Parkside A1 User's Manual
Contents
1. PARKSIDE SOLDERING GUN PLP 100 Al TL PARKSIDE SOLDERING GUN Operation and Safety Notes 6C pio ES GB CED Before reading unfold the page containing the illustrations and familiarise yourself with all functions of the device GB IE Operation and Safety Notes Page 5 7 PARKSIDE Table of contents Introduction desig rp ET Page 7 Description of parts and features Page 7 Included items 8 Technical data 8 Safety advice 1 Workplace safety Page 9 2 Electrical safety Page 9 3 Personal safety ccce or rere poseer Page 10 4 Careful handling and use of electrical power tools Page 12 Original accessories Page 12 Use SWitchinig Omand GH sitet coco ett ener itt Page 12 Replacingia soldering Page 13 Maintenance and Page 14 Service centre e hh Lee Page 14 Warranty eed innit Page 14 Disposal Page 16 Declaration of Conformity Manufacturer s Page 16 GB E 5 Introduction The following pictograms are used in these operating instructions on the device Read instruction manual Observe caution and safety notes Caution electric shock Danger to life Risk of explosion2. Maximum switched on duration 12 seconds 12 GB IE PARKSIDE Use Switching off o Release the ON OFF switch 4 Pause At least 48 seconds CAUTION Never heat up the device if it is not fitted with a sol dering tip o ATTENTION Never use in continuous operation mode The flow of electrical current controls the delivery of soldering heat As soon as the ON OFF switch 4 is released the delivery of soldering heat drops If the ON OFF switch 4 is pressed again the deliv ery of soldering heat rises Pay particular attention to achieving an even delivery of soldering heat to ensure the highest soldering quali ty You can do this by not allowing the soldering tip 1 to become excessively hot Note The device has a soldering light 3 to illuminate the work ing area Replacing a soldering tip CAUTION DANGER OF BURNS Allow the device to A cool down before replacing a soldering tip Release the two union nuts 2 using the open spanner 9 Pull the soldering tip 1 or 7 out of the holder Insert another tip into the holder Tighten the two union nuts 2 using the open spanner 9 VAN AEDS GB IE 13 Maintenance and cleaning Service centre Warranty Maintenance and cleaning VN EZANIN RISK OF INJURY Before you carry out any work on th
3. Risk of fire Warning Hot surfaces Volt AC Watts Effective power lt gt gt gt eo Wear a breathing dust mask protective glasses gloves and clothing Keep children away from electrical devices Check that the device mains lead and plug are in good condition Do not smoke Do not eat 291 219 6 GB IE Wi PARKSIDE Introduction Do not drink e Dispose packaging and appliance in an environmentally friendly way Soldering gun PLP 100 Al Introduction Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you understand how to handle it correctly Please read the operating instructions below Be careful to keep these advice notes and if necessary pass them on to a third party Proper use The device is intended for soldering tasks in a DIY environment Soft solder ing takes place at temperatures below 450 C Suitable solders have typical melting temperatures around 200 C Use the device only as described and for the indicated purposes The device is not intended for commercial use Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers The manufac turer will not accept liability for loss or damage arising from improper use Description of parts and features E
4. e device always pull the mains plug out of the mains socket and allow the device to cool a Clean the device after you have finished using it Use a cloth and a little mild detergent for cleaning the device In no circumstances use sharp objects or petrol solvents or clean ing agents that might attack plastic Do not allow any liquids to enter the inside of the device Service centre WN Have your device repaired only by qual ified specialist personnel using original manufacturer parts only This will ensure that your device remains safe to use PN EZAN If the plug or mains lead needs to be replaced always have the replacement carried out by the manufacturer or his service centre This will ensure that your device remains safe to use Warranty The warranty for this appliance is for 3 years from the date of purchase The appliance has been manufac tured with care and meticulously examined before de livery Please retain your receipt as proof of purchase In the event of a warranty claim please make contact by telephone with our Service Department Only in this way can a post free despatch for your goods be assured 14 GB IE VERDI Warranty The warranty covers only claims for material and maufacturing defects but not for transport damage for wearing parts or for damage to frag ile components e g buttons or batteries This product is for private use only and is not intended for commercial use The war
5. ion or in struction by a person responsible for their safety Children must never be allowed to play with the device Remain alert at all times watch what you are doing and always proceed with caution Do not use the device if you are tired or under the influence of drugs alcohol or medication One moment of carelessness when using the device can lead to serious injury 10 GB IE WA PARKSIDE Safety advice Never touch the hot soldering tip or the molten solder You could suffer burn injuries Always let the device cool before you replace components on the device clean it or check its condition m After use let the soldering gun cool down in air only Under no circumstances quench the tip in water When allowing the device to cool or when taking a break from using it always stand the device up vertically with the soldering tip at the top m Keep the device away from combustible materials A CAUTION DANGER OF INJURY Keep your hands away from the hot workpiece Avoid contact with the hot soldering tip Ifa dangerous situation arises pull the mains plug immediately out of the mains socket A CAUTION DANGER OF POISONING Do not breathe air contaminated with soldering fumes _ When working with the device for long periods do not allow fumes from soldering to build up They may be hazardous to health Always provide adequate ventilation of your working area In addition it is recommended that you wear pr
