Panasonic WV-CF504 Installation Guide
Contents
1. THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR NON INFRINGEMENT OF THE THIRD PARTY S RIGHT THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS CHANGES ARE ADDED TO THE INFORMATION HEREIN AT ANY TIME FOR THE IMPROVE MENTS OF THIS PUBLICATION AND OR THE CORRESPONDING PRODUCT S Disclaimer of warranty IN NO EVENT SHALL Panasonic System Networks Co Ltd BE LIABLE TO ANY PARTY OR ANY PERSON EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT FOR THE CASES INCLUDING BUT NOT LIMITED TO BELOW 1 ANY DAMAGE AND LOSS INCLUDING WITHOUT LIMITATION DIRECT OR INDIRECT SPE CIAL CONSEQUENTIAL OR EXEMPLARY ARISING OUT OF OR RELATING TO THE PROD UCT PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE USER UNAUTHORIZED DISASSEMBLE REPAIR OR MODIFICATION OF THE PRODUCT BY THE USER 4 INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED DUE TO ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT 5 ANY PROBLEM CONSEQUENTIAL INCONVENIENCE OR LOSS OR DAMAGE ARISING OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY 6 ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATION BEING A PHOTOGENIC SUBJECT DUE TO VIO2. END Step 2 Press the right button to move the cursor to SETUP and press the setting button to change the setup mode from DISABLE to ENABLE 29 The setup mode changes to ENABLE and the setup menu becomes ready to be set Step 3 MODEL WV CF504 CAMERA ID Move the cursor to the item to be set and CAMERA SYSTEM press the setting button BACK FOCUS SPECIAL LANGUAGE END SETUP ENABLE The selected setup screen in the setup menu appears on the screen Step 4 Perform the settings for each item Selection of setting item CAMERA SETUP pei end Press the up or down button to move the ATWI cursor Amo Change of settings Press the right or left button RET TOP END Display of advanced setup screen Press the setting button when is attached to the target setting item Return to previous setup screen Move the cursor to RET and press the setting button Return to the top screen Move the cursor to TOP and press the setting button Note f the top screen of the setup menu is called up with the operation buttons while a camera image is displayed the setup mode is always DISABLE to prevent operation errors To configure the settings in the setup menu change the setup mode to ENABLE Step 5 The cursor is a reversely highlighted part return to the camera image screen move the cursor to END and press the setting but to
3. procedure Do not shrink the cable entry Seal until it has been ascertained that unit is functioning Cord length and wire gauge 24 V AC The recommended cord length and copper wire size are shown in the table for reference The voltage supplied to the camera should be between 19 5 V AC and 28 V AC Recommended wire gauge for 24 V AC line Copper wire 24 22 20 18 size AWG 0 22 0 33 mm 0 52 mm 0 83 mm Length of m 20 30 45 75 cable approx feet 66 100 150 250 12V DC The recommended resisance and copper wire size are shown in the table for reference The voltage supplied to the camera should be between 10 8 V DC and 16 V DC Resistance of copper wire 20 68 Copper wire size 24 22 20 118 AWG 0 22 mm 0 33 mm 0 52 mm 0 83 mm Resistance 0 m 0 078 0 050 0 08 0 018 T k Resistance 0 0 024 0 015 0 009 0 005 Use the formula below to calculate the power cord and power supply L R Va Il shall satisfy the inequalitty below 10 8 V DC lt Va 2 R x x L lt 16 V DC L Cord length m feet R Resistance of copper wire O ft Va DC output voltage of power supply unit l DC current consumption A See spec ifications 27 About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit Perform th
4. a certain period the discoloration may remain Do not aim this product at strong light sources A light source such as a spot light causes a blooming light bleeding or a smear vertical lines Smear Blight subject Blooming Cleaning this product body Turn the power off when cleaning this product Do not use strong abrasive detergent when cleaning this product Otherwise it may cause discoloration What to do if OVER HEAT appears on the display This message indicates that the inside of the camera has become extremely hot Immediate ly turn off the power of the camera and contact your dealer Precautions for installation The following points as well as the contents of Warning and Caution shall be observed Panasonic assumes no responsibility for injuries or property damage resulting from fail ures arising out of improper installation or operation inconsistent with this documenta tion Installation work shall be performed in accordance with the technology standard of the electric installation This product is designed to be used indoors This product is not operable outdoors Do not expose the product to direct sunlight for hours and do not install the product near a heater or an air conditioner Otherwise it may cause deformation discoloration and malfunc tion Keep the product away from water and moisture Installing place Contact your dealer for assistance if you are unsure of an appropriat
