Home

Orion Car Audio XTRPRO124 User's Manual

1. l Polypropylene dust cap moisture and UV resistant 2 Oversized NBR Nitrile butadiene Rubber surround for linear controlled long excursion 3 Paper cone moisture and UV resistant 4 Custom cast aluminum frame 5 Vented Aluminum voice coil former 2 5 voice coil former 6 8mm steel front plate 7 Large 2 stack ceramic magnets 8 8mm steel back plate pole piece T yoke assembly 9 1 125 vent Part of the enhanced voice coil cooling system forced convection 10 PVC magnet protector 11 High temperature Copper dual 2 ohm or dual 4 ohm voice coil 12 Venting in voice coil former Part of the enhanced voice coil cooling system forced convection 13 Dual Interlaced Conex spider with stitched and looped tinsel leads attached 14 Custom terminal blocks 15 ABS Trim Ring O 2008 directed electronics all rights reserved WIRING CONFIGURATIONS Series One Speaker dual 2 ohm voice coils One dual 2 ohm voice coil woofer with voice coils in connected in series results in a 4 ohm load to the amplifier Figure 2 Figura 2 Abbildung 2 1 Connect the woofer in series by connecting the negative of one terminal to the positive terminal of the other coil 2 Wire the positive terminal of the first coil to the positive terminal on the amplifier Wire the negative termi
2. Bassreflex Tuningfrequenz Hz Bassreflex Fl chen quivalenz Zoll L nge der Bassreflex ffnung Zoll Daten k nnen ohne vorherige Ank ndigung ge ndert werden GEHAUSEDETAILS 1 Die aufgelisteten Parameter gelten nur f r konventionelle Anwendungen Um weitere Hilfe zu erhalten rufen Sie bitte den Tech Audio Support an 2 Es wird empfohlen 1 9 cm dicke Faserplatten zu verwenden 3 Die empfohlenen Geh usegr Ben sind NETTO Volumen wobei Lautsprecher und ffnungshub in das Geh usevolumen einberechnet sind Sie m ssen diese Volumen nicht hinzuz hlen um das BRUTTO Geh usevolumen zu erhalten HINWEISE Aufgrund der hohen Belastbarkeit und gro en Auslenkung dieser Tieft ner wurden die Thiele Small Parameter unter Verwendung eines Klippel Analysesystems berechnet und gemessen kk Das Verst rkungs Bandbreitenprodukt EBP wird durch folgende Formel ermittelt Fs Qes EBP EBP Werte von 50 und darunter bedeuten dass ein geschlossenes Geh use besser ist 50 bis 90 bedeuten dass ein Subwoofer 2008 directed electronics Alle Rechte vorbehalten 51 angebracht w re und bei 90 und mehr empfehlen wir ein Bassreflexgeh use Subsonic Filter sollten immer verwendet und speziell an Bassreflexgeh use angepasst werden ERL UTERUNG DER GEH USEDATEN Es gibt viele verschiedene Faktoren die den besten Geh usetyp f r Sie bzw Ihr Fahrzeug bestimmen Unten finden Sie einig
3. larghezza b spessore 1 anteriore 1 posteriore altezza a larghezza d spessore 2 laterali altezza a profondit c spessore Montaggio del driver Montaggio anteriore 63 Legenda relativa alla cassa ventilata vedi pagine 19 21 e 23 per le misure Propriet della cassa Descrizione Tipo cassa ventilata Vb Forma prisma quadrato totale Fb QL F3 Riempitivo A 7 C pos Superiore e inferiore Anteriore e posteriore Laterali 64 Parametri della cassa Il Aperture N di aperture Forma apertura circolare Estremit apertura una a filo Dv Lv Dimensioni esterne A B C Dimensioni interne A B C Spessore delle pareti Anteriore Laterali Parti della cassa Forma della cassa prisma quadrato 1 superiore 1 inferiore profondit c larghezza b spessore 1 anteriore 1 posteriore altezza a larghezza d spessore 2 laterali altezza a profondit c Spessore Montaggio del driver Montaggio anteriore Parti apertura 1 tubo diametro esterno e diametro interno g lunghezza h 2008 directed electronics tutti i diritti riservati PORTUGU S INSTALACAO O desempenho dos subwoofers XTRPRO diretamente proporcional qualidade da instala o O cuidado durante o processo de instala o ser recompensado com
4. Partes de la caja Forma de la caja prisma cuadrado 1 parte de arriba 1 parte de abajo fondo c ancho b grosor 1 parte de adelante 1 parte de atr s alto a ancho d grosor 2 lados alto a fondo c grosor Montaje del excitador Montaje adelante 2008 directed electronics Reservados todos los derechos 43 Traducci n del diagrama de la caja ventilada las medidas se encuentran en las p gi nas 19 21 y 23 Propiedades de la caja Descripci n Tipo caja con respiradero Forma prisma cuadrado gt i Parte de arriba i y parte de abajo Par metros de la caja Respiraderos Vb V total Fb QL F3 Fill Parte de adelante y parte de atr s 44 N de respiraderos Forma del respiradero redondo Extremos del respiradero uno al ras Dv Lv Dimensiones externas A B C Dimensiones internas A B C Grosor de la pared Parte de adelante Lados Partes de la caja Forma de la caja prisma cuadrado 1 parte de arriba 1 parte de abajo fondo c ancho b grosor 1 parte de adelante 1 parte de atr s alto a ancho d grosor 2 lados alto a fondo c grosor Montaje del excitador Montaje adelante Partes del respiradero 1 conducto di metro externo e di metro interno g largo h 2008 directed electronics Reservad
5. 2 Raccordez les deux bornes positives du haut parleur de graves la borne positive de l amplificateur Raccordez les deux bornes n gatives du haut parleur de graves la borne n gative de l amplificateur Parall le Deux haut parleurs deux bobines mobiles de 4 ohms Voir la figure 5 la page 6 Deux haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 4 ohms raccord es en parall le constituent une charge de 1 ohm pour l amplificateur 1 Configurez le haut parleur de graves en parall le en raccordant entre elles les quatre bornes positives et les quatre bornes n gatives 2 Raccordez les bornes positives des haut parleurs de graves la borne positive 2008 directed electronics Tous droits r serv s 27 de l amplificateur Raccordez les bornes n gatives des haut parleurs de graves la borne n gative de l amplificateur S rie parall le Deux haut parleurs deux bobines mobiles de 2 ohms Voir la figure 6 la page 7 Remarque V rifiez que le c blage du haut parleur de graves est conforme l illustration avec la borne n gative de la premi re bobine du haut parleur de graves reli e la borne positive de la seconde bobine Deux haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 2 ohms raccord es en s rie constituent une charge de 2 ohms pour l amplificateur 1 Configurez chaque haut parleur d
