Home

Panasonic WV-SP302 Installation Guide

1. Connect a LAN cable category 5 or better STP to the network connector on the rear of the camera PAL models only This illustration represents WV SP306 D Connect the power supply Important e The 12 V DC power supply shall be insulated from the commercial AC power e The operating sound might be heard when the power is turned on however it does not indi cate any malfunction 26 When using 12 V DC power supply Loosen the screw of the power cord plug accessory Connect the cable of the 12 V DC power supply to the power cord plug Strip 3 mm to 7 mm 1 8 inches to 9 32 inches from the end of the wire and twist the stripped part of the wire Last S sufficiently to avoid short circuit P Ge Specification of cable wire 16 AWG 24 AWG oe TOPES WV SP306 Single core twisted e Check whether the stripped part of the wire is not exposed and is securely connected Tighten the screw of the power cord plug Connect the power cord plug to the 12 V DC power sup ply terminal on the rear of the camera FOR UL LISTED MODEL S ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY 12 V DC power cord plug accessory Important e Be sure to use the power cord plug provided with this product e Be sure to fully insert the power cord plug into the 12 V DC power supply terminal Otherwise it may damage the camera or cause malfunction e When in
2. Important e It may take for around 2 minutes to complete to upload the settings to the camera after clicking the Apply button The settings may be invalidated when the 12 V DC power supply is cut or when the LAN cable is disconnected before completing the upload In this case perform the settings again e When using a firewall including software allow access to all UDP ports 30 Troubleshooting Before asking for repairs check the symptoms with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below Power is not turned on Cause solution Reference pages When using DC power supply e Is 12 V DC power supply connected to the power supply terminal Check whether the connection is appropriately established e Is the AC adaptor in use compliant with the Specifications Check the Specifications regarding AC adaptor When using a PoE device for power supply e Are the PoE device and the network connector on the rear of the camera connected using a LAN cable 4 pair Check whether the connection is appropriately established Depending on the PoE device the power supply will stop when the demanded power exceeds its total power limit for all PoE ports Refer to the operating instructions of the PoE device in use 26 27 The focus cannot be adjusted Is the zoom ri
3. Web Browser Other Important Intel Core 2 Duo 2 4 GHz or faster recommended 512 MB or more A minimum of 1 GB memory is required when using Microsoft Windows 7 or Microsoft Windows Vista 10BASE T 100BASE TX 1 port Sound card when using the audio function Image capture size 1024 x 768 pixels or more Color 24 bit True color or better Microsoft Windows 7 Professional 64 bit Microsoft Windows 7 Professional 32 bit Microsoft Windows Vista Business SP1 32 bit Microsoft Windows XP Professional SP3 Windows Internet Explorer 8 0 Microsoft Windows 7 Professional 32 bit 64 bit Windows Internet Explorer 7 0 Microsoft Windows Vista Business SP1 32 bit Microsoft Internet Explorer 6 0 SP3 Microsoft Windows XP Professional SP3 CD ROM drive It is necessary to read the operating instructions and use the software on the provided CD ROM DirectX 9 0c or later Adobe Reader It is necessary to read the operating instructions on the provided CD ROM e When using a PC that does not meet the above requirements displaying of images may become slower or the web browser may become inoperable e Audio may not be heard if a sound card is not installed on a PC Audio may be interrupted depending on the network environment e Microsoft Windows XP Professional 64 bit Edition is not supported e When using IPv6 for communication use Microsoft Windows 7
4. These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples Cd This symbol might be used in combination with a chemical symbol In this case it complies with the requirement set by the Directive for the chemical involved For U S and Canada For Europe and other countries Panasonic System Communications Panasonic Corporation Company of North America http panasonic net Unit of Panasonic Corporation of North America Importer s name and address to follow EU rules www panasonic com business z For customer support call 1 800 528 6747 Panasonic Testing Centre Three Panasonic Way Secaucus Panasonic Marketing Europe GmbH New Jersey 07094 U S A Winsbergring 15 22525 Hamburg F R Germany Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2012 Ns0310 4012 3TR006448EZA Printed in China
5. WV SP302 Approx 390 g 0 86 Ibs Fine silver 501 1 3 type MOS image sensor Approx 1 3 megapixels 4 80 mm H x 3 60 mm V 3 16 inches H x 5 32 inches V Progressive WV SP306 Color 0 3 lx 0 03 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High 0 019 Ix 0 0019 footcandle F1 4 Auto slow shutter max 16 30 s AGC High 0 05 Ix 0 005 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High 0 003 Ix 0 0003 footcandle F1 4 Auto slow shutter max 16 30 s AGC High Converted value WV SP305 Color 0 3 Ix 0 03 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High BW Wide dynamic range Gain AGC Adaptive black stretch Light control mode setting Shutter speed Auto slow shutter Black amp white mode Simple black amp white mode White balance Digital noise reduction Video analytics Face detection Privacy zone Camera title on screen VMD alarm Auto back focus ALC lens drive Lens mount O Network Network Resolution WV SP806 WV SP305 0 019 Ix 0 0019 footcandle F1 4 Auto slow shutter max 16 30 s AGC High BW 0 2 Ix 0 02 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High 0 013 Ix 0 0013 footcandle F1 4 Auto slow shutter max 16 30 s AGC High Converted value WV SP302 Color 0 2 Ix 0 02 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High 0 013 Ix 0 0013 footcandle F1 4
6. Auto slow shutter max 16 30 s AGC High BW 0 13 Ix 0 013 footcandle F1 4 Auto slow shutter Off 1 30 s AGC High 0 009 Ix 0 0009 footcandle F1 4 Auto slow shutter max 16 30 s AGC High Converted value On Off On Low On Mid On High Off On Off Indoor scene Outdoor scene ELC Fix shutter Off 1 30 3 100 3 120 2 100 2 120 1 100 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 Off Max 2 30s Max 4 30s Max 6 30s Max 10 30s Max 16 30s On Off Auto1 Auto2 Only for WWV SP306 Off Auto Only for WV SP305 and WV SP302 ATW1 ATW2 AWC High Low On Off with the XML notification setting On Off up to 2 zones available Up to 16 characters alphanumeric characters marks On Off On Off 4 areas available Auto Preset Fix Only for WV SP306 DC drive CS mount 10BASE T 100BASE TX RJ45 connector Aspect ratio 4 3 H 264 1280 x 960 VGA 640 x 480 QVGA 320 x 240 max 30 fos MPEG 4 VGA 640 x 480 QVGA 320 x 240 max 30 fos JPEG 1280 x 960 VGA 640 x 480 QVGA 320 x 240 max 30 fos Aspect ratio 16 9 H 264 1280 x 720 640 x 360 320 x 180 max 30 fps JPEG 1280 x 720 640 x 360 320 x 180 max 30 fps MPEG 4 is not supported 33 Resolution WV SP802 Image compression method al al Transmission interval Audio compression method Bandwidth control Protocol OS 8 4 Browser Maximum concurrent access number FTP clie
7. DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REASON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE 7 LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE The network cameras WV SP800 series are designed to operate using a PC on a network 10BASE T 100BASE TX By connecting to a network LAN or the Internet images and audio from the camera can be moni tored on a PC via a network WV SP306 e Maximum image capture size 1280 x 960 Aspect ratio of 4 3 1280 x 720 Aspect ratio of 16 9 e Compatible with the auto back focus ABF function color mode black A white mode switch ing WV SP305 e Maximum image capture size 1280 x 960 Aspect ratio of 4 3 1280 x 720 Aspect ratio of 16 9 e Compatible with the focus assist F A function simple black amp white mode WV SP302 e Maximum image capture size 800 x 600 Aspect ratio of 4 3 640 x 360 Aspect ratio of 16 9 e Compatible with the focus assist F A function simple black amp white mode Note e lt is necessary to configure the network settings of the PC and its network environment to monitor images from the camera on the PC It is also necessary to install a web browser on the PC About notations The following notations are used when describing the functions limited for specified models The functions without the notations are supported by all models The functions with this not
8. hot and humid con ditions for a long time Failure to observe this causes component degradation resulting in life shortening of this product Do not expose this camera to direct heat sources such as a heater Handle this camera with care Do not drop this camera nor apply shock or vibration to this camera Failure to observe this may cause trouble About the PC monitor Displaying the same image on a CRT type monitor for a long time may damage the moni tor It is recommended to use a screen saver When an error is detected this product will restart automatically This product will be inoperable for around 2 minutes after the restart just as when the power is turned on Product disposal transfer Images saved on the SDHC SD memory card may lead to personal information leakage When it is necessary to dispose or give this product to someone even when for repair make sure that there is no data on the hard disk drives Cleaning this product body Be sure to turn off the power before cleaning Do not use strong abrasive detergent when cleaning this camera Otherwise it may cause discoloration When using a chemical cloth for cleaning read the caution provided with the chemical cloth product When the dirt is hard to remove use a mild detergent and wipe gently When the dirt is hard to remove use a mild detergent and wipe gently Then wipe off the remaining detergent with a dry cloth Transmission interval I
9. in accordance with the manufacturer s instruc tions 8 Do not install near any heat sources such as radiators heat registers stoves or other appara tus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been drop
10. initialized Before initializing the settings it is recommended to write down the settings in advance 16 Slowly rotate the lens clockwise to mount the lens and connect the lens cable to the ALC lens con nector of the camera Important ME SP302 e t is impossible to use lenses without the focus adjustment function or zoom lenses ALC lens connector CS mount lens option Protruded portion from mount face 220 mm 25 32 Zoom lock knob inches or less et Protruded portion from flange face 4 5 mm 5 32 inches or less 13 Pin No fe 1 Dump O oo 2 Dump O Focus ring LU one 24 Optional dedicated lens Product name Model number ALC lens for 1 3 type CCD cameras WV LZA62 2 2x vari focal High resolution If a lens for 1 3 type video camera other than the above is mounted and the camera is used at resolution of 1280 x 720 or higher the camera cannot achieve full performance of high resolu tion It is recommended to use a dedicated high resolution lens especially when the illuminance level of the photographic subject is low and the camera is used with the lens iris open How to adjust the focus Before adjustment reset the back focus position by holding down the auto back focus button for 5 seconds or more when the power is on This operation can also be performed on the setup menu Refer to the Operating Instructions PDF Adju
11. monaural e Recommended cable length 10 m 33 feet or less 25 Connect external devices to the EXT I O terminal Strip range When connecting an external device remove 9 mm 10 mm gt 11 32 inches 13 32 inches of the outer jacket of the cable __ and twist the cable core to prevent the short circuit first 9mm 10 mm Specification of cable wire 22 AWG 28 AWG Geer Single core twisted GND e Check whether the stripped part of the 2 AUX OUT wire is not exposed and is securely con nected Ann 4321 e ALARM IN DAY NIGHT IN ALARM OUT DAY NIGHT IN is only for WV SP306 Important e Do not connect 2 wires or more directly to a terminal When it is necessary to connect 2 or more wires use a splitter e Connect an external device with verifying that the ratings are within the specifications above e When using the EXT I O terminals as the output terminals ensure they do not cause signal col lision with external signals lt Ratings gt e ALARM OUT AUX OUT Output specification Open collector output maximum applied voltage 20 V DC Open 4 V 5 V DC by internal pull up Close Output voltage 1 V DC or less 50 mA or less e ALARM IN DAY NIGHT IN Input specification No voltage make contact input 4 V 5 V DC internally pulled up OFF Open or 4V 5V DC ON Make contact with GND required drive current 1 mA or more DAY NIGHT IN is only for WV SP306 LAN cable
