Panasonic WV-CW304L Installation Guide
Contents
1. Caution To ensure waterproof tighten the front cover to align w arrow with the mark position Important Install the sunshield Make sure that the arrow on the location indicating label is aligned with the installation indicator on the rear cover before the front cover is screwed tightly Otherwise the camera can not be water proofed Make sure that the sealing ring is not stripped or slanted and if it occurs please put the sealing ring to where it is Make sure there is no dust or other dirty things on the sealing rings and if it occurs please remove them Please strip the protective layer clung on the transparent portion of the front cover after completing the installation and after that do not touch the transparent portion of the front cover directly with your hands Recommended tightening torque 1 0 N m 7 38 Ibf ft 21 Performing each setting item in the setup menu should be completed in advance to use this unit Perform the settings for each item in accordance with the installation conditions and customer requirements List of setup menu Setup item CAMERA ID CAMERA SCENE 1 SCENE 2 ALC ELC SHUTTER AGC SENS UP WHITE BAL DNR D amp N IR VMD SYSTEM SYNC PRIVACY ZONE STABILIZER EL ZOOM UPSIDE DOWN LDC BACK FOCUS ED em SPECIAL CHROMA GAIN AP GAIN PEDESTAL PIX OFF CAMERA RESET SER NO LANGUAGE 22 Description This item specifies the camera title The ca2. R Resistance of copper wire Q m Va DC output voltage of power supply unit DC current consumption A See specifications Resistance of copper wire at 20 C Copper wire 24 22 20 18 16 size AWG 0 205 mm 0 325 mm 0 519 mm 0 833 mm 1 307 mm Resistance 0 083 0 052 0 033 0 020 0 013 O m Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when installing the camera with cables exposed or installing it under the eaves The camera body is waterproof but the cable ends are not waterproof Be sure to use the supplied waterproof tape at the points where the cables are connected to apply waterproof treatment in the following procedure Failure to observe this or use of a tape other than the provided waterproof tape such as a vinyl tape may cause water leakage resulting in malfunction W DAN DY PORE RT BOW Video output cable Note How to wind the supplied waterproof tape a accessory otretch the tape by approx twice see the Stretch the tape to illustration and wind it around the cable Insufficient J about twice tape stretch causes insufficient waterproofing To install this product outdoors be sure to waterproof the cables Waterproof grade IEC IP66 2X or equivalent is applied to this product only when it is installed correctly as described in these operating instructions and appropriate waterproof treatment is applie
3. 30 Vertical 5 Adjusting angle Horizontal 360 Vertical 0 90 Azimuth 115 190 Ambient operating temperature 10 C to 50 C Ambient operating humidity Less than 90 Dimensions 79 mm x 245 mm H Mass about 1050 g Camera title English letter numbers and symbols up to 16 characters Light control mode setting ALC ALC ELC ELC Back Light Compensation ON OFF ABS ON OFF Shutter speed OFF 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 1 120000 s Auto gain control ON HIGH MID LOW OFF Sensitivity up OFF AUTO x2 x4 x6 x10 x16 x32 FIX x2 x4 x5 x10 X16 x 82 x604 x128 x256 x512 OFF AUTO x2 x4 x6 x10 x16 x32 White balance ATW1 ATW2 AWC 29 WV CW324LE WV CW3914LE WV CWS3O4LE Digital noise reduction LOW HIGH Day amp Night IR AUTO1 AUTO2 ON OFF IR LED irradiation distance o0m 20m IR LED lights OFF AUTO FIX Video motion detection OFF MOTION DETECTION SCENE CHANGE Number of scene file 2 Privacy zone ON 1 ON 2 OFF Image stabilizer ON OFF Electronic zoom ON up to 2x OFF Upside down ON OFF Lens distortion correction Oto 255 Back focus setup ABF MANUAL Camera IP66 IEC60529 Waterproof Only when installation work specified in this book is properly performed and appropriate waterproof treatment is performed
4. Fini Main body Aluminum die cast resin metallic silver coating inish Front cover section clear part Polycarbonate resin X Values of mass and dimensions are approximate The specification is subject to change without notice 30 Standard accessories GE FOU eR X TDO Installation Guide this DOOR 1 pc Does coal NU YON TOR Se es TITTEN T pG The CD ROM contains the operating instructions and installation guide PDF The following parts are used during installation procedures V EDI GONE P S azi f t ala acte kl E eat adv l ca tl sa cu e n e lit pa E Ps e n e E tan 1 DG B OU RR TT m 1 pc instalation template 8 PEE TOO OUR 1 pc SHE W AS NO eodein iiv eam in eve a ak me UM DRE EUM Mesi E Me LEM eMe ME eee bene e eee UNE 1196 Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product Disposing of this product correctly will help to save valuab
