Peavey 1012 Sub User's Manual
Contents
1. 5 dB SPL re 20 Figure 5 7 1012 amp 1012 Sub 1012 only 500 Frequency Hz Figure 6 150 ik 2 Sk 10k 20k Frequency Hz Impulse 1012 Subwoofer Top Mounting Dimensions 174 20 X 3 4 FULL THREAD INSERT 5 127 0 5 000 201 08 7 916 74 08 MM 2 916 2 V V V 50 8 MM 34 95 2 000 1 375 69 85 MM 2 750 IN Impulse 1012 Subwoofer Bottom Mounting Dimensions 1 4 20 X 3 4 FULL THREAD INSERT 5 127 0 MM 5 000 IN 231 24 9 104 IN 104 24 4 104 y FEM 34 93 MM 1 375 50 8 MM 2 000 IN 69 85 2 750 Features and SPECNICANONS subject to change without notice Peavey Electronics Corporation 711 A Street Meridian MS 39301 601 483 5365 FAX 486 1278 www peavey com 2000 Printed in the U S A 9 002. C T RO impulse 1012 Sub Add On Weather Resistant Injection Molded Subwoofer Speaker System SPECIFICATIONS Enclosure Peavey Impulse 1012 Subwoofer Frequency Response Filtered 52 Hz to 150 Hz Unfiltered 52 Hz to 3 5 kHz Low Frequency Limit 3 dB point 52 Hz Useable Low Frequency Limit 10 dB point 44 Hz Power Handling Filtered 2 000W peak 1 000W program Unfiltered 2 000W peak 1 000W program Sound Pressure Level 2 83V 1M swept sine input in anechoic environment Filtered 97 dB Unfiltered 101 dB midrange level Maximum Sound Pressure Level Filltered 124 dB continuous Unfiltered 131 dB continuous Transducer Complement Model 1208 4 SPS 12 Black Widow woofer Box Tuning Frequency Fbox 54 Hz Crossover Type Passive Internal Low Pass Electroacoustic Crossover Frequency Filtered 150 Hz Crossover Slope 12 dB octave 2nd order low pass Impedance Nominal 4 ohms Impedance Minimum 3 4 ohms Input Connections Filtered 1 4 phone jack and 4 pin Speakon connector in parallel Unfiltered 4 pin Switching Neutrik Speakon Enclosure Materials and Finish Injection molded high impact polypropylene of a nominal thickness of 1 4 with textured finish Mounting Provisions Stand mounting via molded in mount flying via Versamount 70 top
3. ed and 52 Hz to 3 5 kHz unfiltered POWER HANDLING There are many different approaches to power handling ratings Peavey rates this speaker system s power handling using a modified form of the AES Standard 2 1984 Utilizing audio band 20 Hz to 20 kHz pink noise with peaks over four times the RMS level this strenuous test signal assures the user that every portion of this system can withstand today s high technology music The test signal contains large amounts of very low frequency energy effectively sim ulating the frequency content of live music situations The full measure of high fre quencies in the test signal allow for expo sure of the speaker to synthesized tones that may extend beyond audibility This rating is contingent on having minimum 3 dB of amplifier headroom available ARCHITECTURAL AND ENGINEER ING SPECIFICATIONS The loudspeaker system shall have a frequency response from 52 Hz to 150 Hz through the filtered inputs and from 52 Hz to 3 5 kHz through the unfiltered input The nominal impedance shall be 4 ohms The maximum filtered program power shall be 1000 watts and a peak power of 2000 watts The maximum program power through the unfiltered input shall be 1000 watts and a peak power of 2000 watts with a minimum amplifier headroom of 3 dB The peak SPL with inaudible dis tortion shall reach 124 dB through the fil tered input and128 dB through the unfil tered input with music as a source when mea
4. ne exposure to sunlight and rain by tilting speaker down and a splash shield on top WARNING Before attempting to suspend this speaker consult a certified structural engineer Speaker can fall from improper suspension resulting in serious injury and property damage Do not sus pend or mount any product or device from this enclosure Use only Grade 5 hardware or better All associated rigging is the responsibility of others THREE TWO LIMITED WARRANTY NOTE For details refer to the warranty statement Copies of this statement may be obtained by contacting Peavey Electronics Corporation P O Box 2898 Meridian Mississippi 39302 2898 Neutrik amp Speakor are a registered trademark of Neutrik AG Impulse 1012 Subwoofer Amplitude Response IW 1m On Axis 100 200 500 2k Frequency Hz Impedance Figure 2 100 200 500 Ik 2k Frequency Hz dB SPL 20 Figure 3 dB SPL re 20 Impulse 1012 Subwoofer Harmonic Distortion 1 FON ops de ok ap ka i Frequency Hz Harmonic PORE Rated PONE Frequency Hz 2nd Harmonic 3rd Harmonic Figure 4 Impulse 1012 and Impulse 1012 Subwoofer Subwoofer used in add on mode TENON 5