6. 3 545 x 3 545 Port length inches 11 26 5 42 5 42 Specifications are subject to change without notice 2008 directed electronics all rights reserved 15 Enclosure Details 1 Parameters listed are for conventional applications only for further help please call Audio Tech Support 2 At least 0 75 MDF Medium Density Fiberboard is recommend for any XTRPRO enclosure 3 Recommended enclosures are NET box volumes speaker and port displacement are calculated into the volume of the enclosure you will not need to add these volumes to calculate GROSS volume for the enclosure Notes kk Due to the high power capabilities and long excursion of the XTRPRO woofers the Thiele Small Parameters were calculated and measured using a Klippel analyzer system Energy Bandwidth Product EBP is determined by the following formula Fs Qes EBP EBP values of 50 and lower suggest a sealed enclosure is best 50 to90 means the subwoofers versatile and 90 and above mean vented Enclosure is recommended Subsonic filter should always be used and adjusted specifically for vented box Dimensions inches mm Dimensions Dimensioni pollici millimetri Dimens es polegadas mm designs i Da re Le A Bot A B Y l RES J Le ma D gt Le E gt Figure 13 Figura 13 Abbildung 13 XTRPRO102 XTRPRO104 XTRPRO122 XTRPRO124 XTRPRO152 XTRPRO154
7. de la seconde 2 Raccordez la borne positive de la premi re bobine de chaque haut parleur de graves la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine de chaque haut parleur de graves la borne n gative de l amplificateur S rie parall le Quatre haut parleurs deux bobines mobiles de 2 ohms Voir la figure 10 la page 11 Remarque V rifiez que le c blage du haut parleur de graves est conforme l illustration avec la borne n gative de la premi re bobine du haut parleur de graves reli e la borne positive de la seconde bobine Quatre haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 2 ohms raccord es en s rie constituent une charge de 1 ohm pour l amplificateur 1 Configurez chaque haut parleur de graves en s rie en raccordant la borne n gative de la premi re bobine la borne positive de la seconde 2 Raccordez la borne positive de la premi re bobine de chaque haut parleur de graves la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine de chaque haut parleur de graves la borne n gative de l amplificateur 2 amplificateurs Un haut parleur deux bobines mobiles de 2 ohms Voir la figure 11 la page 12 Un haut parleur de graves deux bobines mobiles de 2 ohms raccord es chacune un amplificateur distinct constitue une charge de 2 ohms pour chaque amp
8. po mm Dimensiones plg mm Abmessungen Zoll mm A 5 87 149 5 87 149 6 46 164 6 46 164 7 49 190 7 49 190 B 2 84 72 2 84 72 2 84 72 2 84 72 2 84 72 2 84 72 a 6 15 156 6 15 156 6 15 156 6 15 156 6 15 156 6 15 156 D 8 87 225 8 87 225 10 91 277 10 91 277 13 87 352 13 87 352 E 10 24 260 10 24 260 12 29 312 12 29 312 15 29 388 15 29 388 16 2008 directed electronics all rights reserved Explanation of Enclosure Specifications There are many different factors that help determine the best style of enclosure for you or your vehicle Listed below are some factors that should be considered The size of the enclosure is directly proportional to the efficiency and power handling of that speaker A woofer in a smaller enclosure will handle more power than the same woofer in a larger enclosure The exact opposite is true for efficiency a larger enclosure will play lower frequencies at a louder volume with less power than a smaller enclosure The following will explain differences in sealed enclosures A large enclosure is best suited if you have smaller amounts of power 25 to 50 of speaker s power handling have a larger vehicle or looking for greater output While the smaller enclosure should be utilized if you have recommended power 50 to 100 of speaker s rated power handling have a smaller high gain vehicle or are looking for more accurate sound reproduction A smaller sealed enclosure will yield more co
9. tutti i diritti riservati 59 separato applica un carico di 4 ohm a ciascun amplificatore 1 Collegare una delle bobine mobili del woofer al primo amplificatore collegandone il terminale positivo e quello negativo rispettivamente al terminale positivo e a quello negativo dell amplificatore stesso Collegare l altra bobina mobile del woofer al secondo amplificatore collegandone il terminale positivo e quello negativo rispettivamente al terminale positivo e a quello negativo dell amplificatore stesso DATI TECNICI Per i dati tecnici dettagliati vedere alle pagine 14 e 15 60 Modello Codice XTRPRO Dimensioni Parametri Thiele Small Fs freq di risonanza in aria libera Hz Vas volume equivalente di cedevolezza cu ft Vas volume equivalente di cedevolezza litri Qms Q meccanico Qes Q elettrico Qts Q totale driver Re resistenza in c c ohm Z impedenza nominale ohm Le induttanza mH Efficienza 1 W a 1 M dB Efficienza 2 86 V a 1 M dB Xmax escursione lineare monodirezionale in Xmax escursione lineare monodirezionale mm Pe potenza elettrica continua watt Potenza di picco acustica watt Mms massa meccanica mobile totale grammi Cms cedevolezza meccanica mm N BI fattore di forza elettromeccanico Tem Sd superficie radiante effettiva cm quadrati Sd superficie radian
10. Hz Vas conformit quivalente pieds cubes Vas conformit quivalente litres Qms Q m canique Qes Q lectrique Qts Q total haut parleur Re r sistance c c ohms Z imp dance nominale ohms Le inductance mH Rendement 1W 1 m dB Rendement 2 86 V 1 m dB Xmax course lin aire dans un sens pouces Xmax course lin aire dans un sens mm Pe puissance continue admissible watts Puissance cr te admissible musique watts Mms masse mobile totale grammes Cms conformit m canique mm N BI intensit magn tique moteur tesla m tres 30 2008 directed electronics Tous droits r serv s Sd surface effective de rayonnement cm2 Sd surface effective de rayonnement m2 Sd surface effective de rayonnement pouces carr s Plage de fr quence Hz Facteur d efficacit EBP Encombrement du haut parleur Volume du haut parleur pieds cubes Diam tre du trou de montage pouces mm Profondeur de montage pouces mm Poids de l aimant onces Diam tre du saladier pouces mm Caissons recommand s Caisson clos courant pieds cubes Caisson vent accord pieds cubes Fr quence d accord de l vent Hz Carr quivalent l vent pouces Longueur de l vent pouces Sp cifications sujettes changemen
11. 406 mm C 14 24 in 362 mm Internal Dimensions A 14 5 in 368 mm A B 14 5 in 368 mm A C 12 74 in 324 mm C Wall Thickness Front 0 75 in 19 mm lt B Side 0 75 in 19 mm Box Parts Box Shape Square Prism 1 Top 1 Bottom depth c 14 24 in 362 mm width b 16 in 406 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 14 5 in 368 mm lt d gt s c di width d 14 5 368 mm thickness 0 75 in 19 mm 2 Sides i Front amp height a 14 5 in 368 mm a Back depth c 14 24 in 362 mm i thickness 0 75 in 19 mm Driver Mounting Sa 1 Mounting Front Abbildung 16 20 2008 directed electronics all rights reserved XTRPRO122 amp 124 Vented Enclosure Recommendations Box Properties Description Box Parameters Vents Type Vented Box Vb 1 5 cu ft No of Vents 1 Shape Prism Square V total 1 637 cu ft Vent shape round Fb u 40 Hz Vent ends one flush QL 6 886 Dv 4 in 102 mm F3 32 19 Hz Lv 11 26 in 286 mm Fill none A Lea E External Dimensions igura A Abbildung 17 A 13 5 in 343 mm B 18 5 in 470 mm C 15 36 in 390 mm Internal Dimensions A 12 in 305 mm B 17 in 432 mm A C 13 86 in 352 mm C Wall Thickness Front 0 75 in 19 mm _B gt Side 0 75 in 19 mm gt Box Parts Box Shape Square Prism 1 Top 1 Bottom Bo
