Pelco C1005M-G User's Manual
Contents
1. INSTALLATION OPERATION ICI1000PIM Personality Interface Module C1005M G 10 02 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully The following items are supplied 1 ICI1000PIM Personality Interface Module 1 RJ 14 cable for Inter Check and the DX2000 DVR 1 RJ 45 coupler for the DX2000 DVR DESCRIPTION The ICI1000PIM Personality Interface Module PIM is a data protocol translator that translates data from cash registers and other devices for use with Pelco s Inter Check or DX2000 Digital Video Recorder DVR Inter Check is an automatic text insertion system that displays the data on a CCTV monitor The DX2000 records video and transaction data and lets the user view video and its associated data if applicable on a PC personal computer C1005M G 10 02 INSTALLATION NOTE The information in this manual is for PIM software version 4 02 and above INSTALLATION FOR INTER CHECK C1005M G 10 02 Refer to the ICI10005 Inter Check manual as you install the ICI1000PIM 1 2 Configure DIP switch bank 1 on the PIM refer to Configuring DIP Switch Bank 1 section Configure DIP switch bank 2 on the PIM refer to Configuring DIP Switch Bank 2 section Locate the 16 pin connector on your register interface Plug the register interface connector into the PIM Plug one data cable connector into the data connector in the PIM Connect the other end of the data cable in one of the following ways2. a If the Inter Check and the PIM are within 6 feet 1 8 m of each other modify the cable as follows Refer to Figure 1 and slit the jacket to expose the wires Cut the red and green wires To ensure the cut wires will not contact each other either remove a section of the red and green wires or in case you want to reconnect the wires later tape one end of the cut wires Plug the cable into the Inter Check b Ifthe Inter Check and the PIM are more than 6 feet 1 8 m apart you must use the wiring kit Refer to Figure 2 The wiring kit is supplied with the ICI1000SE and ICI10008SI Mount the PIM inside or near the cash register or other device Depending on the application you may need to use double sided tape to secure the ICI1000PIM to the mount location Power up the Inter Check To set all Inter Check communication parameters to the specific values needed to communicate with the ICI1000PIM module do the following a Enterthe main screen by pressing the ESC key and then the ENT key on the keypad b Once the main screen is present press the 6 key selection Diagnostics and then the 8 key DL PIM Default Load C Press the 8 key until the loaded message appears on the screen and then press the ESC key until the unit is reinitialized Refer to the C1000M B manual if more detailed information on this procedure is required Power up the register or other device Connect the power plug into the PIM and plug the wa
3. cable is a straight through cable The PIM will not work with a flipped cable Connect the other end of the data cable to the RJ 45 coupler provided Connect a straight pinned CAT 5 cable from the coupler to the DX2000 DVR or DX2000DH Data Hub Mount the PIM near the register interface Depending on the application you may need to use double sided tape to secure the ICI1000PIM to the mount location On the Communication Type Setup tab of the DX2000 s Data Interface configuration screen select Pelco PIM as the communication type in the Device Type pull down menu Refer to the DX2000 Installation Operation manual C690M for more information Power up the register Interface Connect the power plug to the PIM and plug the wall mount transformer into power This powers up the PIM Upon PIM power up a message that matches your PIM switch settings for your register interface type will appear in the Live Data screen for the selected data device A PIM version number is also displayed This message indicates the DX2000 and PIM are communicating properly REGISTER INTERFACE 6 FOOT RJ 14 CABLE SUPPLIED RJ 45 COUPLER USER SUPPLIED STRAIGHT PINNED CAT 5 CABLE DX2000 REI E BELT L2 ES EET MON piep pre OUT C c NCN NCN 9 0 0 Figure 3 Connecting the Components for DX2000 CONFIGURING DIP SWITCH BANK 1 The switches in this bank serve several purposes Selections in
