Oster XVSA User's Manual
Contents
1. ually rotated to seat into the machine socket properly Secure the unit to the machine by tightening the pointed thumbscrew in the hole on the top side of the attachment hub Attach the pusher plate XVSP and close and latch the door XVSD before turning the machine on TO ADJUST THICKNESS OF SLICES Stop the machine While you can adjust the thickness of slices with Adjustable Slicer Plate Assembly in position by turning the gray plas tic Adjusting Knob XP1022 accessed through the opening in the rear housing we recommend that you remove the Adjustable Slicer Plate Assembly from the housing and turn the Adjusting Knob while careful ly holding the plate Adjustment Nut Access CAUTION The adjusting nut turns with the shaft and adjust ments should not be attempted unless the power unit is turned off and unplugged Open Door Locking Pin TO REMOVE XASP ADJUSTABLE SLICE PLATE ASSEMBLY FROM HOUSING Open the door all the way and raise the locking pin XP1007 on top of rear of housing and the assembly will be free for removal by pulling outward Open Door Thumb Screw TO REMOVE ATTACHMENT FROM POWER UNIT Loosen thumbscrew on power unit until hub is free for removal from unit PUSHER PLATE REMOVAL Raise the Pusher Plate and slide it out of the slot in the door XVSD OPERATION Thumb Screw 1 Stop the power unit mixer food cutter chopper power drive etc 2 Attach the housing of slicer to t2. BUYER AND SELLER GFE NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIP MENT Example of items not covered under warranty but not limited to just these items Acts of God fire water damage vandalism accident theft Freight damage Improper installation or alteration of equipment Use of generic or after market parts Repairs made by anyone other than a GFE designated servicer Lubrication Expendable wear parts shredder grater plates and S knife Cleaning of equipment Misuse or abuse 0 00 ND Ol Be Nes FOR COMPLETE XVSA XVGA AND SHREDDER PLATE SALES TOLL FREE 1 800 347 5423 FAX 937 299 4147 FOR SPARE PARTS SALES TOLL FREE 1 800 745 6238 FAX 937 290 0585 GLOBE FOOD EQUIPMENT COMPANY PO BOX 3209 DAYTON OHIO 45439 www globeslicers com O if obe
3. or power drive unit and is retained by the pointed thumbscrew that goes through the attach ment hole into the indentation on the neck of the machine DOOR OR HOPPER The front door is a hopper and lever feed design It hinges onto the back case and is held closed with an adjustable latch To remove the front door lift the latch and swing the door open while lifting it from the hinge holes PUSHER PLATE The pusher plate has an integrated handle to push the food into the rotating disc or slicer knife It has pins at both ends of the top and hinges into the front door The pusher plate has a rubber tipped stop screw XP1018 under the handle that can be adjusted to prevent the plate from coming in contact with the plate or blade XVSP PLATE HOLDER WITH SHAFT Shredder plates are available with 3 32 3 16 1 4 5 16 or 1 2 hole sizes These plates have keyhole slots for attaching to shouldered studs on the plate hubs TO INSTALL SHREDDER OR GRATER DISCS Stop the machine Orient the plate with the cutting edge away from the shaft assembly Locate the keyhole slots on the plate and slide the wide part of the slots over the studs on the plate holder When the plate is flush with the holder rotate it clock wise to lock it in position It is possible to loosely assemble the plate to the hub sharp edge out then place it on a work sur face the teeth on the plate will mar a finished table Press down and turn the hub until plate l
4. HING ONLY using mild detergent in warm water These units are NOT DISHWASHER SAFE due to the corrosive nature of commercial detergents which can discolor alu minum and turn it black Rinse in hot clear water and dry immediately It is important that juices be cleaned from the attachments before they dry Note Frequent lubrication with a USDA approved grease is necessary to prevent shaft seizing o 6 When using the adjustable slicer plate make sure it is Adjustment N hrust cleaned frequently to assure easy thickness adjustment w Bearing Occasionally disassemble the slicer plate for a thorough cleaning To do this it is necessary to unscrew the D knurled thrust bearing which has a left hand thread to release the spring Withdraw the knife and shaft assem bly Unscrew the adjusting nut from the plate Use a drop of approved food machinery oil on the shaft and adjust ment threads after cleaning Note After cleaning to prevent damage the thrust bearing must be tightened until sealed against shoulder on shaft Failure to properly reassemble can result in damage to knives shaft and slicer plate Do not clean any of these compo nents in a dishwasher with strong detergents or chemicals Use a USDA approved grease on the shaft for best operation Spring CAUTION Do not permit water or moisture to remain on or in the hub shaft or the rear opening in the hous ing This condition will result in rusting which w
