Overland Storage SAN S2000 User's Manual
Contents
1. 1ooog oo Po mnocHg0oo Figure 5 Attaching Front of Rail 10400276 003 06 2010 2010 Overland Storage Inc Page 2 of 6 10400276 003 06 2010 N Q2 2 o o JO0QOGODQDOOO0DOO0OODE Figure 8 Using the Early Round Hole Adaptors 3 Using the screws from the kit secure the front of the rail to the rack 4 Slide the rear rail segment rearward until the rear adaptor holes are in line with holes being used 5 Using the screws from the kit secure the rear of the rail to the rack 6 Repeat Steps 1 5 for the right rail 7 Verify that the rails are level and straight Continue the installation with Install the Unit in the Rack Install the Unit in the Rack WARNING Itis recommended that a mechanical lifter or at least two people be used during rack installation or removal to prevent injury AVERTISSEMENT pour viter toute blessure il est recommande qu un monte charge ou deux personnes au moins soit utilis lors de l installation ou de l enl vement du support 1 At the front extend the middle rail members until they lock click 2 Confirm that the ball bearing shuttles are at the front Figure 9 Bearing Shuttle Figure 9 Inserting Expansion Array Into Rack 3 Using a mechanical lifter or two people insert the appliance into the rack rails Lift the appliance to its install height and e2. of 2010 Overland Storage Inc 1 23 45 6 7 8 9 1 AC Power 4 Dual USB Ports 7 Data Port 1 2 Mouse Port 5 COM Port 8 Data Port 2 3 Keyboard Port 6 Video Port 9 Active SAS Port Figure 15 SAN 2000 Rear Panel Connections 1 Plug the network connection into Data Port 1 Using a Category 5e or better cable connect Data Port 1 on the appliance to a Gigabit Ethernet switch on the same LAN segment as the management system 2 Attach the power cords to the AC Power sockets on back panel 3 Plug the power cords into an UPS appliance or AC power source 4 Make sure that a iSCSI Initiator and the NET dot NET framework is installed on each Windows host before continuing 5 Install the Windows SAN Manager Suite software from the supplied CD on a host computer attached to the same subnetwork e If Autorun is enabled program launches an HTML contents page where you select the appropriate type of software to load 32 bit or 64 bit e Ifyou are using a Mozilla based browser or Autorun is disabled you need to use your file manager to browse the CD and launch start html at the root level 6 Follow the on screen instructions Power Up the SAN 2000 IMPORTANT Always turn on any EXP E2000 expansion units on before powering up your SAN S2000 This enables the head unit to discover the attached expansions Page 4 of 6 To turn the appliance ON press and hold the Power button Figure 16
3. Try to keep the name short d At the Password page you must enter a password for the appliance confirm it and click Next IMPORTANT Overland recommends using a password of at least six alohanumeric characters e At the Pool Creation page select the type of policy you want and click Next See the user guide for complete details NOTE Select the Don t Create Pool option if you want to create multiple pools or to create a pool using only selected disks in the enclosure Later use Windows SAN Manager to create the desired pools 10400276 003 06 2010 2010 Overland Storage Inc f At the Summary page click Close to accept your settings When the wizard finishes the Windows SAN Manager Home screen is displayed Configuration Information At this point your SAN 2000 is ready to be configured for your specific environment and needs The Windows SAN Manager software provides easy access to the Overland storage systems on the network You can also use the built in SAN Web Manager to configure a specific appliance even from a non Windows system Launching the SAN Web Manager 1 From a Web browser enter the applicable IP address to access the SAN 82000 2 Use the following default login case sensitive User Name admin Password password or new assigned password The Web GUI appears 3 Continue with the configuration process Check for Software Updates The latest release of the SAN S2000 softwar
4. 2010 Overland Storage Inc SnapServer SAN 2000 Quick Start Guide Rack Installation Before installing the disk drives it is recommended that the unit first be secured in the rack WARNING Use care during rack installation or removal to prevent accidental tipping of the rack causing damage or personal injury AVERTISSEMENT soyez prudent lors de l installation ou de l enl vement du support afin d emp cher le renversement accidentel de la cr maill re pour viter dommages et blessures The rail kit included with the S2000 is adaptable for installation in the two major types of hardware racks squared holed and round holed EIA 310 racks NOTE A two post telco style rack or any rack that is less than 29 inches in depth will not support this appliance Also for threaded hole racks Overland Storage recommends using a shelf The rails are not universal They are stamped LH left and RH right and must be mounted on the appropriate side when facing the rack front Attach Inner Rails to Chassis This procedure is required for all rack types 1 Mark the screw holes on the rack where the rails will be installed NOTE Be sure rear holes are horizontally in line with the front holes to ensure the unit remains level 2 Remove the inner rail Figure 2 from the rail set Inner Member Latch Middle Member Latch Hidden Outer Member Middle Member Figure 2 Inner Rail Release Latch a Fully