5. your hand Failure to observe this may cause injury Do not touch this product the power cord or the connected cables during thunder even in the process of work Failure to observe this may cause electric shock The measures of protection against snowfall shall be taken In areas where lots of snow accumulates the weight of snow may cause the product to fall resulting in injury or accidents Protect the product against snowfall by installing under eaves The screws and fixed parts must be securely tightened Failure to observe this may cause the product to fall resulting in injury The measures of protection against a fall of this product shall be taken Failure to observe this may cause a drop resulting in injury or accidents Do not damage the power cable Do not damage fabricate twist stretch bundle or forcibly bend the power cable Do not place heavy objects Keep away from heat sources Use of the damaged power cable may cause electric shock short circuit or fire Consult the dealer for repair Turn the power off when cleaning this product Failure to observe this may Cause injury Precautions for use This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humi
6. 08 EC Nosotros declaramos bajo nuestra unica responsabilidad que el producto a que hace referencia esta declaraci n esta conforme con la norma u otro documento normativo siguiendo las estipulaciones de la directiva 2004 108 CE Vi deklarerar harmed vart fulla ansvar for att den produkt till vilken denna deklaration hanvisar ar i verensst mmelse med standarddokument eller annat normativt dokument som framstalls i direktiv 2004 108 EC IlImoitamme yksinomaisella vastuullamme ett tuote jota tama ilmoitus koskee noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa jotka noudattavat direktiivin 2004 108 EC s d ksi Noi dichiariamo sotto nostra esclusiva responsabilit che il prodotto a cui si riferisce la presente dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle disposizioni della direttiva 2004 108 CE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral trian gle is intended to alert the user to the presence of uninsulated dan gerous voltage within the prod uct s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral tr
7. ET RET TOP END Screen transition diagram GED Top screen MODEL WV CW304L CAMERA ID OFF CAMERA 1 SYSTEM SPECIAL LANGUAGE END SETUP DISABLE CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ 27 s T 11 SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ELC 1 SHUTTER AGC ON LOW SENS UP OFF WHITE BAL ATW1 DNR HIGH D amp N IR AUTO2 1 VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN OFF LDC e e ee RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN eters s L LO AP GAIN PEDESTAL PIX OFF CAMERA RESET gt PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END 27 Troubleshooting Before asking for repairs confirm the causes with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below Symptom Cause solution Reference page e Is there a wall or other reflecting surface or When the IR LED lights a object near the camera including areas 18 part or all of the screen not displayed in images Operating appears blurred Adjust the camera angle so that light Instructions from the IR LED is not reflected
8. LATING TO THE PRODUCT 2 PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER 8 UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REASON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE Preface This product is a 1 3 type CCD D N infrared CCTV camera Connection of this product to a video monitor allows users to use this product as a monitoring camera e WV CWS24LE WV CWS14LE with function of color black and white mode switch and back focus adjustment e WV CWGOLLE with function of color black and white mode switch About notations The following notations are used when describing the functions limited for specific models The functions without the notations are supported by all models GED The functions with this notation are available when using the model WV CW324LE GE The functions with this notation are available when using the model WV CW814LE GED The functions wit