5. Head Machine Screw 6 for hub Knife Lock Screw Fiber gasket Plate Holder Assembly Complete Brass Collar with set screw Set Screw for Collar Stud for Plate Holders 3 32 S S Shredder Plate 3 16 S S Shredder Plate 1 4 S S Shredder Plate 5 16 S S Shredder Plate 1 2 S S Shredder Plate S S Grater Plate XASP ADJUSTABLE SLICER PLATE XP571 XP1571 XP1022 XP1023 XP1024 XVSD DOOR XP1012 XP1013 XP1014 XVSP PUSHER PLATE XP1017 XP1018 XP1035 XP1036 S Knife only S Knife and Shaft Assembly Knife Adjusting Nut Gray Plastic Tension Spring Bronze Lock Nut or Thrust Bearing Upper Hinge Pin long Lower Hinge Pin short Latch Pin Stop Nut Stop Screw Ball End Hinge Pin Hinge Pin Shredder and Grater Plate Hole Sizes with Typical Applications 1 2 5 16 3 16 3 32 Universal Food Shredder Shredder Shredder Shredder Product Plate Cole Slaw Bread Crumbs Soft Cheese For Pizza Carrots For Coloring Cheese For Tacos Hard Cheese SS Grater Plate gt lt C 3 32 3 16 1 4 5 16 1 2 For Hard Cheese only WARNING AWAY FROM MOVING PARTS Globe LIMITED XVSA XVGA ATTACHMENT WARRANTY Globe Food Equipment Company GFE warrants to the original purchaser of new equipment that said equipment when installed in accordance with our instructions within North America and subjected to normal use is free from defects in material or workmanship for a period
6. INSTRUCTIONS FOR OPERATION AND CARE XVGA GRATER SHREDDER AND XVSA SLICER ATTACHMENTS Our versatile grater shredder attachments can be used to grate and shred cheeses raw vegetables nuts breadcrumbs etc depending on the plate selected Our S S plates are available with 3 32 3 16 1 4 5 16 or 1 2 size holes and a special grating plate for breadcrumbs amp hard cheeses A plate holder with shaft and one 3 16 plate are included with the XVGA attachment Our slicer attachments can be used for slicing potatoes from 1 16 to 5 8 thickness cut ting vegetables for salads and coleslaw or for slicing fruits and nuts An adjustable slicer plate with shaft are included with the XVSA attachment WARNING There are sharp rotating knives behind the front door keep hands out of hopper and use a feed pusher or stomper to push product into the hopper do not use your fingers Always stop power unit before opening front for changing cleaning or servicing anything on this unit Only trained and qualified persons 18 years and older should use these attachments These attachments are made up of the following four basic components 1 XVSH Housing 2 XVSD Front Door or Hopper 3 XVSP Pusher Plate 4 Plate Holder or Adjustable Slicer Plate units 1 Adjustable Slicer Shaft XASP with S S S knife 2 Shredder Plate Holder XPH HOUSING OR BACK CASE The housing or back case mounts into the attachment socket of a mixer food cutter
7. he attachment socket of the companion machine with the thumbscrew Select the grater shredder or slicer assembly to be used Lift the locking pin and insert the plate and shaft assem bly into the drive position Release the locking pin Set the slice adjustment if used to the proper thickness Adjustment Nut CLEANING 4 Drop the hinge pins of the front door into the holes in the housing j 5 Close the slicer front door and fasten the latch 6 Start the machine Set at a speed to produce the best product see machine manual 7 Raise the pusher plate lever 8 Place the food to be sliced in the hopper and gently press down on the pusher plate lever c Note Too much pressure crushes the food and causes AUTION Keep Hands out of Hopper use a irregularity in the slices Large items may have to stomper or food pusher be cut down to fit into the hopper MAINTENANCE INSTRUCTIONS Pusher Plate Lever 1 Stop the power unit mixer food cutter power drive etc 2 Release the latch and remove the front door 3 Lift the locking pin and withdraw the shredding or slicing unit from the housing a 4 The shredder and grater plates can be easily removed from e E a P the plate hub by rotating plate counter clockwise to release vi the keyhole slot from the studs CAUTION These plates are sharp and must be handled with care 5 All components of these attachments may be cleaned by HAND WAS