12. or Microsoft Windows Vista Note e Refer to Notes on Windows Vista Windows 7 PDF for further information about system requirements for a PC and precautions when using Microsoft Windows 7 or Microsoft Windows Vista 10 Trademarks and registered trademarks Microsoft Windows Windows Vista Internet Explorer ActiveX and DirectX are either regis tered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Microsoft product screen shot s reprinted with permission from Microsoft Corporation Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United States and other countries Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries SDHC Logo is a trademark of SD 3C LLC All other trademarks identified herein are the property of their respective owners About copyright and license Distributing copying disassembling reverse compiling reverse engineering and also exporting in violation of export laws of the software provided with this unit are expressly prohibited Network security As you will use this unit connected to a network your attention is called to the following security risks Leakage or theft of information through this unit Use of this unit for illegal operations by persons with malicious intent I
13. smoke goes up from this product or the smell of smoke comes from this product stop the operation immediately and contact your dealer Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Do not insert any foreign objects This could permanently damage the apparatus Turn the power off immediately and contact qualified service personnel for service Select an installation area that can sup port the total weight Selecting an inappropriate installation surface may cause the product to fall down or topple over resulting in injury Installation work shall be started after sufficient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause a fall of the product resulting in injury Consult the dealer for the inspections Do not use this product in an inflammable atmosphere Failure to observe this may cause an explosion resulting in injury Avoid installing this bracket in the loca tions where salt damage occurs or corro sive gas is produced Otherwise the mounting portions will deterio rate and accidents such as a fall of this product may occur The measures of protection against a fall of this product shall be taken Failure to observe this may cause a drop result ing in injur
14. IC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrow head symbol within an equilat eral triangle is intended to alert the user to the presence of uninsulated dangerous volt age within the product s enclo sure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruc tions in the literature accompa nying the appliance Power disconnection Unit with or without ON OFF switches have power supplied to the unit whenev er the power cord is inserted into the power source however the unit is operational only when the ON OFF switch is in the ON position Unplug the power cord to disconnect the main power for all units For Canada This Class A digital apparatus complies with Canadian ICES 003 For U S A NOTE This equipment has been tested and found to comply with the limits for a Class A digi tal device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instr
15. OTHER USE ADDITIONAL NFORMATION MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP AWWW MPEGLA COM 13 14 Precautions for Installation Panasonic assumes no responsibility for injuries or property damage resulting from fail ures arising out of improper installation or operation inconsistent with this documenta tion This camera is designed to be used indoors This camera is not operable outdoors Do not expose this camera to direct sunlight for hours and do not install the product near a heater or an air conditioner Otherwise it may cause deformation discoloration and malfunc tion Keep this camera away from water and moisture Installation place Do not place the unit in the following places e Locations where it may get wet from rain or water splash e Locations where a chemical agent is used such as a swimming pool e Locations subject to humidity dust steam and oil smoke e Locations in a specific environment where a solvent or a flammable atmosphere exists e Locations where a radiation an X ray a strong radio wave or a strong magnetic field is generated e Locations where corrosive gas is pro duced Locations where it may be dam aged by briny air such as seashores e Locations where the temperature is not within 10 C to 50 C 14 F to 122 F e Locations subject to vibrations This prod uct is not designed for on vehicle use e Locations sub
16. Panasonic Installation Guide Network Camera Model No WV SP306 WV SP305 WW SP302 WW SP306E WW SP305E WW SP302E s Option This illustration represen EE OE DD Befor ano SA d nect or o per ma P oduc tld ee read these nstru Sieg ands ec ual for fut e The model number is abbreviated in some descriptions in this manual WARNING e Apparatus shall be connected to a mains sock et outlet with a protective earthing connection e The mains plug or an appliance coupler shall remain readily operable e To prevent fire or electric shock hazard do not expose this apparatus to rain or moisture e The apparatus should not be exposed to drip ping or splashing and that no objects filled with liquids such as vases should be placed on the apparatus e All work related to the installation of this prod uct should be made by qualified service per sonnel or system installers e For PERMANENTLY CONNECTED APPARATUS provided neither with an all pole MAINS SWITCH nor an all all pole circuit breaker the installation shall be carried out in accordance with all applicable installation rules e The connections should comply with local electrical code For U S and Canada WV SP306 WV SP305 WV SP302 For Europe and other countries WV SP306E WV SP305E WV SP302E UL listed model No WV SP306 WV SP305 WV SP302 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTR
17. Required cable gt LAN cable category 5 or better straight STP PAL models only Important e The video monitor is used for checking the adjustment of the angular field of view when install ing the camera or when servicing It is not provided for recording monitoring use e Use a switching hub or a router which is compliant with 10BASE T 100BASE TX e Power supply is required for each network camera When using a PoE device hub 12 V DC power supply is unnecessary 28 Configure the network settings Install the software Before installing the software read the readme file on the provided CD ROM first Software included on the provided CD ROM e Panasonic IP setting software Configure the network settings of the camera Refer to the following for further information e Viewer Software Network Camera View 4 It is necessary to install the viewer software Network Camera View 4 to display images on a PC Install the viewer software by double clicking the nwcv4setup exe icon on the provided CD ROM Configure the network settings of the camera using the Panasonic IP setting software It is possible to configure the network settings of the camera using the IP setup software on the provided CD ROM When using multiple cameras it is necessary to configure the network settings of each camera independently If the Panasonic IP setting software does not work configure the network settings of the camera and the PC individually
