Pelco DVR DX4500 User's Manual
Contents
1. HDD 1 Connects to the SATA 1 connecto HDD 2 Connects to the SATA 2 connecto Mounting Basket A HDD 3 Connects to the SATA 3 connector supported for DX4600 only HDD 4 Connects to the SATA 4 connector supported for DX4600 only O00000 Mounting Basket B 6 C2676M 9 07 New hard disk drive found A Press OK to format hard disk drive s Please contact your dealer for service sd ee Figure 2 New Hard Disk Drive Found Dialog Box PARTS LIST AND TOOLS Oty a a Description Hard disk drive Serial ATA cable for connecting the HDD to the motherboard ESD disposable wrist strap and anti static mat Mounting screws for securing the HDD to the mounting basket Installation manual To install the HDD you will also need a nonmagnetic Phillips screwdriver 1 and an optional small container to store screws not supplied C2676M 9 07 Installing a Hard Disk Drive 1 Properly shut down the DX4500 DX4600 Series DVR Refer to the installation manual or operation programming manual supplied with the unit 2 Unplug the power cord from the wall socket A WARNING It is critical that the unit be unplugged for your safety You must remove the power cord because current continues to flow through the DX4500 DX4600 even when the unit is without power First unplug the power cord from the wall socket then unplug it from the rear of the DVR Figure 3 Removing Power Cord from Wall 3 Remov2. Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C2676M 9 07 Original version Pelco the Pelco logo Camclosure Esprit ExSite Genex Legacy and Spectra are registered trademarks of Pelco Copyright 2007 Pelco Endura and Spectra Ill are trademarks of Pelco All rights reserved DLP is a registered trademark of Texas Instruments Inc PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1 09001 Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore South Africa Spain Sweden United Arab Emirates United Kingdom United States
3. PA 3 10 Only use replacement parts recommended by Pelco 11 The unit must be properly shut down and turned off to install the system and video data drive WARNING It is critical that the DX4500 DX4600 be unplugged for your safety You must remove the power cord because current continues to flow through the DX4500 DX4600 even when the unit is off First unplug the power cord from the wall socket then unplug it from the rear of the DVR 12 Make sure you protect the unit and its components from electrostatic discharge ESD The product and or manual may bear the following marks constituting a risk of electric shock is present within CAUTION This symbol indicates that dangerous voltage this unit RISK OF ELECTRIC SHOCK This symbol indicates that there are important DO NOT OPEN operating and maintenance instructions in the literature accompanying this unit ATTENTION WARNING This product is sensitive to Electrostatic Discharge ESD To avoid ESD A damage to this product use ESD safe practices during installation Before touching Aud adjusting or handling this product correctly attach an ESD wrist strap to your wrist and suavo appropriately discharge your body and tools For more information about ESD control and senstmvenevices Safe handling practices of electronics please refer to ANSI ESD S20 20 1999 or contact the Electrostatic Discharge Association www esda org C2676M 9 07 5 Introduc
4. 7 Reassembling the Unit 1 Replace the chassis cover using the screws you removed from the sides and rear of the unit refer to Figure 14 Figure 14 Replacing the Chassis Cover 2 Attach the silver product label that came with your upgrade kit to the inside of your DVR s front door a Remove the paper backing from the product label b Carefully place the label adhesive side down on a free section of the inside of the door c Press down firmly to ensure that the label properly adheres to the inside of the door NOTE In the event that your unit or its components require service specific labels must be present and appropriately affixed to the unit s door Pelco product support personnel use these labels to identify the exact components installed in your system A separate product label is required for each upgrade component installed on the DX4500 DX4600 3 Reinstall the unit in a rack enclosure if necessary and reconnect all of the cables and peripheral equipment you removed earlier 4 This completes the reassembly of the DX4500 DX4600 5 To complete the HDD installation refer to Formatting on page 16 C2676M 9 07 15 Formatting The DX4500 DX4600 automatically detects when a new drive is installed or when a current drive is switched to a different SATA connector After the DX4500 DX4600 starts the system prompts you to format the newly installed drive Drives that have not been switched to a different SATA connec
5. P displays The lamp and color wheel will be covered for a period of 90 days The air filter is not covered under warranty e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video oducts e One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months e Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s iability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products hall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential jamages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise T
