Patton electronic Model 1058 User's Manual
Contents
1. Follow the steps below to connect the Model 1058 VDSL Interfaces Note The Model 1058 units work in pairs One of the units must be a Model 1058 CO Central Office and the other unit must be a Model 1058 CP Customer Premise It does not matter which end is the 1058 CO and which is the 1058 CP The link is always initiated by the 1058 CP As long as the 1058 CO is powered on the 1058 CP can establish a link by being powered on or by hav ing its power reset 1 To function properly the two Model 1058 s must be connected together using twisted pair unconditioned dry metal wire between 19 0 9mm and 26 AWG 0 4mm Leased circuits that run through signal equalization equipment are not acceptable 2 The Model 1058 is equipped with two interface jacks that can be used on the VDSL interface an RJ 45 or a terminal block These VDSL interfaces are a two wire interface Observe the signal pin relation ships on the Model 1058 s VDSL interface jacks The RJ 45 connector on the Model 1058 s twisted pair interface is polar ity insensitive and is wired for a two wire interface The signal pin rela tionship is shown in Figure 3 1 no connection 2 no connection 3 no connection 4 2 Wire RING 5 6 2 Wire TIP 2 3 4 5 6 7 no connection no connection 8 RII 8 no connection Figure 3 Model 1058 RJ 45 twisted pair line interface The terminal block connector on the Model2. ISO yid An ISO 9001 Certified Company Part 07M1058 A Doc 058091UA Revised 10 12 01 USER MANUAL MODEL 1058 VDSL Modem S VDSLLink power Ethernet POTS SDN 7 Bo PE PATTON Ei Zlecironics To SALES OFFICE 301 975 1000 TECHNICAL SUPPORT 301 975 1007 1 0 1 1 1 2 1 8 2 0 2 1 2 2 3 0 3 1 3 2 3 3 3 4 4 0 4 1 4 2 A 1 A 2 A 3 A 4 A 5 A 6 A 7 A 8 A 9 A 10 A 11 C 1 C 2 C 3 Warranty Information eeeeeeeeeeereeeee eene 3 Radio and TV Interference sssssssssssssseeeee 3 e zn vie M 4 SeIVICe iuge EH ERR DH E TE 4 General Information eeeeeeeeeeesseeeeeeene ennt nnne 5 Features tnx cite ri eh cota Sete i en le robs ot eee 5 Description eec Sere ree it E CORE 5 Installation eee eene reise 7 Connecting the Twisted Pair Line Interface 7 Connecting the 10 100Base T Ethernet Interface 9 Connecting the 10 100Base T Ethernet Port to a Hub 9 Connecting the 10 100Base T Ethernet Port to a PC DTE 10 Connecting the POTS ISDN line eene 10 Connecting Power sssessseeseeeneeeneeeneen nennen 11 o Jc m 12 Power Up ziii te feo e IUD UOI PR MES 12 Front Panel LED Status Monitors ccssccceeeseeeeeteeees
3. No configuration is necessary for the power supply See Appendix B for domestic and international power supply and cord options DC power supplied via the power supply jack to the 1058 must meet the following requirements DC power supplied must be regulated 5VDC 5 1 0A minimum Center pin is 5V The barrel type plug has a 2 5 5 5 10mm I D O D Shaft Length dimensions The Model 1058 does not have a power switch so it powers up as soon as it is plugged in 11 4 0 OPERATION Once the Model 1058s are properly installed they should operate trans parently No user settings required This section describes reading the LED status monitors 4 1 POWER UP Before applying power to the Model 1058 please review section 3 4 Connecting Power on page 11 to verify that the unit is connected to the appropriate power source 4 2 FRONT PANEL LED STATUS MONITORS The Model 1058 features five front panel LEDs that monitor power the Ethernet signals and the VDSL Connection Figure 9 shows the front panel location of each LED Table 1 on page 13 describes the LED func tions Ethernet Activity LED Ethernet Link LED VDSL Error LED VDSL Link LED Figure 9 Front panel standalone Model 1058 12 Table 1 Front panel LED description LED Description Power Solid GREEN to indicate the unit is powered on VDSL Link Active Green Solid green ON to indicate that the end to end VDSL link between the