12. 46 OA 7 AL 14 13 12 A JO 3 6 mato Feuchtigkeits und UV best ndige Polypropylen Abdeckung Extra groBe Sicke aus NBR Nitrilgummi f r linear kontrollierten Langhub Feuchtigkeits und UV best ndige Papiermembran Spezieller Rahmen aus Aluminiumguss Aluminium Schwingspulentr ger mit ffnungen 2 5 Zoll Schwingspulentr ger 8 mm dickes vorderes Abdeckblech GroBe Double Stack Keramikmagneten 8 mm dickes hinteres Abdeckblech Polplatten T St ck 1 125 Zoll ffnung Teil des verbesserten Schwingspulen K hlsystems Zwangs Konvektion PVC Magnetschutz Hochtemperatur Kupferschwingspule doppelt 2 Ohm oder doppelt 4 Ohm Bel ftung des Schwingspulentr gers Teil des verbesserten Schwingspulen K hlsystems Zwangs Konvektion Doppelte verkn pfte Conex Zentriermembran mit gehefteten und geschleiften Zuleitungslitzen Spezielle Anschlussleisten ABS Blendenring 2008 directed electronics Alle Rechte vorbehalten SCHALTKONFIGURATIONEN Reihe Ein Lautsprecher Doppelte 2 Ohm Schwingspulen Siehe Abbildung 2 auf Seite 4 Ein Tieft ner mit doppelten 2 Ohm Schwingspulen bei dem die Schwingspulen in Reihe geschaltet sind Lastwiderstand von 4 Ohm am Verst rker 1 SchlieBen Sie den Tieft ner in Reihe an indem Sie das negative Terminal der einen
13. 89 5 49 5 93 Qes Q electrical 0 66 0 67 0 84 Qts total driver Q 0 59 0 61 0 73 Re DC resistance ohms 7 1 4 2 7 2 Z nominal impedance ohms 8 4 8 Le inductance mh 2 82 1 96 3 05 Efficiency 1W 1M dB 84 4 86 3 85 9 Efficiency 2 86 V 1M dB 85 1 89 2 86 9 Xmax one way linear excursion in 0 680 0 680 0 680 Xmax one way linear excursion mm 17 25 17 25 17 25 Pe continuous power handling watts 500 500 500 Peak power handling music watts 1000 1000 1000 Mms total moving mass grams 214 58 405 83 290 58 Cms mechanical compliance mm N 0 113 0 114 0 106 BI motor strength Tesla M 21 62 16 57 21 18 Sd effective radiating area sq cm 471 435 779 311 779 311 Sd effective radiating area sq m 0 047 0 078 0 078 Sd effective radiating area sq in 73 100 120 839 120 839 Frequency range Hz 32 3 500 23 4 500 28 7 500 Energy Bandwidth Product EBP 49 35 34 Driver Physical Dimension Speaker Displacement cu ft 0 091 0 143 0 143 Mounting hole diameter inches mm 10 91 277 13 85 352 13 85 352 Mounting depth inches mm 6 46 164 7 48 190 7 48 190 Magnet Weight Oz 96 00 96 00 96 00 Basket diameter inches mm 12 28 312 15 27 388 15 27 388 Recommended Enclosures Typical sealed enclosure cu ft 1 50 2 00 2 00 Vented enclosure cu ft 1 50 3 00 3 00 Port tuning frequency Hz 40 00 36 00 36 00 Port diameter inside inches 4 00 4 00 4 00 Port square equivalent inches 3 545 x 3 545 3 545 x 3 545
14. Connect the speaker in parallel by connecting the four positive terminals together and the four negative terminals together 2 Wire the positive terminals of the woofers to the positive terminal on the amplifier Wire the negative terminals of the woofers to the negative terminal on the amplifier 6 2008 directed electronics all rights reserved Series Parallel Two Speakers dual 2 ohm voice coils Note Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil Two dual 2 ohm voice coil woofers with voice coils in series and then parallel the two series woofers results in a 2 ohm load to the amplifier Figure 6 Figura 6 Abbildung 6 1 Connect each woofer in series by connecting the negative of the first coil to the positive terminal of the second coil 2 Wire the positive terminal of the first coil on each woofer to the positive terminal on the amplifier Wire the negative terminal of the second coil on each woofer to the negative terminal on the amplifier 2008 directed electronics all rights reserved 7 Series Parallel Three Speakers dual 4 ohm voice coils Note Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection
15. INSTALLATION Les performances de ces haut parleurs de graves XTRPRO sont directement li es la qualit de l installation Les pr cautions prises lors de l installation se traduiront par des ann es de bon fonctionnement Si vous doutez de pouvoir obtenir une bonne installation veuillez demander l assistance technique d un revendeur Orion agr Les revendeurs Orion sont des professionnels comp tents sp cialis s capables d obtenir les meilleures performances des syst mes Orion Si vous d cidez d installer vous m me ce syst me de haut parleurs veuillez lire toute la section relative aux caissons clos et aux caissons vent accord avant de commencer l installation CHOIX DES EMPLACEMENTS DE MONTAGE DES HAUT PARLEURS Le choix des emplacements de montage des haut parleurs a une tr s grande influence sur la qualit sonore du syst me Pour choisir les emplacements r pondant le mieux aux besoins de l utilisateur de nombreux facteurs doivent tre pris en compte Il faut qu il y ait suffisamment de place pour y placer les haut parleurs V rifiez que l emplacement choisi est compatible avec le fonctionnement m canique et lectrique du v hicule Le choix des meilleurs emplacements pour les haut parleurs est conditionn par l esth tisme et le d cor int rieur du v hicule En g n ral les haut parleurs de graves sont install s dans le coffre le si ge arri re ou l arri re du v hicule 2008 directed electroni
16. Los lugares escogidos deben ser lo suficientemente grandes como para que quepan los altavoces Es necesario que en la ubicaci n escogida no se afecte ninguna operaci n mec nica o el ctrica del veh culo Determinar la mejor ubicaci n de los altavoces depende de sus necesidades cosm ticas y del interior del veh culo Por lo general los woofers se instalan en el maletero el asiento trasero o la parte de atr s del veh culo 2008 directed electronics Reservados todos los derechos 35 CARACTERISTICAS O OA 7 AL 14 E i 5 12 metered o o pnan 0000000000 0000000000 11 z 6 q U 10 9 8 1 Tapa de polipropileno contra el polvo resistente a la humedad y a los rayos ultravioleta 2 Envolvente de Goma de Butadieno de Nitrilo NBR paragrandesdesplazamientos lineales controlados 3 Cono de papel resistente a la humedad y los rayos ultravioleta Armaz n de aluminio troquelado a la medida Formador de bobina ac stica de aluminio ventilado formador de bobina ac stica de 2 5 plg 6 Plancha delantera de acero de 8 mm 7 2 imanes grandes de cer mica de 2 pilas 8 Unidad de yugo en T de pieza polar y plancha trasera de acero de 8 mm 9 Respiradero de 1 125 plg Parte del sistema mejorado de enfriamiento de bobina ac stica con
