Panasonic PLCD24HD Operating Instructions
Contents
1. du mat riel et tre facile d acc s CAUTION TO SERVICE PERSONNEL POWER SUPPLY CORD I5 USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard do not expose the unit to rain or moisture v This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising v Do not cover the unit or place anything on the top of unit AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will v v shine directly on the monitor BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord v Damage to a power cord can cause fire or electrical shock INSTRUCTION MANUAL iaip ai Rede i a D i kj 4 FCC RF INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide2. connected securely into wall outlet or grounded extension cable or strip 2 Power switch should be in the OIM position and LED is lit Check that the Brightness and or the Contrast adjustments of the Display have not been turned down to minimum levels Going to Sleep The signal cable should be completely message on screen connected to the video card computer The video card should be completely seated in its slot and the computer is switched ON Display image is not Push the down key in front side or centered too small or Auto key in remocon too large in PC mode Vertical or Horizontal noise Adjust Clock and Phase in the OSD is present in the picture WEEE Symbols Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recyc
3. reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only shielded interface cable should be used Finally any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment gt DOC COMPLIANCE NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications ee PE r INSTRUCTION MANUAL CONNECTING WITH EXTERNAL EGUIPMENT A BOTTO
4. to select the Picture Sound 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select the Picture Mode 4 Press the right gt or ENTER button and then press up 4 down v button to select the desire Picture Mode 5 Press the MENU button to save anas maces tee serine O basa aa P E INSTRUCTION MANUAL CONTROLS AND FUNCTIONS Picture Sound Ficture Mode Color Tone Red R Green G Blue B Muta Volume Menu 1 Press the up 4 down v button to select the Color Tone 2 Press the gt or ENTER button and then up 4 down v button to select the desired color tone Custom cool Normal Warm factore setting is Custom 3 Press left right gt button to adjust color setting of RED Green Blue only custom mode other color tone are factory setting value 4 Press the MENU button to save 3 PC control Only PC mode Picture Sound Picture Sound Picture Mode Custom Color Tone Custom g Phase Muta Off a H Position Volume 20 M Position Frequency Menu love B Enter Menu 1 Press the up 4 down v button to select the PC 2 Press the gt or ENTER button 3 Press the up 4 down v button to select PC sub menu 4 Press the right gt or ENTER button and then left right gt button to adjust PC setting 5 Press the MENU button to save Auto Adjust Auto geometry adjustment Phase Adjust t
5. M PANEL CONTROL e Oo 1 AC POWER 2 Y Pb Pr 8 SOUND L R 3 AUDIO OUT 4 PC STEREO IN 5 D SUB IN 6 DVI IN 7 HDMI IN B SIDE PANEL CONTROL 1 VIDEO 1 AV1 IN 2 VIDEO 1 AV1 OUT 3 VIDEO 2 AV2 IN 4 VIDEO 2 AV2 OUT 5 S VIDEO Y C IN 6 S VIDEO Y C OUT 7 AV1 S VIDEO AUDIO IN 00000000 00000000 O O 8 AV1 S VIDEO AUDIO OUT 9 AV2 AUDIO IN 10 AV2 AUDIO OUT INSTRUCTION MANUAL r iai a a o a a 6 REMOTE FUNCTIONS C REMOTE CONTROLLER 1 POWER Turns the power ON or OFF There will be a few seconds delay before the display appears 2 SOURCE Select pc or video AV1 AV2 S Video DVI PC sources 3 AUTO Auto geometry adjustment in PC Source 4 MUTE Mute the sound 5 MENU Activates and exits the On Screen Display 6 EXIT Exit the On Screen Display 7 VOL 4 Increases or decreases the level of audio volume 8 UPIDOWN Move to OSD menu 9 ENTER Accepts your selection or displays the current mode 10 INFO Input mode information Display 11 STILL Pause the picture 12 PIP Picture In Picture Activates PIP mode 13 P INPUT Select PC or video source 14 P POS Move the position of sub picture for PIP mode 15 P SIZE Change the size of sub and main picture for PIP mode 16 SWAP Alternates between main and sub picture 17 ARC Aspect Ratio Control Select scre