18. ation are available when using the model WV SP306 The functions with this notation are available when using the model WV SP305 The functions with this notation are available when using the model WV SP302 H 264 MPEG 4 and JPEG triple encoding H 264 MPEG 4 dual stream output and JPEG output can be simultaneously provided Either H 264 or MPEG 4 is selectable Wide dynamic range function This function compensates brightness so that it produces clearer images even if objects have vari ous illumination intensities Important e When the wide dynamic range function is activated noise may be increased in the dark area of the object Auto back focus ABF function Auto Back Focus ABF ensures easy installation and stable focus in both color and black amp white modes Focus assist F A function During the manual focus adjustment this function indicates the best focus position Color mode black amp white mode switching available Images will be displayed clearly even at night since the camera will be automatically switched from the color mode to the black and white mode under low illumination condition Important e The operating sound might be heard during the mode change however it does not indicate any malfunction Power over Ethernet function When connecting with a PoE Power over Ethernet device power will be supplied by simply con necting a LAN cable IEEE802 3af compliant Interactive communication with
19. audio By using the audio output connector and the microphone in connector receiving audio from the camera on a PC and transmitting audio from the PC to the camera is available SDHC SD memory card slot equipped It is possible to save H 264 videos and JPEG images on the SDHC SD memory card manually at an alarm occurrence or on a web browser It is also possible to save JPEG images at a network failure occurrence Download is possible Recommended SDHC SD memory card us page 34 About the user manuals There are 2 sets of operating instructions for the WV SP306 WV SP305 WV SP302 NTSC model WVW SP306E WV SPS05E WV SP802E PAL model as follows e Installation Guide Explains how to install and connect devices e Operating Instructions PDF Explains how to perform the settings and how to operate this camera Adobe Reader is required to read these operating instructions PDF on the provided CD ROM When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it WV SP306 WV SP305 WV SP302 or SP306 SP305 SP302 shown in the instructions and illustrations used in these operating instructions indicate the WV SP306 WW SP305 WV SP302 WV SPS306E WV SP305E WV SP302E The screens used in these operating instructions show the case of NTSC model System requirements for a PC CPU Memory Network Interface Audio interface Monitor OS
20. ch as white wall ubj with heavy flicker e In case the angular field of view has changed during adjustment close the FOCUS ADJUSTMENT menu once by pressing the focus assist F A button When the angular field of view changes the indicator values of PEAK HOLD and INDICATOR also change After fixing the angular field of view retry Step 3 19 20 Insert remove an SDHC SD memory card Important e Before inserting an SDHC SD memory card turn off the power of the camera first e When inserting an SDHC SD memory card make sure the direction e Before removing the SDHC SD memory card select Not use for About SD memory card on the SD memory card tab of Basic on the setup menu first Turn off the power after Not use selection and then unload the SDHC SD memory card When the SDHC SD memory card is inserted or removed with the power on data in the SDHC SD memory card may be damaged Operating Instructions Open the slide cover on the side of the camera and then insert an SDHC SD memory card into the SDHC SD memory card slot If necessary loosen the screw of the clamp for SDHC SD memory card and tighten the screw after rotating the clamp 90 clockwise Recommended tightening torque 0 19 N m 0 14 lbf ft This illustration represents WV SP306 Screw of the clamp for SDHC SD memory card Close the slide cover on the side of the camera To remove the SDHC SD mem
21. de cover Auto back focus button Focus assist button EZA I Tripod mount base Clamp for SDHC SD memory card lt Rear view gt Network connector f Audio output connector fiOBASE 17 oBASE TX Access indicator AUDIO OUT wate Microphone line input connector blinking at accessing ina O a ll INITIAL SET button D P ACT LINK Link indicator lighting at linking wearer sei wen AA Ana i tN Power indicator Monitor for adjustment 000 f CG 12 V DC power supply terminal Output connector GND 4 3 2 1 A ARM IN DAY NIGHT IN i y R PP iS AUX OUT LALA v OUT EXT I O terminals i 7 SDHC SD memory card error indicator ABF indicator Blinks when ABF is being activated SDHC SD memory card error indicator FA indicator Lights when the focus assist function is activated or when the focus ring is positioned near the best focus position EZA EZA a ez GND 4 3 2 1 ALARM IN AUX OUT ALARM OUT About the INITIAL SET button After turning off the power of the camera turn on the power of the camera while holding down this button and wait for around 5 seconds or more without releasing this button Wait around 2 minutes after releasing the button The camera will start up and the settings including the network settings will be
22. direction after continuously shooting a spotlight for a certain period the discolor ation may remain e When shooting fast moving subjects or performing panning tilting operations by mounting the camera on the pan tilt head objects crossing the shooting area may look to be bending askew MPEG 4 Visual Patent Portfolio License This product is licensed under the MPEG 4 Visual Patent Portfolio License for the personal and non commercial use of a consumer for i encoding video in compliance with the MPEG 4 Visual Standard MPEG 4 Video and or ii decoding MPEG 4 Video that was encoded by a consumer engaged in a personal and non commercial activity and or was obtained from a video provider licensed by MPEG LA to provide MPEG 4 Video No license is granted or shall be implied for any other use Additional information including that relating to promotional internal and commercial uses and licensing may be obtained from MPEG LA LLC See http www mpegla com AVC Patent Portfolio License THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO i ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD AVC VIDEO AND OR ii DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO NO LICENSE IS GRANTED OR SHALL BE MPLIED FOR ANY
