Palm TreoTM User's Manual
Contents
1. goes into standby mode When the headset is in standby mode the blue light flashes every 3 seconds 14 Treo Wireless Headset Product regulatory information Product regulatory information FCC This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which t2. supported by your phone Treo Wireless Headset 9 Modes and alerts Modes and alerts Your headset works in several different modes each with its own types of alerts Name Definition Indicator light Sounds Active mode When you are One long None currently on a call flash every 8 seconds Mute mode Turns your Flashes every Single tone headset s 8 seconds every 15 microphone off seconds when the microphone is off Standby When your One quick None mode headset is on but flash every 3 you are not seconds currently ona call Low battery Three to 5 minutes Two quick Five tones of talk time left flashes every every 20 5 seconds seconds Fully charged your headset offers up to 7 hours of call time in active mode When you are on a call quickly press the multifunction button lt gt twice to turn mute mode on or off Fully charged your headset offers up to 170 hours of standby mode 10 Treo Wireless Headset Enhanced features Enhanced features Enhanced features are available for phones that support the hands free Bluetooth profile meaning you can use your headset wirelessly with your phone for some features Check your phone s instruction guide or contact the phone manufacturer if you are not sure if your phone supports the hands free Bluetooth profile N NOTE The Treo 650 smartphone supports the hands free profile Redial the last number While the headset is in standby mode press and hold the mu
3. you use the headset for the first time Charge your headset for approximately 2 hours Keep the following in mind while charging your headset e Do not attempt to charge the headset with anything other than the AC charger provided Using another AC charger may damage or destroy the headset e Removing the charger from the headset during charging will put the headset into standby mode described later in this guide and stop the charging sequence e The headset cannot be used while being charged 2 Treo Wireless Headset Pairing with your Bluetooth phone N NOTE Your headset comes with an AC charger and plugs that are compatible with international outlets You can use the same charger for both your headset and your Treo 650 smartphone so you do not need to carry two chargers when you travel 1 Plug the AC charger into an electrical outlet and then into the headset s charging connector The blue indicator light remains lit while the headset is charging 2 Charge for 2 hours and then remove the AC charger from the headset The blue indicator light turns off when the headset is fully charged You are now ready to pair the headset with your mobile phone If the headset has already been paired with your phone then you can begin using it Pairing with your Bluetooth phone Pairing creates a unique and encrypted wireless link between two devices enabled with Bluetooth wireless technology such as your Bluetooth p
4. The Treo Wireless Headset by palmOne The Treo Wireless Headset by palmOne Thank you for purchasing the Treo Wireless Headset by palmOne We hope you will be delighted with its operation Please read this manual to get started and make the best use of your headset s many features IMPORTANT Using a mobile phone while driving creates a distraction to the driver and this may increase the likelihood of an accident When using the phone while driving keep conversations short and do not make notes or read documents Before answering calls consider your circumstances Pull off the road and park before making or answering calls when driving conditions require it for example bad weather high traffic density presence of children in the car or difficult junctions or maneuvers Always follow local laws What you ll learn to do in this manual e Charge your headset and turn it on e Check compatibility and pair with your Bluetooth phone e Choose a wearing preference e Make answer and end a call e Use call waiting e Use enhanced features M NOTE Read the glossary at the end of this document to familiarize yourself with important terms Treo Wireless Headset 1 Your headset Your headset Multifunction button with blue indicator light AL Volume control buttons Charging connector Charging your headset Your headset uses a rechargeable battery that must be charged fully before
5. d wireless networking equipment may cause interference adding a crackling noise To reduce interference keep the headset away from other devices that use or produce radio waves Will my headset interfere with my car s electronics radio or computer Your headset produces significantly less power than a typical mobile phone It also emits only signals that are in compliance with the international Bluetooth standard Therefore you should not expect any interference with standard consumer grade electronics equipment Can other Bluetooth phone users hear my conversation When you pair your headset with your Bluetooth phone you are creating a private link between only these two devices The Bluetooth wireless technology used in your headset is not easily monitored by third parties because Bluetooth wireless signals are significantly lower in radio frequency power than those produced by a typical mobile phone 12 Treo Wireless Headset Caring for your headset Caring for your headset e To clean the headset use a clean soft slightly damp cloth e Always store your headset with the power off and keep it well protected e Avoid storage at high temperatures above 60 C 134 F such as in a hot vehicle or in direct sunlight Storage at high temperatures can degrade performance and reduce battery life e Do not expose the headset or any of its supplied parts to rain or other liquids Glossary Bluetooth Bluetooth profi