6. PLCD24HD 24 INCH PREMIUM TFT LCD MONITOR INSTRUCTION MANUAL Please read this manual thoroughly before use and keep it handy for future reference CONTENTS SARE IY INST RUG TIO Nissi nitidum i i a vedo 2 3 important a ii ecole eaten le 2 3 Que cc esi i ai i a 4 FCC RF INTERFERENCE STATEMENT Ie e nennen aaa aaa 5 CONNECTING WITH EXTERNAL 2 6 REMOTE FUNC TONS ia a ii a as 7 CONTROLS AND FU NGTIONS ii SERE coke o dnt 8 21 GD E NC er PI 22 D SUB CONNECTOR PIN ASSIGNMENTS 0000 23 POWER MANAGEMENT as eor Ep a obe 24 SPECIFICATIONS IU I IU C AME Diu t 25 TROUBLESHOOTING GUIDE 26 This Monitor was Manufactured by ISO 8001 Certified Factory M M INSTRUCTION MANUAL SAFETY INSTRUCTION Important Safety Instructions 1 Read these instructions 2 Keep these instructions 6 warnings A Do not use this apparatus near water O Follow all instructions Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the mauf
7. acturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the prong A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safely If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avid injury from tip over My 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped INSTRUCTION MANUAL
8. ce Component HDMI DVI PC 3 Press the MENU button to save 3 Size PIP On PIP On Input Source Component Position Input Source Component Position Swap Swap Sound Select Sound Select Main Menu Adjust 4 Select 1 Press the up 4 down v button to select the Size 2 Press the right gt or ENTER button and then press up 4 down v button to select the desire Size 3 Press the MENU button to save aa TT Ta INSTRUCTION MANUAL CONTROLS AND FUNCTIONS 4 Position PIP On PIP Input Source Component Size E Input Source Size Swap Swap Sound Select Main Sound Select Menu Menu 1 Press the up 4 down v button to select the Position 2 Press the right gt or ENTER button and then press up 4 down v button to select the desire Position 3 Press the MENU button to save 5 Swap PIP On Input Source Component Size Position Sound Select 1 Press the up 4 down v button to select the Swap 2 Press the right gt or ENTER button INSTRUCTION MANUAL Drop UP VK P 17 CONTROLS AND FUNCTIONS PIP On PIP On Input Source Component Input Source Component Size E Size gp Cul Position Position Swap Swap Sub 1 Press the up 4 down v button to select the Sound Select 2 Press the right gt or ENTER button and then pres
9. e 5 Press the MENU button to save 2 Color Tone Picture Sound Picture Mode Standard Picture Sound Picture Mode Standard Muta Muta Volume Volume Size Size NR 3D Comb E Enter Menu 1 Press the up 4 down v button to select the Color Tone 2 Press the gt or ENTER button and then up 4 down v button to select the desired color tone 3 Press the MENU button to save INSTRUCTION MANGAL sisiuks i i i 10 CONTROLS AND FUNCTIONS 3 Mute Picture Sound Picture Sound 2 Ficture Made Standard B Ficture Moda Standard Color Tone Normal Color Tone Normal m Cn Volume Volume Size Size 2D Comb E Enter 4k Select Menu 1 Press the up 4 down v button to select the Mute 2 Press the gt or ENTER button and then up 4 down v button to select the desired Mute 3 Press the MENU button to save 4 Volume Picture Mode Standard Color Tone Hormal Muta Size HR Adjust 1 Press the up 4 down v button to select the Volume 2 Press 4 right gt button to adjust Volume 3 Press the MENU button to save aisiais ai si asa D i D O p INSTRUCTION MANUAL CONTROLS AND FUNCTIONS 5 Size Only Video mode Picture Sound Picture Sound P Ficture Mode Color Tone Muta Picture Mode Standard Color Tone Muta O
10. en ratio 18 APC Auto Picture Control Select picture mode 19 ACC Auto Color Control Select Colour mode 20 S SET Select Sound mode main input or sub input 21 PC Select PC mode PC DVI 22 AV Select AV mode AV1 AV2 S VIDEO 23 COMP Select COMPONENT mode a ai Misa a aa E ETE INSTRUCTION MANUAL CONTROLS AND FUNCTIONS D FRONT KEY CONTROL MENU 4 Y sec exit 0000000 00 1 MENU Activates and exits the On Screen Display 2 SOURCE Select PC or video source Select On Screen Display menu 3 4 v 4 This button allows user to enter the sub menu of the activated function 5 6 VOL Adjust the volume Adjust menu settings 7 POWER ON OFF 9 Turns the power ON OFF There will be few seconds delay before the display appears 8 IR Sensor Remote controller sensor 9 POWER LED The power LED next to the power switch lights with green when the power is turned ON The power is turned off by pressing the power switch again and the power LED goes Red INSTRUCTION MANUAL ii siai i i o a a i i i i NO i i SURE E 8 CONTROLS AND FUNCTIONS OSD MENU DESCRIPTION A CUSTOM MENU Only Video mode Brightness Contrast Color Tint Contrast Color Tint Sharpness Sharpness Brighiness Menu 4b Adjust Menu 1 Press the MENU button and then up 4 down v button to select the Custom menu 2 Press the up 4 do
