Pelco CC3320-3 User's Manual
Contents
1. Dimensions 4 82 L x 2 57 W x 2 34 H inches 12 25 L x 6 55 W x 5 95 H cm Supply 11 40 VDC or 14 30 VAC 50 60Hz 230 VAC 10 15 50Hz 4 Modes Auto Tracing ATW Indoor Outdoor and Fluorescent Page 2 Installation Instructions CC3320 and CC4620 Cameras PRODUCT SAFETY AWARNING e Ensure installation and servicing is carried out by qualified personnel e To prevent fire or shock hazard do not expose this appliance to rain or moisture e Isolate from the supply circuit before any servicing e Installation method and materials must be capable of supporting four times the total weight of the unit e Power supply cords must be connected as defined in national electrical codes of practice for Class 1 earth protected equipment e Low voltage cameras must be connected as defined in national electrical codes of practice for Class 2 protection of double or reinforced insulation e Safety critical components must only be replaced with recommended parts A The maximum load on the rear auto iris connector must not exceed 50 mA The maximum load on the direct drive connector must not exceed 25 mA REGULATORY NOTICES Federal Communications Commission Part 15 Digital devices This Device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must ac2. invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return on warranty shipments shall be the same or equal to the method by which the item was received by Pelco In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair Goods returned should be clearly identified with the assigned CA RA number and freight should be prepaid All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Ship freight prepaid to e Pelco 3500 Pelco Way Clovis CA 93612 5699 or e Pelco c o American Overseas Airfreight 320 Beach Road Burlingame CA 94101 if shipped outside the United States REVISION HISTORY Manual Date Comments C1932M 8 99 Original version 05 00 Addresses amended Pelco and the Pelco logo are registered trademarks of Pelco Copyright 1999 Pelco All rights reserved Pelco Manual C1932M 5 00 Rev 3
3. CC3320 CC4620 Series Color Cameras Installation Operation Manual C 1932M 05 00 CE Pelco 3500 Pelco Way Clovis e CA93612 5699 USA Pelco Online http www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 DataFAX 1 559 292 0435 Pelco Europe BV Dillenburg Center Dillenburgstraat 5F 5652 AM Eindhoven The Netherlands Tel 31 40 251 9870 or FAX 31 40 251 9835 CC3320 and CC4620 Cameras Installation Instructions INTRODUCTION These instructions cover Pelco s CC3320 and CC4620 Series cameras Read all of these instructions Use them to install your camera and have them available for its lifetime Refer to Table A for the camera models and their features All cameras in the range are fitted with a direct drive DD lens connector have adjustable back focus and accept C and CS lenses TABLE A CC3320 2 CC3320 3 CC3320 2X Color PAL NTSC Resolution TVL Sensitivity lux f1 2 CCD Sensor size Sony HyperHAD CCD Adjustable Gamma 0 45 and 1 0 Automatic Gain Control AGC AGC on off Backlight Compensation BLC BLC on off Manual Shutters Flickerless Electronic Iris El El on off 4 White Balance modes Auto Iris connection Line lock with phase adjust AC only CC4620 2 CC4620 3 CC4620 2X
4. cept any interference that may cause undesired operation CERTIFICATIONS This product meets the requirements of the following standards Electromagnetic Compatibility EN55022 1995 limits and methods of measurement of radio disturbance characteristics of information technology EN50082 1 1992 Generic immunity standard Comprising IEC 1000 4 2 1995 Electrostatic discharge IEC 1000 4 3 1995 Radiated electromagnetic fields IEC 1000 4 6 Immunity to conducted disturbances induced by radio frequency fields IEC 1000 4 4 1995 Fast transient bursts Safety EN 60950 1992 Safety of information technology equipment including electrical business equipment DECLARATIONS The manufacturer declares that the equipment supplied with this manual is compliant with the EMC directive 89 336 EEC and the low voltage directive 73 23 EEC and CE marked accordingly Page3 CC3320 and CC4620 Cameras Installation Instructions CAUTIONS A CAUTION In order to avoid damaging your camera note the following points 1 The camera has threaded mounting points on the top and bottom of the case Only use a standard photographic mounting bolt with a 1 4 20 UNC thread 2 Before fitting the lens make sure that its back will not touch the CCD sensor or associated components when fully installed 3 Do not touch the image surface of the sensor If the sensor is accidentally touched only clean it using isopropanol 4 Do not expose the sensor to direct s