6. e of Equipment Headset Model Number Treo Wireless Headset by palmOne Year of Manufacture 2004 I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s Place Milpitas CA Date December 22 2004 Name David Woo Title Senior Compliance Engineer Singapore approval mark hao by IDA Tor use in Singapore DA102238 Australia New Zealand approval mark N10996 Mexico approval mark NOM NYCE NORMALIZACION Y CERTIFICACION ELECTRONICA A C Treo Wireless Headset 17 Copyright and Trademark Copyright and Trademark 2004 palmOne Inc All rights reserved palmOne and Treo are among the trademarks or registered trademarks owned by or licensed to palmOne Inc All other brand and product names are or may be trademarks of and are used to identify products or services of their respective owners palmOne Inc uses the Bluetooth wireless technology trademark under express license from Bluetooth SIG Inc Disclaimer and Limitation of Liability palmOne Inc assumes no responsibility for any damage or loss resulting from the use of this manual palmOne Inc assumes no responsibility for any loss or claims by third parties which may arise through the use of this software palmOne Inc assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction dead battery or repairs Be sure to make backup copies of all impor
7. he headset ear grip is placed over the front of the ear Your headset is ready to wear on the right ear but you can adjust the ear grip to hang from your left ear N NOTE Follow the same procedure to switch the wearing preference from your left ear to your right ear 6 Treo Wireless Headset Choosing wearing preference 1 Hold the headset with the speaker facing you 2 Flip the ear grip down 3 Rotate the ear grip in a half circle counterclockwise 4 Place the headset over your left ear with the ear grip toward the front N NOTE For optimal performance wear your headset and your Bluetooth phone on the same side of your body In general you will get better performance when there are no obstructions including parts of your body between the headset and the phone Treo Wireless Headset Making a call Making a call IMPORTANT Do not hold the multifunction button lt gt down too long when making ending or answering a call This should be only a quick press so you don t accidentally activate your headsets enhanced features described later in this guide 1 Make sure the headset is turned on 2 Dial the number Using the phone s keypad Dial the number on the keypad and then press the Send key Using voice activated dialing Press and release the multifunction button lt gt and then say the name of the person you wish to dial when you hear the tone N NOTE The Treo 650 does not sup
8. he receiver is connected e Consult the dealer or an experienced radio TV technician for help IMPORTANT Changes or modifications not covered in this manual must be approved in writing by the manufacturer s Regulatory Engineering Department Changes or modifications made without written approval may void the user s authority to operate the equipment Treo Wireless Headset 15 Product regulatory information Responsible Party Treo Wireless Headset Product Family palmOne Inc Tested to Comply 400 N McCarthy Blvd C With FCC Standards Milpitas California 95035 United States of America 408 503 7500 FOR HOME OR OFFICE USE Europe R amp TTE Directive Europe Declaration of Conformity Application of Council Directive s 89 336 EEC EMC Directive 99 5 EC RTTE Directive 72 23 EEC Low Voltage Directive Standards to which Conformity is Declared e ETSI301 489 1 Immunity e EN60950 1992 A1 1993 A2 1993 A3 1995 A4 1997 A5 1998 Safety e EN55022 1994 A1 1995 A2 1997 A3 1998 Class B Emissions The product is CE marked The product fulfills the essential requirements of the harmonized standards shown above 16 Treo Wireless Headset Product regulatory information Manufacturers Name palmOne Inc Manufacturers Location 400 North McCarthy Blvd Milpitas CA 95035 5112 USA Importers Name Palm Germany GmbH Importers Location Landsberger Strasse 155 D 80687 Munchen Germany Typ
9. hone and Bluetooth headset Your headset is compatible with most Bluetooth phones that are compliant with the Bluetooth version 1 1 or 1 2 specification Visit your phone manufacturer s website to make sure that your phone has Bluetooth capability Treo Wireless Headset 3 Pairing with your Bluetooth phone Pairing with your Treo 650 smartphone 1 O RB N O Make sure the headset is turned off On the phone go to Applications and select Bluetooth Make sure Bluetooth is on Select Setup Devices and then select Hands free Setup Press and hold the headset multifunction button lt gt for 8 seconds until you see a solid blue light On the phone select Next When the phone finds your headset it displays Treo Headset with a headphone icon next to it Select Treo Headset and then select OK A status message appears telling you that your phone is connecting with your headset When your phone asks for a passkey enter 0000 from your keypad and then press OK On the confirmation screen select Done Treo Wireless Headset Turning your headset on and off Pairing with other Bluetooth phones 1 2 Make sure the headset is turned off Press and hold the multifunction button gt for approximately 8 seconds until you see a solid blue light Set your Bluetooth phone to discover the headset by following your phone s instruction guide Typically the steps involve going to a Setup C
10. les Pairing Radio technology developed to connect devices such as mobile phones and headsets without wires or cords over a short distance of approximately 33 feet 10 meters More information is available at www bluetooth com Industry standard protocols determining how Bluetooth devices communicate with each other Bluetooth phones support different sets of profiles most support the headset profile but some support the hands free profile and others support both profiles In order to support a certain profile a phone manufacturer has to implement certain features in the phone s software Process that creates a unique and encrypted communication link between two Bluetooth devices and allows them to communicate with each other Treo Wireless Headset 13 Passkey or PIN Active mode Standby mode Secret code that needs to be entered on the phone in order to pair the mobile phone with the headset When you pair your mobile phone with your headset the devices recognize each other the phone bypasses the discovery and authentication process and automatically accepts the transmission Mode in which the headset has a call in progress Your headset goes from standby mode into active mode when you receive a call or make a call When the headset is in active mode the blue indicator light flashes every 8 seconds Mode in which the headset passively waits for a call When you end a call on your mobile phone your headset
11. ltifunction button lt gt for 2 seconds until you hear a series of two tones Reject an incoming call When your phone rings press and hold the multifunction button lt gt for 2 seconds until you hear a series of two tones Take a second incoming call call waiting When you are on a call and your phone notifies you of an incoming call press and hold the multifunction button lt gt for 2 seconds until you hear a series of two tones Repeat to switch between calls Put a call on hold While you re on a call press and hold the multifunction button lt gt for 2 seconds until you hear a series of two tones Repeat to retrieve the call N NOTE For the Treo 650 smartphone use the button on your keypad to put a call on hold The Treo 650 smartphone does not support the hands free call hold feature Treo Wireless Headset 11 Common questions Common questions How far away from my phone will my headset work The operating range is typically up to 33 feet 10 meters Does my headset work with my cordless phone at home Your headset is not designed for use with cordless phones Does my headset work with laptop or desktop computers or handhelds Your headset works with devices that are compliant with Bluetooth version 1 1 or later specifications and support the headset and or hands free profile s Will anything cause interference with my conversation when I m using my headset Appliances such as cordless phones an
12. onnect or Bluetooth menu on your phone and then selecting the option to discover a Bluetooth device When your phone finds the Treo Headset it asks if you want to pair with it Confirm this by selecting Yes or OK When your phone asks for a passkey enter 0000 from your keypad and then press Yes or OK If pairing is successful the blue indicator light flashes 10 times rapidly before going back to flashing every 3 seconds If pairing is unsuccessful the light remains solid and you ll need to reattempt pairing using the correct procedure above Turning your headset on and off To turn your headset on and off press and hold the multifunction button lt for 3 to 5 seconds until you see a burst of four flashes on the blue indicator light A series of two tones indicates that the headset has turned on or off Treo Wireless Headset Choosing wearing preference When the headset is on the indicator light flashes When it is off the light stops flashing and remains unlit IMPORTANT Do not hold the button down for more than 3 to 5 seconds when turning the headset on or else it may begin the pairing process and the blue indicator light will turn solid If that happens turn off the headset wait 3 to 5 seconds and then repeat the process for turning the headset on N NOTE You must have the Bluetooth functionality on your phone turned on in order to use your phone with your headset Choosing wearing preference T
13. port voice activated dialing through Bluetooth wireless technology For other phones check with the manufacturer You must set the voice tags on your phone to use voice activated dialing For better reception record the voice tags from the headset 3 Increase or decrease call volume by pressing the volume control buttons gt The tone volume increases or decreases to match the call volume 4 To end a call press and release the multifunction button or press the button to end a call on your phone s keypad 8 Treo Wireless Headset Answering a call Answering a Call 1 Answer a Call From the headset When you hear the phone ring press and release the multifunction button lt gt once From the phone Press the button to answer a call on your phone s keypad Depending on your phone you may then need to press and release the multifunction button gt once to transfer the call to your headset 2 Increase or decrease call volume by pressing the volume control buttons gt lt gt The tone volume increases or decreases to match the call volume 3 To end a call press and release the multifunction button or press the button to end a call on your phone s keypad Using call waiting To use the call waiting feature press the button on your phone to switch to the incoming call typically the Send button You can also use the call waiting enhanced feature described later in this guide if it is
14. tant data on other media to protect against data loss 18 Treo Wireless Headset palmOne Inc 400 N McCarthy Blvd Milpitas California 95035 U S A
Download Pdf Manuals
Related Search