Panasonic AG-MX70 Menu Information
Contents
1. setting is 20 dB for NTSC and 18 dB for PAL 4dB File setting The statuses set by Setup can be stored in the memory E Re ES ne Rs Select 1 to 8 using the rotary 2 control An empty file is Empty indicated by Empty A file with settings is indicated by Saved Saved Select Save Recall or AlICLR using the rotary 3 control and execute using Enter Save saves the settings and overwrites any existing settings Recall loads the settings and All CLR clears the settings When Save or AIICLR is selected OK appears Enter the selection again using Enter or cancel using Shift Enter It is also possible to clear all the settings by holding down Shift Enter when the power is turned on so that the factory settings are restored 57 Other settings Event memory Setting method Event 00E One hundred panel statuses can be stored in event memories 0 to 99 Press the Set button set the event number using the number keys and enter the setting using Enter Set button Its lamp lights during the setting process When Enter is pressed it flashes for two seconds and then goes off When the setting is in progress Event is displayed in reverse video and the event is then entered using Enter Event numbers can be incremented and decremented using the and keys Empty events are indicated by E appearing next to the event number Recall method Pr2. The Type Audio Tally On initiate Still or Off do not initiate Still when cross A i AB On CP 8 points are to be changed is selected using the rotary 3 control The default setting is On The Audio MIX system can be selected using the rotary 4 control At the CP setting two audio sources allocated to the selected cross point are output At the 1 2 setting the audio sources 1 2 allocated to the cross point are mixed at all times The default setting is CP 8 or EXT can be selected using the rotary 5 control as the setting for the eight tally outputs At the 8 setting the tally signal is output when cross point 8 has been selected at the EXT setting it is output when EXT has been selected Prg Pre Off 1 2 EXT lt Note gt When Still has been set to Off the picture may be disturbed if direct switching is performed between SDl composite and YC component This setting must always be used with either an SDI only composite system or YC only component only system 56 Setup initial setting screen Audio Level setting The Alignment alignment level is set using the rotary 2 R1 R2 R3 R4 R5 control 3 dB 0 dB or 4 dB can be selected The Audio Alignment Head default setting is 4 dB for NTSC and 0 dB for PAL Level 3dB 18dB The Head headroom is set using the rotary 5 control Either 18 dB or 20 dB can be selected The default lt b r
3. The default setting is 4 3 Select 0 or 7 5 for Setup using the rotary 4 control The default setting is 0 Select BCAM or MI for the Pb Pr component level using the rotary 5 control The default setting is BCAM When the NTSC or PAL format is changed the system is initialized and the INT V and title memories are cleared system was purchased led 16 9 7 5 MI NSTC ie BCAM 55 Setup initial setting screen System1 setting This is used to perform a variety of settings RE de ES RS The rotary 2 control is used to set the amount of delay for System1 Dly Time RS422 the source input when the AdvRef advanced reference 1Frame Sec GVG ignal i t ith the 3D optional AG VE7 signa is connected wi e 3D op iona board AG 0 TFrame See ME GvG installed If OFrame is selected the video delay amount is OFrame Frame DSK SONY different between when the 3D effects are applied and when Fade they are not The default setting is 1Frame The setting is fixed at OFrame when the 3D optional board is not installed The audio source delay amount is also set according to this setting Sec Seconds frames or Frame frames only is selected for the time display using the rotary 3 control The default setting is Sec Whether ME DSK or Fade is to be executed by GPI can be set using the rotary 4 control The default setting is ME GVG or SONY can be selec
4. 4xxx and 5xxx as well as key learn patterns 9000 to 9019 can be assigned to direct key pattern buttons Transition patterns Oxxx 1xxx and 2xxx can be assigned to direct key transition buttons The factory settings are the patterns displayed 53 Setup initial setting screen Audio Video Input settings These are used to set the audio and video inputs R1 R2 R3 R4 R5 When Setup is selected using the rotary 2 control and A l Audio Enter is pressed OK appears so press Enter to change Video to the setting mode Use Shift Enter to cancel When Default is selected using the rotary 2 control and Enter is pressed OK appears so press Enter to change to the default setting When V Link is selected using the rotary 2 control and Enter is pressed OK appears so press Enter to change operation so that the audio input is matched with the video input Factory settings Event ME Time Pattern INT 00e 10 00F 3015 Wht Audio Video Input Setup 7 Enter to EXIT 1 vss Video A S 1 Analog 2 V S 2 Video A S 2 Analog 3 V S 3 Video A S 3 Analog _ 4 V S 4 Video A S 4 Analog 5 VS 5 Video A S 1 Analog 6 V S 6 Video A S 2 Analog 7 V S 7 Video A S 3 Analog 8 V S 8 Video A S 4 Analog AUXin Mic R1 R2 R3 R4 R5 Setting method Press the button of the cross point to be set Alternatively select the button of the cross point which is to