5. again 25 26 Cautions POWER SUPPLY FOR UL LISTED MODEL S ONLY CONNECT THIS TO 24 V AC OR 12 V DC CLASS 2 Be sure to connect the grounding lead to the GND terminal Power cord Video output cable Video output connection The video output connector is connected to the monitor or other system devices with a coaxial cable locally procured The maximum extensible length is shown in the table Type of coaxial RG 59 U RG 6 U RG 11 U RG 15 U cable 8C 2V 5C 2V 7C 2V 10C 2V Recommended m 250 500 600 800 maximum cable length feet 825 1650 1980 2640 Power connection Precaution The following connections should be made by qualified service personnel or system installers in accordance with local electrical code NEC 725 51 for NTSC model Brown Live Blue Neutral 7 Green Yellow GND To GND only for 24 V AC BNC connector To 24 V AC 12 V DC power supply BNC connector BNC connector To VIDEO IN Wire colors amp functions Camera power cord Wire color 24 V AC 12V DC Brown 24 V AC L Positive Blue 24V AC N Negative Green yellow To GND Cautions Be sure to connect the GND grounding lead of the camera and grounding terminal of the power supply when using a 24 V AC power source Shrinking the cable entry seal is a onetime
6. of the focus PRIVACY ZONE Hides undesired portions in the camera shooting area STABILIZER Decides whether or not to enable the image stabilizer EL ZOOM Toggles the electronic zoom on and off UPSIDE DOWN Enables the vertical and horizontal flip function BACK FOCUS Selects the back focus setting type and performs fine adjustment 28 Setup item Description SPECIAL CHROMA GAIN Adjusts the chroma level AP GAIN Adjusts the aperture level PEDESTAL Adjusts the pedestal brightness level HUE Adjusts the chroma phase hue level PIX OFF Corrects image defects such as flaws CAMERA RESET Restores the settings in the setup menu to the default settings SER NO Displays the serial number of this unit LANGUAGE Selects a language to be used in the setup menu 1 NTSC model only Basic operation Hold down the setting button for more than 2 seconds to call up the top screen of the setup menu MODEL WV CF504 CAMERA ID OFF CAMERA SYSTEM BACK FOCUS SPECIAL LANGUAGE END SETUP DISABLE The description below explains how to operate the setup menu basically The operations in the setup menu are performed with the operation buttons gt page 13 after call ing up the setup menu on the connected video monitor The operations in the setup menu can also be performed through the system controller option Step 1 Press the up or down button to move the cur sor to
7. F1 4 WIDE 0 0006 Ix 0 00006 footcandle sensitivity up x32 at F1 4 WIDE Converted value 50 dB AGC Off 33 Dynamic range Monitor output Functions Camera title Light control mode setting Super Dynamic 5 Electronic shutter speed AGC Sensitivity up White balance Digital noise reduction Color BW ntelligent VMD i VMD Number of scene file Privacy zone mage stabilizer Electronic zoom mage flip Auto back focus Display language Lens Type Focal length F number Focus range Angle of view Adjusting angle NTSC 52 dB typ Super Dynamic 5 ON PAL 54 dB typ Super Dynamic 5 ON VBS 1 0 V p p 75 NTSC PAL composite RCA jack Up to 16 characters alohanumeric characters marks ALC ALC ON ON i VMD OFF NTSC OFF 1 60 1 100 1 250 1 500 1 1000 1 2000 1 4000 1 10000 s PAL 1 50 1 120 1 250 1 500 1 1000 1 2000 1 4000 1 10000 s ON HIGH MID LOW OFF OFF AUTO 2 x4 x6 x10 x16 x32 FIX x2 x4 x6 x10 x16 x32 ATW1 ATW2 AWC HIGH LOW AUTO1 AUTO2 ON OFF Motion detection Object abandonment removal detection Scene change detection 2 ON 1 ON 2 OFF ON OFF ON Up to 2x OFF ON OFF ABF MANUAL switching between color and BW interlocking JAPANESE ENGLISH FRANCAIS ESPANOL DEUTSCH 2x variable focal lens 3 8 mm 8 0 mm F1 4 WIDE F1 8 TELE 1 2m Horizo
8. LATION OF PRIVACY WITH THE RESULT OF THAT SURVEILLANCE CAMERA S PICTURE INCLUDING SAVED DATA FOR SOME REA SON BECOMES PUBLIC OR IS USED FOR ANY PURPOSE 7 LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE 2 3 Contents Important safety instructions Limitation of liability Disclaimer of warranty iouis deae etse e liebe ocv es sm DES Features au E ee VE PEE CERTE ee ce 7 About thie u serimianualss entrenar ae Ince pu ede dece e EVEN aaa pan Raapa 8 Trademarks and registered 8 Precautioris a E EUER EMI 9 Precautions for installation esee eene 11 Major operating controls and their functions 2 22 2 22 3 13 Miele 15 Detaching th dome GOV6r Rete aval i tinal a ene te ede 18 Gamera installation erm p set n ert et 20 Make a connecti n usu RE RRR NU EPI EE EXE VE aaye 26 About the setup melius ce ce cones ea S pasqa 28 Troubleshootilig i Ree A ee er eee a ee VE Eee ERE Tuta 32 Specifications rire eet em ob ronde t em eed
9. ON TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrow head symbol within an equilat eral triangle is intended to alert the user to the presence of uninsulated dangerous volt age within the product s enclo sure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instruc tions in the literature accompa nying the appliance NOTE This equipment has been tested and found to comply with the limits for a Class A digi tal device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environ ment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction man ual may cause harmlul interference to radio com munications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter ference at his own expense FCC Caution To assure continued compliance example use only shielded interface cables when connecting to computer or pe