23. e following place or the following subjects it may have difficulty adjusting the back focus position automatically In this case adjust the back focus position manually from the setup menu Refer to the Operating Instructions PDF for how to perform the auto back focus function from the setup menu e Place there the lens easily becomes dirty e Subj moving frequently e Subj with large illuminance change e Subj with low illuminance e Subj with reflection or extra brightness e Subj through a window e Subj with less contrast such as white wall e Subj with heavy flicker How to adjust the focus EZH EZY The focus is adjusted using the focus assist function The angle of view and focus can be adjusted in accordance with the distance between the camera lens and a photographic subject These adjustments shall be performed together with the camera angle adjustment Loosen the zoom lock knob and adjust the angle of view angular field of view in accordance with the photographic subject by moving the zoom lock knob and focus ring Note e The focus may not be adjusted appropriately when the RR zoom ring is positioned at the W or T end In this emeng geen case adjust the focus again by slightly moving the zoom ES FOCUS ring to the direction of T or W Fasten the zoom lock knob Press the focus assist button FOCUS ADJUSTMENT menu will be displayed The focus assist function will be activated to perform the
24. est conforme aux normes sp cifi es ou a tout autre document normatif conform ment aux dispositions des directives 2006 95 CE et 2004 108 CE Nosotros declaramos bajo nuestra nica responsabilidad que el producto a que hace referencia esta declaraci n est conforme con las normas u otros documentos normativos siguiendo las estipulaciones de las directivas 2006 95 CE y 2004 108 CE Noi dichiariamo sotto nostra esclusiva responsabilita che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive 2006 95 CE e 2004 108 CE Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende normen of andere normatieve documenten overeenkomstig de bepalingen van Richtlijnen 2006 95 EC en 2004 108 EC Vi erkl rer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standarder eller andre normative dokumenter i f lge bestemmelserne i direktivene 2006 95 EC og 2004 108 EC Vi deklarerar h rmed v rt fulla ansvar f r att den produkt till vilken denna deklaration h nvisar r i verensst mmelse med de standarder eller andra normativa dokument som framst lls i direktiv nr 2006 95 EC och 2004 108 EC Ilmoitamme yksinomaisella vastuullamme ett tuote jota tama ilmoitus koskee noudattaa se
25. fety wire is connected select a connection point resulting in that noth ing will hit people after the mount bracket is damaged The wire length shall be adjusted to remove slack Angle adjustment Be sure to loosen the screw of this product mount bracket when the camera angle is adjusted If the camera angle is changed when the screw is tight excessive force is applied to the camera mount bracket and camera and accordingly they may be damaged Be sure to tighten the screw securely after camera angle adjustment Radio disturbance When this product is used near TV radio anten na strong electric field or magnetic field near a motor a transformer or a power line images may be distorted and noise sound may be pro duced PoE Power over Ethernet Use a PoE hub device that is compliant with IEEE802 3af standard Router When connecting this product to the Internet use a broadband router with the port forward ing function NAT IP masquerade Refer to the Operating Instructions PDF for further information about the port forwarding function Time amp date setting It is necessary to set the time amp date before putting this product into operation Refer to the Operating Instructions PDF on the provided CD ROM for descriptions of how to perform the settings 15 Major operating controls lt Side view gt ALC lens connector Lens option SDHC SD memory card slot Sli
26. ional 32 bit 64 bit indows Internet Explorer 7 0 icrosoft Windows Vista Business SP1 32 bit crosoft Internet Explorer 6 0 SP3 icrosoft Windows XP Professional SP3 JPEG JPEG ZS SS ZS ZEZ 14 Depends on network conditions Alarm image transmission FTP periodic transmission When the FTP transmission is failed backup on an optional SDHC SD memory card is available Up to 16 camera images can be displayed simultaneously on a multi screen Manufactured by Panasonic SDHC memory card 4 GB 8 GB 16 GB 32 GB SD memory card 256 MB 512 MB 1 GB 2 GB except miniSD card and microSD card 1 Either H 264 or MPEG 4 is selectable 2 Transmission for 2 streams can be individually set in the same compression method 3 Refer to Notes on Windows Vista Windows 7 PDF for further information about system requirements for a PC and precautions when using Microsoft Windows 7 or Microsoft Windows Vista 4 When using IPv6 for communication use Microsoft Windows 7 or Microsoft Windows Vista Standard accessories Installation Guide this document sote ut a Moir nen detente 1 pe Waranty EE 1 pe CD ROM EE 1 pe A 1 pc 1 NTSC models only 2 The CD ROM contains the operating instructions PDFs and the software 3 This label may be required for network management The network administrator shall retain the code label The following parts are used duri
27. ject to condensation as the result of severe changes in temperature Be sure to remove this product if it is not in use Shielded STP LAN cables must be used with this unit to ensure compliance with EMC standards PAL models only Before installation e The camera mount bracket described on page 23 shall be used to mount the cam era e When this camera and camera mount bracket are mounted on a ceiling or a wall use the screws described on page 23 The screws to be used are not provided Prepare the screws according to the mate rial structure strength and other factors of the mounting area and the total weight of objects to be mounted e Ensure that the mounting surface anchor and screws are sufficiently strong e Do not mount this product on a plaster board or a wooden section because they are too weak If this product is unavoidably mounted on such a section the section shall be sufficiently reinforced Screw tightening e The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area e Do not use an impact driver Use of an impact driver may damage the screws or cause tightening excessively e When a screw is tightened make the screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure tightening is enough and there is no backlash Fall prevention measures When the external sa
