Pelco SS3000 User's Manual
Contents
1. 12 Clean the acrylic lower dome as necessary to maintain a clear picture Be careful not to scratch the surfaces of the dome Exterior Surface Clean the dome s exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic plastic Either liquid or spray cleaner wax suitable for fine furniture is acceptable Interior Surface Except Chrome Clean the same as the exterior surface Interior Surface Chrome The inside surface of a chrome dome is easily scratched Use the following precautions to maintain the dome s surface a b Always handle the dome from the outside of its circular flange Never touch the coated inside surface The acid in your fingerprints will even tually etch the coating if the fingerprints are not carefully removed according to the recommended cleaning procedure in item e If dust or other contaminants accumulate on the dome s interior remove the debris with compressed air Compressed air cans are available from photo graphic equipment or electronic supply dealers If heavy residue accumulates and cannot be removed with air pressure rinse with water and immediately dry with air pressure so that water spots will not remain Avoid wiping the coated surface with direct hand pressure it will eas ily abrade unless extreme care is taken Once scratched the dome cannot be recoated If internal wiping is necessary avoid hand rubbing Instead make a wick as fol2. The SS3000 enclosure is designed to be suspended from a suitable length of 1 1 2 pipe threaded at both ends This pipe can be interfaced to either a Pelco MRWA wall adapter MRCA ceiling adapter or coupled to a longer length of pipe see Figure 3 CEILING MOUNT STRUCTURAL CEILING MOUNTING CEILING MOUNT TEE UNION 7 DROP CEILING MOUNTING WALL MOUNTING Figure 3 Mounting Configurations PELCO Manual C428M B 2 98 3 4 1 Ceiling Wall Mounting NOTE 77e Schneider ring referred to in these instructions is a 10 inch black aluminum ring designed to fif around the square portion of the up per dome Use of this ring helps to camouflage movement of the dome NOTE Disregard step 3 if using the PTZ280 24SL pantit NOTE When installing a PTZ80 Z4SL partit with the slip ring option you will need to remove one 1 of the 1 4 20 fasteners holding the mount ing flange to the SL2800 bracket Pivot the partit assembly to one side to allow the connector and cable to pass through After the connection is made pull the connector back up into the pipe and reattach the mounting fange NOTE Mhen mounting a long cam eralens assembly 13 to 15 into a SS3000 enclosure it must be mounted to the partit backwards so the lens s to the rear of the pantift This is fo allow full downward tilt of the long lens This must also be taken Into consideration when wiring the unit as the motions
3. U L 94HB rated ABS plastic Lower dome Acrylic hemisphere with distortion free viewing window with light attenuation factor of 1 f stop SS30 SS3000 or mirrored lower dome with 2 f stop 883002 Rotates with pan and tilt camera and lens Environment Indoor 32 to 120 F 0 to 48 89 C Unit Weight 6 Ib 2 72 kg approximate Dimensions See Figure 7 Design and product specifications subject to change without notice This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment 20 00 50 80 24 00 60 96 NOTE VALUES IN PARENTHESES ARE CENTIMETERS ALL OTHERS ARE INCHES Figure 7 SS30 SS3000 Dimension Drawing PELCO Manual C428M B 2 98 15 7 0 WARRANTY AND RETURN INFORMATION Pelco the Pelco logo Camclosure Esprit Genex Legacy and Spectra are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 1998 Pelco All rights reserved 16 WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on G