9. Panasonic Installation Guide Color CCTV Camera Model No WV CW32 4 L E WV CW314LE WV CW304LE This illustration represents WV CW324LE WV CW314LE WV CW304LE Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004 108 EC Wir erkl ren in alleiniger Verantwortung da das Produkt auf das sich diese Erklarung bezieht mit der folgenden Norm oder normativen Dokument Ubereinstimmt GemaB den Bestimmungen der Richtlinie 2004 108 EC Wij verklaren als enige aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende norm of ander normatief dokument overeenkomstig de bepalingen van Richtlijn 2004 108 EC Nous d clarons sous notre propre responsabilit que le produit auquel se r f re la pr sente d claration est conforme a la norme sp cifi e ou a tout autre document normatif conform ment aux dispositions de la directive 2004 108 CE Vi erklaerer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standard eller andre normative dokumenter i folge bestemmelserne i direktiv 2004 1
10. UP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN LDC RET TOP END BACK FOCUS screen BACK FOCUS SETUP ABF gt PUSH SET MANUAL ADJ C L B W FIX RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN kana Tan LO AP GAIN PEDESTAL PIX OFF J CAMERA RESET gt PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH SET RET TOP END 25 26 Screen transition diagram Gap Top screen MODEL WV CW314L CAMERA ID OFF CAMERA SYSTEM BACK FOCUS 1 SPECIAL LANGUAGE J END SETUP DISABLE CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ 27 s T 11 SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC t SHUTTER OFF AGC ON LOW SENS UP OFF WHITE BAL ATW1 DNR HIGH D amp N IR AUTO2 VMD OFF RET TOP END SYSTEM SETUP screen SYSTEM SETUP SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL ZOOM OFF UPSIDE DOWN LDC RET TOP END BACK FOCUS screen BACK FOCUS SETUP ABF gt PUSH SET MANUAL ADJ C L B W FIX RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN sa dos a LO AP GAIN PEDESTAL PIX OFF J CAMERA RESET gt PUSH SET SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE ENGLISH S
11. al brightness level Corrects image defects such as flaws Restores the settings in the setup menu to the default settings Displays the serial number of this unit Selects a language to be used in the setup menu Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor The description below explains how to operate the setup menu basically Screenshots of WV CW324LE are shown as an example Screenshot 1 Hold down the SET button for about 2 seconds to call up the top screen of the setup menu MODEL CAMERA ID CAMERA SYSTEM BACK FOCUS SPECIAL LANGUAGE WV CW324L OFF END SETUP DISABLE Screenshot 2 The setup mode changes to ENABLE and the setup menu becomes ready to be set MODEL CAMERA ID CAMERA SYSTEM BACK FOCUS SPECIAL WV CW324L OFF LANGUAGE END SETUP ENABLE Step 1 Press the UP or DOWN button to move the cursor to END Step 2 Press the RIGHT button to move the cursor to SETUP and press the SET button to change the setup mode from DISABLE to ENABLE Step 3 Move the cursor to the item to be set and oress the SET button 23 Screenshot 3 The selected setup screen in the setup menu appears on the screen 24 CAMERA SETUP SCENE1 ALC ELC ALC I SHUTTER AGC SENS UP WHITE BAL RET TOP END Note lf the top screen
12. angle between TELE and WIDE Note The focus may not be adjusted smoothly when the zoom adjustment ring is extremely close to the end of W direction T direction At this time slightly adjust the zoom adjustment ring towards the T direction W direction and then adjust the focus Q Tighten the zoom knob 3 Adjust the focus knob to get the optimal angular field of view between NEAR and FAR 4 Press the set button on the side of the camera which will automatically focus Note Press the set button to enter into the ABF function If the set button is pressed continuously for more than 2 seconds the setup menu will be displayed Note The ABF function is not available over the entire focus range Be sure to perform approximate adjustment of the view angle before manual focusing and then press the ABF button to enable the ABF function For the following subjects select ELC control method and then manually adjust the focus e Frequently moving subject e Subject with large illuminance change e Subject with low illuminance e Too bright or reflective subject e Subject through a window e Place where the lens easily becomes dirty e Subject with less contrast such as white wall e Subject with remarkable depth e Subject with heavy flicker e Subject with horizontally parallel lines such as a shutter Install the front cover Installation Location Rear cover Front cover indicating mark indicating label