28. mage transmission interval may become slow depending on the network environment PC performance shooting subject access num ber etc About SDHC SD memory card e Before inserting the SDHC SD memory card turn off the power of this product first Otherwise it may cause malfunction or damage data recorded on the SDHC SD memory card Refer to page 20 for descriptions of how to insert remove an SDHC SD memory card e When using an unformatted SDHC SD memory card format it using this camera Recorded data on the SDHC SD memory card will be deleted when formatted If an unformatted SDHC SD memory card or an SDHC SD memory card formatted with other devices is used this product may not work properly or performance deterioration may be caused Refer to the Operating Instructions PDF for how to for mat a SDHC SD memory card e When some SDHC SD memory cards are used with this product the product may not work properly or performance deterio ration may be caused Use the SDHC SD memory cards recommended in page 34 Code label The code labels accessory are required at inquiry for trouble Use caution not to lose these labels It is recommended to paste one of the labels onto the CD ROM case About the MOS image sensor e When continuously shooting a bright light source such as a spotlight the color filter of the MOS image sensor may have deteri orated and it may cause discoloration Even when changing the fixed shooting
29. ng installation procedures Power Cord ug Safety wire plate for ceiling safety wire lug TO Wallonie a a EN A Wire lug fixing screws M2 5 x 8 mm 5 16 inches oe 35 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products packaging and or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste For proper treatment recovery and recycling of old products and used batteries please HE take them to applicable collection points in accordance with your national legislation and the Directives 2002 96 EC and 2006 66 EC By disposing of these products and batteries correctly you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling For more information about collection and recycling of old products and batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union
30. ng turned to the W or T end Adjust the focus again by slightly moving the zoom ring to the direc tion of T or W 18 19 31 Specifications O Basic Power source Power consumption Ambient operating temperature Ambient operating humidity Monitor output for adjusting the angular field of view External I O terminals Microphone Line input For microphone input For line input Audio output Dimensions Mass Finish Camera Image sensor Effective pixels Scanning area Scanning system Minimum illumination 12 V DC PoE IEEE802 3af compliant WV SP306 12 V DC 350 mA PoE 4 4 W Class 2 device WV SP305 WV SP302 12 V DC 270 mA PoE 3 4 W Class 2 device FOR UL LISTED MODEL S ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY 10 C to 50 C 14 F to 122 F Less than 90 no condensation VBS 1 0 V p p 75 Q composite signal RCA jack ALARM IN DAY NIGHT IN ALARM OUT AUX OUT x1 each DAY NIGHT IN is only for WV SP306 23 5 mm monaural mini jack Input impedance Approx 2 kQ Applicable microphone Plug in power type Supply voltage 2 5 V 0 5 V Input level Approx 10 dBV 23 5 mm stereo mini jack monaural output Output impedance Approx 600 Q Line level 75 mm W x 65 mm H x 132 5 mm D 2 31 32 inches W x 2 9 16 inches H x 5 1 4 inches D excluding connectors ter minals WV SP306 Approx 410 g 0 91 lbs WV SP305
31. nt Multi screen Compatible SDHC SD memory card option Aspect ratio 4 3 H 264 800 x 600 VGA 640 x 480 QVGA 320 x 240 max 30 fos MPEG 4 VGA 640 x 480 QVGA 320 x 240 max 30 fos 800 x 600 VGA 640 x 480 QVGA 320 x 240 max 30 fos Aspect ratio 16 9 H 26 640 x 360 320 x 180 max 30 fps JPEG 640 x 360 320 x 180 max 30 fps MPEG 4 is not supported H 264 MPEG4 Image quality Low Normal Fine Transmission type Unicast Multicast Video bit rate Constant bit rate 64kbps 128kbps 256kbps 384kbps 512kbps 768kbps 1024kbps 1536kbps 2048kbps 3072kbps 4096kbps 8192kbps Unlimited only in H 264 mode Frame rate priority 1fps Sfps 5fps 7 5fps 10fps 12fps PAL models 15fps 20fps 30fps Image quality O SUPER FINE 1 FINE 2 3 4 5 NORMAL 6 7 8 9 LOW 10 steps 0 9 Transmission type PULL PUSH 0 1 fps 30 fps JPEG frame rate will be restricted when dis playing both JPEG and H 264 MPEG 4 images G 726 ADPCM 32kbps 16kbps Unlimited 64kbps 128kbps 256kbps 384kbps 512kbps 768kbps 1024kbps 2048kbps 4096kbps 8192kbps IPv6 TCP IP UDP IP HTTP RTP FTP SMTP DNS NTP SNMP IPv4 TCP IP UDP IP HTTP RTSP RTP RTP RTCP FTP SMTP DHCP DNS DDNS NTP SNMP crosoft Windows 7 Professional 64 bit crosoft Windows 7 Professional 32 bit crosoft Windows Vista Business SP1 32 bit icrosoft Windows XP Professional SP3 indows Internet Explorer 8 0 icrosoft Windows 7 Profess
32. nterference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks Use this unit in a network secured by a firewall etc If this unit is connected to a network that includes PCs make sure that the system is not infect ed by computer viruses or other malicious entities using a regularly updated anti virus pro gram anti spyware program etc Protect your network against unauthorized access by restricting users to those who log in with an authorized user name and password Apply measures such as user authentication to protect your network against leakage or theft of information including image data authentication information user names and passwords alarm mail information FTP server information and DDNS server information After the unit is accessed by the administrator make sure to close the browser Change the administrator password periodically Do not install the camera in locations where the camera or the cables can be destroyed or damaged by persons with malicious intent Precautions Refer installation work to the dealer Installation work requires technique and experi ences Failure to observe this may cause fire electric shock injury or damage to the prod uct Be sure to consult the dealer Stop the operation immediately when something is wrong with this product When
33. of the angle field P e The monitor output connector is provided of view only for checking the adjustment the angle field of view on the video monitor when installing the camera or when servicing It Connect to y b ee the video is not provided for recording monitoring monitor etc use mll e Black bands may appear at the top bot tom right and left of the screen There is no problem with adjustment since the This illustration represents WV SP306 angle field of view is not affected e The video output on the monitor for adjust ment does not guarantee the video perfor mance or image quality Connect the microphone to MIC LINE IN for use of the audio reception function Input impedance Approx 2 KQ Recommended cable length 1 m 3 3 feet or less for microphone input 10 m 83 feet or less for LINE input Recommended microphone Plug in power type microphone option Connect a monaural mini plug 3 5 mm e Supply voltage 2 5 V 0 5 V e Recommended sensitivity of microphone 48 dB 3 dB 0 dB 1 V Pa 1 kHz Important e Connect disconnect the audio cables and turn on the power of the camera after turning off the power of the audio output devices Otherwise loud noise may be heard from the speaker Connect an external speaker with amplifier to the audio output connector for use of the audio transmission function Connect a stereo mini plug 93 5 mm Audio output is