4. patddps p DATA CHECKER ALPHA 2 3 Printer ICL MT20001 With Alpha 2 3 Printer DRESSER WAYNE Printer Serial EPSON Squirrel ESPER 7100 Drum Printer 4 ESPER 7540 7810 Dot Matrix Printer perpe FUGITSU ATRIUM Series with Bar 200 Printer eod cq GILBARCO TCR G2 Parallel Printer au eese HUGEN SWEDA SWEDA 5436 Serial Printer fossi IBM Model 1 2 Printer IBM4683 4684 with Model 1 or Model 2 Printer mego IBM Model 3 amp 4 Printer IBM4683 4684 IBM4693 4694 with Model 3 Printer p e ICL 200 PTR ICL STORE MASTER 9518 200 FE ae ICL DATA CHECKER MDL 1600 1700 1800 Multidrop Connection dus donee ICL DTS 2000 2100 2200 EPSON 220 AF Dot Matrix Printer TUE eas ICL DTS 2000 2100 2200 EPSON 220 F Dot Matrix Printer OPE REN JCM GOLD 2200 Drum Printer MICROS 2700 3700 FERT NN NCR 2127 With V3 MULTIFINCITON Printer Serial NCR 2121 Printer Serial NCR 2113 Printer Serial PEUT NCR ANSWER Printer SINGLE NCR 1255 2140 2151 2152 2154 2157 2160 2552 2557 NCR 5300 SASI 1028 0LD STYLE Printer MERIT REGISTER SYSTEMS ee NCR ANSWER Printer DUAL NCR 2126 ueque su NCR 7150 5001 Printer 7000 SERIES REG POE AE NCR Register with RS 485 Printers 7150 7156 7193 and 2207 NIXDORF OMRON RS5550 RS5560 Dot Matrix Printer ie epee tee OMRON 4510 4541 Dot Matrix Printer 2 T OMRON R 3410 Dot Matrix Printer diede OMRON 4041 4043 Dot Matrix Printe
5. 0 FDS 30 DPR 370 374 Dot Matrix Printer TEC 1400 1600 1700 1900 FSD 30 DPR 370S Dot Matrix Printer TEC FT77 Printer Serial Interface TOKHEIM C1005M G 10 02 9 SPECIFICATIONS ELECTRICAL Power Input Voltage Connectors DIP Switches GENERAL Construction Environment Operating Temperature Weight Dimensions 120 VAC 60 Hz to wall mounted transformer 5 VDC 300 mA from transformer to ICI 1000PIM One 16 pin interface connector One RJ 14 modular data connector One transformer power connector Two eight position DIP switches Black plastic cover Indoor 32 to 120 F 0 to 49 C Unit Shipping 1 80 Ib 0 82 kg 301b 1 36 kg 0 75 Hx 4 94 W x 2 75 D 1 91 x 12 55 x 6 99 cm Design and specifications are subject to change without notice C1005M G 10 02 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on Pelco manufactured cameras CC3500 CC3600 CC3700 and MC3500 MC3600 Series two years on all other cameras Three years on Genex Series multiplexers server and keyboard Two years all standard motorized or fixed focal length lenses Two years on Legacy Camclosure Camera Systems CM6700 CM6800 CM8500 CM9500 CM9740 CM9760 Matrix DF5 and DF8 Series Fi
6. clude polling or non polling operation PIM addressing clock signal manipulation and ICI1000PIM graphics mode selection The following describes the DIP switch settings for bank 1 on the ICI1000PIM Refer to Figure 4 and Tables A and B NOTE If data is garbled or non existent and you have set the DIP switches correctly for your register try setting switch 1 on bank 1 to the opposite position of the standard setting that Pelco indicated owitch 1 This switch selects either the inverted or non inverted clock signal The switch setting varies depending on the register interface type selected for switch bank 2 from Table B switch 2 This switch selects either polling or non polling operation Non polling mode should be selected when using the ICI1000SE or ICI100051 Inter Check This mode is defined with a plus switch setting The DX2000 already is set for non polling even in PIM graphics mode switch 3 The function of this switch depends on the register interface type used In dot matrix cash register applications this switch selects either normal or PIM graphics mode Other applications have selections for monitor display of receipt or journal information This switch is normally in the closed position switches 4 8 These switches set the addresses of multiple PIMs in a party line system The address selected normally will coincide with the actual cash register number The switch settings that correspond to PIM addresses are list
7. ed in Table A CONFIGURING DIP SWITCH BANK 2 The switches in DIP switch bank 2 select the type of register interface the ICI1 000PIM interfaces Table B indicates the switch settings for specific register interfaces The first three switch settings have the same functions as switches 1 3 on DIP switch bank 1 Refer to the Configuring DIP Switch Bank 1 section for detailed descriptions of these three switches Refer to Figure 4 and Table B to set the switches in bank 2 31 oo oO 0 0 00 000 0 00 9 Ee REGISTER INTERFACE INPUT BANK 1 BANK 2 DATA POWER Figure 4 ICI1000PIM Switch Locations C1005M G 10 02 Table A PIM Address Settings for Switch Bank 1 OPEN FLIP THE SWITCH DOWN CLOSED FLIP THE SWITCH UP SWITCH 45678 POLLING PIM ADDRESS PIM 1 2 3 4 D 6 7 8 C1005M G 10 02 Table B Cash Register Interface Configurations OPEN FLIP THE SWITCH DOWN X POLLING NON POLLING R RECEIPT Normally CLOSED CLOSED FLIP THE SWITCH UP POLLING JOURNAL NON POLLING SELECT G GRAPHICS Normally CLOSED Register Interface Type Bank 1 Switch Bank 2 Switch 123 12345678 CASIO TK 2000 Dot Matrix Printer CASIO TK4300 Dot Matrix Printer CASIO TK1200 TK2600 TK4600 CE4115 CE4630 Dot Matrix Printer idee pu CASIO TK2100 CE4530 Dot Matrix Printer EET CASIO SA2000 2100 Serial Printer