10. Panasonic Installation Guide Color CCTV Camera VW V CF 504 WV CF504E Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual WARNING This apparatus must be earthed Apparatus shall be connected to a mains sock et outlet with a protective earthing connection The mains plug or an appliance coupler shall remain readily operable To prevent fire or electric shock hazard do not expose this apparatus to rain or moisture The apparatus should not be exposed to drip ping or splashing and that no objects filled with liquids such as vases should be placed on the apparatus All work related to the installation of this prod uct should be made by qualified service per sonnel or system installers For PERMANENTLY CONNECTED APPARATUS provided neither with an all pole MAINS SWITCH nor an all all pole circuit breaker the installation shall be carried out in accordance with all applicable installation rules The connections should comply with local electrical code For U S and Canada WV CF504 For Europe and other countries WV CF504E UL listed model No WV CF504 For Canada 4 This Class A digital apparatus complies with Canadian ICES 003 For U S A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTI
11. Synchronization Resolution Minimum illumination Signal to noise ratio NTSC 24 V AC 60 Hz 12 V DC PAL 24V AC 50 Hz 12V DC 24 V 3 4 W 12 V DC 280 mA 10 C to 50 C 14 F to 122 F Less than 90 no condensation VBS 1 0 V p p 75 NTSC PAL composite BNC connector 9151 mm x 129 mm 05 15 16 inches x 5 1 16 inches H Main body 0 9 kg 2 0 lbs including camera attachment 60 g 0 13 Ibs Main body ABS plastic Dome cover Clear polycarbonate resin 1 8 type interline transfer CCD NTSC 976 H x 494 V PAL 976 x 582 V 4 8 mm H x 3 6 mm V 3 16 inches x 5 32 inches 2 1 interlace Horizontal 15 734 kHz NTSC 15 625 kHz PAL Vertical 59 94 Hz NTSC 50 00 Hz PAL INT internal sync VD2 LL Power supply synchronization Phase adjustable Horizontal 650 TV lines typ color mode 700 TV lines or more BW mode Vertical 350 TV lines or more NTSC at center 400 TV lines or more PAL at center When using clear dome cover Color Mode 0 1 Ix 0 01 footcandle at F1 4 WIDE 0 003 Ix 0 0003 footcandle sensitivity up x32 at F1 4 WIDE BW mode 0 01 Ix 0 001 footcandle at F1 4 WIDE 0 0003 Ix 0 00003 footcandle sensitivity up x32 at F1 4 WIDE When using smoke dome cover option Color Mode 0 2 Ix 0 02 footcandle at F1 4 WIDE 0 006 Ix 0 0006 footcandle sensitivity up x32 at F1 4 WIDE BW mode 0 02 Ix 0 002 footcandle at
12. ading to accidents Use the specified mount bracket Failure to observe this may cause a drop result ing in injury or accidents Do not rub the edges of metal parts with your hand Failure to observe this may cause injury Tighten screws and mounting fixtures to the specified torque Failure to observe this may cause a drop result ing in injury or accidents 10 Precautions for use This product is designed to be used indoors This product is not operable outdoors This product has no power switch When turning off the power turn off a circuit breaker To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity Recommended operating temperature 35 95 or lower Do not expose this product to direct heat Sources such as a heater Handle this camera with care Do not drop this camera nor apply shock or vibration to this camera Failure to observe this may cause trouble Do not touch the dome cover with your bare hands A dirty dome cover causes deterioration of pic ture quality Discoloration on the CCD color filter When continuously shooting a bright light Source such as a spotlight the color filter of the CCD may have deteriorated and it may cause discoloration Even when changing the fixed shooting direction after continuously shooting a spotlight for
13. amera Adobe Reader is required to read these operating instructions PDF on the provided CD ROM When the Adobe Reader is not installed on the PC download the latest Adobe Reader from the Adobe web site and install it WV CF504 or CF504 shown in the instructions and illustrations used in these operating instruc tions indicates the WV CF504 WV CF504E The screens used in these operating instructions show the cases of NTSC model Trademarks and registered trademarks Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries Precautions The following points as well as the con tents of Warning and Caution shall be observed Refer installation work to the dealer Installation work requires technique and experi ences Otherwise injury or damage to this product may result Be sure to consult the dealer Do not insert any foreign objects This could permanetly damage this product Turn the power off immediately and contact qualified service personnel for service Do not attempt to disassemble or modify this product Failure to observe this may cause fire or electric shock Consult the dealer for the repair or inspections Stop operation immediately when some thing is wrong with this product When smoke goes up from this product or the smell of smoke comes from this product con tinued use will result in fire injur