34. on the Network page of the setup menu Refer to the Operating Instructions PDF for further information Important e When using Microsoft Windows Vista the Windows Security Alert window may be displayed when starting the IP setup software In this case disable User Account Control from the con trol panel e For the security enhancement the MAC address IP address of the camera to be configured will not be displayed when around 20 minutes have passed after turning on the power of the cam era when the effective period is set to 20min only in the Easy IP setup e Panasonic IP setting software is inoperable in other subnets via the same router e This camera cannot be displayed or set with an older version of the IP setup software version 2 XX 29 Start the Panasonic IP setting software by double clicking the EasylpSetup exe icon on the provided CD ROM Click the IP setting button after selecting the Drees MAC address IP address of the camera to be configured SS Note e When using a DHCP server the IP address assigned to the camera can be displayed by clicking the Refresh button of the IP setting software e When a duplicate IP address is used the corre CG sponding MAC address IP address will De dis played shaded Complete each network setup item and click the Apply button Note e When using a DHCP server it is possible to set DNS to AUTO
35. optimum adjustment When the focus ring is positioned near the best focus position the position will automatically be memorized as the PEAK HOLD position When the focus ring is moved the current focus position will be indicated on INDICATOR Adjust the focus position so that the indicator value goes close to the PEAK HOLD position g When the indicator value goes to the best focus position BEST FOCUS will be displayed in reverse at the lower right corner of the screen Press the focus assist button again to close the FOCUS ADJUSTMENT menu No operation for 3 seconds also closes the menu Note e The most common use of a varifocal lens Note that the adjustment method is different depending on the type For further information refer to the operating instructions for the lens to be used e Depending on the lens to be used if the zoom ring is fully rotated in the W direction the periphery may become dark In such a case rotate the zoom ring in the T direction for read justment e When shooting the following subjects close the FOCUS ADJUSTMENT menu by pressing the focus assist F A button again and adjust the focus to obtain the best focus position while monitoring images from the camera e Place where the lens easily becomes dirty e Subj moving frequently or having large illuminance change e Subj with low illuminance ubj with reflection or extra brightness ubj through a window ubj with less contrast su
36. ory card rotate the clamp for SDHC SD memory card 90 counterclockwise push the memory card to unlock it and remove the memory card from the SDHC SD memory card slot Installation Connect the safety wire The following is an example of safety wire connection Important e Be sure to install the safety wire Ask your dealer for installation e ege Mounting screws For mounting on ceiling Tripod mount base Remove the tripod mount base on the top Safety wire plate of the camera for ceiling accessory Fi Nx Wire engaging is lt hole rear Align the tripod mount base with the safety wire plate for ceiling accessory and attach Witeengading them to the camera with the mounting hole front screws Important e Use the detached mounting screws to attach the tripod mount base When using different length screws it may damage the camera or cause the camera to fall Recommended tightening torque 0 39 N m 0 29 lbf ft Engage the safety wires 2 pieces with the wire engaging holes front and rear respectively Wire engaging hole Safety wire Pass the ring part of the safety wire 2 Pass the other end of the safety wire through the wire engaging hole through the ring part of the safety wire 21 For mounting on wall Put the tripod mount base on the bottom of the camera Secure the safety wire lug for wall accessory to the camera mount screw hole with the wire lug fixing screw acces
37. ped Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPECIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 8 UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT
38. sory _ Wire lug fixing Important E engaging is screw accessory e Be sure to use the provided fixing screws for the safety wire lug and the removed Ge lug ee or wal screws for the camera mount base peng screw accessory When using different length screws it may damage the camera or cause the camera to fall Recommended tightening torque 0 39 N m 0 29 Ibf ft Leave these holes untouched gt Mounting screws Tripod mount base Engage the safety wire with the wire engaging hole Safety wire Wire engaging hole LS Pass the ring part of the safety wire 2 Pass the other end of the safety wire through the wire engaging hole through the ring part of the safety wire 22 Camera mounting The camera is mounted on the camera mount bracket and the safety wire is secured Important e The installation area shall be strong enough to hold the camera and camera mount bracket e The camera mount bracket shall be mounted on the foundation part of the construction or a part with adequate strength e To prevent the mounting strength from becoming lower do not use wooden screws to secure the camera mount bracket Secure the camera mount bracket to an installation position and mount the camera on the camera mount bracket Prepare mounting screws according to the material of the area where the camera mount brack et is to be installed The installation method may be different depending on the ma