5. and T sl a how much for Title for DSK and TitleKey is set using the 0 30 26 0 30 26 rotary 2 and 3 controls If the allocation to one memory is changed the allocation to the other memory will change so that the total remains 30 When a change is to be made OK appears Execute the change using Enter and use Shift Enter to cancel The default setting is 15 each for INT V and Title with NTSC and 13 each for INT V and Title with PAL Gen Lock external synchronization setting Select G L or ExtKey as the Ref In reference source using the rotary 2 control The default setting is G L Ref e ah Phase SC Phase Adjust the H Phase horizontal phase using the rotary 3 D 128 512 control The default setting is 128 28 228 0 1023 Adjust the SC Phase subcarrier phase using the rotary 4 A F control The default setting is 512 ela H Phase and SC Phase are stored in the memory separately in accordance with G L or Ext Key for the input Video Format setting Either NTSC or PAL is selected as the format by the RI Ra R R4 HS rotary 2 control Video Aspect Pb Pr The default setting is the format used in the area where the Format NTSC 4 3 BCAM When a change is to be made OK appears Execute the change using Enter and use Shift Enter to cancel Set 4 3 or 16 9 as the Aspect ratio of the patterns using the rotary 3 control
6. be set using the rotary 1 control The lamp of the selected button flashes and the bus is automatically output to Preview When the cross point has been selected using the rotary 1 control the A bus is output to Preview Select V S 1 V S 2 V S 3 V S 4 V S 5 V S 6 V S 7 or V S 8 as the video input using the rotary 2 control Select Video composite YC Y Pb Pr component or SDI using the rotary 3 control Except for Video the sources extend from S 1 to S 4 so 5 is changed to 1 6 to 2 7 to 3 and 8 to 4 If the setting operation is exited part of the way through the settings performed so far will not be stored in the memory They are entered using Enter and operation returns to the Audio Video Input settings Select A S 1 A S 2 A S 3 or A S 4 as the audio input using the rotary 4 control Select ANALOG or SDI using the rotary 5 control Video input combinations that cannot be set S 5 to S 8 YC Y Pb Pr SDI Audio input combinations that cannot be set Combination of SDIs with different source numbers Example SDI of S 1 for video and SDI of S 2 for audio Mic or AUX2 can be set for AUXin using the rotary 4 control The default setting is Mic 54 Setup initial setting screen Memory setting This is used to set the memories used for INTVideo and a na ne R RS DSK When the setting is changed all the memories are Memory INT V Title cleared How much memory is to be used for INT V
7. CD screen settings In the event memories the number keys cannot be used for pattern settings transition time settings or LCD screen settings 59
8. Panasonic Broadcast AG MX70 Menu Information Setup initial setting screen Wash Pb128 Pr 128 i Y 196 I Event ME Time Pattern 00e 10 00F 3015 Setup Power Direct Pattern Audio Video Memory Title Scrolled display Gen Ref In H Phase SC Phase Lock G L 128 512 Video Aspect Setup Pb Pr Format NTSC 4 3 BCAM System1 Dly Time GPI RS422 1Frame Sec ME GVG System2 Lcd Stby VBClean DR Chr Lmt 0 Off On Off Bus Type Siill Audio Tally AB On CP Audio Alignment Head Level 4dB 20dB File Empty R1 R2 R3 R4 R5 Select the item to be set using the rotary 1 control Items consist of Power Direct Pattern Audio Video Memory Gen Lock Video Format System1 System2 Bus Audio Level and File The setup settings are not returned to the factory settings even if the system is started by Reset They can be restored to the factory settings by pressing Shift and Enter together when the power is turned on 51 Setup initial setting screen Power power ON setting Whether the system is to be started from the Reset status from the Preset status or in the Demo mode can be selected using the rotary 2 control With Reset the settings except for the event memories setup settings file memory and key learn settings are initialized With Preset the mode in which the sy
9. ess the Recall button select the event number to be loaded using the number keys and recall it using the Enter or AutoTake button Recall button Its lamp flashes while recall is underway It lights when the button is set to ON and goes off when it is set to OFF or when the recall is completed Since the input settings are not reflected during loading events are executed in respect of the input set beforehand Events 50 to 59 60 to 69 70 to 79 80 to 89 and 90 to 99 can be set consecutively in units of 10 events and also recalled consecutively so they can also serve as key frame settings Events are executed using the AutoTake button With the recall of events 50 to 99 the Setup status of the head event is valid Clearing events Set the number of the event to be cleared using Recall and execute clearing using Shift Enter Clearing all the events is possible by inputting a period twice at the recall stage and then pressing Shift Alternatively this can be achieved by starting the system by pressing Shift Enter when the power is turned on and restoring the factory settings Pattern settings Press the Pattern button input the pattern number using Pattern the number keys and execute using Enter If the pattern 301 5 does not exist operation will jump to the nearest pattern number Each time Pattern is pressed the function is set to ON or OFF The default setting is MIX 56 Pattern numbers are
10. incremented and decremented using the and keys Patterns that do not exist are skipped and displayed in turn 58 Other settings Transition time setting Select the item to be set and press the ME DSK or ME Time FADE button 1 0 00 Input the numerical value using the number keys and press E F Enter The numerical value can be incremented and decremented using rotary TIME or the and keys Set the ME back key transition DSK or fade time Set the time of the item selected for ME DSK or Fade above the number keys Alan The time is indicated on the LCD display It can also be JOTO input or output using the number keys Transition time selection With x xx displays it is possible to input 2 5 to display CONTRAST 2 05 where is used as a delimiter AN The default setting is 60F 00005 Correlation between number key settings and Pattern button Pattern takes precedence over ME DSK and Fade Items selected by ME DSK or Fade can be set by the rotary controls The number keys can also be used when Pattern is OFF The items selected appear on the LCD display There are three options ME DSK and Fade and they can be set to OFF by pressing the ON button In this case neither the rotary controls nor the number keys can be used Number key priorities The number key priorities are event memories pattern settings transition time settings L
11. irect pattern button 2 The lamp of the selected button flashes The Mix Chrm chroma key and Lum luminance key cannot be set 3 Use the number keys to input the pattern to be assigned The pattern is displayed in the pattern area The program output can be checked using the wipe lever 52 Setup initial setting screen The LCD display now shows the setting screens for each effect pattern Proceed to set the edges and effects and if the settings are acceptable enter them using Enter and return to the direct pattern settings Example of transition Pos X 128 Y 128 Z 196 Event ME Time Pattern INT 00e 10 00F 2001 Wht Direct Pattern Transition Enter to EXIT R1 R2 R3 R4 R5 If the setting operation is exited part of the way through by pressing other buttons etc the settings performed so far will not be stored in the memory The settings of six key patterns and seven transitions patterns are stored in the memory The edges and effects of each of the patterns are also stored Example of key pattern Pos X 128 Y 128 Z EM Z 196 EZ EI EM Event ME Time Pattern INT 00e 10 00F 6301 Wht Direct Pattern Key Enter to EXIT Color K Level White 255 ka gt 12 Light On TransF R1 R2 R3 R4 R5 Key patterns 3xxx
12. stem is started from the status prior to power OFF is established when the power is next turned on If no status prior to power OFF existed when for instance the system is used for the very first time after assembly or its memories have been destroyed the system is started from the factory setting status With Demo the system starts up in the demonstration mode when the power is next turned on This menu is displayed in the demonstration mode so that when the system is restarted by selecting Preset or Reset the regular operation screen will appear Alternatively when Enter is pressed the demonstration mode is suspended and operation is enabled To execute the demonstration mode again turn the power off and then back on again The audio faders can be used even in the demonstration mode The default setting is Preset Direct Pattern setting This is used to set the pattern which is to be called as the R1 R2 R3 R4 R5 direct pattern Direct When Setup is selected using the rotary 2 control and Pattern Enter is pressed OK appears so press Enter to change Setup to the setting mode Use Shift Enter to cancel Default When Default is selected using the rotary 2 control and Enter is pressed OK appears so press Enter to change to the default setting Use Shift Enter to cancel Setting method in the setting mode ME is selected for Preview so it can be used to check 1 Press the d
13. ted as the RS 422A protocol using the rotary 5 control The default setting is GVG System2 setting The time taken until the LCD is set to the power saving R1 R2 R3 R4 R5 mode can be selected using the rotary 2 control System2 LCDStby VBClean Chr Lmt With the 0 setting the display is always on The time can 0 Off Off 0 60 On On On be set in 10 minute increments from 0 to 60 The default setting is 0 On or Off is selected using the rotary 3 control to set whether or not cleaning is to be performed inside the vertical blanking period VBIk The default setting is Off On or Off is selected using the rotary 4 control to set whether or not the DR dynamic rounding is to be performed The default setting is On On or Off is selected using the rotary 5 control to set whether restrictions are to be applied to the SDI and component output chroma If On has been selected the chroma is restricted by the 100 color bar level The default setting is Off Off Off Off lt Note gt Selecting Off for VBClean may result in a deviation in the amount of delay between the video signals and vertical blanking signals depending on the setting for the Dly item among the System1 settings and on whether the 3D optional board AG VE70 has been installed Bus setting AB AB bus or PrgPre program preset system can be R1 Re RS na R3 selected as the bus system using the rotary 2 control
Download Pdf Manuals
Related Search