4. Model 1058s is established The VDSL LED is OFF when the link is down VDSL Error Active Red Flashes Red to indicate errors have occurred on the VDSL link Ethernet Link Active Green Solid Green indicates that 10 100Base T Ethernet link has been established Ethernet Activity Active Yellow Flashes yellow to indicate Ethernet activity on the Model 1058 s 10 100Base T Ethernet port 13 APPENDIX A SPECIFICATIONS A 1 LAN CONNECTION Shielded RJ 45 10 100Base T IEEE 802 3 Ethernet VDSL Connection RJ 45 and Terminal Block A 2 TRANSMISSION LINE Two wire unconditioned twisted pair A 3 VDSL LINE RATE 12 5 Mbps symmetric upstream downstream A 4 ACTUAL DATA RATE 10 Mbps symmetric upstream downstream A 5 VDSL DISTANCE 4 000 ft 1 219 m A 6 VDSL SURGE SUPPRESSOR Gas tube with maximum current surge 20 kA 8120 us A 7 LED STATUS INDICATORS Power Green VDSL Link Green amp Error Red Ethernet Link Green amp Activity Yellow A 8 POWER SUPPLY External AC and DC options AC 120 VAC 220 VAC and UI 120 240 VAC e DC 12 VDC 24 VDC and 48 VDC A 9 TEMPERATURE RANGE 0 50 C A 10 HUMIDITY Up to 90 non condensing A 11 DIMENSIONS 1 58H x 4 16W x 3 75D in 10 6H x 4 1W x 8 8D cm 14 APPENDIX B MODEL 1058 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model Base Models Description 08055 120 5 1 1058D CO CO V
5. or does not performs as warranted your sole recourse shall be repair or replacement as described above Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics spe cifically disclaims all other warranties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user 1 1 RADIO AND TV INTERFERENCE The Model 1058 generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufac turer s instructions may cause interference to radio and television recep tion The Model 1058 has been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Sub part B of Part 15 of FCC rules which are designed to provide reasonable protection from such interference in a commercial installation However there is no guarantee that interference will not occur in a particular instal lation If the Model 1058 does cause interference to radio or television reception which can be determined by disconnecting the unit the user is encouraged to try to correct the interference by one or more of the fol lowing measures moving the computing equip
6. 1058 s twisted pair interface is polarity insensitive and is wired for a two wire interface The signal pin relationships is shown in Figure 4 m7 OQ o RING TIP Figure 4 Model 1058D Terminal Block twisted pair line interface 3 2 CONNECTING THE 10 100BASE T ETHERNET INTERFACE The shielded RJ 45 port labeled Ethernet is the 10 100Base T interface This port is designed to connect directly to a 10 100Base T network Figure 5 shows the signal pin relationships on this interface You may connect this port to another Ethernet device via a Type 4 or Type 5 cable that is up to 328 ft long 1 TX data output from 1058 1 p sdi 2 TX data output from 1058 HP Scd 3 RX data input to 1058 3 p 4 4 no connection 5 5 no connection 6 6 RX data input to 1058 8 le 7 no connection 8 no connection Figure 5 Model 1058 10 100Base T RJ 45 Connector Pinout Connecting the 10 100Base T Ethernet Port to a Hub The Model 1058 10 100Base T interface is configured as DTE Data Ter minal Equipment just like a 10 100Base T network interface card in a PC Therefore it expects to connect to a 10 100Base T Hub using a straight through RJ 45 cable Figure 6 diagrams the cable wiring for con necting the Model 1058 to a 10 100Base T hub 1058 10 100Base T Port 10 100Base T Hub RJ 45 Pin No RJ 45 Pin No di 1 RX