13. d The mount brackets are not waterproofed 17 Adjustment Be sure to view the monitor for adjustment when the camera angle is adjusted Supply power to this unit connect the monitor for adjustment e g a small LCD to the monitor output jack and aqjust the camera angle turn off the power after view angle adjustment for safety CD Loosen the 2 fixing screws of the front cover to remove the front cover Sunshield 2 Unscrew and remove the front cover lt WV CW324LE WV CW314LE gt Front cover 3 Connect the adjustment monitor output jack to monitor output jack with 3 5 mm miniature plug mono channel locally procured 18 Important e This video output is intended for confirmation of view angle etc during installation or repair service and not for recording or monitoring Note e Monitor output jack has higher priority than video output connector Video cannot be output through the video output cable after connecting the adjustment monitor 4 7 Tilting lock screw Panasonic WV CW314L Yow lock screw Panning lock screw Warning Label 4 Repeat the steps 1 and 2 to adjust the camera angle 1 Loosen the panning lock screw and rotate the camera head horizontally to adjust panning 2 Loosen the tilting lock screw and rotate the camera head vertically to adjust tilting 3 Loosen the yow lock screw and rotate the cam
14. dity Recommended operating temperature 10 C 50 C Do not expose this product to direct heat sources such as a heater Do not touch the front cover transparent cover with your bare hands A dirty cover causes deterioration of picture quality Handle this product with care Do not drop this product nor apply shock or vibration to this product Failure to observe this may cause trouble If a strong shock or vibration is applied to the front cover it may cause damage or allow water to enter this product Noise on monitor This product is equipped with a super sensitive CCD Therefore noise may appear on the monitor This phenomenon is not trouble Discoloration on the CCD color filter When continuously shooting a bright light source such as a spotlight the color filter of the CCD may have deteriorated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for a certain period the discoloration may remain Do not aim this product at strong light sources A light source such as a spot light causes a blooming light bleeding or a smear vertical lines Smear Bright subject Blooming 10 Cleaning this product body Turn the power off when cleaning this product Do not use strong abrasive detergent when cleaning this product Otherwise it may cause discoloration When using a chemical cloth for cleaning read the caution provided wi
15. e The subject may be too close to the camera When the IR LED lights Adjust the distance between the 18 the camera switches camera and the subject between color mode and Make sure there is no other strong Operating black and white mode infrared light resource in external Instructions environment e Are the power cord and coaxial cable connected appropriately Check whether the connection is appropriately established e ls the monitor connected Check whether the monitor is connected e Are there smudginess or damage on the transparent cover No image displayed Check whether the transparent cover is clean Blurred image e s the focus adjusted correctly 20 Check if the focus is adjusted correctly e s the lens of the camera soiled with dirt or dust Check whether the lens of the camera is clean Damaged power cord sheathing W W V V Vv Heated portion of power line e The power cord power connector or consisting of power cord power plug is damaged Continuous use connector and power plug of the damaged cord connector or plug during use may cause electric shock or fire Disconnect the power plug immediately The temperature of power and request repair from your dealer cord rises or falls when the power cord is bent or stretched during use e ls the connected system controller set to multiplexed vertical drive VD2 Check whether the connected system cont
