Paslode IM250A User's Manual
Contents
1. Battery does not appear to accept charge Inoperative indicator lights on charger or Try battery in tool after a full charge cycle when battery is plugged into the charger defective charger If tools indicator light is red charger not working properly Replace charger or monitor charging time to ensure battery has adequate time for recharging It is normal for battery to feel warm after properly charging Battery damaged or cycle life exhausted Replace battery Charger gets hot makes excessively loud Damaged charger Discontinue use immediately and unplug noise or smokes during charging cycle from power source Replace charger and Charger cord or wall plug gets hot tag or dispose of charger to prevent accidental re use or connection to power source Normal Stage of Operation SYMPTOM POSSIBLE PROBLEMS SERVICE Fan does not run tool indicator light is Battery is not charged Charge battery blinking red or solid red l Clean battery terminals with soft cloth Battery terminals are oily dirty or corroded Fan does not run or runs slower than Battery is discharged Charge battery normal tool indicator light is solid red Work contacting element does not depress Work contacting element is bent or build up of Remove and inspect lower probe Clean track fully tool does not operate debris in track restricts operation Repair or replace lower probe as required Lockout feature is engaged Add strip of nails Repl2. hold in the upright position and simply place the metering stem against a solid object and gently push about three or four times A small amount of fuel should be released each time Wear safety glasses when performing this test Never perform this test near an open flame or sparks while smoking or where the fuel may get into your eyes If fuel is not released with each operation of the metering valve this indicates that there is no more fuel left in the cylinder and it must be replaced Dispose of the empty fuel cell properly see page 16 Clearing a Jam An occasional problem you may encounter is a jammed fastener Because of the unique design of the Paslode Angled Finish Nailer clearing a jammed fastener is easy 1 Remove the battery 2 Pull the latch releasing front guide Pivot front guide forward 3 Clear jam and push driver blade back up to its normal position 4 Close front guide andlatch it Check that work contacting element moves freely Servicing Air Filter Open the cover by pressing slightly above the adapter and pivoting the cover open The air filter simply lifts out Tap the filter GENTLY to remove any dust Check and clean the air filter every two days Soap and water restores the filter to a like new condition FILTER End of Workday Routine These simple steps are based on maintaining the safety and operational efficiency of the Paslode Angled Finish Nailer Before yo
3. AGAINST THE WORK SURFACE Fan motor starts fuel is injected into combustion Turn chamber and adiustment mixed with air by nah in the fan either direction SQUEEZE TRIGGER Spark plug ignites the fuel air mixture driving the piston assembly down on Depth of Drive Adjustment the fastener Remove the battery before adjusting the depth of drive The depth of drive adjustment is done by turning the RELEASE adjustment wheel as shown by the arrows on the side of the TRIGGER tool LIFT TOOL Combustion chamber opens Fan exhausts hot gases and cools internal components A DANGER NOTE Altitude Restriction The work contacting element and nose will become hot Impulse tools are powered by an internal combustion after prolonged or rapid use If it becomes necessary to engine and are effected by altitude The tool may adjust the work contacting element avoid touching with lose power or become erratic at elevations of 4000 bare hands feet or greater When using the tool at elevations of 4000 9000 ft it is recommended that the high altitude fuel metering valve 219247 be used This tool must be operated in a well ventilated environment because the tool exhausts carbon monoxide similar to a chainsaw or lawn mower Exposure to carbon monoxide may cause dizziness nausea or unconsciousness Fasteners and Applications Applications The Pa
4. LOAD FASTENERS WITH THE TRIGGER AND OR WORK CONTACTING ELEMENT PRESSED IN A fastener may be accidentally discharged Safety Instructions NEVER OPERATE THE TOOL WITH THE WORK CONTACTING ELEMENT REMOVED OR DISABLED This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating until it is completely against the work surface NEVER operate the tool if the work contacting element is not working properly ALWAYS POINT THE TOOL AWAY FROM YOURSELF AND OTHERS WHEN CLEARING JAMS OR REMOVING FASTENERS Pull the follower slightly back and push the release lever Tip the tool nose up slightly and fasteners should slide out of the rear of the magazine If fasteners are jammed refer to the appropriate servicing section of this manual NEVER OPERATE THE PASLODE ANGLED FINISH NAILER IF PARTS ARE LOOSE DAMAGED OR MISSING DO NOT DRIVE FASTENERS INTO KNOTS OR ON TOP OF OTHER FASTENERS A fastener may ricochet and cause serious injury 11 OPERATE THE TOOL ONLY ON THE WORKPIECE The Paslode Angled Finish Nailer should be operated only when itis in contact with the work surface When fastening thin materials such as plywood be sure to position the tool so that the fastener is driven into the underlying piece Safety Instructions 12 NEVER DRIVE FASTENERS INTO AREAS WITH 15 PROPERLY STORE FUEL CELL CONCEALED HAZARDS Always check the area behind the work su