17. Sie das negative Terminal der ersten Schwingspule mit dem positiven Terminal der zweiten Spule verbinden 2 Verbinden Sie die positiven Terminals der ersten Schwingspule am jeweiligen Tieft ner mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der zweiten Schwingspule am jeweiligen Tieft ner mit dem negativen Terminal am Verst rker Reihe Parallel Vier Lautsprecher doppelte 2 Ohm Schwingspulen Siehe Abbildung 10 auf Seite 11 Hinweis Stellen Sie sicher dass die Tieft neranschl sse wie gezeigtvorgenommen wurden wobei der negative Anschluss an der ersten Tieft ner Schwingspule mit dem positiven Anschluss an der zweiten Tieft ner Schwingspule verbunden ist Vier Tieft ner mit doppelten 2 Ohm Schwingspulen sollten so angeschlossen werden dass die Schwingspulen an jedem Tieft ner in Reihe geschaltet und dann die vier Tieft ner parallel geschaltet werden Lastwiderstand von 1 Ohm am Verst rker 1 SchlieBen Sie jeden Tieft ner in Reihe an indem Sie das negative Terminal der ersten Schwingspule mit dem positiven Terminal der zweiten Spule verbinden 2 Verbinden Sie die positiven Terminals der ersten Schwingspule am jeweiligen Tieft ner mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der zweiten Schwingspule am jeweiligen Tieft ner mit dem negativen Terminal am Verst rker 2008 directed electronics Alle Rechte v
18. along with the required proof of installation the bill of sale or other dated proof of purchase and the consumer s contact information If the Unit is installed by anyone other than an authorized Directed dealer the warranty period will be one year from the date of purchase This warranty is non transferable and does not apply to any Unit that has been modified or used in a manner contrary to its intended purpose and does not cover damage to the Unit caused by installation or removal of the Unit During this one year period there will be no charge for the repair or replacement PROVIDED the Unit is returned to Directed shipping pre paid along with the bill of sale or other dated proof of purchase and the consumer s contact information This warranty is void if the product has been damaged by accident or unreasonable use neglect improper service or other causes not arising out of defects in materials or construction This warranty does not cover the elimination of externally generated static or noise or the correction of antenna problems or weak reception damage to speakers accessories electri cal systems cosmetic damage or damage due to negligence misuse failure to follow operating instructions accidental spills or customer applied cleaners damage due to environmental causes such as floods airborne fallout chemicals salt hail lightning or extreme temperatures damage due to accidents road hazards fire theft loss or vandalism damage d
19. anos de satisfa o com o desempenho Caso n o esteja certo quanto sua capacidade para fazer a instala o consulte o revendedor autorizado local da Orion para obter assist ncia t cnica Os revendedores da Orion s o profissionais capacitados dedicados a maximizar o desempenho de seu sistema Caso decida instalar este sistema de alto falantes por conta pr pria leia toda a se o sobre caixas ac sticas seladas e ventiladas antes de comegar a instalac o DETERMINA O DOS LOCAIS DE INSTALA O DOS ALTOS FALANTES A sele o dos locais corretos para instala o dos alto falantes o fator que mais influenciar a qualidade do som produzido pelo sistema necess rio considerar v rios aspectos ao escolher os locais mais adequados s suas necessidades Os locais de instala o devem ser grandes o suficiente para acomodar os alto falantes e necess rio cuidado para assegurar que os locais escolhidos n o afetem nenhuma das fun es mec nicas ou el tricas do ve culo A determina o dos melhores locais para a instala o dos alto falantes depender de suas necessidades est ticas e do interior do ve culo Geralmente os woofers s o instalados no porta malas banco traseiro ou painel traseiro do ve culo 2008 directed electronics Todos os direitos reservados 65 CARACTERISTICAS 66 O OA 7 AL 14 0000000000 0000000000 5
20. carga de 2 67 ohm ao amplificador 1 Conecte cada woofer em s rie unindo o terminal negativo da primeira bobina ao terminal positivo da segunda bobina 2 Conecte o terminal positivo da primeira bobina de cada woofer ao terminal positivo do amplificador Conecte o terminal negativo da segunda bobina de cada woofer ao terminal negativo do amplificador S rie Paralela Tr s alto falantes duas bobinas de 2 ohm Ver figura 8 na p gina 9 Nota Verifique e certifique se de que os cabos dos woofers estejam conectados como mostrado com o terminal negativo da bobina do primeiro woofer conectado ao terminal positivo da bobina do segundo woofer Tr s woofers com duas bobinas m veis de 2 ohm com as bobinas de cada woofer conectadas em s rie e em seguida os tr s woofers em paralelo resultam em uma carga de 1 33 ohm ao amplificador 1 Conecte cada woofer em s rie unindo o terminal negativo da primeira bobina ao terminal positivo da segunda bobina 2 Conecte o terminal positivo da primeira bobina de cada woofer ao terminal 68 2008 directed electronics Todos os direitos reservados positivo do amplificador Conecte o terminal negativo da segunda bobina de cada woofer ao terminal negativo do amplificador S rie Paralela Quatro alto falantes duas bobinas de 4 ohm Ver figura 9 na p gina 10 Nota Verifique e certifique se de que os cabos dos woofers estejam conectados como mostr
21. de cada woofer ao terminal negativo do amplificador Dois amplificadores Um alto falante duas bobinas de 2 ohm Ver figura 11 na p gina 12 Um woofer com duas bobinas m veis de 2 ohm com cada bobina conectada a um amplificador resultando em uma carga de 2 ohm a cada amplificador 1 Conecte uma das bobinas m veis do alto falante ao primeiro amplificador unindo o terminal positivo e o terminal negativo do alto falante aos respectivos terminais positivo e negativo do primeiro amplificador 2 Conecte as demais bobinas m veis do alto falante ao segundo amplificador unindo o terminal positivo e o terminal negativo do alto falante aos respectivos terminais positivo e negativo do segundo amplificador 2008 directed electronics Todos os direitos reservados 69 Dois amplificadores Um alto falante duas bobinas m veis de 4 ohm Ver figura 12 na p gina 13 Um woofer com duas bobinas m veis de 4 ohm com cada bobina conectada a um amplificador resultando em uma carga de 4 ohm a cada amplificador 1 Conecte uma das bobinas m veis do alto falante ao primeiro amplificador unindo o terminal positivo e o terminal negativo do alto falante aos respectivos terminais positivo e negativo do primeiro amplificador 2 Conecte as demais bobinas m veis do alto falante ao segundo amplificador unindo o terminal positivo e o terminal negativo do alto falante aos respectivos terminais pos