14. and the back focus is automatically adjusted INDICATOR XXXX FOCUSING 23 24 To perform fine adjustment of the back focus after the ABF operation indicator goes off and automatic back focus is adjusted use the right or left button Note No operation for 10 seconds or more automatically clears the focus position indicator To change the angle of view by moving the zoom adjustment ring also move the focus lock knob to adjust the focus The originally adjusted focus may be slightly off depending on the iris state resulting from the focal depth of the lens In such a case open the aperture by darkening the subject as much as possible in the same way of taking picture and then adjust the focus Defocus can be prevent ed Use of of BACK FOCUS in the setup menu Operating Instructions PDF allows users to adjust the focus optimally in the range of the capability to automatically follow the vari ation in illuminance The out of focus level in the near infrared light region may be higher than that in the visible light region Setting lt B W of BACK FOCUS SETUP to AUTO or PRESET in the setup menu Operating Instructions PDF allows users to adjust the focus in both the near infrared light and visible light regions The variation in illuminance is not followed after focus adjustment Mount the dome cover and inner dome CD Align the I on the dome cover with the fixin
15. box Mount the camera on the two gang junction box by fixing 4 screws locally procured rs page 15 83 5 mm 3 9 32 inches Note For mounting on the wall mount the attachment with the dent facing upward For installation on the ceiling the model No will be indicated on the opposite side of the dent of the attachment Make sure the direction for installation Installing the camera directly on the ceiling or wall Mount the camera by fixing 4 screws locally procured rs page 15 P Cable access hole we 27mm 1 1 16 inches Camera attachment Ps 2 Center of camera attachment 16 Using the ceiling mount bracket WV Q175 option It is possible to reduce the exposed portion of the camera body using the ceiling mount bracket option Refer to WV Q175 Operating Instructions or Camera Installation rs page 20 for how to mount the camera Using the ceiling mount bracket WV Q105 option PAL model only Refer to WV Q105 Operating Instructions and Camera Installation page 20 for how to mount the camera in case of using the ceiling mount bracket option Roof space WV Q105 option Fixing screw a 4 pcs WV Q105 supplied t3 Cable tie accessory Ceiling board such Safety wire Gamea as plaster board 17 18 Detaching the dome cover Important e After removal retain the dome cover fixing screw so as not t
16. cts on human health and the environment which could otherwise arise from inappro priate waste handling Please contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further infor mation Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal For U S and Canada Panasonic System Networks Company of America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2011 Ns021 1 0 For Europe and other countries Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg F R Germany STRO06874AZA Printed in China
17. e place in your particu lar environment Make sure that the installation area is strong enough to hold the product such as a concrete ceiling Install the camera in the foundation area of the architecture or where sufficient strength is assured f a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced Avoid installing this product in the follow ing locations Location where it may get wet from rain or water splash Locations where a chemical agent is used Such as a swimming pool ocations subject to steam and oil smoke Such as a kitchen Locations near flamma ble gas or vapor Locations where radiation or x ray emis sions are produced Locations where corrosive gas is pro duced Locations where it may be dam aged by briny air such as seashores Locations where the temperature is not within 10 C to 50 C 14 F to 122 F e Locations subject to vibrations This prod uct is not designed for on vehicle use Avoid moist or dusty places to install this system Otherwise lifetime of the internal parts may be shortened Avoid installing the camera in a place with a high level of noise Installation near an air conditioner an air clean er a vending machine or the like causes noise Be sure to remove this product if it is not in use Keep the camera cable away from the lighting cable Failure to observe