4. The SS3000 Series has been engineered for ease of installation serviceability and relocation The lower dome quickly and easily detaches from the upper dome for convenient access to the camera and pan tilt 2 1 MODELS SS30 Full sphere enclosure with black opaque lower dome with smoked viewing window and fixed camera mount SS3000 Full sphere enclosure supplied with a black opaque lower dome with smoked viewing window Fixed camera mount not supplied This dome is designed for use with an optional pan tilt assembly PT280 series S3002 Same as SS3000 except supplied with mirrored lower dome with 2 f stop light loss 2 2 OPTIONS PT280 24P Light duty indoor pan tilt 24 VAC PT280 24P PP Same as PT280 24P except has preset position PP option PT280 24SL Light duty indoor pan tilt with continuous 360 operation PT280 24SL PP Same as PT280 24SL except has preset position PP option MRWA Wall mount adapter MRCA Ceiling mount adapter 4 PELCO Manual C428M B 2 98 3 0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned for credit or repair 3 4 CONDUCTOR AND CABLE REQUIREMENTS 3 2 WIRING INSTRUCTIONS NOTE you are not using the C1906 C1906 PP C1925 or C1925 PP pretested cable you must reverse the left right and up down function pins as shown in Figure 7 PELCO Manual C428M B 2 98 Before installing the pan and tilt determine the conductor requirements and
5. parts recommended by Pelco After replacement repair of this units electrical components conduct a resis tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The installation method and materials should be capable of supporting four times the weight of the enclosure pan tilt camera and lens combination The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit maintenance instructions in the literature accompanying this i This symbol indicates that there are important operating and unit CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please thoroughly familiarize yourself with the information in this manual prior to installation and operation PELCO Manual C428M B 2 98 2 0 DESCRIPTION Pelco s SS30 SS3000 series is a full sphere discreet surveillance enclosure de signed to be suspended from a ceiling and to complement the interior decor of businesses hotels and offices The smoked finished lower dome effectively camouflages a CTTV security surveillance system without compromising the quality of the video picture An op tional mirrored lower dome SS3002 is available
6. will be reversed NOTE 77e small hole in the upper dome for safety chain attachment should be positioned at the back con nector end of the camera PELCO Manual C428M B 2 98 1 Select an appropriate length of 1 1 2 NPT pipe for the mount you have se lected Once the mount is installed insert and tighten the pipe to approxi mately 30 ft Ib then tighten the 8 32 screw in the pipe nut to lock the pipe threads Slide the black 10 OD Schneider ring over the pipe and then slide the upper dome onto the pipe and lock it out of the way with a suitable retainer Screw the mounting flange item 4 Figure 5 onto the pipe and tighten to approximately 20 ft Ib Tighten the 8 32 screw in the pipe nut to lock the pipe threads refer to Figure 4 Align the three hole pattern in the pan spindle PT280 24P with the holes in the lower bracket item 5 Figure 5 and attach with 1 4 20 x 5 8 hex head bolts and lock washers provided Tighten firmly Assemble the lower bracket and pan tilt to the mounting flange item 4 Figure 5 using 1 4 x 5 8 hex head bolts flat washers and hex nuts provided Attach the upper drive bracket item 3 to the bottom spindle side of the pan tilt using four 4 10 32 x 1 2 pan head screws and lock washers pro vided Refer to Figure 5 for proper orientation Feed the main cable from the control or receiver through the center of the 1 1 2 pipe and connect it to the cable of the pan tilt Pull th