6. m Soldering tip 2 Union nut W PARKSIDE GB IE 7 Introduction Soldering light OFF switch Handle Mains lead Cutting tip Tin solder Open spanner 10 Solder flux 00 N Os Co Included items 1 Soldering gun PLP 100 A1 1 Carry case 2 Soldering tips 1 cutting tip 7 premounted 1 Open spanner 20g Tin solder 10g Solder flux 1 Operating instructions Technical data Rated voltage 230V Frequency 50 Hz Power 100 W Max soldering tip temperature 540 C Protection class ON max 12 sec OFF min 48 sec 8 GB IE PARKSIDE Safety advice AN Safety advice c CAUTION Failure to observe the instructions and advice given below may result in electric shock fire and or serious injury Workplace safety Keep your working area clean and well lit Untidy or poorly lit working areas can lead to accidents Do not work with the device in potentially explosive environments in which there are inflammable liquids gases or dusts Electrical power tools create sparks which can ignite dusts or fumes Keep children and other people away NS while you are operating the electrical tool Distractions can cause you to lose control of the device Electrical safety The mains plug on the device must match the mains sock et The plug must no
7. otective gloves a face mask and a protective apron BOG Do not eat drink or smoke in rooms where soldering is carried out Otherwise your hands may transfer any adhering traces of lead via food or cigarettes into your body Always wash your hands immediately after soldering Do not dispose of soldering waste with the household rubbish Soldering waste must disposed of as special waste WA PARKSIDE GB IE 11 Safety advice Use 4 a b Careful handling and use of electrical power tools When not in use always ensure that electrical power tools are kept out of reach of children Do not let any one use the device if he or she is not familiar with it or has not read the instructions and advice Electrical power tools are dangerous when they are used by inexperienced people Look after the device carefully Check for broken parts or parts that are damaged to the extent they detrimentally affect the functioning of the device Have any damaged parts repaired before you use the device Many accidents have their origins in poorly main tained electrical tools Original accessories attachments Use only the accessories detailed in the operating instructions The use of attachments or accessories other than those recommended here could lead to you suffering an injury Use Switching on and off Switching on a a Insert the mains plug into a suitable mains socket Press the ON CFF switch 4 and keep it pressed
8. pose of your worn out devices Declaration of Conformity Manufacturer C We Komperna GmbH the person responsible for documents Mr Felix Becker Burgstr 21 D 44867 Bochum Germany hereby de clare that this product complies with the following standards normative documents and EU directives EU Low Voltage Directive 2006 95 EC Electromagnetic Compatibility 2004 108 EC 16 GB IE 7 PARKSIDE Declaration of Conformity Manufacturer Applicable harmonized standards EN 55014 2 A1 2001 EN 55014 1 2006 EN 60335 2 45 A1 2008 EN 60335 1 A13 2008 EN 61000 3 2 2006 EN 61000 3 3 A2 2005 EN 62233 2008 Type Device description Soldering gun PLP 100 A1 Date of manufacture DOM 12 2010 Serial number IAN 61101 Bochum 31 12 2010 een Hans Komperna Managing Director We reserve the right to make technical modifications in the course of further development Wi PARKSIDE GB IE 17 IAN 61101 KOMPERNASS GMBH BurgstraBe 21 D 44867 Bochum by ORFGEN Marketing Last Information Update 12 2010 Ident No PLP100A1122010 6
9. ranty is void in the case of abusive and improper handling use of force and internal tampering not carried out by our authorized service branch Your statutory rights are not restricted in any way by this warranty The warranty period will not be extended by repairs made unter war ranty This applies also to replaced and repaired parts Any damage and defects extant on purchase must be reported immediately after un packing the appliance at the latest two days after the purchase date Repairs made after the expiration of the warranty period are subject to payment GB DES UK LTD Tel 0871 5000 700 0 10 minute e mail support uk kompernass com IE Kompernass Service Ireland Tel 1850 930 412 0 082 EUR Min Standard call rates apply Mobile operators may vary e mail support ie kompernass com Hl PARKSIDE GB IE 15 Disposal Declaration of Conformity Manufacturer Disposal The packaging is wholly composed of environmentally friendly materials that can be disposed of at a local recycling centre Sa Do not dispose of electrical devices with the household rubbish In accordance with European Directive 2002 96 EC covering waste electrical and electronic equipment and its transposition into national legislation worn out electrical devices must be collected sep arately and taken for environmentally compatible recycling Contact your local refuse disposal authority for more details of how to dis
10. t be modified in any way Do not use an adapter plug with devices fitted with a protec tive earth Unmodified plugs and matching sockets reduce the risk of electric shock Keep the device away from rain or moisture Water entering an electrical device increases the risk of electric shock Use a residual current device RCD for protection if operating the electrical power tool in a moist envi Hl PARKSIDE GB IE 9 Safety advice d ronment is unavoidable The use of an RCD reduces the risk of electric shock 4 Do not use the mains lead for any purpose for 52 which it was not intended e g to carry the device to hang up the device or to pull the mains plug out of the mains socket Keep the mains lead away from heat oil sharp edges or moving parts of the device Damaged or tangled mains leads increase the risk of electric shock Do not operate the device if the mains lead or mains plug is damaged VN damaged mains lead presents a serious danger to life from electric shock Always keep the mains lead out of the operating area and run it away from the rear of the device Always pull out the mains plug if you are about to leave the device unattended or wish to carry out any tasks on the device Personal safety Children or persons who lack the knowledge or ex perience to use the device or whose physical sensory or intellectual capacities are limited must never be allowed to use the device without supervis
Download Pdf Manuals
Related Search