5. correct on the work site The following field service procedures are the only service procedures you should attempt Anything else that may appear wrong with the Paslode Angled Finish Nailer should only be diagnosed and repaired by a fully trained service technician If you have any reason to believe that your problem is beyond the service procedures in this manual contact your Paslode representative immediately Never attempt any maintenance of a Impulse tool without first removing the fuel cell and battery Maintenance should be started only after the tool is completely inoperative Battery Check Periodically check on the battery indicator light the light in the handle of the Paslode Angled Finish Nailer When encountering a problem the first step should always be to make sure the battery has enough charge to operate the tool When the work contacting element is depressed on work piece the fan motor will turn on and the blinking green indicator light will turn solid green If the indicator light blinks red or glows red recharge the battery Servicing Fuel Cell Check If the Paslode Angled Finish Nailer s fan operates and the indicator light is green but the tool will not cycle or does not drive fasteners completely check the fuel cell With the fuel cell out of the tool check to see if the cell still contains fuel and that the metering valve is working To determine if there is any fuel left in the fuel cell
6. replacement part or accessory provided in accordance with this warranty will carry a warranty for the balance of the period of warranty applicable to the part it replaces This warranty does not apply to part replacement required due to normal wear This warranty is void on any tool which has been subjected to misuse abuse accidental or intentional damage use with fasteners fuel batteries or battery chargers not meeting Paslode specification size or quantity improperly maintained repaired with other than genuine Paslode replacement parts damaged in transit or handling or which in Paslode s opinion has been altered or repaired in a way that affects or detracts from the performance of the tool PASLODE MAKES NO WARRANTY EXPRESSED OR IMPLIED RELATING TO MERCHANTABILITY FITNESS OR OTHERWISE EXCEPT AS STATED ABOVE and Paslode s liability AS STATED ABOVE AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of or in connection with the use and performance of the tool except to the extent other wise provided by applicable law PASLODE SHALL IN NO EVENT BELIABLE FOR ANY DIRECT INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO DAMAGES WHICH MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR PRODUCTION SPOILAGE OF MATERIALS INCREASED COST OF OPERATION OR OTHERWISE An Overview of the Paslode Angled Finish Nailer Description The Paslode Angled Finish nailer is a self contained fully portable n
7. used with tool 2 5 Copyright 2002 Illinois Tool Works Inc
8. wall mount unit s plug into plug receptacle on the back of the charger see picture A green light indicates power is on and charger circuit is ready 2 Remove the battery from tool or case and insert terminals down into charger The red light will come on indicating that the battery is charging and the green light will go out If battery is completely discharged the red light and the green light may alternate back and forth for up to 20 minutes This safety feature slowly recharges the battery until it is ready to accept the full charging current If the red and green lights continue to alternate after 20 minutes replace the battery 3 After charging is complete the red light will go out and the green light will come on indicating that the battery is fully charged The charger will keep the battery at full charge until it is removed 4 Unplug the wall mount unit from the charger and remove the wall mount unit from the 120V AC outlet CHARGING TIMES First charge new battery Discharged Battery 2 hours 5 minutes to 2 hours CHARGING DON TS 1 Do not charge battery outdoors or in temperatures below 40 F 5 C 2 Do not allow metal objects to come in contact with battery terminals 3 Do not puncture or attempt to open battery case or cells 4 Do not store battery where it will be subjected to temperatures above 120 F 49 C 5 Do not incinerate battery 6 Do not use a defective battery charger o