18. e settings for each item in accordance with the conditions of the camera shooting area Refer to the operating instructions PDF for further information Setup menu list Setup item Description CAMERA ID This item specifies the camera title The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols and is displayed on the screen CAMERA Performs the camera operation settings SCENE1 SCENE2 Selects a scene file It is possible to register and save the settings as a scene file in case that it is necessary to change the settings such when shooting at night or on holidays ALC Selects the method of controlling the quantity of light SHUTTER Specifies the electronic shutter speed AGC Specifies gain adjustment SENS UP Specifies electronic sensitivity enhancement WHITE BAL Specifies white balance adjustment DNR Selects the level of the digital noise reduction function BW MODE Performs each setting regarding the black and white mode such as Switching between color and black and white images i VMD Performs settings regarding intelligent VMD Video Motion Detector such as motion detection and object abandonment removal detection SYSTEM Performs the settings regarding the camera system such as synchroni zation and privacy zone SYNC Specifies the synchronization type LENS Performs automatic adjustment
19. em ie ondes 33 Standard accessories eec ea ecd epe p teta ced pesci esie ter cech pet 35 Optional aCccessories uuu IR RIEN CREER ID 35 This product is a 1 3 type CCD color CCTV camera Connection of this product to a video monitor allows users to use this product as a monitoring camera This is a model with x2 varifocal lens Ceiling mount bracket are optional SUPER D5 super dynamic function Integration of SUPER D5 into the CCD and signal processing circuit has achieved approximately 128 times higher dynamic range as compared with conventional camera Thanks to the integration of the darkness compensation function a subject on which much illuminance difference exists resulting from bright and dark areas can be naturally displayed in an image Newly developed high resolution CCD The introduction of the newly developed CCD with 976 of horizontal pixels has led to the horizontal resolution of as high as 650 TV lines typ Auto back focus ABF function Moving the CCD inside the camera to an optimal position with the operation button of this unit or the setup menu allows users to automatically adjust the back focus The back focus is adjustable with the setup menu through the system controller option even after installation of this unit The auto back focus function also allows users to correct out of focus when changing between color and black and white images High sensitiv
20. g screw marker on the camera and turn the dome cover clockwise to secure it Reinstall the dome cover fixing screw Dome cover fixing screw M3 step screw Important e Attach the inner dome in accordance with the lens direction to not to change the lens direction e Check if the tabs of the inner dome are firmly fit Remove the cushioning pink sheet from the inside of the dome and the protection sheet from the outside of the dome Note Defocus may be caused by the reinstalled dome cover When using a system controller option adjust the back focus on the setup menu after attaching the dome cover rs Operating Instruc tions PDF When not using a system controller by using the ABF2 button back focus adjustment is avail able after attaching the dome cover The procedure for the use of the ABF2 button is as spec ified below CD Press the ABF2 button The ABF operation indicator will start blinking While the indicator is blinking for around 3 minutes attach the dome cover to the camera When the indicator changes to steady light back focus will be adjusted automatically After the back focus is adjusted the indicator will go out Do not aim the camera to objects continuously moving If the indicator blinks again after changing to steady light back focus adjustment may have failed In this case check the back focus on the LCD monitor To adjust the back focus again perform Step D to 3
21. ge aansprakelijke dat het product waarop deze verklaring betrekking heeft voldoet aan de volgende normen of andere normatieve documenten overeenkomstig de bepalingen van Richtlijnen 2006 95 EC en 2004 108 EC Vi erklaerer os eneansvarlige for at dette produkt som denne deklaration omhandler er i overensstemmelse med standarder eller andre normative dokumenter i folge bestemmelserne i direktivene 2006 95 EC og 2004 108 EC Vi deklarerar h rmed v rt fulla ansvar f r att den produkt till vilken denna deklaration h nvisar r i verensst mmelse med de standarder eller andra normativa dokument som framst lls i direktiv nr 2006 95 EC och 2004 108 EC IImoitamme yksinomaisella vastuullamme ett tuote jota t m ilmoitus koskee noudattaa seuraavia standardeja tai muita ohjeellisia asiakirjoja jotka noudattavat direktiivien 2006 95 EC ja 2004 108 EC s d ksi Vi erkl rer oss alene ansvarlige for at produktet som denne erkl ringen gjelder for er i overensstemmelse med f lgende normer eller andre normgivende dokumenter som f lger bestemmelsene i direktivene 2006 95 EC og 2004 108 EC Important safety instructions 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufac
22. ing screw hole and the double rib on the camera Protrusion Fixing screw hole Attachment mounting hook Single rib 20 Secure the camera to the camera attachment with the camera fixing screw Recommended tightening torque 0 78 N m 0 58 lbf ft Remove the inner dome from the main body Press the parts with the PUSH indication Remove the screw blue 1 position for transport protection with a Phillips screw driver Screw for transport protection blue 21 Adjust the camera Be sure to view the monitor for adjustment when the camera angle is adjusted Connect the monitor for adjustment e g a small LCD to the monitor output connector and adjust the camera angle When determining the camera angle repeat fine follow the adjusting procedure of D 2 and 3 shown below Tilt adjusting table Tilting lock screw Monitor output connector RCA Panning lock screw Panning table CD Loosen the panning lock screw and rotate the camera head horizontally to adjust panning and tighten the panning lock screw Loosen the tilting lock screws and rotate the camera head vertically to adjust tilting and tighten the tilting lock screws Rotate the tilt adjusting table and adjust the azimuth angle of the image Important The panning lock screw and the tilting lock screw shall be securely tightened Recommended tightening torque 0 59 N m 0 44 Ibf f
23. ins to disconnect the main power for all unit Nosotros declaramos bajo nuestra nica responsabilidad que el producto a que hace referencia esta declaraci n est conforme con las normas u otros documentos normativos siguiendo las estipulaciones de las directivas 2006 95 CE y 2004 108 CE FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY WARNING This apparatus must be earthed IMPORTANT The wires in this mains lead are coloured in accor dance with the following code Green and yellow Earth Blue Neutral Brown Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be con nected to the terminal in the plug which is marked with the letter N or coloured black The wire which is coloured brown must be con nected to the terminal in the plug which is marked with the letter L or coloured red Noi dichiariamo sotto nostra esclusiva responsabilit che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive 2006 95 CE e 2004 108 CE Wij verklaren als eni
24. ity achieved thanks to noise reduction function The introduction of low noise circuit design has achieved excellently high sensitivity resulting in the minimum illuminance of 0 1 Ix in the color mode and 0 01 Ix in the black and white mode Night monochrome image activation function No operation is required at night because the image automatically changes from the color mode to the black and white mode at low illuminance Intelligent VMD i VMD functions of motion detection and object abandonment removal detection The motion and abandonment removal of an object are detectable The states of covering the camera with a cloth a cap or others and changing the camera direction notably can be detected Scene change detection The detection resolution has been significantly improved as compared with a conventional type and the introduction of the newly developed detection method has improved detection accuracy under the condition that the motion detection is prone to malfunction due to leaves swaying Note The i VMD function is not the dedicated function to prevent thefts fires etc We are not responsible for any accidents or damages occurring in case About the user manuals There are 2 sets of operating instructions for the WV CF504 NTSC model WV CF504E PAL model as follows nstallation Guide Explains how to install and connect devices Operating Instructions PDF Explains how to perform the settings and how to operate this c
25. n Screen transition diagram Top screen MODEL _ WV CF504 CAMERA ID OFF CAMERA SYSTEM BACK FOCUS t SPECIAL LANGUAGE CAMERA ID screen CAMERA ID 0123456789 ABCDEFGHIJKLM NOPORSTUVWXYZ ip amp dl SPACE POSI RET TOP END RESET END SETUP DISABLE CAMERA SETUP screen CAMERA SETUP SCENE1 ALC SHUTTER AGC SENS UP WHITE BAL DNR BW MODE i VMD RET TOP END OFF ON HIGH OFF ATWIY HIGH AUTOI SYSTEM SETUP screen SYSTEM SETUP SYNC LENS PRIVACY ZONE STABILIZER EL ZOOM UPSIDE DOWN RET TOP END INT PANASONIC OFF OFF OFF OFF BACK FOCUS SETUP screen BACK FOCUS SETUP ABF MANUAL ADJ C Le B W PUSH SW AUTO SETUP SW LOCK OFF NEAR FAR INDICATOR XXXX RET TOP END SPECIAL SETUP screen SPECIAL SETUP CHROMA GAIN AP GAIN PEDESTAL HUE PIX CAMERA RESET PUSH SW SER NO XXXXXXXX RET TOP END LANGUAGE SETUP screen LANGUAGE SETUP LANGUAGE SET RET TOP END ENGLISH 31 32 Troubleshooting Before asking for repairs check the symptoms with the following table Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below s Reference Symptom Cause solution pages Are the power cord and coaxial cable connected appropriately Check whether the connection is a
26. ntal 35 6 TELE 73 6 WIDE Vertical 26 6 TELE 53 4 WIDE Panning range 170 Tilting range 75 Azimuth range 100 Dimensions and mass indicated are approximate Specifications are subject to change without notice 34 Standard accessories CD ROM Yn ee eas 1 pc Installation Guide this book 1 pc Warranty Gard ios sessi ener b e dade 1 pc 1 The CD ROM contains the operating instructions PDF 2 NTSC model only The following parts are used during installation procedures Camera attachment sss 1 pc Optional accessories Dome cover WV CW4S Ceiling mount bracket WV Q175 Ceiling mount bracket WV Q105 1 PAL model only Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product Disposing of this product correctly will help to save valuable resources and prevent any potential negative effe