11. ff Volume 20 Volume HR B Enter Menu Menu 1 Press the up 4 down v button to select the Size 2 Press the gt or ENTER button and then up 4 down v button to select the desired Size 3 Press the MENU button to save 6 NR Picture Sound Picture Sound Ficture Made Standard Picture Mode Standard Color Tone Muta Off Color Tone Normal Muta Volume Volume Size 3D Comb E Enter Menu 1 Press the up 4 down v button to select the NR 2 Press the gt or ENTER button and then up 4 down v button to select on or off 3 Press the MENU button to save INSTRUCTION siai is ai asi otas a o i i a a i i a i a 12 CONTROLS AND FUNCTIONS 7 3D Comb Picture Sound Picture Sound Picture Mode Standard b F Picture Mode Standard Color Tone Normal Color Tone Normal Muta 1 F Muta n Volume 20 Volume Size 4 3 Size NR Off B Enter Menu Pus Menu 1 Press the up 4 down v button to select the 3D Comb 2 Press the gt or ENTER button and then up 4 down v button to select On or Off 3 Press the MENU button to save B Picture Sound Menu Only PC mode 1 Picture Mode Picture Sound Color Tone Muta Picture Sound Color Tone Muta Volume Volume PG Menu Menu 1 Press the MENU button and then up 4 down v button
12. he number of horizontal picture elements H position Move image horizontally on screen right or left V position Move image vertically on screen up or down Frequency Adjust the vertical noise of screen image INSTRUCTION 0 0 0 000000000000 06 5 hse eene eene 14 CONTROLS AND FUNCTIONS C PIP MENU Only Video mode PIP On Input Source Component Sia Position Swap Sound Select Main Enter Manu Press the MENU button and then up 4 down v button to select the PIP menu Press the right gt or ENTER button 1 PIP Input Source Component Size La Posilion Swap Input Source Size Position Swap Sound Select Main Sound Select LIN Enter Menu 1 Press the up 4 down v button to select the PIP 2 Press the right gt or ENTER button and then press up 4 down v button to select the On orOff 3 Press the MENU button to save gt gt NOTE When a Input Relution is 1920 x1200 or 1920x1080i P PIP Funtion isn t activated i i INSTRUCTION MANUAL CONTROLS AND FUNCTIONS 2 Input Source Only Video mode Size Size Position Position Swap r Swap Sound Select Main Sound Select Menu T dF Select Menu 1 Press the up 4 down v button to select the Input Source 2 Press the right gt or ENTER button and then press up 4 down v button to select the desire Input Sour
13. ling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal INSTRUCTION MANUAL P N L39ME0151
14. n blanks after preset idle time RED ON OFF d son SUSPEND 1 SEC And some electronic circuits or all Circuitry in the monitor shut down ACTIV OFF ircuitry i ut dow UNSUPPORTES GREEN Normal operation but the on screen MODE Display will show error massage POWER OFF Not Operation Ed TT INSTRUCTION MANUAL SPECIFICATIONS 24 0 Diagonal AM TFT Active Matrix Pixel M 0 270 H x 0 270 V LCD Type BRIGHTNESS 400cd JM CONTRAST RATIO 1000 177 VIEWING ANGLE 160 160 RESPONSE TIME E ui E ui x V 1920X1200 000000000000 HORIZONTAL 31 80KHz RE E VERTICAL 56 75Hz VIDEO 2ch input 1 0Vp p 750 terminated loop through out er input Y C ECC CNN out ECT MN Pb Pr Sound L R INPUT SIGNAL DVI ELATI MEME Video Interface Definition Multimedia Interface RGB souna wout Sound in Out 4 Stereo Audio Audio Out Speaker Out Out ACTIVE DISPLAY AREA W x H 518 4 mm x 324 0 mm PACKING 650mm X 205mm X545 mm 25 59 X 8 07 X21 45 DIMENSIONS W x D xH Net 9 0Kg WEIGHT Gross Gross Weight 12 069 12 0Kg poss gt gt NOTE Technical specifications are subject to change without notice INSTRUCTION 25 TROUBLESHOOTING GUIDE TROUBLE TROUBLESHOOTING TIP No image on display screen 1 Check that power cord of the Monitor have been
15. nel to install the LCD monitor to the wall Wall mount Installation 1 The Monitor fixing bracket to the monitor using the fixing screws provided 2 he monitor fixing bracket assembled with monitor T Be f m V a T V Be o B T We E J WALL D INSTRUCTION MANUAL D SUB CONNECTOR PIN ASSIGNMENTS PIN ASSIGNMENTS RED VIDEO GROUND GROUND 3 H SYNC or H V SYNC RED GROUND ACCESSORY L gt 1 User s Manual 2 Power Cord 3 Remote Control Unit And Battery 4 VGA Cable INSTRUCTION MANUBL uv i i a i i a i i ERU 23 POWER MANAGEMENT This monitor features a power management system to power down upon receipt of the VESA DPMS The display power management signaling from a VESA DPMS video card VESA DPMS compliant video card performs this signaling system through not sending horizontal vertical or sync signal This monitor enters an appropriate mode through identifying each of the three modes of the signaling system POWER CONSUMPTION 110W LED INDICATOR The power management feature of the monitor is comprised of four stages On Green Standby Suspend Active off Red on off 1 sec and Unsupported mode Green MODE LED COLOR MONITOR OPERATION GREEN Normal Operation ZENOB Scree
