Pelco DX8000-UPDVD User's Manual
Contents
1. gt Figure 2 Removing Power Cord from Unit C1604M 6 04 5 Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge ESD Before handling any electronic components you should take steps to ground yourself properly so that any built up static electric charges are dissipated away from the unit The most effective method for combating ESD is to use a properly grounded wrist strap B NOTE If you do not have access to a grounded wrist strap you can discharge any built up static by periodically touching an unpainted section of the chassis Figure 3 ESD Protection C1604M 6 04 Prepare Unitfor Drive Installation OPEN THE UNIT CHASSIS C1604M 6 04 WARNING The chassis assembly includes parts with sharp edges To avoid injury use caution when working in and around the DX8000 s chassis and components If the DX8000 is mounted in a rack remove it and transport it to an area that will provide full access to the unit chassis a Disconnect any cables or connections that might restrict access to or the removal of the unit b Unscrew the fasteners that are securing the unit in the rack c Carefully lift the unit out of the rack NOTE Removing the DX8000 from a rack may require more than one person Refer to the DX8000 Installation Manual for rack mounting information Place the DX8000 on a flat surface with ample workspace 3 Using a Phillips head screwdriver rem2. Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Spectra Genex Legacy Coaxitron Esprit and Camclosure are registered trademarks of Pelco Spectra Il and Spectra Ill are trademarks of Pelco Copyright 2004 Pelco All rights reserved PELCO Worldwide Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com IS09001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East Pelco and the Pelco logo are registered trademarks of Pelco Copyright 2004 Pelco All rights reserved Windows is a registered trademark of Microsoft Corporation C1604M 6 04
3. Interior 8 C1604M 6 04 Remove the Existing Optical Drive DISCONNECT THE CD DVD DATA CABLE AND POWER WIRES When removing data cable and power wires pull the connectors straight out Do not rock connectors back and forth or remove a connector by pulling it by its wires or cable 1 Remove the IDE data cable from the existing CD DVD by carefully pulling the plastic cable tab away from the rear of the drive Refer to Figure 7 Figure 7 Removing the IDE Data Cable C1604M 6 04 2 Remove the power connector from the CD DVD drive Refer to Figure 8 M Sq d lt a 4 f Figure 8 Removing the CD DVD Power Connector C1604M 6 04 REMOVE THE CD DVD DRIVE 1 Using a Phillips head screwdriver unfasten the two screws that attach the CD DVD to the chassis Refer to Figure 9 Figure 9 Removing CD DVD Mounting Screws C1604M 6 04 2 Gently pull the CD DVD drive out of the DVR through the front of the unit Refer to Figure 10 Figure 10 Removing the Existing Optical Drive C1604M 6 04 Install the New DVD RW Drive into the Unit 1 Insert the new DVD RW into the DVR a Make sure the drive is oriented correctly b Insert the new DVD RW into the DVR through the front of the unit Refer to Figure 11 DVD RW Figure 11 Inserting the New DVD RW Drive C1604M 6 04 13 C Using a Phillips head screwdriver and the two screws provided in the upgrade kit secure the drive to the u
4. months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s iability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state fa warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information Model and serial number 2 Date of shipment P O number Sales Or
5. PELLI DX8000 UPDVD Upgrade Installation Manual BAGUE Digital Video Recorder C1604M 6 04 PELLO Protecting people and property in a million locations worldwide Introduction The following instructions serve as an installation guide for the DX8000 UPDVD drive kit PARTS LIST B NOTE This upgrade kit includes a Pelco certified DVD RW drive Using any other drive voids the manufacturer s warranty for the DX8000 Oty Description 1 DVD RW drive 2 Mounting screws TOOLS NEEDED 1 Phillips head screwdriver 1 nonmagnetic 1 Properly grounded ESD wrist strap and mat 4 Small containers for storing screws optional C1604M 6 04 1 Getting Ready 1 Familiarize yourself with the instructions throughout this manual 2 Check that you have all the necessary parts and tools Refer to the Parts List and Tools Needed section 3 Shut down the DX8000 Series DVR unit Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shutting down your unit 4 Unplug the power cord from the wall socket and then from the rear of the DVR WARNING For safety reasons you must remove the power cord because current continues to flow through the DX8000 even when the unit is off Remove the power cord from the wall socket first and then from the rear of the DVR It is critical that the unit be unplugged for your safety Figure 1 Removing Power Cord from Wall 2 C1604M 6 04 We