27. o lose The screw is required when attaching the dome cover Page 24 Remove the cover film from the dome section of the dome cover after the installation is com plete Do not touch the dome section by hand directly after removing the cover film Remove the dome cover fixing screw step screw x1 p 4 Dome cover fixing screw step screw Adjust the fixing screw marker on the cam era to I on the dome cover and turn the dome cover counterclockwise to remove it Fixing screw marker Using the side cable access hole When installing the camera directly on the ceiling or wall with cables exposed cut out a portion of the dome cover to open a cable access hole Side cable access hole ac us The above procedure is also required when mounting the camera using the ceiling mount bracket WV Q175 option 19 Camera installation Mount the camera To mount the camera on a two gang junction box or wall ceiling gt a Connect the power cord and the video output cable rs page 26 b Align the single rib on the camera with the protrusion on the camera attachment c Engage the camera s attachment mounting hooks with the mounting holes on the camera attachment and then rotate the camera in the direction of the arrow to secure the camera to the camera attachment without any backlash Note When the camera is secured the camera attachment protrusion is aligned with the camera fix
28. ock knob We s el Z Panning lock screw J left and right LOCK Tilt adjusting table Camera fixing screw Tilting lock screws 13 14 Video output cable Right button RIGHT FAR Moves the cursor to the right selects the 2 Power cord mode and adjusts some levels 3 Dome cover Inner dome Panning table Rotate this table to adjust the panning angle of the camera 5 Monitor output connector Connects the monitor for adjustment to this output connector Tilting lock screws left and right Fixes the tilting position Tilt adjusting table Adjusts the azimuth angle of the image Camera fixing screw Fixes the attachment on the camera body Panning lock screw LOCK Fixes the panning table Zoom lock knob Locks the zoom point Focus lock knob Locks the focal point 12 operation indicator Indicates the status of ABF operation 13 Setting button SET ABF2 MENU Confirms the setting contents Down button DOWN ABF1 Moves the cursor downward and selects items in the setup menu 15 Up button UP Moves the cursor upward and selects items in the setup menu Left button LEFT NEAR Moves the cursor to the left selects the mode and adjusts some levels When installing the camera on a wall or a ceiling there are four methods as specified below rs Pages 16 and 17 Using the two gang junction box nstalling the camera direc
29. ppropriately established s the adjusting monitor connected Check whether connection is estab 22 lished 3 Is the monitor brightness appropriately No imege gt adjusted or is the contrast appropriately adjusted Check whether the monitor settings are appropriate Were the shock absorbers in the dome cover already removed Confirm whether the shock absorbers have been already removed s the dome cover free from contamina tion and or flaws Check the dome cover s the focus adjusted correctly Check if the focus is adjusted correct 23 ly s the lens of the camera soiled with dirt or dust Check whether the lens of the camera is clean Blurred image gt Damaged power cord sheathing The power cord and connector is dam aged Use of the damaged cord or con p nector may cause electric shock or fire _ Heated portion of power line consisting of power cord during use Turn off the power immediately and request Warmed power cord or loos repair to your dealer ened connection by bending or stretching during use Specifications Basic Power source Power consumption Ambient operating temperature Ambient operating humidity Video output Dimensions Mass Finish Camera Image sensor Effective pixels Scanning area Scanning system Scanning frequency
30. ripheral devices Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment For U S A The model number and serial number of this product may be found on the surface of the unit You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006 95 EC and 2004 108 EC Wir erkl ren in alleiniger Verantwortung da das Produkt auf das sich diese Erkl rung bezieht mit den folgenden Normen oder normativen Dokumenten bereinstimmt Gem den Bestimmungen der Richtlinie 2006 95 EC und 2004 108 EC CAUTION An ALL POLE MAINS SWITCH with a contact Separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building Nous d clarons sous notre propre responsabilit que le produit auquel se r f re la pr sente d claration est conforme aux normes sp cifi es ou tout autre document normatif conform ment aux dispositions des directives 2006 95 CE et 2004 108 CE Turn the power off at the ma