7. SS30 SS3000 SS3002 Dome Enclosures Installation Operation Manual C428M B 2 98 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 CONTENTS Section Page aRoumelzivzir in 3 1 14 IMPORTANT SAFEGUARDS AND WARNINGS se 3 2 0 DESCRIPTION i eiie esee e etd eet Pe ER EFIE RE EE TE EY COP FEL ELO ees 4 2 1 MODELS 2 2 OPTIONS 3 0 INSTALLATION ee cp cei fttt etc tme 3 1 CONDUCTOR AND CABLE REQUIREMENTS 3 2 WIRING INSTRUCTIONS eee as 3 3 CONNECTOR ASSEMBLY ricette et e e ied 34 MOUNTING o then cei e tib teh egi c cei des 3 4 1 Ceiling Wall Mounting 3 5 ADJUSTMENTS eee oec ben t D t ede deii 4 0 MAINTENANGE icit rre retreat tet re ERE EGRE 12 5 0 MECHANICAL PARTS LIST iih ad th estne e n 18 6 0 SPEGIFICATIONS cient tor rco t ert rina ern tert Ea EE se CE YE HEC ena pa 14 7 0 WARRANTY AND RETURN INFORMATION eeeeee 16 LIST OF ILLUSTRATIONS Figure Page 1 PT280 24P Wiring Schematic ee 6 2 Connector Assembly m 3 Mounting Configurations E 4 Eocking the Pipe NUL i ice ape petrae Ere rh o Fara rere EERS 9 5 SS3000 Exploded Assembly Diagram eene 10 6 PT280 24P Limit Locations 7 S30 SS3000 Dimension Drawin
8. boot encases the cable and forms a good seal 3 Strip back the cable jacket approximately 1 1 4 inches 3 2 cm and separate the individual conductors item 3 4 The contact pins supplied with the mating connector are the crimp type which may also be soldered if you so desired item 4 5 After crimping or soldering the contact pins to the conductors push them into the proper holes in the connector until they snap in place 6 Slide part A of the cable clamp toward the connector and screw the parts together Attach part B item 1 onto part A and connect both parts with the NOTE Contacts cannot be removed a screws provided from the connector without the use of the appropriate AMP extraction too 7 Connect the cable assembly to the unit and seat the connector by twisting the Which is available from Pelco locking collar until it snaps into position threaded end of cable clamp FLEXIBLE RUBBER BOOT P s 1 8 STEPS 3 7 CRIMP INSULATION OUTSIDE JACKET STRIP 1 OF CABLE ITEM 5 DETAIL FRONT VIEW FRONT VIEW FRONT VIEW 37 PIN CONNECTOR 28 PIN CONNECTOR 16 PIN CONNECTOR THE MOST COMMONLY USED CONNECTOR PIN OUT CONFIG URATIONS ARE SHOWN HERE REFERENCE THE CONNECTOR DRAWING APPLICABLE TO 1 YOUR SITUATION FRONT VIEW FRONT VIEW 14 PIN CONNECTOR 9 PIN CONNECTOR Figure 2 Connector Assembly PELCO Manual C428M B 2 98 7 3 4 MOUNTING
9. d in Section 3 1 The fol lowing are some recommended common installation practices 1 Always use jacketed stranded multi conductor interconnecting cable between the control and the pan tilt with additional conductors than needed for future servicing and or additions 2 Always use color coded conductors for ease of wiring and to identify functions at a later date 3 Keep a wiring diagram with the system for later use and reference INPUT CONNECTOR VIDEO SHIELD YEL CAMERA WHITE J2 AERE UE UNE NS ENS CONNECTOR CAPACITOR 15 MFD 100V CAPUO015 0 100N PAN MOTOR 2508001 EDU WEEN TILT MOTOR PS78001 CONNECTOR CONMAB6100 ZOOM W RED CONNECTOR PINS CON66102 7 LENS COMM W ORG SWITCH SWHSM1 SFTY GRND amp GRN INPUT CONNECTOR CON206044 1 MATING CONNECTORASSY CONA14S ACTUATOR SWIJS138B LENS MATING CONNECTOR CONMAS6100 Figure 1 PT280 24P Wiring Schematic 6 PELCO Manual C428M B 2 98 3 3 CONNECTOR ASSEMBLY Installation and or testing will require you to assemble the connector parts pro vided Fabricate the interconnecting cable according to the following steps refer ence Figure 2 1 Slide part A of the cable clamp item 1 over the end of the cable item 1 part C with the threaded end of the cable clamp facing the connector item 5 2 Ifthe cable has a diameter less than 1 2 inch 1 3 cm slide the rubber boot item 2 over the end of the cable and pull through the cable clamp to so that the