8. he Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state REVISION HISTORY Manual Date Comments C1005M Original version C1005M A 8 93 Minor revisions to manual C1005M B 9 93 Addendum changes to manual 9 94 Changed manual to new format and minor revisions If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appr
9. lands Wokingham United Kingdom Montreal Canada
10. ll mount transformer into power This will power up the PIM SLIT JACKET TO EXPOSE WIRES Upon PIM power up you should see a prompt that matches your register CUT RED AND interface type displayed on the monitor A PIM version number will also be GREEN WIRES displayed If this prompt appears on the monitor the Inter Check and the PIM are communicating properly Figure 1 Cable Modification TO INTER CHECK UNIT STRAIGHT THROUGH PHONE CABLE WHITE BLUE BLACK YELLOW RED GREEN LII USER SUPPLIED CABLE 18 AWG SHIELDED WIRE IS SUGGESTED T E Row ICI1000PIM creer aa wHITE BLUE BLACK YELLOW RED GREEN Figure 2 Configuration for Wiring ICI1000PIM Module C1005M G 10 02 INSTALLATION FOR DX2000 DVR AND DX2000DH DATA HUB Refer to Figure 3 and the DX2000 Digital Video Recorder Installation Operation Manual C690M and DX2000DH Data Hub Manual C698M as you install the ICI1000PIM 1 2 C1005M G 10 02 Configure DIP switch bank 1 refer to the Configuring DIP Switch Bank 1 section for the device to which you are interfacing Configure DIP switch bank 2 refer to the Configuring DIP Switch Bank 2 section for the device to which you are interfacing Locate the 16 pin connector on your register interface Plug the register interface connector into the PIM Plug the provided RJ 14 six pin phone cable into the data connector in the PIM NOTE The provided RJ 14 phone
11. opriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico Intermediate Consignee Ultimate Consignee American Overseas Air Freight Pelco 320 Beach Road 3500 Pelco Way Burlingame CA 94010 Clovis CA 93612 5699 USA USA Changed manual to new format Revised the installation and operation instructions and added configuration settings for Epson Squirrel Micros 2700 NCR C1005M C 9 95 Minor revisons to manual C1005M D 1 96 Minor revisons to manual C1005M E 8 98 register with RS 485 printers Ruby Verifone and standard parallel printer C1005M F 8 02 Changed manual to new format Revised the manual to add DX2000 DVR material Replaced Figure 3 with a different drawing C1005M G 10 02 Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco C1005M G 10 02 Expanded instructions for executing a PIM DEFAULT LOAD DL Included statement that the DX2000 is set for non polling Copyright 2002 Pelco All rights reserved PELCO World Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1309001 Orangeburg New York Las Vegas Nevada Eindhoven The Nether
12. r odds Continued on next page C1005M G 10 02 Table B Cash Register Interface Configurations Continued Register Interface Type Bank 1 Switch Bank 2 Switch 123 12345678 PANASONIC JS 6500 Dot Matrix Printer XG 4 RCALLEN RC204 Drum Printer X RUBY VERIFONE RS 232 Standard Serial Printer SAMSUNG 4900 4915 4940 Dot Matrix Printer Version 3 or 4 SANYO ECR 580 690 720 EPSON 220F Dot Matrix Printer SHARP A430 DP630 Dot Matrix Printer SHARP 2381 2391 Drum Printer SHARP 3230 3231 3240 3241 4230 4231 Dot Matrix Printer SHARP 3100 3100S 3110 3250 3252 3300 3310 3311 Dot Matrix Printer SHARP 4230 4231 Dot Matrix Printer SHARP 2595 Drum Printer SHARP 2385 2386 2395 2396 Drum Printer SHARP A550 Dot Matrix Printer SHARP 3220 Dot Matrix Printer SHARP 2540 2590 2590S Drum Printer standard Parallel Printer SWEDA 2810 0MRON RS14 30 USA Type Drum Printer SWEDA 2810 0MRON RS14 40 USA Type Drum Printer SWEDA 2810 0MRON RS14 40 European Type Drum Printer SWEDA 2820 0MRON XXXX XX USA Type Drum Printer SWEDA 2860 TEC 136 141 191 196 DISPLAY TEC 206 216 227 230 290 DISPLAY TEC 141 Printer Drum Printer TEC 132 145 Drum Printer TEC 2200 2300 2600 DPR 610 620 Dot Matrix Printer TEC 2200 2300 2600 DPR 630 Dot Matrix Printer TEC 2200 2300 2600 DPR 61A Dot Matrix Printer TEC 1050 1060 1100 1190 DPR 710 Dot Matrix Printer TEC 1050 1060 1100 1190 DPR 730 Dot Matrix Printer TEC 1400 1600 1700 190
13. xed Dome products Two years on Spectra Esprit and P520 Scanners including when used in continuous motion applications Two years on WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applica tions that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides t
Download Pdf Manuals
Related Search