8. ill eventually destroy the rear end components and shaft and void the factory warranty KNIFE SHARPENING Occasional touching up along the edges of the knife with a honing stone will keep cutting operations at peak performance PUSHER PLATE STOP Frequently check that the pusher plate does not hit the grater plate holder or knife shaft assembly The Pusher Plate Stop XP1018 can be adjusted to avoid touching the internal moving parts With proper care and maintenance your Vegetable Grater Shredder Slicer Attachment will provide you with many years of performance XPH Plate Holder XP1030 z XP1026A Plat XP1026 Brass D ee XP1010 XP1012 i s XP1009 XVSP 4 7 lt lt Pusher Plate D 2 XP1035 XVSD S NS S eee XP1008 i XP1005A XP1014 i veii J es Housing CoR i XP1005 XP1017 iN D 7 XVSH Housi L4 ousing XP1018 XP1013 s XP1024 Brass XVSD Door tansy with Hopper Opening xes XP1022 Plastic Knife only XP1571 Knife and Shaft XASP Adjustable Slicer Plate Assembly WARNING KEEP FINGERS AND HANDS AWAY FROM MOVING PARTS D o XVSH HOUSING XVSH XP1004 XP1005 XP1005A XP1007 XP1008 XP1009 XP1010 XP1011 XPH PLATE HOLDER XPH XP1026 XP1026A XP1030 XSP332 XSP316 XSP14 XSP516 XSP12 XGP PART NUMBER LISTING Housing size 12 Threaded Hex Pin for housing latch Latch with setscrew Latch setscrew only Shaft Lock knob top Housing Hub with locating pin six holes Flat
9. ocks into place The sharp teeth should face out on the holder To detach the plate from the hub reverse the installation procedure A safe method is to use protective gloves and press the palm of one hand against the plate to rotate it Note The plates are slightly bent to provide holding pressure when in position Keyhole Slots SHREDDER PLATE The coarse plates are normally used for making chopped slaw cutting vegetables for soup stock salad blends or hash brown potatoes The medium and finer plates are for fine shredding of carrots beets turnips etc and for salads See our application chart at the end of these instructions GRATER PLATE The grater plate may be used for crumbling hard cheese or grating hard vegetables i Locking Pin e TO INSTALL XPH PLATE HOLDER ASSEMBLY Stop the machine With door open pull the locking pin XP1007 up and insert XPH until the square end of the shaft fits snugly into the power unit Then release the locking pin to hold the XPH in proper position Open Door ADJUSTABLE SLICER PLATE ASSEMBLY amp INSTALLATION Turn off and unplug the machine Adjust the slicing thickness from Adjustment approximately 1 16 to 5 8 by turning the gray plastic adjusting nut A XP1022 Lift the silver locking pin XP1007 on the top of the rear of the housing and open the front door and slide the slicer unit back into E D OBEE operating position The square end of the shaft may have to be man
10. of 1 year from invoice date The XVSA Vegetable Slicing Attachment and XVGA Shredder Grater Attachment have a 1 year replacement warranty There is no labor warranty for mixer attachments THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED GFE EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FIT NESS FOR A PARTICULAR PURPOSE GFE S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT WHICH PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD All repairs pursuant to this Warranty will be performed by an Authorized Designated GFE Service Location during normal working hours IN NO EVENT SHALL GFE BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY INCLUDING WITHOUT LIMITATION LOSS OF PROPERTY PERSONAL INJURY LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC LOSSES OR STATUTORY OR EXEMPLARY DAMAGES WHETHER IN NEGLI GENCE WARRANTY STRICT LIABILITY OR OTHERWISE This Warranty is given only to the first purchaser from a retail dealer No warranty is given to subsequent transferees This Warranty does not cover product failures caused by failure to maintain neglect abuse damage due to excess water fire normal wear improper set up and use Periodic maintenance is not covered THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE
Download Pdf Manuals
Related Search