5. ches 5 and 6 Choose Fixed or Adjustable Both settings are line locked however the Adjustable setting allows 120 phase adjustment via the potentiometer located on the rear of the camera The Adjustable mode should be used when cameras are connected to different AC power supply phases Default setting is Fixed SYNC Synchronization The Synchronization feature is selected using DIP switch 6 Choose LL Line Lock or Internal LL locks the frame rate to the power supply frequency so that cameras are triggered at the same point on the power supply AC cycle Internal locks the frame rate to the internal oscillator of the camera The default setting is LL 12 a Auto Indoor HH Fluorescent aA Outdoor 3 Normal 0 45 3 F Linear 1 0 4 off 4 Hon Fixed Adjustable Oo Lo 5 i 5 s 6 l Internal 6 E L Page 5 CC3320 and CC4620 Cameras Installation Instructions FUNCTION SWITCHES Shutter speed switches Shutter speeds are selected with DIP switches 8 9 and 10 DIP switch 7 must be down to enable manual shutter speed selection For El BLC and Flickerless functions switch 7 must be up 7 8 910 7 8 910 7 8 910 7 8 910 EEEH 1 10 000 Mg 1 2 000 EHAN 1 500 Meg 1 125 EEH 1 4 000 Egi 1 1 000 Egg 1 250 Bigg 1 50 El Electronic Iris 7810 The El Electronic Iris feature compensates for excessive light level by automatically WHH E On adjusting shutter speed Selecting Electronic Iris disables
6. ge6 Installation Instructions CC3320 and CC4620 Cameras LENS CONNECTION Fixed and manual iris lenses for indoor use only require no wiring connections Auto lris Lenses Connections for auto iris lenses are located on the rear of the camera Connect auto iris lenses to the 3 terminal connector according to the diagram below Direct Drive Connect DD lenses to the female 4 pin socket on the side of the camera If the lens does not have a DD plug fitted then wire the lens to a suitable plug in accordance with the diagram below e 1 Damp 5 t Lens positive supply 7 im m Lens ground os z o y V Video drive signal nae eee 2 4 4 Drive Auto lris Lens Connections DD Lens Connector LENS SETUP PROCEDURES For manual or fixed iris lenses set the El switch and AGC switch to ON Auto lris Lenses Switch the El andAGC OFF Refer to the lens instructions and adjust the lens for the optimum picture video output level of 1V peak to peak Switch the AGC ON Direct Drive Lenses Where fitted switch the El and AGC OFF Use an appropriate screwdriver to turn the lens level potentiometer under the hinged flap fully clockwise Next slowly adjust the potentiometer counterclockwise until the optimum picture is obtained video output level of 1V peak to peak Switch the AGC ON FOCUS ADJUSTMENT The back focus adjustment screws are located on the top and side of the case at the front of the camera and shou
7. ld be adjusted using an appropriate screwdriver Do not over turn the back focus mechanism Fixed Lenses Set the lens focus to infinity and view an image greater than 6 5 feet 2 m away Focus the image using the back focus screw Set the lens focus as required Manual Iris Lenses Open the iris fully and set the lens focus to infinity View an image greater than 6 5 feet 2 m away Focus the image using the back focus screw Set the lens focus and iris as required Auto iris and Direct Drive Lenses Fully open the iris by covering the lens with a suitable neutral density ND filter Set the lens focus to infinity View an image greater than 6 5 feet 2 m away Focus the image using the back focus screw Remove the ND filter and set the lens focus as required Page7 FOCUS ADJUSTMENT Zoom Lenses Set the lens focus to infinity and fully open the iris by covering the lens with a suitable neutral density ND filter Zoom out to the widest field of vision and view a distant object Adjust the back focus screw until the object is in focus Next zoom fully in and adjust the lens focus until the object is again focused Repeat these steps until the full zoom range may be viewed with the minimum loss of focus SYNCHRONIZATION Cameras that operate from AC power supplies are line locked for a supply frequency of 50 Hz 60 Hz for NTSC versions If the supply frequency is unstable then disable the line lock by setting the SYNC swi