5. for no more than one 1 second to begin the power up sequence a N Power Button Reset Access O RESET Power 3 _ Q e HDD NIC 2 _ fa ea e NIC1 Power gt Us lt 4 Overheat Fail X J Fan Fail Figure 16 Front Panel Controls and Indicators After you turn the power ON the System performs a self test process which takes a few minutes You must leave the appliance ON while completing any configuration processes for your application and backup media servers 1 At the host computer launch the Windows SAN Manager by selecting Windows Start gt All Programs gt SnapServer SAN gt SnapServer SAN Manager Automatically Windows SAN Manager attempts to discover any new SAN S2000 appliances connected to the subnetwork and tries to connect to them 2 If successful Windows SAN Manager then opens the SAN Appliance Setup Wizard to guide you through the following setup process a At the Before You Begin page click Next b At the Licensing Agreement page read the terms click the check box to indicate you accept the terms and then click Next c At the Identity page enter a new name if you want to rename the appliance and click Next NOTE We highly recommend changing the name to help identify the appliance on the network The name must start with a letter subsequent characters may be letters numbers or hyphens
6. 10400276 003 06 2010 Overview This document describes how to unpack an SnapServer SAN 2000 appliance from Overland Storage and install it into a four post 32 inch depth EIA 310 rack WARNING To reduce the risk of electric shock or damage to equipment always remove any power cords while working with the unit AVERTISSEMENT pour r duire le risque de choc lectrique ou endommagement de l quipement retirez toujours les cordons lectriques en travaillant avec l appareil CAUTION While working with the unit observe standard Electrostatic Discharge ESD precautions to prevent damage to micro circuitry or static sensitive devices Register First Before starting it is essential that you activate your Overland warranty Technical and warranty support are not available until this is done 1 Go to the Overland Storage web site http www overlandstorage com 2 Click the Service amp Support tab 3 Select My Products tab gt Register New Product 4 At the Site Login enter your e mail address and password Figure 1 NOTE If you are not yet a member click New member and follow the instructions given It s free and easy E mail Password C lRemember Me Figure 1 Support Site Login 5 Fill in the information and click Submit Within three business days you will receive an e mail from Overland with your warranty certificate Follow the instructions included to complete the process
7. Figure 13 Inserting Drive Carriers 5 Push the lever in to lock the assembly in the bay 6 Repeat Steps 1 5 for each remaining drive carriers IMPORTANT To maintain proper airflow and cooling a drive assembly or a blank drive carrier must be installed in every slot No empty slots are allowed Attach the Bezel Once in the rack attach the front bezel Figure 14 WY A QS l 2 4 2 f 3 Meeseosedes f 08 weseaess leseese A 33 1 COo 5 ae t oN O Ln seseetts Figure 14 Attaching the Bezel 1 Insert the bezel tabs into the flange holes 2 Push the other side in until it latches clicks 3 If desired lock the bezel 10400276 003 06 2010 Cable Attachment All cabling and power connections are located on the rear panel of the SAN 2000 appliance Figure 15 All unit cooling exhaust is handled through the rear panel ee ae ee AIAR eg0000000000F o0 O 00000000 0008 00 O m da000c000000 00 O
8. e can be obtained from the Overland Storage FTP site 1 Point your browser to ftp ftp overlandstorage com Software Snap 2 Open the appropriate version folder 3 Download the latest software file based on the date For additional assistance search at http support overlandstorage com Special Notes e The alarm mute and disable buttons can be found in different places e Inthe Windows SAN Manager they are found in the tasks list under Manage SnapServer SAN Pool e Inthe SAN Web Manager they are found by clicking the subsystem name link under Pools e To help identify a disk drive that is currently allocated as a Hot Spare the red LED blinks on the front of its drive carrier This blinking action also denotes that the Hot Spare is active and healthy e If your OS supports MPIO you must install and enable MPIO with your 1SCSI initiator e Replication and Mirroring are optional features that require additional licenses to activate Page 5 of 6 Additional Information Warranty and Technical Support For warranty and technical support information see our User Guide Contact Us web page For detailed information on configuring your SAN 2000 To search for more service information visit our Expert refer to the SnapServer SAN S2000 User Guide Knowledge Base System It is available online at http support overlandstorage com support snapserver san htm You can get additional technical support on the Int
9. ernet at http support overlandstorage com or by contacting Overland Storage using the information found on the Contact Us page on our web site 10400276 003 06 2010 2010 Overland Storage Inc Page 6 of 6