7. DSL Modem data only no power supply 1058D CP CP VDSL Modem data only no power supply 1058D 2PK VDSL MODEM Kit includes one central office CO and one customer premise CP Model 1058 data only no power supply 1058DV CO CO VDSL Modem voice amp data no power supply 1058DV CP CP VDSL Modem voice amp data no power supply 1058DV 2PK VDSL MODEM Kit includes one central office CO and one customer premise CP Model 1058 voice amp data no power supply 07M1058 User Manual Power Supplies 08055DCUI 100 240VAC 5V reg DC 2A Universal Input Adapter 120 VAC 5V reg DC 1A Input Adapter 12V PSM 12 VDC Input Adapter 24V PSM 24 VDC Input Adapter 48V PSM 48 VDC Input Adapter 0805US American Power Cord 0805EUR European Power Cord CEE 7 0805UK United Kingdom Power Cord 0805AUS Australian Power Cord 0805DEN Denmark Power Cord 0805FR France Belgium Power Cord 0805IN India Power Cord 0805IS Israel Power Cord 0805JAP Japan Power Cord O805SW Switzerland Power Cord Only required with optional UI power supply 08055DCUI 15 APPENDIX C MODEL 1058 SERIES INTERFACE PIN ASSIGNMENT C 1 10 100BASE T INTERFACE RJ 45 e Pin 1 TX e Pin 2 TX Pin 3 RX Pin 6 RX Pins 4 5 7 8 no connection C 2 VDSL INTERFACE RJ 45 Pin 4 RING Pin 5 TIP Pins 1 2 3 6 7 8 no connection Terminal Block See Figure 4 on page 9 C 3 POTS ISDN INTERFAC
8. DTX eee 2 RX Oe ee 3 TX eee aaa aaa 6 TX Figure 6 Wiring diagram for connecting the Model 1058 to a 10 100Base T hub Connecting the 10 100Base T Ethernet Port to a PC DTE The Model 1058 10 100Base T interface is configured as DTE Data Ter minal Equipment If you wish to connect the 1058 to another DTE devices such as 10 100Base T network interface card in a PC or 1058s in a back to back arrangement you must construct a 10 100Base T crossover cable as shown in Figure 7 1058 10 100Base T Port 10 100Base T DTE RJ 45 Pin No RJ 45 Pin No 1 TX 1 TX 2 TX 2 TX 3 RX 3 RX 6 RX 6 RX Figure 7 10 100Base T crossover cable 3 3 CONNECTING THE POTS ISDN LINE The RJ 45 port labeled POTS ISDN is the POTS ISDN interface A tele phone or an ISDN device may be connected to this port and carried over the VDSL line The units do not need power for the POTS interface to 10 work The RJ 45 connector in the model 1058 s POTS ISDN interface is wired as shown in Figure 8 EP s 1 no connection 2 no connection 3 no connection ee 4 2 wire RING 5 2 wire TIP 6 T4 1 2 3 4 5 6 7 no connection 8 RR pell no connection 8 no connection Figure 8 Model 1058DV RJ 45 POTS ISDN interface 3 4 CONNECTING POWER An external AC or DC power supply is available separately This connec tion is made via the barrel jack on the rear panel of the Model 1058
9. E RJ 45 Pin 4 2 wire RING Pin 5 2 wire TIP Pins 1 2 3 6 7 8 no connection Copyright 2001 Patton Electronics Company All Rights Reserved 16 17
10. Mbps at 4 000 ft i Wie 1 219 m 24 AWG 0 5 mm Remote as network Total distance up to 4 652 ft 1 418 m Figure 1 Typical application The 1058DV CO and 1058DV CP work together to create a transparent extension between two peered Ethernet LANs POTS ISDN calls can be made over the VDSL link without interfering with the data Figure 1 shows a typical point to point application 3 0 INSTALLATION Because the Model 1058 requires no configuration it can be installed and made operational quickly Installation takes place as follows 1 Connecting the line interface between the units refer to section 3 1 Connecting the Twisted Pair Line Interface on page 7 Note See Figure 2 for the rear panel arrangements 2 Connecing the Ethernet interface refer to section 3 2 Connecting the 10 100Base T Ethernet Interface on page 9 3 Connecting the power plug refer to section 3 4 Connecting Power on page 11 1058DV VDSL twisted pair Ethernet RJ 45 interface POTS ISDN port twisted pair terminal block VDSL twisted pair interface terminal block interface Figure 2 Model 1058 standalone rear panel 3 1 CONNECTING THE TWISTED PAIR LINE INTERFACE The Model 1058 supports communication between two peer Ethernet LAN sites over a distance of up to 4 652 ft 1 418 m over 24 AWG 0 5 mm twisted pair wire Note Actual distance and link performance may vary depending on the environment and type guage of wire used