16. e camera mount bracket is to be installed In this case wood screws and nails should not be used Recom mended tightening torque M4 1 60 N m 1 18 lbf ft e Required pull out capacity of a single screw bolt is 196 N 44 06 Ibf or more e f a wall or ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced 14 Installation Affix the installation template label accessory to the ceiling or wall and use a pen to mark the positions of the screws and cable mounting hole in the ceiling or wall Remove the installation template label and attach the camera with 3 screws locally procured Installation template label Cable access hole aL cw wv Camera fixing screw x3 locally procured Prepare screws locally procured according to the condition of the attachment position Attach the safety wire to the foundation or other parts of the building with sufficient strength Recommend Spring washer screw M3 accessory Panasonic WV CW314L Foundation or other Safety wire parts of the building with sufficient strength Foundation or other parts of l the building with Spring sufficient strength washer oafety wire Hecommend screw M3 1 Connections Connect the video output Important Video output e Be sure to turn off the power of each connector device b
17. efore connecting e Be sure to secure the coaxial cable connectors Power cord Connect a coaxial cable locally procured to the video output connector Connect the power supply Connect the two color conductor cable of the camera to the power supply The colors and functions of the conductors are shown below Color 12V DC 24 V AC Brown Positive Live Blue Negative Neutral Important e The power supply of 24 V AC 12 V DC shall be insulated against 220 to 240 V AC e The power supply is automatically switchover either 24 V AC or 12 V DC No setting is required with this camera Connection of power cord When connecting the power cord use connectors that are designed for the power cord and be careful not to let the power cord fall off In addition waterproofing work is needed at the joint e g wrapping waterproof tape around the joint Cable length and wire gauge 24 V AC The recommended cable length and wire gauge are shown in the table for reference The voltage supplied to the power terminals of the camera should be within 19 5 V AC and 28 V AC Copper wire 24 22 20 18 16 size AWG 0 205 mm 0 325 mm 0 519 mm 0 833 mm 1 307 mm 16 Length approx 12VDC Calculation of the relation among the cable length resistance and power supply The voltage supplied to the camera shall be between 10 8 V DC and 16 V DC 10 8 V DC lt Vi 2 R xl x L lt 16V DC L Cable lenoth m
18. era head horizontally to adjust panning 4 Tighten the yow lock screw panning lock screw and tilting lock screw after camera angle adjustment Important e After camera angle adjustment the yow lock screw panning lock screw and tilting lock screw shall be securely tightened Recommended tightening torque 1 8 N m 1 33 lbf ft 19 20 Note Do not put your hands on the safety warning label when the camera angle is adjusted unless your hands will be clamped when the front portion of camera falls Use a hexagonal wrench with width across flats of 3 mm locally procured to loosen or tighten the yow lock screw panning lock screw and tilting lock screw Approximately 1 rotation of loosening the yow lock screw panning lock screw and tilting lock screw allows camera angle adjustment Do not loosen the screws beyond necessity The camera body shall be held when the yow lock screw panning lock screw or tilting lock screw is loosened Focus adjustment shall be performed at the same time panning and tilting adjustments are performed Adjust the angular field of view and the focus gp ar Adjust the angular field of view in accordance with the distance between the camera lens and a photographic subject These adjustments shall be performed together with the camera angle adjustment Set button 7 U WIT D y T 7 c ei Zoom knob Focus knob CD Loosen the zoom knob and adjust to the best view
19. ere k e ai Tr ere at n ab e on ki at ka li af ke ter 7 Trademarks and registered Tace ne it uuu L u ak e a ak a La e ank ae l ka ank a L kn a kk Fd 7 OO its e ia ka a iu aun a a e a a e rere a a ki a ey reer rer ree pa ki ke ki 8 Precautions Tor lnn A OG uk u u a ka heey n aka TOO e kk n a a e al at das ek at sa e lk ba a 11 POS WAYOM ccc ata a cca al total ata a e tala a teka ay ka na st dwa iran d 19 miis 9 ccu e u A TT TIT TCR ER IHNEN 14 gezielt l CMS WONN ei RET TI TT TT TTE 16 IDEE RO A REm 18 SON TON Mi u mene ee ee eee en eee ete ee I Dd IDEM LU MILENA IDE kaa ro MS Ze LON LO ON Ti u a at a tt tum 22 BAYO OD Sl e NEN ia ky ka ta ed pit l apa pak aka tard UT TT 2 Soreen ransition diagram QD na iiti bo edat aV POR wx RYE natin Dew ECC VDO rd apa ekta 25 Screen transition diagram GER 26 Screen transition diagram GR 27 bret c es T I AN A E ETA ae tak do ee A A EE A TA 20 PECHE MONS T TP 29 Standard accessorieS a aa aa aaa aa aaa aa aa n rese te reseau pase e sese ese enn 30 Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not block any ventilation openings Install in accordance with the manufacturer s instruc tions 6 Do not install near any heat sources such as radiators heat registers stoves or other appara tus includi