22. la figura 6 en la p gina 7 Nota Verifique y aseg rese de que el cableado del woofer es como se muestra la terminal negativa de la bobina de un woofer conectada a la terminal positiva de la bobina del otro woofer Dos woofers con dos bobinas ac sticas de 2 Q cada uno las bobinas ac sticas en serie y los 2 woofers en paralelo producen una carga de 2 Q en el amplificador 1 Conecte cada woofer en serie conectando la terminal negativa de una bobina a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina de cada woofer a la terminal positiva del amplificador Conecte la terminal negativa de la segunda bobina de cada woofer a la terminal negativa del amplificador En serie paralelo tres altavoces dos bobinas ac sticas de 4 O cada uno Vea la figura 7 en la p gina 8 Nota Verifique y aseg rese de que el cableado del woofer es como se muestra la terminal negativa de la bobina de un woofer conectada a la terminal positiva de la bobina del otro woofer Tres woofers con dos bobinas ac sticas de 4 2 cada uno las bobinas ac sticas en serie y los 3 woofers en paralelo producen una carga de 2 67 Q en el amplificador 1 Conecte cada woofer en serie conectando la terminal negativa de una bobina a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina de cada woofer a la terminal positiva del amplificador Conecte la ter
23. las terminales positivas del woofer a la terminal positiva del amplificador Conecte las terminales negativas del woofer a la terminal negativa del amplificador En paralelo un altavoz dos bobinas ac sticas de 4 Vea la figura 4 en la p gina 5 Un woofer con 2 bobinas ac sticas de 4 Q y las bobinas ac sticas en paralelo produce una carga de 2 Q en el amplificador 1 Conecte el woofer en paralelo conectando las dos terminales positivas entre s y las dos terminales negativas entre s 2 Conecte las terminales positivas del woofer a la terminal positiva del amplificador Conecte las terminales negativas del woofer a la terminal negativa del amplificador En paralelo dos altavoces dos bobinas ac sticas de 4 cada uno Vea la figura 5 en la p gina 6 Dos woofers con dos bobinas ac sticas de 4 Q cada uno las bobinas ac sticas en paralelo y los woofers en paralelo producen una carga de 1 Q en el amplificador 1 Conecte los woofers en paralelo conectando las cuatro terminales positivas entre s y las cuatro terminales negativas entre s 2 Conecte las terminales positivas de los woofers a la terminal positiva del amplificador Conecte las terminales negativas de los woofers a la terminal 2008 directed electronics Reservados todos los derechos 37 negativa del amplificador En serie paralelo dos altavoces dos bobinas ac sticas de 2 O cada uno Vea
24. mm thickness 0 75 in 19 mm E uni D Driver Mounting igure De Figura 18 Mounting Front Abbildung 18 22 O 2008 directed electronics all rights reserved XTRPRO152 amp 154 Vented Enclosure Recommendations Box Properties Description Box Parameters Vents Type Vented Box Vb 3 cu ft No of Vents 1 Shape Prism Square V total 3 116 cu ft Vent shape round Fb 36 Hz Vent ends one flush QL 5 Dv 4 in 102 mm F3 29 7 Hz Lv 5 422 in 138 mm Fill none Figure 19 Figura 19 External Dimensions Abbildung 19 A 18 5 in 470 mm B 23 5 in 597 mm C 15 9 in 404 mm Internal Dimensions A 17 in 432 mm B 22 in 559 mm A C 14 4 in 366 mm C Wall Thickness Front 0 75 in 19 mm HB Side 0 75 in 19 mm gt Box Parts Box Shape Square Prism 1 Top 1 Bottom depth c 15 9 in 404 mm width b 28 5 in 597 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 17 in 432 mm c gt width d 22 in 559 mm thickness 0 75 in 19 mm 2 Sides height a 17 in 432 mm depth c 15 9 in 404 mm thickness 0 75 in 19 mm a Back Driver Mounting Mounting Front h Vent Parts Square 4 A 1 Duct O Do g outside diameter e 4 25 in 108 mm Y inside diameter g 4 in 102 mm length h 5 422 in 138 mm 2008 directed electronics all rights reserved 23 FRAN AIS
25. of the second woofer coil Three dual 4 ohm voice coil woofer with voice coils of each woofer wired in series and then parallel the three woofers for a resulting 2 67 ohm load to the amplifier 4 ohm Figure 7 Figura 7 Abbildung 7 1 Connect each woofer in series by connecting the negative of the first coil to the positive terminal of the second coil 2 Wire the positive terminal of each woofer s first coil to the positive terminal on the amplifier Wire the negative terminal of each woofer s second coil to the negative terminal on the amplifier 8 2008 directed electronics all rights reserved Series Parallel Three Speakers dual 2 ohm voice coils Note Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil Three dual 2 ohm voice coil woofer with voice coils of each woofer wired in series and then parallel the three woofers for a resulting 1 33 ohm load to the amplifier 2 ohm Figure 8 Figura 8 Abbildung 8 1 Connect each woofer in series by connecting the negative of the first coil to the positive terminal of the second coil 2 Wire the positive terminal of each woofer s first coil to the positive terminal on the amplifier Wire the negative terminal of each woofer s second co
26. que se debe utilizar depende de la potencia y del tipo de veh culo en que se va a instalar Las cajas grandes son mejores si se tiene poca potencia de 25 a 50 del procesamiento de potencia del altavoz el veh culo es grande o se desea mayor salida Las cajas peque as se deben utilizar si se tiene la potencia recomendada de 50 a 100 del procesamiento de potencia nominal del altavoz el veh culo es peque o alta amplificaci n o se desea reproducci n de sonido m s precisa Las cajas selladas peque as dan m s control lo cual se traduce en bajos m s r pidos y precisos Las cajas con ventilaci n tienen m s eficiencia y m s salida de bajos en comparaci n con las selladas La caja ventilada aprovecha la onda de sonido trasera el sonido que sale por la parte de atr s del cono para reforzar la salida del altavoz Una caja cor rectamente sintonizada produce amplificaci n en todo el ancho de banda del sistema de subwoofer y mayor control de cono que una caja sellada La caja sintonizada a baja frecuencia produce menos amplificaci n general pero m s extensi n bajos m s bajos La caja sintonizada a alta frecuencia produce m s amplificaci n pero limita la respuesta de bajos del sistema Una de las ventajas de la caja con ventilaci n es que se puede sintonizar a una frecuencia espec fica y esa frecuencia se conoce como Fb Otra de las especificaciones importantes de la caja es la frecuencia de traspaso F3 en la que la respue
