now placed in their required locations and there is intermittent control fail ures on the pan and tilt there are several possible reasons that need to be addressed individually 1 Exceeding Maximum Range The base models of these units are specified to operate at 1 000 feet maximum line of sight distance Obstructions between the transmit ter and receiver antennas will reduce maxi mum range The maximum distance will vary depending on the type and number of obstruc tions encountered If the operating distance is nearing 1 000 feet then we recommend an upgrade to the receiver antenna Note Interference The WLV500 Series transmit in the 2 4 GHz band Although this band is less crowded than the 900 MHz band it is still susceptible to some outside interference including mobile video transmission Most interference should be very temporary but if consistent interfer ence occurs there are 3 channels that are avail able At no cost to the user the unit can be replaced by a system that2. 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 1994 Pelco All rights reserved PELCO PELCO 3500 Pelco Way Clovis CA 93612 5699 559 292 1981 e 800 289 9100 FAX 800 289 9150 or 559 292 3827 Product specifications subject to change without notice Cc901M Pelco Manual C901M 1 94
3. 7 V Impedance 75 ohms Connectors BNC Pelco Manual C901M 1 94 1 RF Case Finish Transmitter Cover Black paint Radiated Power FCC Part 15 15 249 Base Alodine aluminum Transmit Antenna Attached circular polarized patch Environmental Receive Connector TNC Operating Temperature 20 to 65 C Receive Input Impedance 50 ohms Storage Temperature 50 to 85 C Frequency Operating Range 2400 to 2483 MHz Humidity Non condensing 90 System Frequency Options Factory Set WLV500KT 1 2401 MHz 4 0 INSTALLATION WLYVS500KT 2 2428 MHz WLVSO0KT 3 2455 MHz 4 1 VIDEO AND POWER CONNECTIONS WLYVS500KT 4 2482 MHz The following instructions are for use with the Frequency Stability 0 005 PELCO Coaxitron System 2000 Modulation Wideband FM 1 Refer to Figure 1 The output port labeled f INPUT FROM RECEIVER of the Coaxitron Operating System 2000 transmitter should be connected Distance 1 000 feet maximum line of to the BNC connector indicated on the label as sight DATA IN VIDEO OUT of the WLV500TX Consult factory for extended control link transmitter The video signal that operating range originated from the WLV1000RX wireless video receiver or directly from a camera or other video source should be connected to the BNC connector labeled VIDEO IN of the Power Each Unit Input Voltage 12 to 16 VDC WLV500TX The port labeled OUTPUT TO MONITOR of the Coaxitron System 2000 Input Cur
4. INSTALLATION OPERATION MANUAL fF WLV500 SERIES WIRELESS VIDEO EL La TRANSMISSION SYSTEMS 1 0 SCOPE 2 2 MODELS The information contained within this manual covers WLV5S00 1 Channel 1 the installation and operation of the PELCO WLV500 WLYV500 2 Channel 2 Series wireless control link system WLV500 3 Channel 3 WLV500 4 Channel 4 Installation should be in accordance with FCC regula tions and all applicable local and national electric codes Transmitter WLV500TX utilizing approved materials only Receiver WLV500RX Power Supplies TRFDP15VDC 500M Please thoroughly familiarize yourself with the infor Mounting Hardware WLVHRDWRKIT mation in this manual prior to installation and operation 2 3 ANTENNA OPTIONS 2 0 DESCRIPTION WLVAN 2R Medium Gain CP Patch RH 6 dB PELCO s WLV500 Series wireless control link system WLVAN 2L Medium Gain CP Patch LH 6 dB is designed to provide wireless remote control of cam WLVAN 3R High Gain CP Panel RH 13 dB era positioning and zoom functions The system is WLVAN 3L High Gain CP Panel LH 13 dB compatible with coaxitron remote control systems such as a PELCO Coaxitron System 2000 and operates iin conjunction with the WLV 1000 wireless video sys 3 0 SYSTEM SPECIFICATIONS tem Data 2 1 WLV500 SYSTEM COMPONENTS a NRZ 1 WLV500TX Transmitter Pulse Width 1V p p 1 WLYVSOORX Receiver 2 15 volt AC DC converters Duty Cycle 50 1 Set mounting hardware kit Levels Video Compatible 0 0 to 0
5. c objects For large separations it is recommended that a two way voice communication device be used to best position the transmitter and receiver When a suitable location is found the mounting brackets should be used to secure the units in place VIDEO VIDEO OUT AUDIO MONITOR O OUTPUT TO MONITOR PELCO See sysTEM 2000 COAXITRON VIDEO INO WLV500T X TRANSMITTER Figure 1 Typical WLV1000 Video WLV500 Control Link System Configuration Pelco Manual C901M 1 94 4 3 TROUBLESHOOTING It is recommended that the wireless transmission con trol link system be first tested with both the WLV500 and WLV 1000 transmitters and receivers in close prox imity 3 to 6 feet to ensure proper interconnection of the coaxitron receiver and transmitter with the wireless transmitters and receivers If all interconnections are made appropriately as described there should be unin terrupted remote control of the pan and tilt device If there should be difficulties at this point then 1 Check the performance of the system minus the wireless control link transmitter and re ceiver by directly connecting the coaxitron transmitter to the coaxitron receiver This will verify the performance of the coaxitron sys tem as well as verify that the interconnecting cables are good 2 If the verification detailed in 1 above is performed and the system is fully reconnected and there is still not full control check the power supply