20. h this notation are available when using the model WV CWS04LE Features Introduction of newly developed high resolution CCD The introduction of the newly developed CCD with 976 horizontal pixels has led to a horizontal resolution of as high as 650 TV lines Auto back focus ABF function Gb a It is possible to adjust the back focus automatically by operating the set button of this camera or the setup menu Day Night conversion function equipped No setup change is required at night because the image automatically changes from the color mode to the black and white mode at low illuminance IR LED equipped The equipped infrared LED makes it possible to monitor at zero Ix Comply with Standard IP66 dustproof and waterproof With dustproof and waterproof designing the camera can be mounted under eaves or rainy and damp area or bad conditions with dust flying Motion detection function VMD equipped The motion of an object is detectable The acts of covering the camera with a cloth a cap or other acts and changing the camera direction during surveillance can be detected Note e The VMD function is not the dedicated function to prevent thefts fires etc We are not responsible for any accidents or damages caused by applying the function for the above purposes About the user manuals The operating instructions of the camera consist of 2 sets this book and operating instructions PDF This book explains how to install t
21. he camera Refer to the Operating Instructions PDF on the provided CD ROM for descriptions of how to perform the unit settings Adobe Reader is required to read PDF When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it Trademarks and registered trademarks Adobe Acrobat Reader and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or othe countries Precautions Refer installation work to the dealer Installation work requires technique and experiences Otherwise injury or damage to this product may result Be sure to consult the dealer Stop operation immediately when something is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product continued use will result in fire injury or damage to the product Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Do not insert any foreign objects This could permanetly damage this product Turn the power off immediately and contact qualified service personnel for service Select an installation area that can support the total weight Selecting an inappropriate installation surface ma
22. iangle is intended to alert the user to the presence of important operating and mainte nance servicing instructions in the literature accompanying the appliance Vi erklaerer oss alene ansvarlige for at produktet som denne erklaeringen gjelder for er i overensstemmelse med f lgende norm eller andre normgivende dokumenter som f lger bestemmelsene i direktiv 2004 108 EC WARNING All work related to the installation of this product should be made by qualified service personnel or system installers To prevent injury this apparatus must be securely attached to the floor wall ceiling in accordance with the installation instructions e The installation shall be carried out in accordance with all applicable installation rules This product has no power switch When turning off the power turn off a Power Supply or remove a power cable e The connections should comply with local electrical code Contents Important safety 1InStruCHiOnS ee e e nk uni uisa iussu co bstes uo debat a m pick bx ocu ede d eun 4 Efe Mt wie secs ARR o Disclaimer ot warranty UL aaa au a Ubera Mae MN RT RUNTIME EPIRI EAT DRIN ER At o l LO t ki s 6 ja 81819 128 q 8142 1118 q FORT YA PT MAN WE Psi Ea A E A ON PW MN PW ME FONN MN ME MW Fa A MW AP 6 ir ki aka a u u tb 6 OU NE US NAN VON uuu abi ke a ake r