10. e cable and con nector back up into the pipe so that it does not get caught on the rotating parts Install the camera lens assembly onto the tilt table of the pan tilt Connect the proper cables camera lens function Remove the retainers from the upper dome and lower it until it seats itself on the upper drive bracket 1 1 2 NPT PIPE PIPE NUT Figure 4 Locking the Pipe Nut CAUTION 77e ower dome will shatter if dropped Always operate with the safety chain at tached Do not rotate par tilt by hand Rotate by con troller only NOTE 77e Schneider ring is not shown in this diagram It is de signed to fit over the square por lion of the upper dome item 1 PT280 24SL 10 11 Turn the system on and rotate the pan tilt Check for cable interference Tilt the camera up and down and check for clearance of all moving parts After all tests have been done and the system is functioning properly attach the safety chain to the upper dome with the fasteners provided Install the lower dome being careful to align the viewing window Check for sufficient clearance between the lens and the lower dome MOUNTING COLUMN 6 UPPER DOME 1 UPPER BRACKET 3 MOUNTING BRACKET 4 LOWER BRACKET 5 en CHAIN 10 LOWER DOME 2 Figure 5 SS3000 Exploded Assembly Diagram 10 PELCO Manual C428M B 2 98 3 5 ADJUSTMENTS CAUTION Do not at To adjust the pan tilt limits perform the fo
11. enex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Sixmonthsonall pan andtilts scanners or presetlenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or applicat
12. g LIST OF TABLES Table A B SS3000 Exploded Assembly Diagram Corresponds to Figure 5 13 Parts for SS30 Fixed Mount Dome Only Not Shown in Figure 5 13 REVISION HISTORY Manual Date Comments C428M C428M C428M B 3 87 Original version 5 90 Rev A Revised Section 4 3 Connector Assembly procedures Section 4 5 Adjustments for addition of fixed limit stop and Section 6 0 Mechanical Part List Figure 1 parts listed revised 6 95 Rev B Revised Section 4 1 Conductor amp Cable Requirements cable requirements and distances Section 4 4 1 Ceiling Wall Mounting instructions for Schneider ring and Section 6 0 Mechanical Parts List updated parts Figure 1 revised to show safety ground wire as green Revised Section 6 0 Mechanical Parts List regarding part numbers for lower domes Added item 14 Revised Section 4 0 Maintenance Changed manual to new format 8 96 2 98 PELCO Manual C428M B 2 98 1 0 GENERAL 1 1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture Only use replacement
13. ion made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating tothe Products shall not exceed the price paid by the Dealerto Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned f
14. length of cable you will need to run based on the following Conductor requirements for the pan and tilt are as listed below plus coax cable PT280 24P PT280 24SL PT280 24P PP PT280 24SL PP Pan Tilt Lens Cam AC 5 grnd 4 2 9 grnd 8 2 10 grnd 8 2 Camera power lens functions and video are fed through the input connector on the base of the pan tilt The following are the cable requirements for the PT280 series pan and tilts 5 Conductor 20 Awg 110 ft 33 53m 18 Awg 180 ft 54 86m 16 Awg 290 ft 88 39m Using 2 wire common 6 Conductor 210 ft 64 01m 330 ft 100 58m 530 ft 161 54m To install and test the pan tilt you will need to assemble the connector parts pro vided Refer to Section 3 3 for connector assembly The PT280 series pan tilts are prewired for all control functions pan tilt motorized zoom lens 24 VAC camera power and video All connections are made at the input connector eliminating the need for wiring harnesses made in the field When using Coaxitron Control Systems consider using the C1906 C1906 PP C1925 or C1925 PP factory assembled pretested cables which are wired for inverted applications Wire the control cable per the wiring diagram provided in the PT280 Series Pan Tilt manual C324M for the specific pan tilt you are using The PT280 24P basic pan tilt wiring diagram is included in this manual for reference only Cable distances should not exceed the distances specifie