27. recomendadas Caixa selada t pica p s c bicos Caixa ventilada p s c bicos Frequ ncia de sintonizac o de duto Hz Equivalente quadrado do duto polegadas Comprimento do duto polegadas As especifica es est o sujeitas a alterac o sem aviso pr vio DETALHES DA CAIXA 1 Os par metros especificados s o apenas para aplica es convencionais Para obter mais ajuda ligue para o grupo de suporte t cnico de udio 2 MDF de 1 9 cm 0 75 recomendado 3 Os volumes das caixas recomendadas s o volumes L QUIDOS O deslocamento do alto falante e do duto est o inclu dos no volume da caixa N o necess rio adicion los para calcular o volume BRUTO da caixa NOTAS xx Devido alta capacidade de pot ncia e longo deslocamento desses woofers os par metros Thiele Small foram calculados e medidos usando um sistema analisador Klippel O produto de efici ncia da largura de banda EBP determinado pela seguinte f rmula Fs Qes EBP Valores de EBP de 50 ou menos sugerem que uma caixa selada melhor valores de 50 a 90 significam que os subwoofers s o vers teis e valores de 90 ou mais significam que uma caixa ventilada recomendada Filtros subs nicos devem ser sempre usados e ajustados especificamente para designs de caixa ventilada 2008 directed electronics Todos os direitos reservados 71 EXPLICA O DAS ESPECIFICA ES DAS CAIXAS Ex
28. 68 39 244 17 Cms mechanical compliance mm N 0 170 0 146 0 112 BI motor strength Tesla M 16 85 21 23 17 05 Sd effective radiating area sq cm 283 529 283 529 463 770 Sd effective radiating area sq m 0 028 0 028 0 046 Sd effective radiating area sq in 43 964 43 964 71 912 Frequency range Hz 28 500 32 1 500 30 5 500 Energy Bandwidth Product EBP 58 59 49 Driver Physical Dimension Speaker Displacement cu ft 0 068 0 068 0 091 Mounting hole diameter inches mm 8 85 225 8 85 225 10 91 277 Mounting depth inches mm 5 86 149 5 86 149 6 45 164 Magnet Weight Oz 96 00 96 00 96 00 Basket diameter inches mm 10 23 260 10 23 260 12 28 312 Recommended Enclosures Typical sealed enclosure cu ft 0 75 0 75 1 50 Vented enclosure cu ft 0 75 0 75 1 50 Port tuning frequency Hz 44 00 44 00 40 00 Port diameter inside inches 3 00 3 00 4 00 Port square equivalent inches 2 659 x 2 659 2 659 x 2 659 3 545 x 3 545 Port length inches 11 19 11 19 11 26 Specifications are subject to change without notice 14 2008 directed electronics all rights reserved SPECIFICATIONS Model Part Number XTRPRO124 XTRPRO152 XTRPRO154 Thiele Small Parameters Fs free air resonance Hz 32 3 23 4 28 7 Vas equivalent compliance cu ft 1 256 3 464 3 207 Vas equivalent compliance liters 35 590 98 130 90 860 Qms Q mechanical 5
29. EORION HIGH PERFORMANCE CAR AUDIO Subwoofer OWNER S MANUAL MODEL XTRPRO 102 XTRPRO 104 XTRPRO 122 XTRPRO 124 XTRPRO152 XTRPRO154 TABLE OF CONTENTS EMO Slices ix caia lar daa iaa 1 FRANCAIS rr sb sac 25 ESPA O nuvo cerda rd e ae is 35 Deutsch civic dae a a a a le ne A en 45 Italiano iaia era i 55 POrtUGUES ii a id diene das ha deb pai 65 Introduction iii den Re eww nn 1 Practice Safe SOUNG iii Sawada se eee 1 What s inithe boX cerren dau ans gs ss n 2 TOONS OF the Trade sa tirare iena 2 Installation scia wu ii a OR a waa rev 2 Finding Speaker Mounting Locations 2 Features ciclo ia ate ERA Aaa 3 Wiring Configurations iea 22102 oserei 4 Specifications iui au reage ia se E E E A ERE DA 14 Enclosure Recommendations 18 Warranty pus nenn TIE O adage aches Back cover INTRODUCTION Thank you for your purchase of the Orion XTRPRO Subwoofers These woofers represent a combination of incredible performance and value We at Orion strive to give you the latest up to date information about this product What we can t give you with the manual is personal installation or technical experience If you have questions concerning the use or application of this product please refer to the nearest Orion dealer for assistance visit www orioncaraudio com or call the technical support hotline at 1 800 876 0800 As we are always finding new
30. ETOS El desplazamiento del altavoz y del puerto se incluyen en el volumen de la caja No es necesario agregarlos para calcular el volumen BRUTO de la caja NOTAS kk Debido a las capacidades de alta potencia y gran desplazamiento lineal de estos woofers los par metros Thiele Small se calculan y se miden con un sistema analizador Klippel El Producto Ancho de Banda Energ a Energy Bandwidth Product EBP se determina por medio de la siguiente f rmula Fs Qes EBP Los valores EBP de menos de 50 sugieren caja sellada de 50 a 90 subwoofer vers til m s de 90 caja con ventilaci n Se deben utilizar siempre filtros subs nicos ajustados espec ficamente al dise o de la caja ventilada 2008 directed electronics Reservados todos los derechos 41 EXPLICACION DE LAS ESPECIFICACIONES DE LAS CAJAS Hay muchos factores que contribuyen a determinar el mejor estilo de caja para usted o su veh culo A continuaci n se presentan algunos factores que se deben tener en cuenta El tama o de la caja es directamente proporcional a la eficiencia y el procesamiento de potencia del altavoz Un woofer en una caja peque a procesa m s potencia que el mismo woofer en una caja grande La eficiencia es exactamente lo contrario una caja grande reproduce frecuencias m s bajas a mayor volumen con menos potencia que una caja peque a El siguiente dise o de caja sellada da la mejor calidad de sonido en general El tama o de la caja
31. S FOR PARTICULAR PURPOSE AND WARRANTY OF NON INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS IN NO EVENT WILL DIRECTED BE LIABLE FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF PROFITS BY PURCHASING THIS PRODUCT THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY CALIFORNIA This warranty is only valid for sale of Product within the United States of America Product sold outside of the United States of America is sold AS IS and shall have NO WARRANTY express or implied Some states do not allow limitation on how long an implied warranty lasts In such states the limitation or exclusions of this Limited Warranty may not apply Some states do not allow the exclusion or limitation of incidental or consequential damages In such states the exclusion or limitation of this Limited Warranty may not apply to you This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state 920 0033 04 07 For more information on Orion products please visit www orioncaraudio com di
32. Tieft ner Schwingspule mit dem positiven Terminal der anderen Spule verbinden 2 Verbinden Sie das positive Terminal der ersten Tieft ner Schwingspule mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der zweiten Tieft ner Schwingspule mit dem negativen Terminal am Verst rker Parallel Ein Lautsprecher Doppelte 2 Ohm Schwingspulen Siehe Abbildung 3 auf Seite 4 Ein Tieft ner mit doppelten 2 Ohm Schwingspulen bei dem die Schwingspulen parallel geschaltet sind Lastwiderstand von 1 Ohm am Verst rker 1 SchlieBen Sie den Lautsprecher parallel an indem Sie jeweils die beiden positiven Terminals und die beiden negativen Terminals miteinander verbinden 2 Verbinden Sie die positiven Terminals des Tieft ners mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal des Tieft ners mit dem negativen Terminal am Verst rker Parallel Ein Lautsprecher Doppelte 4 Ohm Schwingspulen Siehe Abbildung 4 auf Seite 5 Ein Tieft ner mit doppelten 4 Ohm Schwingspulen bei dem die Schwingspulen parallel geschaltet sind Lastwiderstand von 2 Ohm am Verst rker 1 SchlieBen Sie den Lautsprecher parallel an indem Sie jeweils die beiden positiven Terminals und die beiden negativen Terminals miteinander verbinden 2 Verbinden Sie die beiden positiven Terminals des Tieft ners mit dem positiven Terminal am Verst rker Verbinden Sie