5. or bottom of cabinet and four rubber feet for floor use Dimensions H x W x D 23 11 16 60 17 cm x 17 13 16 45 24 cm in front 10 24 5 cm in rear x 13 3 4 34 92 cm Net Weight 40 lbs Shipping Weight 46 Ibs Specifications for Impulse 1012 and Impulse 1012 Subwoofer system subwoofer used in add on via filtered input Frequency Response 50 Hz to 18 kHz Low Frequency Limit 3 dB point 50 Hz Useable Low Frequency Limit 10 dB point 43 Hz Power Handling system at 3 2 ohms 1000 W program 2000 W peak Impedance Nominal 3 2 ohms Impedance Minimum 2 7 ohms FEATURES 1000W program power input Hypervent plus direct radiator design Add on subwoofer with easy hookup or crossed over sub 12 weather resistant Black Widow woofer Filtered input biamp input Built in carry handles Mounting points top and bottom Built in stand mount DESCRIPTION The Impulse 1012 Subwoofer was designed to complement the Impulse 1012 full range speaker To utilize the sub woofer simply run the normal full range signal to the Impulse 1012 run a 1 4 phone jack terminated cable or a 4 pin Neutrik Speakon terminated cable out from the second jack on the Impulse 1012 full range speaker system over to the Impulse 1012 Subwoofer then jack into the filtered input on the subwoofer The system with the Impulse 1012 full range system and Impulse 1012 S
6. sured at a distance of 1m and driven to full output capacity The system shall utilize a 12 Black Widow 1208 4 SPS woofer An electrical low pass filter with a resultant corner frequency of 150 Hz shall be included with input connections to the filter provided via a 1 4 phone jack in par allel with a 4 pin Neutrok Speakon con nector both labeled Filtered and a sepa rate 4 pin switching Neutrik Speakon bypasses the filter to go directly to the woofer and is labeled Unfiltered The enclosure shall be constructed of injection molded polypropylene of 1 4 nominal thickness and shall have a UL flame rating and reinforced internal ribs A handgrip shall be molded in on each side of the woofer and on the top rear edge A vinyl coated perforated metal grille shall be provided for woofer protection The cabinet shall incorporate four rubber feet for floor standing use and five mounting point inserts on the top and bottom each for flying use The outside dimensions shall be 23 11 16 60 17 cm tall by 17 13 16 45 24 cm wide in front 10 24 5 cm in rear by 13 3 4 34 92 cm deep and the weight shall be 40 lbs The loudspeaker system shall be called a Peavey model Impulse 1012 Subwoofer WARNING When use of a stand is considered the Peavey S 1 stand is recom mended Other stands may not have a base sufficiently wide enough for stability and safety CAUTION For permanent installation avoid direct co
7. ubwoofer is now a 3 2 ohm composite system with a power handling of 1000 watts Bass response has been extended to 50 Hz and the tonal balance of the com posite system has been flattened out for a full range dynamic system For biamplification use with an electron ic crossover use the unfiltered 4 pin switching Neutrik Speakon input jack This input is also useful for utilizing the Impulse 1012 Subwoofer as a compact high output drum monitor The Impulse 1012 Subwoofer is equipped with a Peavey Hypervent This unique innovation reduces the pipe organ reso nance of the vent tube allowing the vent to seem longer in one dimension than it phys ically is By terminating the open end of the vent acoustically acoustic attenuation standing waves are reduced and the hollow sound of a ordinary vent is avoided Avoiding typical vent sounds the sub woofer is harder to localize and placement is less critical The Peavey Impulse 1012 Subwoofer has a new high power 12 model 1208 4 SPS Black Widow woofer in it providing high power low bass response in a compact system package FREQUENCY RESPONSE This measurement is useful in deter mining how accurately a given enclosure reproduces an input signal The frequency response of the Impulse 1012 Sub is measured at 1 meter using a 2 82 volt swept sine input The selected drivers in the Impulse 1012 Sub gives a smooth frequency response from 52 Hz to 150 Hz filter
Download Pdf Manuals
Related Search