9. P Model IM250A as 0 e Part No 900600 Angled Finish Nailer CORDLESS OPERATING MANUAL IMPORTANT DO NOT DESTROY It is the customer s responsibility to have all operators and service personnel read and understand this manual Printed in U S A 2002 Illinois Tool Works Inc 405630 9 www paslode com 03 02 Contents Subject Page Introduction and Warranty cccccccssseeeeeeeeeeeeeeeeeeeeeees 2 An Overview of the Paslode Angled Finish Nailer Safety Instructions yecostsscrsneeiaceztcanteaaeesaucradeasenescesensetasascles 4 Battery and Charge sosrmesenneinae ia ia 7 Fuel Cell and Metering Valve ccccccccceeseeeeeeeeeaeeees 9 Preparing the Paslode Angled Finish Nailer for Use 12 Paslode Angled Finish Nailer Operation 00 13 Fasteners and Applications cccccccsseceeseeeeeeeeeeeees 14 NC UNG asters cores seers oa een EA oe E E EE 15 Troubleshooting cccccccseseececceeeeeeeceseeecssaseeeessaaeeess 17 The Impulse battery charger system meets all safety requirements for power tools J Paslode s re CORDLESS An Ilinois Tool Works Company 888 Forest Edge Drive Vernon Hills Illinois 60061 www paslode com g Paslode p ye Nailers are made in the U S A and are CORDLESS protected by one or more of the following U S patents 4 403 722 4 483 280 4 483 474 4 522 162 Other patents issued and pending Paslode
10. ace fuel cell Tool will not cycle fan runs indicator light Fuel Cell empty is solid green Spark wire out of spark plug Remove cap and check spark lead insert in spark plug and replace cover Spark plug is dirty Clean tool cylinder head No spark is generated Return tool to authorized Paslode dealer for service 17 Troubleshooting Normal Stage of Operation Tool operates properly but fasteners do not Work contacting element requires adjustment Adjust work contacting element drive fully Fuel cell is low Check fuel cell and replace as required There may be loss of seal in combustion Press work contacting element against chamber workpiece for one minute Pull trigger If fastener does not drive there is a leak that requires service Tool operates properly but fasteners are Work contacting element is not adjusted Adjust work contacting element Readjust sometimes over driven and sometimes properly for the type of material being as required when material density or under driven fastened thickness of material being fastened changes Tool operates but no fastener is driven Wrong fasteners being used Use only fasteners meeting Paslode specifications Check Fasteners and Applications section for fastener types and sizes recommended for use in Impulse tool Follower not properly engaged behind fastener Position follower behind fastener strip and strip engage strip Fuel cell is low Check f
11. ailer that uses liquid hydrocarbon fuel to power a unique linear drive internal combustion motor In order for you to fully understand the information contained in this manual you need a basic understanding of the Paslode Angled Finish nailer As you can see in the illustration below the Paslode Finish nailer is made up of three major areas handle motor and magazine As you examine the Paslode Angled Finish nailer become familiar with the three major areas and the various components located in each of them The Handle contains the fuel cell indicator light and the trigger The Motor contains the cover and filter the motor housing the nose and the work contacting element The Magazine contains the components to load and control the fastener and the battery for the Paslode Angled Finish nailer removable cover amp filter cap motor housing Motor quick clear cover adjustable depth of drive opposite side lockout feature no mar tip Specifications Dimensions Weight with battery 4 lbs 140z Height 11 1 2 inches Length 10 3 4 inches Magazine Angled use Paslode angled fasteners only Cycle Rate Intermittent Operation 2 to 3 nails per second Continuous Operation 500 nails per hour NOTE Exceeding these cycle rates could cause the tool to overheat resulting in loss of performance or damage to tool components By using the Paslode Angled Finish nailer at its recommended
12. cycle rate you will be able to drive several thousand nails in a typical workday Fasteners 16gauge angled F 16 Series Chisel Point Magazine Capacity 2 nail strips or 100 fasteners Battery 6 volts DC Provides enough energy to drive approximately 4000 fasteners on a full charge Fuel Cell Liquid hydrocarbon Provides enough fuel to drive approximately 1200 fasteners Z fuel cell compartment Handle soft grip reversable belt hook Magazine battery indicator light Opposite side nail count indicator battery compartment opposite side Safety Instructions The following safety instructions have been included in this booklet to provide you with basic information necessary for Ay WARNING safe operation of the Paslode Angled Finish Nailer DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS Do not expose the tool to temperatures in excess of 120 F 49 C Fuel and or the battery may burst releasing flammable gas The Paslode Angled Finish Nailer is an internal combustion device It produces hot exhaust flammable materials This A WARNING tool must not be used in a combustible environment or in the presence of combustible materials such as flammable chemicals adhesives gasoline or solvents This tool must be operated only in a well ventilated environment because the tool exhausts carbon monoxide