8. manual shutter speed 7 selection The Electronic Iris setting must not be used when the camera is set to fal EI Off Flickerless mode The default setting is Electronic Iris ON BLC Back Light Compensation The BLC Back Light Compensation feature compensates for back lit scenes by Pp enhancing objects in the center of the scene which would previously have been WE BLC On in silhouette Select ON or OFF using the BLC switch Default is OFF BLC will only e function with a manual iris lens when the Electronic Iris feature is switched on For a direct drive and auto iris lenses BLC will still function even though the Electronic Iris feature is switched off Flickerless The Flickerless setting can reduce the flicker caused by certain lighting conditions EIE On Choose between ON or OFF The default setting is OFF Note thatthe Electronic Iris 7 setting must be off for correct operation of the Flickerless function oa Off LENS SELECTION Suitable lens types are C and CS mount in fixed iris manual iris auto iris or direct drive versions Sizes are shown below Cameras are factory set for CS mount lenses If using a C mount lens rotate either of the back focus screws approximately 30 turns counterclockwise before installing the lens Lens size 1 3 1 2 2 3 T o 3 A t 3 oO e e e e e CC4620 3 CC4620 2x e CC3320 2 e e CC3320 3 e CC3320 2X Pa
9. r to the BNC socket marked VIDEO OUT on the rear of the camera Page4 Installation Instructions CC3320 and CC4620 Cameras FUNCTION SWITCHES On the side of the camera is a hinged flap The hinged flap covers a lens level potentiometer and 10 function switches Mounting boss Back focus adjustment Function switches DD lens level adjustment connector Color Balance There are four color balance modes selected by DIP switches 1 and 2 For the majority of applications the Auto setting will provide excellent color rendition and is the default setting For applications where the illumination is predominantly daylight the Outdoor setting may provide improved color rendition over Auto Where a mixture of illuminations such as tungsten fluorescent and daylight exist the Indoor setting may provide the best color rendition Where fluorescent lighting is predominant use the Fluorescent setting Gamma There are two different levels of Gamma selected by DIP switch 3 Choose between Normal 0 45 to provide increased visibility in dark areas of the scene or Linear 1 0 The default setting is Normal AGC Automatic Gain Control The Automatic Gain Control feature can improve picture quality when levels of illumination are low Select ON or OFF using DIP switch 4 For most applications the AGC should be ON and is the default setting LL PH Line Lock Phase Adjust The Line Lock Phase Adjust feature is selected by DIP swit
10. tch to Internal WARRANTY AND RETURN INFORMATION Pelco will repair or replace without charge any camera proved defective in material or workmanship for a period of two years after the date of shipment Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco
11. unlight as this may impair the performance of the camera POWER SUPPLY The CC3320 and CC4620 Series cameras are available in 230 VAC or 11 40 VDC 14 30 VAC low voltage types The voltage required to operate the camera is clearly marked on the rear panel of the camera The green POWER LED on the rear panel indicates that power is connected Power the low voltage cameras only from a class 2 isolated power supply The power consumption is less than 5 Watts 230 VAC Power Supply Cameras that are intended to operate directly from 230 VAC are fitted with a non detachable power supply cord The voltage of operation is clearly marked on the rear panel of the camera Generally this is 230 VAC 10 15 at 50 Hz 60 Hz for NTSC versions Refer to the wiring instruction label attached to the supply cord and terminate the cord with the appropriate circuit with a 3A fuse CAMERAS MUST BE CONNECTED TO A PROTECTIVE EARTH GROUND Ensure that a secure means of isolation from the AC power is provided for the camera in accordance with the national wiring regulations of the country of installation Auto switching power supply Cameras fitted with an automatic selecting power supply operate between 11 40 VDC and 14 30 VAC Connections and polarity are indicated above the screw terminals on the rear panel The power supply must be a class 2 isolated type VIDEO CONNECTIONS To obtain a video output connect a video coaxial cable terminated with a 75Q BNC connecto
Download Pdf Manuals
Related Search