6. PELLO DX4500 DX4600 Series Hard Disk Drive Installation Instructions DEN Digital Video Recorder C2676M 9 07 C2676M 9 07 Contents important Safety InstrtictlonS in as cai sv a A ae aN NN sade eagtens goede nee des T RN 5 INTRODUCTION se sh pte ses eee OES ee Wika aes be eee ad hele Moen SA r EA Ari fe Sab ede 6 Before You Rein usos bokbindare ay RAR AGA LE Aaa ON ASA D EAD Dad tals dina ddan boa Rene 6 Parts List and 100I 2 2 c cashaetaelveie e a a e a tenders be 7 Installing a Hard Disk Drive ss sx nc de K evi 9 R deh day ees saato iapa KRE es ven kus 8 Opening the Chassis renner ase dur al sd T A Edet or aa er nde wae hE ee hay aay die bd 9 Slot Assignments and Component Layout 00 0 c cece cece tence eee ee 11 Removing the Mounting Basket 0 000 c cece cece cence aaaea 12 Removing the HDD a seeded b rs R K 2 K aves widened RRR iach w AR R des 13 Inserting the HDDs oa tona HT e aN tame a lot enero N ound ean ea atlas amp 13 Reinstalling the Mounting Basket 00 002 c cece cece eee rr rer rer ere eee 14 Reassembling the Unites 6 25 2 R 9052 R 0 8 boden bd R A boat ooh eee E ooh bk RZ SD oy 15 Formatting acs he asec whereas ee duw hl STEGAR Mee Malye Me dare SSG SN ANE ees 16 C2676M 9 07 3 List of Illustrations GO d O GQ E won l a C J r el a GO GQ E GK A C9 LO Installation Order of HDDs sens a New Hard Disk Drive Found Dialog Box Removin
7. e the power cord from the back of the unit TH T n e PIR II T eN MIN HT Figure 4 Removing Power Cord from Back of Unit 4 Disconnect any cables or connections that may restrict access or interfere with the removal of the unit NOTE The security surveillance service provided by the DX4500 DX4600 is interrupted when the unit is taken offline 5 If applicable Unscrew the fasteners that are securing the unit in the rack and carefully lift it out of the rack AN WARNING The chassis assembly includes parts with sharp edges To avoid injury use caution when working in and around the chassis and components C2676M 9 07 OPENING THE CHASSIS If the DX4500 DX4600 is mounted in a rack it must be removed from the rack prior to HDD installation One person can lift and remove the DVR Make sure the unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the chassis cover 1 Ensure that the DVR and all of its components are protected against ESD Before handling any electronic components you should take steps to ground yourself properly so that any built up static electric charges are dissipated away from the unit a Cover all work areas with approved anti static mats supplied b Attach the disposable wrist strap supplied Refer to Figure 5 and the included Safe Handling of Hard Drives instructions C2668M for proper ESD procedures c Attach t
8. g Power Cord from Wall Removing Power Cord from Back of Unit Disposable Wrist Strap ra Removing the Chassis Cover Interior Slot Assignments and Components Removing the Data and Power Cables Remov Remov ing the Mounting Basket ng the HDD from Mounting Basket Reattaching HDD to Mounting Basket Replaci ng the Mounting Basket Reconnecting the Data and Power Cables Replac ng the Chassis Cover Application Window and GUI Toolbar Hard D isk Drive Recovery in Progress Dialog Box C2676M 9 07 Important Safety Instructions Be sure to read familiarize manual and all safety instructions and before proceeding with the HDD installation Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Do not block any ventilation openings Install in accordance with the manufacturer s instructions Only use attachments accessories specified by the manufacturer CAUTION These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so stallation should be done only by qualified personnel and conform to all local codes Fan fe 0 EH w 0
9. he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state 0 state a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco 2 RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 2096 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way
10. he copper end of the wrist strap to an upainted surface of any grounded appliance An appliance is considered grounded if it can direct ESD to the earth usually through its power cable An appliance that is plugged into an electrical outlet is considered grounded a unit is not considered grounded when it is unplugged WARNINGS Do not touch the circuit board with your hand or a tool Hold the HDD by the sides only e Do not wear grounding straps over clothing as clothing generates static electricity COPPER END Figure 5 Disposable Wrist Strap 2 Move the DX4500 DX4600 to an area that will provide full access to its internal components C2676M 9 07 9 2 Using a Phillips screwdriver remove the chassis cover and do the following a Remove the top two screws on the left and right side panels of the DVR b Remove the four silver screws on the top of the unit fastening the cover to the back of the unit c Carefully remove the chassis cover by sliding it back and up Set aside the cover Figure 6 Removing the Chassis Cover C2676M 9 07 SLOT ASSIGNMENTS AND COMPONENT LAYOUT Refer to Figure 7 for information about the DX4500 DX4600 s layout of major components Figure 7 Layout of Major Components System Board SATA 1 4 Connectors CD DVD System Board Cable Mounting Basket holds SATA drive 1 and 2 Mounting Basket holds SATA drive 3 and 4 for DX4608 DX4616 CD DVD Drive Location mounting brac
11. ket supports one CD or DVD drive Chassis Exhaust Fan 00000000 Power Supply C2676M 9 07 11 REMOVING THE MOUNTING BASKET If a HDD is already installed go to step 1 If a HDD is not yet installed go to step 2 1 To remove the SATA HDD power connector and data cable do the following a Grasp the top and bottom of the SATA power connector and carefully and simultaneously pull straight back on the connector Refer to Figure 8 b Grasp each side of the SATA data connector and carefully and simultaneously pull straight back on the connector Refer to Figure 8 Figure 8 Removing the Data and Power Cables 2 To remove the HDD mounting basket do the following a Using a Phillips screwdriver unscrew the four screws that attach the mounting basket to the chassis Refer to Figure 9 b Gently lift the basket up and out with the drive s attached Be careful not to force the basket free or to disturb other components inside the unit Refer to Figure 9 Figure 9 Removing the Mounting Basket C2676M 9 07 REMOVING THE HDD NOTE It is recommended that you do not remove previously installed drives If you do remove a drive for any reason be sure to note the arrangement of the drives within the drive basket and reinstall them in the same order they appeared prior to removal It is critical that drives be returned to the DX4500 DX4600 in their original order 1 To remove the HDD if applicable from the basket do the fol