13. es or property damage Keep the fuel cell away from heat sparks and open flame Exposure to temperatures above 120 F 49 C may cause the fuel cell to burst releasing flammable gas Sunlight can raise the inside temperature of an unventilated car or van to above 140 F 60 C Do not puncture or attempt to open the fuel cell it is non refillable Do not incinerate reclaim or recycle the fuel cell Do notsmoke while installing or operating the metering valve Do not inhale the spray Keep out of the reach of children Store fuel cell s in well ventilated areas only Fuel Cell and Metering Valve There is a second container inside the fuel cell The inner container holds the fuel The space between the inner container andthe outer cylinder is filled with a gas called the propellant which is under pressure To eject the fuel propellant pressure squeezes the inner fuel container much as you squeeze a tube of toothpaste This squeezing action ensures that all the fuel is used and that the Paslode Finish nailer can operate in any position Because of this container within a container design you might hear the sound of fluid when shaking the fuel cell after all the fuel has been used This is the propellant which remains between the containers even after all the fuel has been expelled If you expose the empty fuel cell to extreme temperatures the propellant gas will expand and could cause the containe
14. is a member of C ISANTA VEY Introduction and Warranty Paslode Angled Finish Nailer Operating Manual This manual is intended to acquaint you with the Paslode Cordless Angled Finish Nailer Unlike other power fastening tools the Paslode Angled Finish Nailer is powered by an internal combustion linear motor In simpler terms your Paslode Angled Finish Nailer is powered by a motor similar to the one that powers an automobile The Paslode Angled The Paslode Finish nailer should be handled like other power fastening tools that you use Like most tools when used improperly injury could result If you are going to allow others to use the Paslode Finish nailer it is your responsibility to make sure that they also read and comply with the instructions in this manual before attempting to operate the tool Should you have questions about the Paslode Finish nailer or wish to obtain additional copies of this manual please contact your Paslode representative The space below is provided so that you may record your representative s name address and telephone number Finish Nailer ignites a fuel and air mixture to produce the energy to drive the motor which in turn drives the fastener The Paslode Angled Finish Nailer is totally self contained It carries its own fuel supply and battery along with a supply of fasteners For the nearest Paslode representative call 1 800 For ease of use this manual is divided into sec
15. l and Metering Valve Inserting Fuel Cell As you slide the metering valve fuel cell assembly into the Paslode Angled Finish Nailer you will notice a yellow Inserting the metering valve fuel cell assembly into the adapter at the top of the cylinder pocket As shown in the Paslode Angled Finish Nailer is very simple To begin press illustration this adapter is designed to ensure that the up at the bottom of the actuator cover and pivot outward to metering valve stem is properly aligned with the small hole open The cover will swing out of the way or orifice that leads to the combustion chamber Insert the metering valve stem into the orifice of the yellow colored gt 2 PULL OUT adapter Fuel Cell Metering Valve Stem Next with the metering valve stem pointed toward the front of the tool insert the metering valve fuel cell assembly Close the actuator cover to complete the loading of fuel in the Paslode Angled Finish Nailer Do this by swinging it up and over the fuel valve cylinder assembly and pushing down until the actuator cover snaps into position L 2 PUSH DOWN Fasteners The Paslode Angled Finish Nailer drives Paslode 16 gauge angled fasteners designed to be used with the tool The use of fasteners that do not meet Paslode standards could cause tool damage and will void all warranty claims Loading Fasteners STEP 1 Align the heads of the Paslode angled finish nails to the