23. ightening is enough and there is no backlash Locally procure the screws Screws are not supplied with this product Prepare the screws according to the material structure strength and other factors of the mounting area and the total weight of objects to be mounted 11 Radio interference When the camera is used near TV radio antenna strong electric field or magnetic field near a motor or a transformer images may be distorted and noise sound may be produced In such a case run the camera cable through specialized steel conduit tubes Take notice of humidity Install this product when the humidity is low If this product is installed at a high humidity the inside may be exposed to moisture and the front cover may become foggy Conduit If the camera is used outdoors be sure to use conduits and run the cables inside the tubes to protect the cables from direct sunlight 12 Major operating controls Safety wire 49 Camera mount Sunshield bracket Video output connector Panasonic wy CW314L Power cord EK eov Yow lock screw iaa aen Tilting lock Panning lock screw SCrew WV CW324LE WV CW314LE gt Packino Monitor output Set IR LED Lens jack button 13 lt WV CW304LE gt Set button Packing Monitor output Lens jack The camera can be directly mounted on the wall or ceiling Important e Prepare the mounting screws according to the material of the area where th
24. le resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappro priate waste handling Please contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal 31 Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg Germany Panasonic System Networks Co Ltd 2013 SLO313 0 PGQX1305ZA Printed in China
25. mera title that indicates the camera location and other information about the camera is created with alohanumeric characters and symbol and then displayed on the screen Performs the camera operation settings Selects a scene file It is possible to register and save the settings as a scene file in case that it is necessary to change the settings such when shooting at night Selects the method of controlling the quantity of light in accordance with the lens to be used Specifies the electronic shutter speed Specifies gain adjustment Specifies electronic sensitivity enhancement Specifies white balance adjustment Selects the level of the digital noise reduction function Performs each setting regarding the black and white mode such as switching between color and black and white images Performs settings regarding VMD Video Motion Detection Performs the settings regarding the camera system such as synchronization and privacy zone Only INT method can be used Hides undesired portions in the camera shooting area Decides whether or not to enable the image stabilizer Switches the electronic zoom on and off Flips the camera images vertically or horizontally Adjusts the Lens distortion correction to convert the image so that it matches the square monitor Selects the adjustment method and fine adjustment method for back focus Adjusts the chroma level color density Adjusts the aperture level Adjusts the pedest
26. ng amplifiers that produce heat 7 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 8 Only use attachments accessories specified by the manufacturer 9 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over a S Ma 3125A 10 Unplug this apparatus during lightning storms or when unused for long periods of time Limitation of liability THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVEMENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPECIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RE
27. of the setup menu is called up with the operation buttons while the camera is operated the setup mode is always DISABLE to prevent operation errors To perform settings in the setup menu change the setup mode to ENABLE The cursor is a reversely highlighted part Step 4 Perform the settings for each item e Selection of setting item Press the UP or DOWN button to move the cursor e Change of settings Press the RIGHT or LEFT button e Display of advanced setup screen Press the SET button when is attached to the target setting item e Return to previous setup screen Move the cursor to RET and press the SET button e Return to the top screen Move the cursor to TOP and press the SET button to display the top screen of the setup menu Step 5 Move the cursor to END and press the SET button to return to the camera image screen or wait about 5 minutes and the setup menu will automatically close Screen transition diagram Gi Top screen MODEL WV CW324L CAMERA ID OFF CAMERA 1 SYSTEM BACK FOCUS 1 SPECIAL LANGUAGE J END SETUP DISABLE CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ 27 s T 11 SPACE POSI RET TOP END RESET CAMERA SETUP screen CAMERA SETUP SCENE1 ALC ELC ALC t SHUTTER OFF AGC ON LOW SENS UP OFF WHITE BAL ATW1 DNR HIGH D amp N IR AUTO2 l VMD OFF RET TOP END SYSTEM SET