11. S Easy to install standalone VDSL modems no configuration required Auto sensing full or half duplex Ethernet Auto sensing 10 100Base T Extends network connections up to 4 652 ft 1 418 m over 2 wire 24 AWG unconditioned lines 12 5 Mbps symmetric line rate 10 Mbps data rate POTS ISDN splitter on board Transparent operation LED indicators for Power Ethernet Link amp Activity VDSL Link amp Error Surge supression up to 20 kA 8120 us Available in rack mount or standalone configurations Made in the USA 2 2 DESCRIPTION The Patton Electronics Model 1058 CO and 1058 CP VDSL modems provide high speed LAN connections between peered Ethernet LANs remote PC s or any other network enabled 10 100Base T device Operating in pairs with a Model 1058 CO central office located at one end of the LAN extension and a Model 1058 CP customer premise at the other end these units can automatically forward LAN broadcasts multi casts and frames across a 2 wire twisted pair link The data is passed transparently that is unmodified through the 1058s What s more the 1058s automatically add and delete MAC addresses only passing packets across the VDSL link that are meant for the remote peered LAN Only Models 1058DV CO and 1058DV CP have POTS ISDN split ters on board 10 1008ose T 10 100Base T oy Model 1058DV CO led p o Twisted Poir 2 wire A Su pe l a 12 5
12. eeeeeenes 12 Specifications ecrit err ecelterartei nire 14 LAN Gonriectiohi certet ib p e e e eed 14 Transmission Line sssssssssssssee eene 14 VDSIz Gin Rates aide ee ttn t ere ent ied e 14 Actual Data Rate ui eee eus 14 VDSL DiStanGe oe Duce aT eon en ea pr eere 14 VDSL Surge Suppressor ssssssseeemee 14 LED Status InidiGaterss ise heh totom tag 14 POWER Supply 4c ee o pce te Rer wee SS 14 T mperat re4RangG titer citet rg t rtt e vi d im ats 14 Flurnielty ue esce iere oem ap delved eeeaiaten aisha toy 14 DIMENSIONS tuvniind PER 14 Model 1058 Series Factory Replacement Parts and Accessories 15 Model 1058 Series Interface Pin Assignment 16 10 100BaS6 T InterfaGe 53 ert ea ee p be EROR 16 LM P 16 VDSL Interface ctr t tete mr t pre tenete 16 RJE a e 16 Terminal BIoCKk renerne a 16 POTS ISDNCInterfaees ri me t mea 16 RJ 45 cie itasse cages eerte dtes rg tat e er etui dte depen 16 1 0 WARRANTY INFORMATION Patton Electronics warrants all Model 1058 components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of the shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If this product fails
13. ment away from the receiver re orienting the receiving antenna and or plugging the receiving equipment into a different AC outlet such that the computing equipment and receiver are on different branches 1 2 CE NOTICE The CE symbol on your Patton Electronics equipment indicates that it is in compliance with the Electromagnetic Compatibility EMC directive and the Low Voltage Directive LVD of the European Union EU A Cer tificate of Compliance is available by contacting Technical Support This device is not intended to be connected to the public telephone network Caution Note The Model 1058DV is currently awaiting Part 68 approval 1 3 SERVICE All warranty and nonwarranty repairs must be returned freight prepaid and insured to Patton Electronics All returns must have a Return Materi als Authorization number on the outside of the shipping container This number may be obtained from Patton Electronics Technical Services at Tel 1 301 975 1007 Email supportG patton com URL http www patton com Note Packages received without an RMA number will not be accepted 2 0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product This product has been thoroughly inspected and tested and is warranted for one year for parts and labor If any questions or problems arise during installation or use of this product contact Patton Electronics Technical Support at 1 301 975 1007 2 1 FEATURE
Download Pdf Manuals
Related Search