16. ne that over heats and or smokes when plugged in 7 Do not immerse the battery in water Impulse Charging System Accessories Battery Charger Kit Part No 900200 Wall Mount Transformer Part No 900477 Battery Charger Base Part No 900476 Automotive Adapter Part No 900507 Cannot use with previous gray in color charging system components Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens This is the battery indicator light When you insert a fully charged battery into the tool you will see a blinking green light Ifthe indicator light blinks red recharge the battery Inserting Battery 1 Loadthe battery contacts first into the Paslode Angled Finish nailer 2 Push battery fully forward into its locked position 3 To remove battery push down on locking tab and slide battery out NOTE If battery is left in tool for an extended period the battery will discharge completely and will require recharging IMPORTANT Should your battery terminals become corroded and cause poor electrical contact clean the terminals using a soft cloth Clean the contacts Fuel Cell DANGER EXPLOSION FIRE HAZARD Read ALL _ safety instructions before using or handling the fuel cell Failure to follow ALL instructions may result in explosion or fire This may Cause severe personal injuri
17. not use straight fasteners Impulse Technology and Outdoor Weather Use the Paslode Angled Finish Nailer outdoors in dry weather when the nailer fuel cell and battery are between 20 F 7 C and 120 F 49 C HOT WEATHER OPERATION The Paslode Angled Finish Nailer requires cooling of the motor assembly to operate properly The fan normally provides the necessary air flow to permit continuous operation Whenever the Paslode Angled Finish Nailer is idle for extended periods keep the fuel and tool out of direct sunlight and in surroundings where temperatures will not exceed 120 F 49 C After extended periods of continuous use it may be necessary to cool the Impulse motor by setting tool aside for 10 15 minutes or until the tool operates normally An overheated tool may not drive nails completely or may operate erratically COLD WEATHER OPERATION Fuel cells at cold temperatures lose the required propellant pressure Bring the tool fuel cell and battery above 20 F 7 C by placing the tool ina heated building or vehicle Never expose the tool fuel cell or battery to flame The Paslode Angled Finish Nailer should not be used in the rain or where excessive moisture is present The use of the Paslode Angled Finish Nailer under these conditions may result in damage to tool components and cause the tool to malfunction Paslode Angled Finish Nailer Operation Operation PRESS WORK CONTACTING ELEMENT
18. ormation on Ni Cd battery recycling in your area Battery and Charging System The cordless tool comes with a rechargeable battery and its own charging system This charging system is the only one that will work with the Impulse batteries either round or oval The first step in preparing a new tool for operation is to fully charge the battery New batteries are shipped discharged and must be charged prior to first use Batteries will take 5 minutes to 2 hours time will be dependant on the amount of discharge of the battery to recharge Important Charging Notes CHEMICAL EXPLOSION HAZARD Read ALL instructions be fore charging or using bat tery Failure to follow ALL instructions may result in fire severe burns or re lease of toxic materials Battery Disposal The Impulse battery contains cadmium and must be recycled or disposed of properly It is illegal in some areas to place a nickel cadmium battery into the trash or solid waste stream You may contact your local recycling center for information on where to return the spent battery or call 1 800 822 8837 for information on Ni Cd battery recycling in your area REAR VIEW OF CHARGER BASE Plug Receptacle Charger Base THE PASLODE BATTERY CHARGING SYSTEM Battery and Charging System Charging Instructions 1 Remove wall mount unit with the orange label from the tool case and plug into a 120V AC outlet Set orange charger on a stable surface and insert
19. r to burst releasing flammable gases Metering Valve The metering valve contains a fuel metering system to inject the correct amount of fuel into the combustion chamber The metering valve with the yellow face is the only valve that will operate properly with the Paslode Angled Finish Nailer YELLOW FACE Do not attempt to reuse the metering valve Replace with fresh fuel cell valve and dispose of spent cell valve properly When replacing fuel cell also clean or replace the air filter for optimum tool operation NOTE Altitude Restriction Impulse tools are powered by an internal combustion engine and are effected by altitude The tool may lose power or become erratic at elevations of 4000 feet or greater When using the tool at elevations of 4000 9000 ft it is recommended that the high altitude fuel metering valve 219247 be used Fuel Cell and Metering Valve Attaching Metering Valve to Fuel Cell To attach the metering valve to a fuel cell 1 Press downward on the front side of the valve stem side until it seats 2 Press downward on the rear side of the valve until it seats 3 The valve is now completely seated onto the fuel can and can be inserted into the tool NOTE Impulse fuel cell are marked with an expiration date on the bottom of the can For maximum performance use fuel before expiration date Impulse Fuel is flammable Do not smoke when installing the metering valve 10 Fuel Cel