6. der number or Pelco invoice number 3 Details of the defect or problem there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA
7. nit s chassis Refer to Figure 12 Tighten the screws securely but do not over tighten Figure 12 Securing the New DVD RW Drive C1604M 6 04 RECONNECT THE DATA CABLE AND POWER WIRES IMPORTANT Data and power connectors fit together only one way All connectors are keyed to ensure that they are inserted in the proper orientation Examine the drive motherboard and cable connectors before installation so that connectors are properly aligned Make sure connectors are seated in the mating connectors securely but do not force the connection When installing drive power cables push the connectors straight in or out do not rock connectors back and forth 1 Connect the DVD RW power cable according to the diagram in Figure 13 4 SS a gt SS Figure 13 Installing the DVD RW Power Connector C1604M 6 04 15 2 Connect the DVD RW drive to the system motherboard using the existing data cable Refer to Figure 14 Pp A ye VU Po A N 4 SN P Figure 14 Installing DVD RW Data Cable C1604M 6 04 Reassemble the Unit 1 Using a Phillips head screwdriver reattach the side panel you removed earlier Refer to Figure 15 Figure 15 Replacing Side Panel C1604M 6 04 2 Replace the chassis cover using the same screws you removed from the side and rear of the unit Refer to Figure 16 Figure 16 Replacing Chassis Cover C1604M 6 04 C1604M 6 04 Reinstall the unit in a rack enclo
8. ove the chassis cover WARNING Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover Refer to the Getting Ready section a Remove the two top most screws on the left and right side panels of the DX8000 Refer to Figure 4 b Remove the four silver screws fastening the cover to the rear of the unit These screws are the ones closest to the top of the unit Refer to Figure 4 c Carefully remove the chassis cover by sliding it back and up Set aside the cover Figure 6 illustrates the interior of the DX8000 Figure 4 Removing Chassis Cover C1604M 6 04 4 Using a Phillips head screwdriver remove the side panel from the side of the unit closest to the CD DVD drive a Remove the four screws from the side panel Refer to Figure 5 b Set the panel and screws aside for use later Figure 5 Removing Side Panel C1604M 6 04 COMPONENT LAYOUT Figure 6 shows the location of your DX8000 Series DVR s major components Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity POWER SUPPLY DIMM SOCKETS RAM r1 D RW c I if CPU i HARD DRIVE REAR 0F DVR l l i FRONT OF DVR VGA CARD k HIHI PCISLOT1 2 3 4 E 5 6 REAR CROSS BRACE FRONT CROSS BRACE MOTHERBOARD MOTHERBOARD IDE CONNECTORS IDE CONNECTORS SECONDARY PRIMARY Figure 6 DX8000
9. sure if necessary and reconnect all cables and peripheral equipment that you removed earlier Plug the power cord back into the power supply and then into the wall Turn on the power switch and allow the unit to start up and find the new DVD RW This may take several minutes ON OFF Figure 17 Restarting Unit Notes 20 C1604M 6 04 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on the following fixed camera models CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X Three years on all other fixed camera models including Camclosure Integrated Camera Systems and Genex Series multiplexers server and keyboard Two years on all standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM8500 CM9500 CM9700 Series Matrix DF5 and DF8 Series Fixed Dome products Two years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications Two years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders and NVR300 network video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six
Download Pdf Manuals
Related Search