Paradyne Application Module 9109 OCU-DP User's Manual
Contents
1. insert the OCU DP APM in the correct slot so that it mates with its matching I O card APMs are keyed so that they mate only with their matching I O cards 1 Remove the filler panel if applicable See the installation instructions that came with your housing for information 2 Remove the APM from the shipping box Handle only by the top and bottom edges to avoid damaging the card 3 At the front of the housing align the APM with the upper and lower tracks of the selected slot 5 Slot 2 Slot Front View 98 15152 02 4 Slide the APM into the tracks until it seats with the midplane connectors Be careful not to force the card or bend any pins 5 Close both the upper and lower ejector latches on the housing to lock in place then tighten the captive screws on the ejector latches Removing Replacing a Card Card removal procedures differ depending on whether you are removing the APM or I O card NOTE You can insert or remove the APM and its associated I O card without powering off the equipment and interrupting data flow through other cards in the network Removing Replacing an APM 1 Remove the housing s bezel if applicable See the installation instructions that came with your housing for information 2 Remove the captive screws from the ejector latches on the front of the housing 3 Press open the ejector latches to disengage the card from the midplane 4 Supporting the card by its edges pull str2. it for physical damage and tighten any screws that may have worked loose Contact your sales representative immediately if there are any signs of shipping damage or if anything is missing from your package Otherwise proceed with the installation Equipment You May Need to Order A DDS Network cable must be ordered for this product either the 14 ft Feature No 3600F3 501 or 25 ft Feature No 3600 F3 502 NOTE The following NAM I O versions are required to use the OCU DP APM The SINGLE T1 NAM for Model 9161 The DUAL T1 NAM for Model 9261 A HANDLING PRECAUTIONS FOR STATIC SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge ESD during normal operation When performing installation procedures however take proper static control precautions to prevent damage to equipment If you are not sure of the proper static control precautions contact your nearest sales or service representative 496 15149 Installing the I O Card The I O card provides the APM with DDS connections The I O card inserts directly behind the APM that it supports Slot numbers are identical to facilitate correct installation NOTE For the 2 port OCU DP APM only Port 1 and Port 2 on the I O card are functional 1 Remove the I O card from the shipping box Handle only by the top and bottom edges to avoid damaging the card 2 At the rear of the housing align the I O
3. PARADY NE 9109 OCU DP Application Module APM Installation Instructions Document Number 9109 A2 GN15 10 May 1999 Product Documentation on the World Wide Web We provide complete product documentation online This lets you search the documentation for specific topics and print only what you need reducing the waste of surplus printing It also helps us maintain competitive prices for our products Complete documentation for this product is available at www paradyne com Select Library gt Technical Manuals gt NextEDGE Multiservices Access System Select the following document 9191 A2 GH30 NextEDGE Multiservices Access System Technical Reference To request a paper copy of a Paradyne document Within the U S A call 1 800 PARADYNE 1 800 727 2396 Outside the U S A call 1 727 530 8623 Before You Begin Make sure you have 1 The housing and any associated hardware already installed J AT1 NAM already installed in Slot 01 and connected to the network LJ Applicable cables 1 A small Phillips screwdriver 1 or 2 to install the APM _J A small flat blade screwdriver to install the I O card and cable connections See the Technical Reference for additional information on Troubleshooting Technical Specifications Cables Connectors and Pin Assignments Package Checklist Verify that your package contains the following J OCU DP APM LI OCU DP I O card When your equipment arrives inspect
4. aight out until the card clears the housing 5 Refer to Steps 3 5 of Installing the APM on page 6 If the slot Then the Was previously unassigned Configuration settings are the factory defaults and are accessible from SNMP and the user interface Was previously assigned to the same Existing configuration settings are used type of APM and are accessible from SNMP and the user interface Previously contained a different type of System generates a Module APM Misconfiguration alarm for the given slot See the Technical Reference for procedures in this situation Removing Replacing an I O Card _ Remove the APM from the housing see Removing Replacing an APM 2 Remove the cables from the I O card 3 Using a screwdriver loosen the upper and lower captive screws fastening the card to the housing s frame 4 Gently pull the I O card away from the midplane until it clears the housing 5 Align the replacement card with the upper and lower tracks of the slot Push gently towards the midplane until it stops and you cannot push the card any further 6 Alternately tighten each captive screw until both are snug 7 Reattach the cables as appropriate Power On Refer to the installation instructions that came with your housing to power on the equipment Warranty Sales Service and Training Information Contact your local sales representative service representative or distributor directly for
5. any help needed For additional information concerning warranty sales service repair installation documentation training distributor locations or Paradyne worldwide office locations use one of the following methods Internet Visit the Paradyne World Wide Web site at www paradyne com Be sure to register your warranty there Select Service amp Support gt Warranty Registration Telephone Call our automated system to receive current information by fax or to speak with a company representative Within the U S A call 1 800 870 2221 Outside the U S A call 1 727 530 2340 Document Feedback We welcome your comments and suggestions about this document Please mail them to Technical Publications Paradyne Corporation 8545 126th Ave N Largo FL 33773 or send e mail to userdoc eng paradyne com Include the number and title of this document in your correspondence Please include your name and phone number if you are willing to provide additional clarification Trademarks All products and services mentioned herein are the trademarks service marks registered trademarks or registered service marks of their respective owners 9109 A2 GN15 10 Copyright 1999 Paradyne Corporation
6. card with the upper and lower tracks of the slot Push gently towards the midplane until it stops and you cannot push the card any further Port 1 5 Slot 2 Slot Rear View Port 2 Port 3 Port 4 Port 5 98 15150 02 Port 6 3 There are two captive screws on the I O card Alternately tighten each screw until both are snug lt 98 15922 Connecting to the DDS Interface 1 Insert the other end of the cable Insert the RJ48S DDS network cable into the 4 wire DDS port The 2 port version provides two RJ48S 8 position modular keyed jacks while the 6 port version provides six into the DSU CSU RJ48S 8 position Modular Cabl 98 15970 Removing the Housing s Bezel 1 Depress the latch at the top of the housing to open the bezel 2 Lift upward to remove the bezel from the two slots at the bottom of the housing 496 15123 Save the bezel so it can be reattached once the APM has been installed NOTE The power supply is visible once the bezel is removed It provides low voltage power to the housing and its cards A WARNING If you need to remove the power supply module you must unplug the power cord from the power receptacle and from the rear of the housing before attempting to remove the module JA Front View without Bezel 98 15174 01 Installing the APM The APM can be installed in any slot except Slot 01 CAUTION You must
Download Pdf Manuals
Related Search