20. rface for A WARNING electrical wiring gas pipes water pipes sewer drains or other potential hazards Always store fuel cells where they will not be 13 ALWAYS MAINTAIN SECURE AND UNOBSTRUCTED exposed to an open FOOTING WHEN ON LADDERS PLATFORMS OR flame sparks or OTHER HIGH LOCATIONS temperatures above 120 F 49 C warnine Never over reach since 416 ALWAYS STORE THE TOOL WITH THE FUEL CELL tool recoil may cause a AND BATTERY REMOVED loss of balance Always be aware of edges and Store the fuel cell in the case with the Paslode Angled drop offs when nailing on Finish Nailer rooftops and other high locations Keep them in 17 KEEP THE TOOL CLEAN full view l A clean tool is less likely to jam or malfunction 18 KEEP YOUR HANDS CLEAR OF THE WORK AREA 14 ALLOW ONLY QUALIFIED PERSONNEL TO OPERATE SURFACE THE PASLODE ANGLED FINISH NAILER A amp warnine WARNING A fastener may exit at an Only persons who have angle unexpectedly and read and fully understand cause injury all tool operation safety and maintenance instructions should be allowed to operate the tool Battery Disposal The battery contains cadmium and must be recycled or disposed of properly It is illegal in some areas to place a nickel cadmium battery into the trash or solid waste stream You may contact your local recycling center for infor mation on where to return the spent battery or call 1 800 822 8837 for inf
21. silver brad channel in the rear of the magazine and insert one or two strips Push the nails strips forward STEP 2 Next while applying pressure to the release lever pull the follower toward the rear of the magazine until the follower passes the last strip of fasteners Release the lever on the follower and let the follower push the nails forward into the nose of the tool Loading fasteners i Z IS ae Pull Follower In the illustration above you will see an indicator arrow on the side of the follower When the indicator arrow is in the reload area marked on the side of the magazine you may insert a new strip of nails When the follower arrow reaches the lockout area the tool automatically locks the tool to prevent the tool from operating To unlock the tool simply reload another strip of fasteners Lockout Feature The purpose of this feature is to prevent needless blank cycling which could mar woods waste fuel and damage tool components Ten 10 nails will be left in the magazine when the follower reaches the lockout area When changing fastener length or loading at the beginning of the work day you should inspect the magazine and nose for any fasteners left in the tool These nails will not be visible unless you open the nose of the tool 12 Preparing the Paslode Angled Finish Nailer for Use Use only Paslode angled fasteners SE 2 l in DO
22. similar to a gas chainsaw or lawnmower Exposure to carbon monoxide may cause dizziness nausea or unconsciousness A WARNING Do not attempt to operate this tool until you have read and Aw warnine understood all safety ee precautions and manual instructions Failure to ALWAYS keep the follow all safety precautions and instructions may result in a permanent loss of vision Serious personal or even fatal injury property damage and or tool damage Paslode Angled Finish Nailer fuel cell battery and battery charger out of the reach of children Always wear EYE and EAR safety gear when working with or in the vicinity of the Paslode Angled Finish Nailer Eye protection must meet the requirements of ANSI Standard Z87 1 and should have side shields for increased protection NEVER ASSUME THE TOOL IS EMPTY Never point the tool at yourself or anyone else NEVER ENGAGE IN HORSEPLAY WITH THE TOOL The Paslode Angled Finish Nailer is not a toy itis a tool Careless and improper use may result in a serious accident NEVER CARRY THE TOOL WITH YOUR FINGER ON OR SQUEEZING THE TRIGGER This practice may result in the accidental discharge of a fastener NEVER OPERATE A MALFUNCTIONING TOOL Refer to the servicing or troubleshooting section of this manual to correct the problem If the problem cannot be corrected stop using the tool and report it to your supervisor or Paslode representative DO NOT