10. extend the rail set b Push the inner member latch down and remove the inner rail Page 1 of 6 c Release and slide the middle member back into a Position the rail against the inside of the rack front the outer member rail with the hooks in line with the holes l b Insert the bracket front into the rack rail and Middle Member Latch press down so that the hooks catch The spring loaded tabs will extend into the hole to prevent the rail from unhooking Outer Member c Slide the rear segment of the bracket rearward until the hooks are in line with the correct holes d Insert the bracket rear into the rack rail and press down so that the hooks catch and the tabs lock eo 2 Repeat Step 1 for the right slide rail assembly Middle Member f 3 Verify that the rails are level and straight Figure 3 Inner Rail Release Latch 3 a Continue with Install the Unit in the Rack on page 3 3 Attach the right inner member Figure 4 Round Holed Rack Installation Before installing the rails onto a unthreaded round holed rack the round hole rail kit adaptors Figure 6 must be installed on the ends of the outer rails Align Rear A Holes to Tabs Front S o o o N 0 o IQ A o BA gli l l B N Rear Figure 6 Round Holed Rack Adaptors 1 Attach the adaptors Figure 7 to both ends of the Figure 4 Attach Inner Rail Member to E2000 rail a Facing the chassi
11. ngage the inner members on the appliance with the middle members protruding from the rack and slide the appliance into the rack until it stops 4 Slide the unit in and out a few times to ensure that the expansion array does not bind If binding occurs verify that the front and rear flanges are mounted in the correct holes readjusting the slide positioning as necessary 5 Using the two screws provided secure the expansion array flanges to the rack Figure 10 Figure 10 Secure the Expansion Array to Rack Disk Drives The S2000 comes without disk drives installed they are sold separately in singles and 4 packs A combination of 4 to 12 SAS and or SATA drives can be installed with blank drive carriers filling in the empty slots Recommended Drive Configurations Before installing or adding drives to a SAN 82000 server the following must be observed e Different capacity drives can be installed however they should not be included in the same RAID array because capacity usage for all drives in the RAID is limited to the capacity of the smallest drive member e Drives of different rotational speed such as SAS and SATA drives can be installed Figure 11 but they should not be installed in the same column or be separated from each other by a column of different rotational speed drives Figure 12 If you are combining drives with different speeds use the figures below to plan where to place the di
12. s position the rail against the right side of the appliance with the locking tabs Adaptor t going through the holes on the rail A Stamp b Slide the rail toward the front to lock it Th This may require some force as it is a tight fit c Secure the rail with its Phillips screw 4 Repeat Step 3 to install the left inner member A IMPORTANT Depending on your rack type continue with either the Square Holed Rack Installation or Round Figure 7 Attach the Adaptor to the Front Holed Rack Installation oF a Position the adaptor stamped A at the front of the left outer rail end with the graphic label Square Holed Rack installation NOTE Make sure the stamp is at the top and the square l adaptor holes are aligned with the hooks on the outer rail 1 Attach the left outer rail to the rack Figure 5 j amp b Press the adaptor onto the hooks and slide it Tab o upwards until it locks clicks NOTE The rail buttons will snap into the square holes oooooo0o00000 c Repeat Steps a b for the left rear adaptor stamped B m ofogoo00gg000 rd 2 Facing the rack position the left rail in the rack aligning the adaptor holes with the front left rack holes being used Figure 8 on page 3 ODONODONOODOLI L t ooooo0o0oo0o0o0o0o0000008 Hooks
13. sk drives rpn Pener Eerin episod iraa Bonoa Cered Eee ann ierre aoe Erreg Rotational Speed A EI Rotational Speed B Figure 11 Supported Drive Configurations Pee M a Cn Do not include drives with as Ff 2 a different RPMs in the same column E CTE JTE E Canana Maranan eis Kaa ara C JC JC JC J lt Drive Blanks Figure 12 Unsupported Drive Configurations 2010 Overland Storage Inc Page 3of6 e Overland recommends grouping columns of drives of the same speed next to each other when possible Installing Drives NOTE Do not remove the disk drives from their carriers Doing so voids the drive warranty Once the unit is in the rack install the drives Initially the top row is empty and the other two rows are filled with drive blanks Remove as many blanks as needed 1 If a drive blank is in the slot where you are about to install a disk drive remove the blank by pressing the lever release button and pulling it out 2 Remove a drive assembly from the packaging 3 Press the button to release the lever 4 With the button on the right position the drive assembly in front of the appropriate bay and slide it in Figure 13 until resistance is felt 5 ae Maeeeeeeeeeeae i Oo e RE OO00000 2 naceseens QQ00000 Loo hAon A O OSO08OC080088 2 siil NOOD D SAN 5 See NZ aoaaa 66 oNN Vooo e gt gaanar a 2 9 OOS 05005059 s CERISE SSRSS L Oo a
Download Pdf Manuals
Related Search