33. a prima bobina al terminale positivo della seconda 2 Collegare il terminale positivo della prima bobina di ciascun woofer al terminale positivo dell amplificatore e il terminale negativo della seconda bobina di ciascun woofer al terminale negativo dell amplificatore 58 2008 directed electronics tutti i diritti riservati Quattro diffusori in serie parallelo ciascuno con due bobine mobili da 4 ohm Vedi Figura 9 a pagina 10 Nota verificare che i woofer siano cablati come illustrato con il terminale negativo della prima bobina mobile di ciascun woofer collegato al terminale positivo della seconda bobina mobile del woofer stesso Quattro woofer con due bobine mobili da 4 ohm ciascuno collegate in serie applicano un carico di 2 ohm all amplificatore quando sono collegati in parallelo 1 Collegare ciascun woofer in serie collegandone il terminale negativo della prima bobina al terminale positivo della seconda 2 Collegare il terminale positivo della prima bobina di ciascun woofer al terminale positivo dell amplificatore e il terminale negativo della seconda bobina di ciascun woofer al terminale negativo dell amplificatore Quattro diffusori in serie parallelo ciascuno con due bobine mobili da 2 ohm Vedi Figura 10 a pagina 11 Nota verificare che i woofer siano cablati come illustrato con il terminale negativo della prima bobina mobile di ciascun woofer collegato al terminale positivo
34. ado com o terminal negativo da bobina do primeiro woofer conectado ao terminal positivo da bobina do segundo woofer Quatro woofers com duas bobinas m veis de 4 ohm devem ser conectados com as bobinas de cada woofer em s rie e em seguida os quatro woofers em paralelo resultando em uma carga de 2 ohm ao amplificador 1 Conecte cada woofer em s rie unindo o terminal negativo da primeira bobina ao terminal positivo da segunda bobina 2 Conecte os terminais positivos da primeira bobina de cada woofer ao terminal positivo do amplificador Conecte o terminal negativo da segunda bobina de cada woofer ao terminal negativo do amplificador S rie Paralela Quatro alto falantes duas bobinas de 2 ohm Ver figura 10 na p gina 11 Nota Verifique e certifique se de que os cabos dos woofers estejam conectados como mostrado com o terminal negativo da bobina do primeiro woofer conectado ao terminal positivo da bobina do segundo woofer Quatro woofers com duas bobinas m veis de 2 ohm devem ser conectados com as bobinas de cada woofer em s rie e em seguida os quatro woofers em paralelo resultando em uma carga de 1 ohm ao amplificador 1 Conecte cada woofer em s rie unindo o terminal negativo da primeira bobina ao terminal positivo da segunda bobina 2 Conecte os terminais positivos da primeira bobina de cada woofer ao terminal positivo do amplificador Conecte o terminal negativo da segunda bobina
35. ali negativi del woofer al terminale negativo dell amplificatore Due diffusori in parallelo ciascuno con due bobine mobili da 4 ohm Vedi Figura 5 a pagina 6 Due woofer con due bobine mobili da 4 ohm ciascuno collegate in parallelo applicano un carico di 1 ohm all amplificatore quando sono collegati in parallelo 1 Collegare i woofer in parallelo collegandone tra loro i quattro terminali positivi e i quattro terminali negativi 2 Collegare tutti i terminali positivi del woofer al terminale positivo dell amplificatore e tutti i terminali negativi del woofer al terminale negativo 2008 directed electronics tutti i diritti riservati 57 dell amplificatore Due diffusori in serie parallelo ciascuno con due bobine mobili da 2 ohm Vedi Figura 6 a pagina 7 Nota verificare che i woofer siano cablati come illustrato con il terminale negativo della prima bobina mobile di ciascun woofer collegato al terminale positivo della seconda bobina mobile del woofer stesso Due woofer con due bobine mobili da 2 ohm ciascuno collegate in serie applicano un carico di 2 ohm all amplificatore quando sono collegati in parallelo 1 Collegare ciascun woofer in serie collegandone il terminale negativo della prima bobina al terminale positivo della seconda 2 Collegare il terminale positivo della prima bobina di ciascun woofer al terminale positivo dell amplificatore e il terminale negativo della s
36. ancia nominal Q Le inductancia mH Eficiencia 1 W a 1 m dB Eficiencia 2 86 V a 1 m dB Xmax desplazamiento lineal de ida plg Xmax desplazamiento lineal de ida mm Pe procesamiento continuo de potencia W Procesamiento m ximo de potencia m sica W Mms masa total en movimiento g Cms cumplimiento mec nico mm N Bl fuerza del motor Tesla m Sd rea de radiaci n efectiva cm2 Sd rea de radiaci n efectiva m2 Sd rea de radiaci n efectiva plg 2 Gama de frecuencias Hz Producto ancho de banda energ a EBP Dimensiones f sicas del excitador Desplazamiento del altavoz pies3 40 2008 directed electronics Reservados todos los derechos Di metro del agujero de montaje plg mm Profundidad de montaje plg mm Peso del im n oz Di metro de la canasta plg mm Cajas recomendadas Caja sellada normal pies3 Caja ventilada pies3 Frecuencia de sintonizaci n del puerto Hz Equivalente cuadrado del puerto plg Longitud del puerto plg Especificaciones sujetas a cambio sin aviso previo DETALLES DE LA CAJA 1 Los par metros indicados son s lo para aplicaciones convencionales Si necesita m s asistencia llame a Apoyo T cnico de Sonido 2 Se recomienda MDF de 0 75 plg 19mm de grosor 3 Los vol menes de caja recomendados son N
37. ativa o si desidera una potenza maggiore Una cassa pi piccola preferibile se la potenza quella suggerita dal 50 al 100 di quella massima tollerabile dall altoparlante il veicolo abbastanza piccolo guadagno elevato o si desidera una riproduzione pi fedele del suono La cassa pi piccola sigillata offre un controllo superiore che assicura bassi pi veloci e precisi Una cassa ventilata offre efficienza maggiore e un uscita ai bassi estremi pi forte rispetto a una cassa sigillata La prima utilizza l onda regressiva il suono che si propaga dal lato posteriore del cono per amplificare l uscita dell altoparlante Una cassa sintonizzata correttamente assicura un guadagno costante nell intera larghezza di banda del subwoofer e offre un controllo del cono superiore rispetto a una cassa sigillata La sintonizzazione alle basse frequenze offre un guadagno complessivo inferiore ma un estensione superiore bassi estremi mentre una cassa sintonizzata alle frequenze alte offre un guadagno superiore ma limita la risposta dell impianto alle basse frequenze Uno dei vantaggi della cassa ventilata la possibilit di sintonizzarla a una frequenza specifica nota come Fb Un altro parametro importante della cassa F3 cio la frequenza alla quale la risposta del driver attenuata di 3 dB Questo valore importante perch determina l impostazione del filtro passa alto o dell ORION IntelliQ quest ultimo va impostato a una fre