16. p 4 down v button to select the Language menu 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select language 4 Press the MENU button to save 3 OSD Tone Reset Reset Language English Language English Transparency Blue Screen Off Blue Screen Key Lock Off Key Lock Off 1 Press the up 4 down v button to select the OSD tone menu 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select the OSD tone menu 4 Press the MENU button to save 1 PPP scam beaoee sees INSTRUCTION MANUAL CONTROLS AND FUNCTIONS 4 Blue Screen Reset Reset Language Language OSD Tone OSD Tone Key Lock Key Lock Menu Menu 1 Press the up 4 down v button to select the blue screen 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select on or off 4 Press the MENU button to save 5 Key Lock Reset Reset Language OSD Tone Language OSD Tone Blue Screen Blue Screen Menu 1 Press the up 4 down v button to select the key lock menu 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select on or off 4 Press the MENU button to save INSTRUCTION MANUAL hx VrbEEVEEFCEVRONHEFERTEREFEEREPRF Fr ERE Ra rset PEE E E ben 21 MOUNTING GUIDE Using the VESA standard wall mount design and the 100mm hole pattern on the back pa
17. s up 4 down v button to select the desire Sound Select 3 Press the MENU button to save C PIP MENU Only PC mode 1 Input Source PC mode PIP PIP Siza Size o Position Swap Swap S d Select oun Sound Select 1 Press the up 4 down v button to select the Input Source 2 Press the right gt or ENTER button and then press up 4 down v button to select the desire Input Source AV1 AV2 S VIDEO 3 Press the MENU button to save gt gt NOTE When a Input Relution is 1920 x1200 or 1920x1080i P PIP Funtion isn t activated 18 e INSTRUCTION MANUAL CONTROLS AND FUNCTIONS D SETUP MENU Reset Language English OSD Tone Blue Blue Screen Off Key Lock Off Press the MENU button and then up 4 down v button to select the Setup menu Press the right gt or ENTER button 1 Reset Language Language OSD Tone OSD Tone Blue Screen Of Blue Screen Key Lock O p Key Lock Menu 1 Press ENTER button to select the reset Reset Select to reset all setting to the factory default values 55 5 FUE 19 CONTROLS AND FUNCTIONS 2 Language Reset Reset Francais OSD Tone OSD Tone Deutsch Blue Screen Blue Screen Italiano Key Lock Key Lock Espanol Portugu s Nederland Menu 1 Press the u
18. si sa ek a a i a ter 2 SAFETY INSTRUCTION The apparatus shall not be exposed to dripping or splashing and that no objects filled with liguids such as vases shall be placed on the apparatus Minimum distances e g 10cm around the apparatus for sufficient ventilation WARNING To reduce the risk of fire or electric shock do not expose the apparatus to rain or moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance v rr INSTRUCTION MANUAL CAUTIONS CAUTION The power supply cord is used as the main disconnect device ensure that the socket outlet is located installed near the equipment and is easily accessible ATTENTION Le cordon d alimentation est utills comme interrupteur g n ral La prise de courant doit tre situ e ou install e proximit
19. wn v button to select Custom sub menu Press the left lt right gt button to adjust picture setting Press the MENU button to save Brightness Increase or decrease the intensity of the image Contrast Increase or decrease the intensity lightness or dimness of the image Color Increase or decrease the colour of the picture Tint Increase or decrease the tint of the picture Sharpness Increase or decrease the sharpness of the picture A CUSTOM MENU Only PC mode Brightness Contrast Contrast Brightness 4 4 gt Adjust Menu Menu 1 Press the MENU button and then up 4 down v button to select the Custom menu 2 Press the up 4 down v button to select Custom sub menu Press 4 right gt button to adjust picture setting Press the MENU button to save INSTRUCTION MANUAL CONTROLS AND FUNCTIONS B Picture Sound Menu Only Video mode 1 Picture Mode Picture Sound Picture Sound Color Tone Color Tone Muta Muta Volume 0 Volume Size 4 3 HR Comb Size HR Menu 1 Press the MENU button and then up 4 down v button to select the Picture Sound 2 Press the right gt or ENTER button 3 Press the up 4 down v button to select the Picture Mode 4 Press the right gt or ENTER button and then press up 4 down v button to select the desire Picture Mod
Download Pdf Manuals
Related Search