28. roller is set correctly Black line in image Specifications General WV CW324LE IWV CW314LE WV CWS3O04LE Power source and power consumption 24 V AC 50 60 Hz 5 2 W 12 V DC 560 mA 24 V AC 3 2 W 12 V DC 320 mA Image sensor 1 3 type interline transfer CCD Effective pixels 976 H x 582 V ocanning area ocanning system 4 8 mm H x 3 6 mm V 2 1 interlace scanning line 625 lines Scanning frequency Horizontal 15 625 kHz Vertical 50 00 Hz Synchronization Internal INT Multiplexed vertical drive VD2 cannot be set Horizontal resolution 650 TV lines Vertical resolution 400 TV lines Video output 1 0 V p p PAL composite video signal 75 Q Signal to noise ratio 52 dB AGC OFF Minimum illumination Focal length 0 08 Ix color mode 0 008 Ix black and white mode infrared LED light off 0 Ix black and white mode infrared LED light on 9 mm 22 mm 2 8 mm 10 0 mm 0 15 Ix color mode 0 015 Ix black and white mode infrared LED light off 0 Ix black and white mode infrared LED light on 2 8 mm Aperture ratio F1 6 WIDE F3 0 TELB F1 3 WIDE F3 1 TELE F2 0 Angular field of view Horizontal 30 57 WIDE 12 25 TELE Vertical 23 28 WIDE 9 20 TELE Horizontal 100 50 WIDE 27 39 TELE Vertical 3 51 WIDE 20 45 TELE Horizontal 101
29. rrosive gas is produced Locations where it may be damaged by briny air such as seashores Locations where the temperature is not within 10 C to 50 C Locations subject to vibrations This product is not designed for on vehicle use Locations subject to condensation as the result of severe changes in temperature Avoid installing this product in a place with a high level of noise Installation near an air conditioner an air cleaner a vending machine or the like causes noise Avoid installing and connecting during a lightning storm Otherwise an electric shock or fire may be caused Do not damage the power plug or cable Keep the camera cable away from the lighting cable Failure to observe this may cause noise Be sure to remove this product if it is not in use Design and engineer the power supply system to turn on off the power of this product The product has no power switch When installing the product use a power supply device equipped with the ON OFF switch for servicing Screw tightening e The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area e Do not use an impact driver Failure to observe this may cause overtightening and consequently damage to the screws e When a screw is tightened make the screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure t
30. th the chemical cloth product Cleaning the lens Use a lens cleaning paper used to clean camera lenses or lenses of spectacles When using solvent use an alcohols solvent and do not use a thinner or a glass cleaner Synchronous mode setting Image synchronous mode of this camera indicates internal synchronization INT only Set the multiplexed vertical drive VD2 as OFF when the camera is connected to the system controller of the company Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particu lar environment e Make sure that the installation area is strong enough to hold the product such as a concrete ceiling Install the camera in the foundation area of the architecture or where sufficient strength is assured If a wall or ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced Avoid installing this product in the following locations e Locations where a chemical agent is used such as a swimming pool Locations subject to steam and oil smoke such as a kitchen Locations near flammable gas or vapor e Locations where radiation or x ray emissions are produced Locations where co
31. y cause the product to fall down or topple over resulting in injury Installation work shall be started after sufficient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents Consult the dealer for the inspections Do not use this product in an atmosphere of flammable gases Failure to observe this may cause injury by explosion Avoid installing this product in locations where it is subject to damage by salt or corrosive gas Otherwise the mounting fixtures will deterio rate causing the product to fall down and leading to accidents This product shall be installed ina vibration free place Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury Install this product in a location high enough to avoid people and objects from bumping the product Failure to observe this may cause a drop resulting in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause injury or fire Turn the power off when do wiring of this product Failure to observe this may cause electric shock A short circuit or wrong wiring may cause fire Tighten screws and mounting fixtures to the specified torque Failure to observe this may cause a drop resulting in injury or accidents Do not rub the edges of metal parts with
Download Pdf Manuals
Related Search