15. llowing steps Refer to Figure 6 for limit tempt to adjust limit stops stop locations when partit is in opera tion Damage to the equip 1 Factory pan limits are set to 0 355 and tilt limits at 45 Pan to the right using ment can result Also do the joystick control until the desired RIGHT pan limit is reached not operate equipment f age 2 Adjust the pan limit stop until the actuator clicks Lock the limit into position without limit stops Do not J i TIER remove or reposition fixed 3 Pan to the desired left position adjust the pan limit stop until the actuator limit stop on the PT280 clicks and lock into position 24P pan tilt DAMAGE WILL OCCUR 4 Pan to the left and right to verify exact positioning and tighten both stops se curely 5 Remove the left cover plate by removing the two screws for access to the tilt limit stops 6 Loosen the screws and move the DOWN limit stop to the furthest position Using the joystick control tilt the unit to the desired down position 7 Move the DOWN limit stop until the actuator clicks Lock the limit into position 8 Adjust the UP limit stop in the same way 9 Tilt up and down to verify exact positioning and tighten both stops securely TILT DOWN LIMIT STOP TILT UP LIMIT STOP PAN LIMIT SWITCH ACTUATOR PAN RIGHT LIMIT STOP PAN LEFT FIXED LIMIT STOP LIMIT STOP Figure 6 PT280 24P Limit Locations PELCO Manual C428M B 2 98 11 4 0 MAINTENANCE
16. lows Use a very soft paper towel Roll a section into a tightly wound tube Tear the tube in half and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with water Hold the dome with its opening facing downward and wipe the interior of the dome with the wet end of the wick Use a circular motion starting from the outside and spiraling into the center Use a new wick for each two passes over the dome PELCO Manual C428M B 2 98 5 0 MECHANICAL PARTS LIST Table A SS3000 Exploded Assembly Diagram Corresponds to Figure 5 Dome upper Dome lower smoked SS30 SS3000 Dome lower chrome SS3002 Bracket upper drive SS3000 SS3002 Bracket mounting hanging weld assy Bracket lower SS3000 SS3002 Pipe mounting Not used Not used Velcro black 5 8 wide x inch not shown Chain 16 single jack x 6 length Trim edge black chrome not shown Snap body for chain assembly not shown Ring Schneider 10 OD x 9 812 ID not shown Velcro black 5 8 wide x inch not shown 8300010000 8300010001 S331100 830004000COMP S300031001WA PM200C4000COMP SS34002COMP TV10002 SB2511000 88300010004 SB2511001 830004100COMP TV10003 Part number is for the dome only To order a complete lower dome assembly specify the part numbers S830004003COMP smoked and SS334200COMP chrome These part numbers include items 2 10 12 and 14 Table B Par
17. or credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 PELCO Manual C428M B 2 98
18. ts for SS30 Fixed Mount Dome Only Not Shown in Figure 5 PELCO Manual C428M B 2 98 Tilt table fixed black Pedestal spacer black Dome support bracket Fixed bracket black Pedestal mount fixed CM14004100BCOMP CM30004001 COMP CM30024000COMP EM14004001BCOMP PM74000COMP 13 6 0 SPECIFICATIONS 14 ELECTRICAL Input voltage Power Requirements Pan Tilt Connectors Pan Tilt Lens Video Camera Power Motors Limit Switches Conductor Requirements MECHANICAL 24 VAC required for pan tilt Starting 47 amp 11 2 vA 56 amp 13 5 vA Running 31 amp 7 5 vA 38 amp 9 2 vA AMP CPC type mate supplied Hirschmann MAB6100 BNC Spade lugs Two phase induction type instantaneous reversing 5 amp external adjustment See Section 3 1 for detailed specifications refer to PT280 series product manual C324M Pan Pan Speed Tilt Tilt Speed Max Load Dome Drive Max Camera and Lens Length Movement in horizontal plane PT280 24P 0 355 PT280 24SL 0 360 12 sec 1 no load condition x90 movement in vertical plane 3 sec 5 no load condition 15 Ib 6 81 kg at 5 from tilt table surface to center of gravity Lower dome mounts into upper dome with Velcro fasteners complete assembly is driven by pan tilt 16 0 inches 40 6 cm including BNC connector PELCO Manual C428M B 2 98 GENERAL Construction Upper dome Black
Download Pdf Manuals
Related Search