39. st the view angle and focus coarsely by adjusting the zoom and focus of the lens to center a subject in the screen and then press the auto back focus button on the side of the camera page 16 or perform the auto back focus function from the setup menu Refer to the Operating Instructions PDF for how to perform the auto back focus function from the setup menu 17 18 Note e The most common use of a varifocal lens and a zoom lens Note that the adjustment method is different depending on the type For further information refer to the operating instructions for the lens to be used Adjust the back focus after positioning the zoom ring at the T end and positioning the focus ring at a step short of the F end Depending on the lens to be used if the zoom ring is fully rotated in the W direction the periphery may become dark In such a case rotate the zoom ring in the T direction for read justment When images in the near infrared light area change from the color mode to the black amp white mode out of focus may be occurred according to the nature of optical property In this case the focus can be corrected by selecting Auto or Preset for Adjusting method on the setup menu The focus will not automatically be adjusted according to the illumination level change once the focus is corrected Refer to the Operating Instructions PDF for how to configure the Adjusting method setting on the setup menu e When shooting in th
40. stalling the camera make sure that excessive force is not applied to the power cable e Be sure to use an AC adaptor compliant with the Specifications regarding power source and power consumption Is page 32 When using PoE IEEE802 3af compliant Connect a LAN cable category 5 or better straight STP between a PoE device Such as a hub and the network connector of the camera PAL models only Important e Use all 4 pairs 8 pins of the LAN cable e The maximum cable length is 100 m 328 feet e Make sure that the PoE device in use is compliant with IEEE802 3af standard e When connecting both the 12 V DC power supply and the PoE device for power supply PoE will be used for power supply e When disconnecting the LAN cable once reconnect the cable after around 2 seconds When the cable is quickly connected the power may not be supplied from the PoE device 27 Connection example when connecting to a network using a PoE hub Video monitor for adjustment use only Speaker with amplifier option WE PoE device hub 0000000000 0 o El LAN cable o o gt category 5 or better straight STP lt PC Microphone option e LAN cable category 5 T E Q LA or better straight STP Speaker with amplifier option LAN cable category 5 or Le better straight STP Microphone option L A Video monitor for adjustment use only lt
41. terial of the area where the bracket is to be installed e When installing on steel Fix with bolts and nuts M6 or M8 e When installing on concrete Fix with anchor bolts M6 or M8 Important e When the camera mount bracket is mount ed on a wall be sure to observe the mounting height described on the illustra E i tion 2m 90 cm 9 5 feet _ or more 23 Put the connection hook of the safety wire on the safety wire plate or the safety wire lug secured on the foundation part of the construction or a part with adequate strength Important e The safety wire shall be adjusted to remove slack lt For mounting on ceiling gt lt Mounting sample gt Foundation part of construction or part with adequate strength Connection hook Connection hook Camera mount bracket lt For mounting on wall gt lt Mounting sample gt Recommended screw M6 Minimum pull out strength 196 N 44 06 Ibf Safety wire Safety wire lug Safety wire Foundation part of construction or part with adequate strength 24 Connection Caution e FOR UL LISTED MODEL S ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY Before starting the connection turn off the power of this camera and the devices to be connected Before start the connection prepare the required devices and cables Connect the RCA pin cable to the monitor output connector for adjustment on the e Important rear only for adjustment
42. uction man ual may cause harmful interference to radio com munications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter ference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or peripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment ForU S A The serial number of this product may be found on the surface of the unit You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006 95 EC and 2004 108 EC Wir erkl ren in alleiniger Verantwortung daf das Produkt auf das sich diese Erklarung bezieht mit den folgenden Normen oder normativen Dokumenten bereinstimmt Gem f den Bestimmungen der Richtlinie 2006 95 EC und 2004 108 EC Nous d clarons sous notre propre responsabilit que le produit auquel se r f re la pr sente d claration
43. uraavia standardeja tai muita ohjeellisia asiakirjoja jotka noudattavat direktiivien 2006 95 EC ja 2004 108 EC s d ksi Vi erkl rer oss alene ansvarlige for at produktet som denne erkl ringen gjelder for er i overensstemmelse med f lgende normer eller andre normgivende dokumenter som f lger bestemmelsene i direktivene 2006 95 EC og 2004 108 EC Contents Important safety instructions 5 Limitation of Iabilttv 6 Disclaimer f warranty eiee a Eed ged 6 Eelere ee e a N s a EE 6 leie uge LEE 7 Main fUNCtIONS EE 7 About the user manuals vicio ese 8 System requirements for a DC 9 Trademarks and registered trademarks A 10 About copyright andlicenSe cocotero candados p ERR ee racer a aa a aa aaea Aa a r aaraa raaraa tinana 10 NotWork SECU Void 10 PreCaUtlons aos 11 Precautions for Installation insire inse ENEE abe area arvana beeen Peaeeeengeee 14 Major operato controls canine es BERRA Rs a ea A AETA 16 LESS IMOUNTING WEE 17 Insert remove an SDHC SD Memory Card 20 Installation gerett dree atari riada iris ete COMMOCTION EE Configure the network settings Troubleshooting Specifications Standard accessories Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install
44. y Be sure to install the safety wire The exclusively designed mount bracket shall be used Failure to observe this may cause a drop result ing in injury or accidents Use the exclusively designed mount bracket for installation The screws and bolts shall be tightened to the specified torque Failure to observe this may cause a drop result ing in injury or accidents Do not install this product in locations subject to vibration Loosening of mounting screws or bolts may cause a fall of the product resulting in injury Install this product in a location high enough to avoid people and objects from bumping the product Failure to observe this may cause a drop result ing in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause fire or injury Do not rub the edges of metal parts with your hand Failure to observe this may cause injury 11 Turn the power off when do wiring of this product Failure to observe this may cause electric shock In addition short circuit or wrong wiring may cause fire Turn the power off when cleaning of this product Failure to observe this may cause injury Precautions for use This system is designed to be used indoors This product is not operable out doors This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Do not use this camera in

Panasonic WV-SP302 Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents