Packard Bell GX User's Manual
Contents
1. 4 Disconnect the system fan cable connector from the header on the main board Wie E 3 i a ee eee nd qi m d Fig 72 Disconnecting the system fan cable Packard Bell iPower GX Disassembly Manual Packard dell 30 5 Remove the screws securing the main board Fig 73 Location of the main board screws 6 Carefully lift out the main board Fig 74 Extracting the main board Note During re assembly of the main board make sure that the small black switch on the main board fits within the slot on the wireless network on off switch HERO ood Wap ze COU et i m u iibro Na Fig 75 Wireless LAN switch GPU Heat Sink To remove the GPU heat sink first remove the main board see Main Board on page 28 and then perform the following steps Packard Bell iPower GX Disassembly Manual ratkard dell 31 1 Turn the main board over 2 Remove the screws that secure the GPU heat sink to the main board Fig 76 Location of the GPU heat sink screws 3 Separate the GPU heat sink from the main board Note During re assembly first use a soft cloth and isopropyl alcohol to remove any thermal grease residue from the heat sink and apply new thermal grease on the main board s graphics processor Use only enough to cover the processor die Modem Jack USB Board To remove the modem jack USB board first remove the main board see Main Board on page 28 and then perform the f2. Fig 51 Location of the top cover screws bottom 4 Turn the notebook over so the top is facing up 5 Remove the screws from the top of the top cover Fig 52 Location of the top cover screws top Note Note the location of the screw types and sizes Packard Bell iPower GX Disassembly Manual ratkard dell 23 6 Lift the top cover assembly up from the notebook Fig 53 Removing the top cover Touchpad Board To remove the touchpad board first remove the top cover see Top Cover on page 21 and then perform the following steps 1 Turn the top cover over so the backside is facing up 2 Remove the screws from the touchpad board bracket Fig 54 Location of the touchpad board bracket screws 3 Remove the screws from the touchpad button board bracket d eg Lp i 3i 72 REDO FLW mA W umopus Ec HB M SOT WAAAY mA x unns gi pn XB FTIO Pu mi wu Fig 55 Location of the touchpad button board bracket screws Packard Bell iPower GX Disassembly Manual ratkard dell 24 4 Swing the brown touchpad connector clip upward and lift the cable out of the connector Be careful not to touch or damage any other components Fig 56 Disconnecting the touchpad flat cable 5 Remove the touchpad board bracket from the notebook Fig 57 Removing the touchpad board bracket 6 Remove the touchpad board from the notebook Touchpad Button Board To remove the touchpad button board first re
3. from the inside of the battery compartment Fig 23 Location of the keyboard cover screws 2 Turn the notebook over so the top is facing up and open the LCD completely 3 Insert the flat blade screwdriver under each of the hinge covers and gently pry them up Fig 24 Opening the hinge covers 4 Pull the cover off the notebook by lifting the back corners of the cover and let it rest on the LCD panel Be careful not to damage the LCD panel E EN M 0M M i Tiri m LE Fig 25 Releasing the keyboard cover Note The cover is connected to the notebook by one cable Do not pull the cable Packard Bell iPower GX Disassembly Manual 14 ratkard dell 5 Carefully release the black clip securing the flat cable and disconnect the cable from the header on the main board Fig 26 Releasing the keyboard cover flat cable 6 Remove the keyboard cover Power Button Board The power button board is located on the inside of the keyboard cover To remove the power button board first remove the keyboard cover see Keyboard Cover on page 13 and then perform the following steps 1 Release the white clip securing the flat cable and disconnect the cable from the header on the power button board Fig 27 Location of the power button board 2 Remove the screw securing the power button board to the keyboard cover see Fig 27 3 Remove the power button board Volume Control Board The volume
4. unit Fig 47 Removing the LCD assembly Nofe Ensure that all cables are clear of the base before lifting the LCD assembly upward LCD Panel To remove the LCD panel first remove the LCD assembly see LCD Assembly on page 19 remove the inverter see Inverter on page 18 remove the webcam see Webcam on page 18 and then perform the following steps Packard Bell iPower GX Disassembly Manual Packard dell 21 1 Remove the screws securing the LCD panel es ee ee LI Fig 48 Location of the LCD panel screws 2 Hold the LCD panel by the sides lift out the panel and remove it from the housing Note During LCD panel re assembly make sure that the magnet has remained in the magnet bracket Fig 49 Location of the LCD panel magnet bracket LCD Panel Hinges To remove the LCD panel hinges first remove the LCD panel see LCD Panel on page 20 and then perform the following steps 1 Remove the LCD panel hinges Top Cover To remove the top cover first remove the LCD assembly see LCD Assembly on page 19 and then perform the following steps Packard Bell iPower GX Disassembly Manual ratkard dell 22 1 Slide the brown touchpad connector clip to the back of the notebook and remove the flat cable from the header ee ee SE OEN a ee be og Pe T EE Fig 50 Releasing the touchpad flat cable 2 Turn the notebook over so the bottom is facing up 3 Remove the screws from the bottom of the notebook
5. wm 3 1 x im La 225 T i i t E 8 RE l z fens m s i Bd kale En ees dim rm Fig 18 Location of the hard disk drive bracket screws 6 Separate the metal bracket and the hard disk drive qe cR z539w c wies V TETTE UE LV TE E UU OA MTN ENS MNT 9 E 890 0S2 QSL L6CRRr Vg si9 9ueJ8g INC SA3800S20 01snzz Sn3800S20M oid o2S QM Fig 19 Separating the hard disk drive from the bracket Packard Bell iPower GX Disassembly Manual Packard pell 12 DVD Drive To remove the DVD drive first remove the battery see Battery on page 4 and then perform the following steps 1 Remove the rubber insert from the bottom of the notebook Fig 20 Removing the DVD drive screw cover 2 Remove the screw that secures the DVD drive to your notebook Fig 21 Location of the DVD drive screw 3 Carefully slide the drive out of the drive bay Mab UII Fig 22 Removing the DVD drive Packard Bell iPower GX Disassembly Manual ratkard dell 13 Note Use a small screwdriver or a scribe to push on the DVD bracket and slide the drive out of the bay Keyboard Cover The keyboard cover also houses the power button board the volume control button and the multimedia board To remove the keyboard cover complete first remove the battery see Battery on page 4 and then perform the following steps 1 Remove the two keyboard cover screws
6. Packard Bell iPower GX Disassembly Manual ratkard dell 1 Table of Contents fitere EM Lule C NT TT 2 FOL NOE INON ANO en periit eietesetebeie eive eie ebeieiei eee EED A a EE ana RE 2 Technician Nolo R M 2 DCC 06 m E E E E E 2 FR So Cl MOI ossusapREEIEEIEEIEEIEIEEEEEIEIIEIE ICI T ACIE 2 HOOHIEFOd TOOG sepatu MEER MEME MMEEEEEEEEREEMMEPEUU MEME EEEUEEE 2 FIZ AN OUS VON OS MR TREES 3 Avoid Ele irostatie ID ISCMal OG 2isc c2cssccssecssesssasssasssasssasssasssasasasasseasasasaiasatsaaaanecancatacutacutacusacaausacuseguadacs 3 OWE OUPIONY WAM EEATT 3 zig eee eee 4 PUNE MON Vi xn 4 CPO RCAL SINK aa E E 5 S a ee E E E AE EI EES ee ee ee E EEE 6 Wireless LAN AQaplel acsesessiecssacssecssecanacsnecnecnecanscanausnscaneasuacauacanecsnecsneceneceneaeneaeneceueaeueceneaeneasueasacaeneacaeaged 7 PUG OEY E 9 mz CLA IGF WII 10 TD IN M M H 12 HoUDOdI d COUDI ane it et ee ee ee ee ere 13 FONT ES EO BOI Cs saspe DERE EIER daiadaisdiisaaisaaisgiisaaisiads 14 WOIUIEMCS GORU Ol DOAN MERERETUR 14 PCTS ONAL mro AEC TET 15 Fy DO hisses T 16 LOD BOZO c E 17 lii EE E E E E 18 WSCA WERE 18 HID FASS SIMO IN A 19 LOU Tel cn ceeedeceoucucncuen cucscueecuescuescues
7. bles or components If the existing tape cannot be reused replace it with the same type conductivity of tape Do not use cellophane tape Heassembly Reassembly is the reverse of the disassembly process Use care to ensure that all cables and screws are returned to their proper positions Check that no tools or any loose parts have been left inside the casing Check that everything is properly installed and tightened Required Tools To disassemble the computer you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge Small Phillips screwdriver Small flat screwdriver Scribe or non marring tool Packard Bell iPower GX Disassembly Manual ratkard dell Hazardous Voltage There is hazardous voltage present inside the notebook when it is connected to an AC supply even when the notebook s power switch is off Exposure to hazardous voltage could cause personal injury To avoid risk of injury contact an Authorized Service Provider for proper unjinstallation of optional hardware devices Avoid Electrostatic Discharge Electrostatic electricity can easily damage circuit cards and integrated circuits ICs To reduce risk of damage store them in protective packaging whenever they are not installed in the system Add in cards can be extremely sensitive to electrostatic discharges ESD and always require careful handling After removing the card from the notebook place the ca
8. control board is located on the inside of the keyboard cover To remove the volume control board first remove the keyboard cover see Keyboard Cover on page 13 and then perform the following steps Packard Bell iPower GX Disassembly Manual 15 Packard dell 1 Carefully release the black clip securing the flat cable and disconnect the cable from the header on the volume control board eT E Ti 3 iid y 1 i m dom YHN604BD02001081016 01 REV AO1 BY venas D inutiliter edd DATE S114 C Fig 28 Location of the volume control board 2 Gently push the volume control board from the inside out of the keyboard cover Multimedia Board The multimedia board is located on the inside of the keyboard cover To remove the multimedia board first remove the keyboard cover see Keyboard Cover on page 13 and then perform the following steps 1 Carefully release the white clip securing the power button board flat cable and disconnect the cable from the header on the multimedia board TERRE Lu isTe 11 25 02 E EZ 9 48B 41206 011 CCROBDUCHI C0 LOCIs 0s Fig 29 Releasing the power button board flat cable 2 Remove the five screws securing the multimedia board to the keyboard cover E Fig 30 Location of the multimedia board screws Packard Bell iPower GX Disassembly Manual ratkard dell 16 3 Release the multimedia board and lift the board from the right the multimedia board is still connect
9. dapter and all power and signal cables from the system 3 Turn the notebook upside down Note Use an anti static mat or something soft like a piece of cloth underneath the notebook to prevent damage to the exterior of the notebook 4 Slide the battery lock unlock latch into the unlock position Fig 1 Releasing the battery 5 Slide the battery release latch into the release position and slide the battery out of the unit Fig 2 Removing the battery Memory To remove the memory installed first remove the battery see Battery on page 4 and then perform the following steps 1 Loosen the screws securing the CPU bay cover the screws cannot be removed Fig 3 Location of the CPU bay cover screws Packard Bell iPower GX Disassembly Manual Packard dell 5 2 Use the thumb notch to lift the CPU bay cover and remove it Be careful not to break off the tabs located on the end of the cover opposite the thumb notch Fig 4 Opening the CPU bay cover 3 Gently press outward the clip on each side of the memory module the module will eject upward Fig 5 Releasing the installed memory module 4 Carefully remove the memory module out of the slot TTD 2T0DDSSK SOD Fig 6 Removing the memory module CPU Heat Sink To remove the CPU heat sink first remove the battery see Battery on page 4 and then perform the following steps 1 Loosen the screws securing the CPU bay cover the screws cannot b
10. e removed see Fig 3 Packard Bell iPower GX Disassembly Manual Packard dell 6 2 Use the thumb notch to lift the bay cover and remove it Be careful not to break off the tabs located on the end of the cover opposite the thumb notch see Fig 4 3 Loosen the screws that secure the heat sink to the system board Use the numbers stamped in the metal next to each screw and loosen the screws in reverse numerical order start with 5 then 4 then 3 then 2 and finally 1 Fig 7 Location of the CPU heat sink screws Note Screws 1 to 4 are captive and you cannot remove them When tightening the heat sink screws into the numbered holes during re assembly tighten them in numerical order 4 Atthe same time as you lift move the heat sink away from the side of the notebook and remove the heat sink Note Before re assembling the heat sink remove any thermal grease residue from the CPU using a soft cloth and isopropyl alcohol Apply new thermal grease on the CPU use only enough to cover the CPU die CPU To remove the CPU first remove the heat sink see CPU Heat Sink on page 5 and then perform the following steps Packard Bell iPower GX Disassembly Manual Packard dell 1 Use a flat blade screwdriver to turn the CPU lock screw 1 4 turn counter clockwise Ta m er a ga m m ux DH Pp i EE T Dd EET MET Fig 9 Releasing the CPU screw 2 Take out the CPU from the socket Fi
11. eader on the main board zou 38 El Ug BI am cut ri s TJ t TA F ows 3 E a y We aye oly eee pee ES us le y aoe Baraj gha 4 ORE pi a hl C a L PPT Ln eU FERPA D Fig 14 Disconnecting the RTC battery 2 Detach the RTC battery from the main board Nofe The RTC battery is held in place by double sided tape Packard Bell iPower GX Disassembly Manual ratkard Jell 10 Hard Disk Drive To remove the hard disk drive s first remove the battery see Battery on page 4 and then perform the following steps 1 Loosen the screws securing the hard disk drive bay cover the screws cannot be removed AUI Fig 15 Location of the hard disk drive bay cover screws 2 Use the thumb notch to lift the bay cover and remove it Be careful not to break off the tabs located on the end of the cover opposite the thumb notch TUA A Fig 16 Removing the hard disk drive bay cover Packard Bell iPower GX Disassembly Manual ratkard dell 3 Pull the plastic tab on the hard disk drives towards you to disconnect the drives Fig 17 Disconnecting the hard disk drives 4 Take the drives out of the bay 5 Remove the four screws Phillips head on the metal bracket holding the hard disk drive j PT wt Hr J 0 TELE E 1 E m im ow D II ll FE E a ia FE G2 E Fe E iis ct om Emm in s E Rod it oS m Be EB 2 485 ag e zz om s g mu
12. ed to the volume control board by means of a flat cable 4 Lift the black clip securing the volume control board flat cable and disconnect the cable from the header on the multimedia board Note f needed release the black clip securing the flat cable with the blue end and disconnect the cable from the header on the multimedia board Keyboard To remove the keyboard first remove the keyboard cover see Keyboard Cover on page 13 and then perform the following steps 1 Remove the five keyboard screws hr RA TUN PLANOS Fig 32 Location of the keyboard screws Note The keyboard is secured with two long and three short screws Note the location of the long screws 2 Liftthe back edge of the keyboard slightly and then slowly slide it toward the LCD panel to release the keyboard retaining tabs located on the front edge of the keyboard CO Fig 33 Releasing the keyboard Packard Bell iPower GX Disassembly Manual 17 ratkard dell 3 Before removing the keyboard entirely carefully release the black clip securing the flat cable and disconnect the cable from the header on the main board Am Pip Fig 34 Releasing the keyboard flat cable 4 Remove the keyboard LCD Bezel You can complete this procedure with the LCD assembly connected to the notebook The LCD assembly shown in the following pictures has been removed from the notebook for clarity To remove the LCD bezel first remove the
13. entation and detailed product specifications Technician Notes Only technicians authorized by Packard Bell B V should attempt to repair this equipment All troubleshooting and repair procedures are detailed to allow only subassembly module level repair Because of the complexity of the individual boards and subassemblies no one should attempt to make repairs at the component level or to make modifications to any printed wiring board Improper repairs can create a safety hazard Any indication of component replacement or printed wiring board modifications may void any warranty or exchange allowances Disassembly When disassembling the system unit follow these general rules Turn OFF the power to the system and all peripherals using the power button Unplug the AC adapter and all power and signal cables from the system Remove any SD MMC card ExpressCard or dummy card from the computer Do not disassemble the system into parts that are smaller than those specified in the instructions Label all removed connectors note where the connector goes and in what position it was installed m The screws for the different components vary in size Group the screws with the corresponding components during the disassembly process to avoid mismatch when putting back the components m Observe the order of the disassembly steps to prevent damaging any of the hardware components m Some of the procedures in this guide involve removing tape that holds ca
14. esescsesceescsescsescseecseeaseeaseeaseeauen ance aseeaneecseeaseeaneeaseeaseecneeaseeaseecseeeseseseu 20 EG BEL age o o m 21 TOD 60 e oe 21 MPO UG Fe GS O WO ar E EEE EEEE E E ES 23 Touchpad B ton Boal TET 24 FINJON TAC AGN oorsese rn EEE O EEEE E EEEE E EEEE ERr 25 BUTO relig NR m 25 NWN CLE tel cece ven cuaceueseueccueneseneueseueseueneueneuen UOTE Om 26 nS Oo Fac AS EMD EIE DEREEEEMEU DER PDEDEIEUEIUREEEEEEUU INE ERMUEEBPEU E CUEDEDEEEEREEE 27 PUTS ON o NENNT 28 A TAC A Moe RR RRERE P S 30 Modem Jacks USB BOGSF itte eee e etie be pec erede Ie pe BA PROS DA na ini Bo PADS DR ERE HAM irn ii HERE Ad inihain i 31 ovsteimddllass IERI EMEEDMEEEERI EE RIDERE IMEEM IERI EEEUE 32 Oll eerste nen nce een een nce eee eee eve eve ee vee nn nn EEE EEE RE RnR REE 33 Packard Bell iPower GX Disassembly Manual Packard pell 2 About This Guide This guide contains systematic disassembly instructions for the Packard Bell iPower GX The instructions are illustrated where necessary with images of the part that is being disassembled Packard BellB V reserves the right to make changes to the iPower GX without notice For More Information For more information about the Packard Bell iPower GX visit Packard Bell s support web site at www packardbell com The support web site also has links to additional Packard Bell docum
15. g 10 Removing the CPU Wireless LAN Adapter To remove the wireless LAN adapter first remove the battery see Battery on page 4 and then perform the following steps 1 Loosen the screws securing the CPU bay cover the screws cannot be removed see Fig 3 2 Use the thumb notch to lift the bay cover and remove it Be careful not to break off the tabs located on the end of the cover opposite the thumb notch see Fig 4 Packard Bell iPower GX Disassembly Manual Packard dell 3 Carefully disconnect the two WiFi antenna cables rig US B omo erae TC HB 1 Ww Fig 11 Disconnecting the wireless LAN antenna cables Note There are two WiFi antenna cables connected to the wireless LAN adapter Take note of which coloured wire is connected to which connector on the adapter 4 Remove the screws securing the wireless LAN adapter it will eject upwards oo A i a A 5 T bles 4 Fig 12 Location of the wireless LAN adapter screw Packard Bell iPower GX Disassembly Manual Packard dell 5 Take out the wireless LAN adapter from the socket Fig 13 Removing the wireless LAN adapter RTC Battery The RTC battery is encased within a special black sleeve and has a wire connector that connects to the main board To remove the RTC battery first remove the wireless LAN adapter see Wireless LAN Adapter on page 7 and then perform the following steps 1 Disconnect the RTC battery cable from the h
16. keyboard cover see Keyboard Cover on page 13 and then do the following 1 Remove the six rubber inserts from the front of the LCD bezel Fig 35 Location of the LCD bezel screw covers 2 Remove the screws that became accessible after removing the inserts 3 Carefully pry open the LCD bezel it has been clicked into place f Fig 36 Removing the LCD bezel Packard Bell iPower GX Disassembly Manual ratkard pell 18 Inverter You can complete this procedure with the LCD assembly connected to the notebook To remove the inverter first remove the LCD bezel see LCD Bezel on page 17 and then do the following 1 Remove the screws securing the inverter board i Kam Fig 37 Location of the inverter screws 2 Liftthe inverter from the LCD panel and turn it over Fig 38 Removing the inverter 3 Disconnect the cables from the headers on the inverter board S EX T _ _ gt Fig 39 Disconnecting the inverter cables Webcam You can complete this procedure with the LCD assembly connected to the notebook To remove the webcam first remove the LCD bezel see LCD Bezel on page 17 and then do the following 1 Disconnect the cable from the header on the webcam module Fig 40 Location of the webcam connector 2 Hemove the screws that secure the webcam Fig 41 Location of the webcam module screws Packard Bell iPower GX Disassembly Manual ratkard dell 19 3 E
17. move the touchpad board see Touchpad Board on page 23 and then do the following Packard Bell iPower GX Disassembly Manual ratkard dell 25 1 Swing the black fingerprint reader connector clip upward then lift the cable out of the connector see Fig 56 2 Remove the touchpad button board from the notebook Fingerprint Reader To remove the fingerprint reader first remove the touchpad button board see Touchpad Button Board on page 24 and then perform the following steps 1 Remove the fingerprint reader from the notebook Fig 60 Removing the fingerprint reader Bluetooth To remove the Bluetooth module first remove the top cover see Top Cover on page 21 and then perform the following steps 1 Liftthe Bluetooth module out of the notebook PRATT Fig 61 Detaching the Bluetooth module Packard Bell iPower GX Disassembly Manual ratkard dell 26 Note The Bluetooth module is held in place by double sided tape 2 Disconnect the cable from the header on the Bluetooth module Fig 62 Disconnecting the Bluetooth cable Modem To remove the modem first remove the top cover see Top Cover on page 21 and then perform the following steps 1 Remove the screws securing the modem to the main board Fig 63 Location of the modem screws Packard Bell iPower GX Disassembly Manual ratkard dell 27 2 Remove the modem from the main board Fig 64 Removing the modem 3 Tur
18. n the modem over and unplug the cable from the header on the modem Fig 65 Releasing the modem cable Speaker Assembly To remove the speaker assembly first remove the top cover see Top Cover on page 21 and then perform the following steps 1 Disconnect the speaker cable connector from the header on the main board Fig 66 Disconnecting the speaker cable Packard Bell iPower GX Disassembly Manual Packard dell 28 2 Remove the three screws securing the speakers to the notebook Fig 67 Location of the speaker assembly screws 3 Clear the speaker cables and remove the speakers from the notebook Fig 68 Removing the speaker assembly Main Board To remove the main board remove the memory modules see Memory on page 4 remove the CPU see CPU on page 6 remove the wireless LAN adapter see Wireless LAN Adapter on page 7 remove the hard disk drives see Hard Disk Drive on page 10 remove the DVD drive see DVD Drive on page 12 remove the right speaker see Speaker Assembly on page 27 remove the top cover see Top Cover on page 21 and then perform the following steps 1 Disconnect the Bluetooth cable connector from the header on the main board Fig 69 Location of the Bluetooth cable header on the main board Packard Bell iPower GX Disassembly Manual ratkard dell 29 2 Remove the modem cable from the main board retaining clips p ra h Fig 71 Location of the EMI shield screw s
19. ollowing steps 1 Remove the screw securing the modem jack USB board Fig 77 Location of the modem jack USB board screw Packard Bell iPower GX Disassembly Manual Packard dell 32 2 Lift the modem jack USB board from the notebook Fig 78 Extracting the modem jack USB board screw System Fan To remove the system fan first remove the main board see Main Board on page 28 and then perform the following steps 1 Remove the screws securing the system fan m Fig 79 Location of the system fan screws 2 Remove the system fan from the notebook e I 2 Oo S 2 E i GEL c vu di 2 Fig 80 Extracting the system fan Packard Bell iPower GX Disassembly Manual ratkard pell 33 Notice The information in this guide is subject to change without notice This guide contains information protected by copyright No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B V PACKARD BELL B V SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING PERFORMANCE OR USE OF THIS MATERIAL Copyright 2009 Packard Bell B V All rights reserved Packard Bell is a registered trademark of Packard Bell B V The names of actual companies and products mentioned herein may be trademarks and or registered trademarks of their res
20. pective owners The software described in this guide is furnished under a license agreement or nondisclosure agreement The software may be used or copied only in accordance with the terms of the agreement iPower GX Disassembly Manual Author Juan M Calvino Alonso First Edition February 2009 Version 1 0 Part Number CS013A00 Packard Bell B V www packardbell com Packard Bell iPower GX Disassembly Manual