6. c use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state Ifa warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco Pelco Manual C901M 1 94 RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292
7. ies products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty e Two years on standard motorized or fixed focal length lenses e Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products e Two years on Spectra Esprit ExSite and PS20 scanners includ ing when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications thatis preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specifi
8. m the WLYV500RX receiver preventing reliable operation To prevent jamming and achieve reliable operation at maxi mum range the WLV500RX antenna must be located a minimum of 4 5 feet from the WLV1000TX antenna The distance between the WLV500TX and WLYV1000RX antennas is not critical since the narrow band emissions of the WLV500TX will not noticeably affect the received video signal from the WLV 1000RX but it is recommended to maintain at least 10 inch separation O VIDEO IN WLV1000T X CAMERA ATTITUDE PAN TILT CONTROL CABLE HARNESS O DATA OUT COAXITRON OUTH RECEIVER WLV500RX WLV1000RX DATA IN VIDEO OUT O The maximum transmission range for both the WLV 1000 and WLV500 will be achieved when there is a clear line of sight between the transmitter and receiver antennas The best reception will occur if all antennas are elevated a minimum of 8 to 10 feet above level ground If there are moving objects between the antennas suchas traffic on the road the antennas should be elevated a minimum of 8 to 10 feet above such objects to obtain the best reception For units that have a detachable antenna on the receiver only a high quality low loss 50 ohm cable RG 8 or similar should be used for situations requiring a longer interconnection between the receiver and antenna It is also best to position the antenna such that the front of the antenna is directly facing the transmitter and is not obstructed by any metalli
9. operates in another channel Multipath Reception Ghosting Since the WLV500 Series employs FM modu lation of the data onto the carrier it is less susceptible to multipath interference than com mercial broadcast systems that employ ampli tude modulation The WLV500 system also employs circularly polarized antennas that provide some immunity to multipath reflec tions However multipath interference can occur and depends on antenna location rela tive to nearby metallic objects and on the direction the antenna is facing The receiver antenna provides the most gain and highest multipath immunity when it is directly facing the transmitter If multipath interference oc curs it can usually be eliminated by relocating or reorienting the receive antenna a small distance less than 1 2 feet Due to the difficulty of predicting the suscep tibility of any one application to the transmis sion limitations described above it is gener ally recommended that site testing occur prior to installation Consult your customer service representative to obtain further information Pelco Manual C901M 1 94 5 0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on FT FR8000 Series fiber optic products e Three years on Genex Ser
10. rent lt 350 mA transmitter should be connected to a video Terminal Barrier Strip Reverse Polarity Protection monitor 2 The port labeled OUT of the Coaxitron Sys tem 2000 receiver should be connected to the BNC connector labeled DATA OUT of the WLYVS5O0OORX control link receiver Mechanical Weight Each Unit lt 16 oz Dimensions D x W xH Inches 3 The wall mounted power supplies 15 VDC included in the system should be connected to Transmitter w Antenna the power strips of each unit labeled 11 16 5 00 x 3 50 x 1 80 V The striped lead with a red connector should be connected to the positive termi Receiver w o Antenna nal and the ground lead with the black connec 5 60 x 3 50 x 1 30 oD tor should be connected to the negative terminal The power supplies should then be plugged into a 120 volt AC power outlet 2 Pelco Manual C901M 1 94 4 The units should become fully operational within two minutes after DC power is con nected after which adjustments can be made 4 2 ANTENNA POSITIONING AND MOUNTING Although the video and data systems operate at different frequencies out of band emissions exist due to the wideband transmission characteristics of the video sig nal At the maximum operating range these out of band video emissions can have a higher signal strength than the received data signal due to the close proximity of the WLV1000TX to the WLV500RX This will ja
Download Pdf Manuals
Related Search