23. slode Angled Finish Nailer is suited for a variety of applications These include securing door and window casings attaching baseboards where walls meet floors attaching moldings where walls meet ceilings securing paneling securing chair rails picture molding and other decorative trim Head Crown A Casing Molding iTi Head Casing a 7 a e ee Chair i Rail Baseboard Molding ae Door Door Jamb Stop Base Shoe Fasteners j The Paslode Angled Finish Nailer drives Paslode 16 Gauge angled finish nails Fasteners are collated into strips of 50 for easy loading Paslode fasteners are designed to be used in Paslode tools use of other fasteners may cause damage to the tool or injury to the tool operator THE PASLODE FINISH NAILER DRIVES THESE NAILS PART NO LENGTH APPLICATION 650046 1 3 4 Baseboard Crown Chair 650047 Baseboard Casings Crown ee 14 Restrict Field Service to the Following _ CHECKING THE ENERGY LEVEL OF THE BATTERY _ RECHARGING THE BATTERY CHECKING THE FUEL CELL AND METERING VALVE _ REPLACING THE FUEL CELL _ CLEANING REPLACING THE AIR FILTER CLEARING A JAM CLEANING THE TOOL See cleaning manual Attempts to go beyond these procedures could result in serious personal injury or damage to the Paslode Angled Finish Nailer and voiding the warranty There are certain problems you may encounter when you are using the Paslode Angled Finish Nailer that you will be able to
24. tions see 682 3428 Contents Each section of the manual is written with you the tool operator in mind We have left out many of the technical terms so that you can easily understand how to get the maximum performance from your Paslode Angled Finish Nailer and how to avoid damaging the tool or injuring yourself But to accomplish this we need you to do two things Name Address 1 READ THE MANUAL FROM COVER TO COVER City State Zip BEFORE USING THE TOOL 2 FOLLOW ALL INSTRUCTIONS IN THE MANUAL Telephone Number Paslode Cordless Warranty and Limitations Paslode warranties that new Impulse power fastening tools parts and accessories will be free from defects in material and workmanship for the period shown below after the date of delivery to the original user ONE YEAR LIMITED WARRANTY A one year warranty will apply to all parts except those listed below as normal wearing parts or parts which are specifically covered by an extended warranty FIVE YEAR EXTENDED LIMITED WARRANTY A five year warranty will apply to all molded nylon parts e Cap and Grille e Handle Halves and Actuator e Trigger 90 DAY LIMITED WARRANTY A 90 day warranty applies to the following parts which are considered normal wear parts e Bumper e Driver Blades e O Rings WARRANTY STATEMENT Paslode s sole liability hereunder will be to replace any part or accessory which proves to be defective within the specific time period Any
25. u leave the work site 1 Remove battery and store in tool case Always use the Paslode Angled Finish Nailer case for transporting and storing the tool 2 Dispose of all empty fuel cells Remember to dispose of these cells where they will not be crushed punctured burned or found by children 16 When you get home 1 Place the battery in its charger if it needs charging as indicated by the red charge light on the handle 2 Wipe your Paslode Angled Finish Nailer with a clean soft cloth 3 Remove and clean the filter every two days 4 Checkworkcontacting elementto ensure it is operating freely Impulse Accessories A variety of accessories are available for the Paslode Angled Finish Nailer No Mar Replacement Tip Part No 900702 Battery Part No 404717 Extra battery allows use of one battery while spare battery is being charged Tinted Safety Glasses Part No 402512 Cuts glare while affording eye protection Clear Safety Glasses Part No 402510 Impulse Oil Part No 401482 Battery Charger Kit Part No 900200 Automotive Adapter Part No 900507 Impulse Angled Finish Nailer Case Part No 900713 Contact your Paslode representative for additional information Impulse Tools A 9 64 Hex Socket Wrench Part No 900736 is provided with each Paslode Angled Finish Nailer Troubleshooting Preparing Tool for Operation Battery Charger Problems SYMPTOM POSSIBLE PROBLEMS SERVICE
26. uel cell Spark plug wire is loose Check spark plug wire Air filter is dirty causing tool to overheat Remove air filter and clean Use soap and water to remove stubborn debris Tool is dirty Clean tool Built up dirt and debris on driver blade or in nose bore degreaser cleaner Tool is dirty Clean tool Clean track or replace work contacting Tool operates erratically or appears to be losing power tool indicator light is green Tool operated and drove fasteners but driver blade did not return to up position Clean driver blade and nose bore with Combustion chamber does not drop after Work contacting element is bent or is dirty tool cycles element If nailer will not operate after following the above service directions return the tool to an authorized Paslode representative for service For the nearest Paslode representative call 1 800 682 3428 For Technical support call 1 800 222 6990 7 Paslode An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills Illinois 60061 www paslode com Model Number PART NO IM250A 900600 PASLODE MODEL NUMBER DESIGNATION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it The following example illustrates the information contained in this tool model number IM 290 A Angled Finish Nailer 16ga IMPULSE Maximum fastener length Technology in inches that can be
Download Pdf Manuals
Related Search