31. t Note The video output to the BNC connector will be interrupted while an adjusting monitor is con nected to the monitor output connector At the same time for the pan and tilt adjustments make focus adjustments of Step 2 22 Adjusts the focus Focus adjustment shall be performed when camera angle adjustment are performed Adjust the focus by following the adjusting pro cedure of Q and 3 shown below CD Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appropriate angle of view and then tighten the zoom lock knob Loosen the focus lock knob make coarse adjustment of the focus and then tighten the focus lock knob Perform major adjustment of back focus through the setup menu or perform major adjustment by following Steps 3 and 4 below s Operating Instructions PDF Focus lock knob Note Reset the back focus position to the CS mount default position before the back focus adjust ment Hold down the right and left buttons simultaneously for 2 seconds or more or move the cursor to MANUAL ADJ of BACK FOCUS SETUP in the setup menu and press the right and left buttons simultaneously for 2 seconds or more after pressing the setting button Press the ABF1 button after adjusting the view angle while viewing the monitor for adjustment The operation indicator rs page 13 lights the focus position is displayed in the lower part of the screen
32. this may cause noise Radio interference When the camera is used near TV radio anten na strong electric field or magnetic field near a motor or a transformer images may be dis torted and noise sound may be produced In such a case run the camera cable through specialized steel conduit tubes Locally procure the screws Screws are not supplied with this product Pre pare the screws according to the material structure strength and other factors of the 11 12 mounting area and the total weight of objects to be mounted Screw tightening The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area Do not use an impact driver Failure to observe this may cause overtightening and consequently damage to the screws When a screw is tightened make the Screw at a right angle to the surface After tightening the screws or bolts perform visual check to ensure tightening is enough and there is no backlash Major operating controls and their functions 0 Video output cable Inner dome 3 Dome cover Up button UP Down button DOWN ABF1 Left button Setting button SET LEFT NEAR ABF2 MENU Right button 12 operation RIGHT FAR indicator This illustration shows the camera S without the inner dome TE m p A 10 Focus lock knob Zoom l
33. tly on the ceiling or wall e Using the ceiling mount bracket WV Q175 option for embedded installation on a ceiling e Using the ceiling mount bracket WV Q105 option for direct mounting on a ceiling Important Procure 4 screws M4 to secure the camera to a wall or a ceiling according to the material of the installation area In this case wood screws and nails should not be used For mounting a camera on a concrete wall use an anchor bolt for M4 or an AY plug bolt M4 for securing Recommended tightening torque 1 6 N m 1 18 Ibf ft e Required pull out capacity of a single screw bolt is 196 N 44 lbf or more f a ceiling board such as plaster board is too weak to support the total weight the area shall be sufficiently reinforced or the ceiling mount bracket for the camera WV Q105 option must be used The mounting conditions of the camera are described as follows Installation Applicable mount Recommended Number of Minimum pull out place bracket Screw screw strength per 1 pc Ceiling wall Two gang junction 4 4 pcs 196 N 44 lbf box Ceiling wall Direct mounting MA 4 pcs 196 N 44 Ibf Ceiling WV Q175 approx 700 g 1 55 Ibs Ceiling WV Q105 approx 12 150 0 33 Ibs 1 PAL model only 2 Make sure that the installed mount bracket can support more than 5 times of the weight of the camera 15 Method of camera installation Using the two gang junction
34. turer s instruc tions 8 Do not install near any heat sources such as radiators heat registers stoves or other appara tus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Limitation of liability
35. y or damage to the product Turn the power off immediately and contact qualified service personnel for service Select an installation area that can sup port the total weight Selecting an inappropriate installation surface may cause the product to fall down or topple over resulting in injury Installation work shall be started after sufficient reinforcement Periodic inspections shall be conducted Rust on the metal parts or screws may cause the product to fall down resulting in injury or accidents Consult the dealer for the inspections This product shall be installed in a vibra tion free place Failure to observe this may cause screws and bolts to be loosened and consequently to fall resulting in injury Install this product high enough to ensure that people don t hit their heads Failure to observe this may cause a drop result ing in injury or accidents Do not strike or give a strong shock to this product Failure to observe this may cause injury or fire Turn the power off when do wiring of this product Failure to observe this may cause electric shock A short circuit or wrong wiring may cause fire Do not use this product in an atmosphere of flammable gases Failure to observe this may cause injury by explosion Avoid installing this product in locations where it is subject to damage by salt or corrosive gas Otherwise the mounting fixtures will deteriorate causing the product to fall down and le
Download Pdf Manuals
Related Search