12. lowing a Using a Phillips screwdriver unscrew the screws that attach the drive to the basket b Pull the drive out of the basket Figure 10 Removing the HDD from Mounting Basket INSERTING THE HDD 1 To insert the HDD in the basket do the following a Position the drive in the basket b Using a Phillips screwdriver reinstall the screws to attach the drive to the basket C If necessary Repeat steps a and b to insert another HDD Figure 11 Reattaching HDD to Mounting Basket C2676M 9 07 13 REINSTALLING THE MOUNTING BASKET 1 To reinstall the HDD mounting basket a Gently lower the basket into place Be careful not to force the basket free or to disturb other components inside the unit b Using a Phillips screwdriver fasten the four screws that attach the drive basket to the chassis O Figure 12 Replacing the Mounting Basket 2 To reconnect the SATA data and power cables do the following a Grasp each side of the SATA data connector and carefully and evenly push the connector on to the drive data connector Ensure that the plug is pushed all the way on the drive data connector b Grasp the top and bottom of SATA power connector and carefully and evenly push the connector on to the drive power connector Ensure that the connector is pushed all the way on the power connector 3 Repeat step 3 for each HDD being installed Figure 13 Reconnecting the Data and Power Cables C2676M 9 0
13. tion Welcome to the hard disk drive HDD installation instructions for the DX4500 DX4600 Series digital video recorder DVR Before you install the hard drive familiarize yourself with all the instructions in this manual The DX4508 DX4516 supports two HDDs and a storage capacity up to 1500 GB The DX4608 DX4616 supports four HDDs and a storage capacity up to 3000 GB There are three optional hard drive kits DX4546HDD250KIT 250 GB DX4546HDD500KIT 500 GB and DX4546HDD750K IT 750 GB BEFORE YOU BEGIN Some DX4500 DX4600 DVRs are shipped without HDDs installed To record video you must first install at least one HDD Before you begin verify whether your unit was shipped with our without a HDD If your unit was shipped with a HDD installed and data is stored on one or more of the HDDs you must ensure that the drives are reinstalled in the same position and connected to their original SATA connectors NOTE Hard disk drives are installed in a specific order at the factory refer to Figure 1 When removing a HDD be sure to label the drive to ensure that it is reinstalled in the same location If the HDD is reinstalled in a different location when the unit is restarted the New hard disk drive found dialog box opens prompting you to format the HDD refer to Figure 2 If you select OK you will reformat the HDD erasing all stored data To avoid reformatting the HDD click Cancel Figure 1 Installation Order of HDDs
14. tor are not reformatted J WARNING Before initiating a format procedure verify that the drives are reinstalled in the same position and reconnected to their orginal SATA connectors For information refer to Before You Begin on page 6 and the DX4500 DX4600 server operation programming manual C2674M 1 On the front panel or remote control press and hold the Power button until your hear a beep and then release the button After a few seconds the DX4500 DX4600 startup screen appears 2 Wait until the DVR displays the HDD configuration has been changed dialog box in the application window HDD configuration has been changed Press OK to reconfigure hard disk drive s Please contact your dealer for service 3 Figure 15 Application Window and GUI Toolbar 16 C2676M 9 07 2 Do one of the following To format the newly installed HDDs click OK The Hard disk drive recovery in progress dialog box appears To cancel the formatting process click Cancel The unit exits to the application window Hard disk drive recovery in progress Figure 16 Hard Disk Drive Recovery in Progress Dialog Box 4 Wait until the Hard disk drive recovery complete dialog box appears 5 Click OK The application window appears C2676M 9 07 Green gt lt The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002 95 EC This eq
15. uipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002 96 EC of the European Union regarding the disposal of waste electrical and electronic equipment WEEE Contact your local dealer for procedures for recycling this equipment C2676M 9 07 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below e Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products e Three years on Spectra IV products e Three years on Genex Series products multiplexers server and keyboard e Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty e Three years on PMCL200 300 400 Series LCD monitors e Two years on standard motorized or fixed focal length lenses e Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products e Two years on Spectra III Esprit ExSite and PS20 scanners including when used in continuous motion applications e Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Two years except lamp and color wheel on Digital Light Processing DL
Download Pdf Manuals
Related Search