21. rd flat on a grounded static free surface component side up Use a conductive foam pad if available but not the card wrapper Do not slide the card over any surface Before you install or remove memory modules video memory disk drives circuit cards or other devices protect them from static electricity To do so make sure the notebook s power switch is OFF Then unplug the notebook s AC power cord Before picking up the device you un install you should wear an anti static wrist wrap available at electronic supply stores Be sure to connect the wrist wrap to an unpainted metal portion of the notebook casing As an alternative you can dissipate electrostatic build up by touching an unpainted metal portion of the notebook casing with one hand Then touch the device you are un installing with the other hand and maintain continuous contact with it until it is un installed in the notebook Power Supply Unit Under no circumstances should you attempt to disassemble the power supply The power supply contains no user serviceable parts Inside the power supply are hazardous voltages that can cause serious personal injury Always return a defective power supply to the dealer WARNING Ensure that the notebook is disconnected from its power source and from all telecommunications links networks or modem lines whenever the casing cover is removed Do not operate the notebook with the cover removed AVERTISSEMENT Assurez vou
22. s que le syst me est d branch de son alimentation ainsi que de toutes les liaisons de t l communication des r seaux et des lignes de modem avant d enlever le capot Ne pas utiliser le systeme quand le capot est enlev WARNUNG Das System darf weder an eine otromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung einem Netzwerk oder einer Modem Leitung haben wenn die Geh useabdeckung entfernt wird Nehmen Sie das System nicht ohne die Abdeckung in Betrieb ADVERTENCIA Asegurese de que cada vez que se quite la cubierta del port til el sistema haya sido desconectado de la red de alimentaci n y de todos lo enlaces de telecomunicaciones de red y de l neas de m dem No ponga en funcionamiento el sistema mientras la cubierta est quitada WAARSCHUWING Zorg er voor dat alle verbindingen van en naar de notebook stroom modem netwerk etc verbroken worden voordat de behuizing geopend wordt Zet de notebook nooit aan als de behuizing geopend is AVVERTENZA Prima di rimuovere il coperchio del telaio assicurarsi che il sistema sia scollegato dall alimentazione da tutti i collegamenti di comunicazione reti o linee di modem Non avviare il sistema senza aver prima messo a posto il coperchio Packard Bell iPower GX Disassembly Manual Packard dell 4 Battery Perform the following steps to remove the battery 1 Make sure the power to the system is off 2 Unplug the AC a
23. xtract the webcam module Fig 42 Removing the webcam module LCD Assembly To remove the LCD assembly first disconnect the two antenna cables from the wireless LAN adapter see Wireless LAN Adapter on page 7 remove the keyboard see Keyboard on page 16 and then perform the following steps 1 Turn the notebook upside down 2 Remove the two screws securing the LCD assembly hinges on the bottom of the chassis Fig 43 Location of the LCD assembly hinge screws bottom Turn the notebook over so the top is facing up Carefully open the LCD assembly entirely Make sure that you grasp the plastic connector carefully and pull to disconnect the LCD video cable from the header on the main board jeg BE i 4 Fig 44 Disconnecting the LCD video cable Nofe The LCD video cable connector is fragile Packard Bell iPower GX Disassembly Manual 20 ratkard dell 6 Pull the wireless LAN antenna cables out from under the main board and slide the antenna cables and LCD cables out from under the retaining clips Remove any tape that may be securing the cables Fig 45 Disconnecting the WLAN antenna cables Nofe Take care to note the cables routing and positions as they have been installed by Packard Bell 7 Remove the two screws securing the LCD assembly hinges on the top of the chassis Fig 46 Location of the LCD assembly hinge screws top 8 Liftthe LCD assembly upward and remove it from the
Download Pdf Manuals
Related Search