38. bobina ao terminal negativo do amplificador Paralela Um alto falante duas bobinas de 2 ohm Ver figura 3 na p gina 4 Um woofer com duas bobinas m veis de 2 ohm conectadas em paralelo resulta em uma carga de 1 ohm ao amplificador 1 Conecte o alto falante em paralelo unindo os dois terminais positivos juntos e os dois terminais negativos juntos 2 Conecte os terminais positivos do woofer ao terminal positivo do amplificador Conecte os terminais negativos do woofer ao terminal negativo do amplificador Paralela Um alto falante duas bobinas de 4 ohm Ver figura 4 na p gina 5 Um woofer com duas bobinas m veis de 4 ohm conectadas em paralelo resulta em uma carga de 2 ohm ao amplificador 1 Conecte o alto falante em paralelo unindo os dois terminais positivos juntos e os dois terminais negativos juntos 2 Conecte os dois terminais positivos do woofer ao terminal positivo do amplificador Conecte os dois terminais negativos do woofer ao terminal negativo do amplificador Paralela Dois alto falantes duas bobinas de 4 ohm Ver figura 5 na p gina 6 Dois woofers com duas bobinas m veis de 4 ohm conectadas em paralelo e os dois woofers em paralelo resultam em uma carga de 1 ohm ao amplificador 1 Conecte o alto falante em paralelo unindo os quatro terminais positivos juntos e os quatro terminais negativos juntos 2 Conecte os terminais positivos dos
39. cs Tous droits r serv s 25 CARACT RISTIQUES 26 O OA 7 AL 14 0000000000 0000000000 5 12 gt O O 00000000001 0000000000 0000000000 1 z 6 J O Calotte pare poussi re en polypropyl ne r sistante l humidit et aux UV Suspension surdimensionn e en caoutchouc nitrile butadi ne permettant une longue course contr l e C ne papier r sistant l humidit et aux UV Ch ssis sur mesure en fonte d aluminium Corps de bobine mobile en aluminium avec vents corps de bobine mobile de 2 5 Plaque avant en acier 8 mm Pile de 2 gros aimants c ramique Plaque arri re en acier 8 mm bloc de pi ce polaire en T vent de 29 mm faisant partie du syst me de refroidissement am lior de la bobine mobile convection forc e Protecteur d aimant en PVC Bobine mobile en cuivre haute temp rature 2 ohms double ou 4 ohms double Events dans le corps de bobine mobile Font partie du syst me de refroidissement am lior de la bobine mobile convection forc e Anneau de centrage double Conex entrelac avec fils rosettes cousus et en boucles Borniers personnalis es Enjoliveur en ABS 2008 directed electronics Tous droits r serv s CONFIGURATIONS DE C BLAGE S rie Un haut parleur deux bobines mobiles de 2 ohms Voir la figure 2 la
40. d accord net 4 Les enceintes contiennent une quantit minimale de mat riaux d amortissement Il suffit de pr voir assez de tissu pour le rev tement int rieur de l enceinte Explication des diagrammes de caissons clos voir les dimensions en pages 18 20 et 22 Propri t s du caisson Description Type Caisson clos Forme Prisme carr gt Avant et arri re 2008 directed electronics Tous droits r serv s Param tres du caisson Vb V total Qtc QL F3 Remplissage Dimensions externes A B C Dimensions internes A B C paisseur parois Avant C t s El ments du caisson Forme du caisson prisme carr 1 haut 1 bas profondeur c largeur b paisseur 1 avant 1 arri re hauteur a largeur d paisseur 2 c t s hauteur a profondeur c paisseur Montage du haut parleur Montage Avant 33 Explication des diagrammes de caissons vent accord voir les dimensions en pages 19 21 et 23 Propri t s du caisson Description Type Caisson vent accord Vb Param tres du caissor vents Nb d vents Forme Prisme carr V total Forme vent rond Qtc Extr mit vent une affleurante QL Dv F3 Lv Remplissage gt Avant et arri re 34 Dimensions externes A B C Dimensions inte
41. della seconda bobina mobile del woofer stesso Quattro woofer con due bobine mobili da 2 ohm ciascuno collegate in serie applicano un carico di 1 ohm all amplificatore quando sono collegati in parallelo 1 Collegare ciascun woofer in serie collegandone il terminale negativo della prima bobina al terminale positivo della seconda 2 Collegare il terminale positivo della prima bobina di ciascun woofer al terminale positivo dell amplificatore e il terminale negativo della seconda bobina di ciascun woofer al terminale negativo dell amplificatore Due amplificatori e un diffusore con due bobine mobili da 2 ohm Vedi Figura 11 a pagina 12 Un woofer con due bobine mobili da 2 ohm ciascuna collegata a un amplificatore separato applica un carico di 2 ohm a ciascun amplificatore 1 Collegare una delle bobine mobili del woofer al primo amplificatore collegandone il terminale positivo e quello negativo rispettivamente al terminale positivo e a quello negativo dell amplificatore stesso 2 Collegare l altra bobina mobile del woofer al secondo amplificatore collegandone il terminale positivo e quello negativo rispettivamente al terminale positivo e a quello negativo dell amplificatore stesso Due amplificatori e un diffusore con due bobine mobili da 4 ohm Vedi Figura 12 a pagina 13 Un woofer con due bobine mobili da 4 ohm ciascuna collegata a un amplificatore 2008 directed electronics
42. die beiden negativen Terminals des Tieft ners mit dem negativen Terminal am Verst rker Parallel Zwei Lautsprecher doppelte 4 Ohm Schwingspulen Siehe Abbildung 5 auf Seite 6 Zwei Tieft ner mit doppelten 4 Ohm Schwingspulen wobei die Schwingspulen und die beiden Tieft ner parallel geschaltet sind Lastwiderstand von 1 Ohm am Verst rker 1 SchlieBen Sie den Lautsprecher parallel an indem Sie jeweils die vier positiven Terminals und die vier negativen Terminals miteinander verbinden 2008 directed electronics Alle Rechte vorbehalten 47 2 Verbinden Sie die positiven Terminals der Tieft ner mit dem positiven Terminal am Verst rker Verbinden Sie die negativen Terminals der Tieft ner mit dem negativen Terminal am Verst rker Reihe Parallel Zwei Lautsprecher doppelte 2 Ohm Schwingspulen Siehe Abbildung 6 auf Seite 7 Hinweis Stellen Sie sicher dass die Tieft neranschl sse wie gezeigtvorgenommen wurden wobei der negative Anschluss an der ersten Tieft ner Schwingspule mit dem positiven Anschluss an der zweiten Tieft ner Schwingspule verbunden ist Zwei Tieft ner mit doppelten 2 Ohm Schwingspulen wobei die Schwingspulen in Reihe und dann die beiden Tieft ner parallel geschaltet sind Lastwiderstand von 2 Ohm am Verst rker 1 SchlieBen Sie jeden Tieft ner in Reihe an indem Sie das negative Terminal der ersten Schwingspule mit dem positiven Terminal der zweiten Spule
43. e der Faktoren die Sie in Betracht ziehen sollten Die Geh usegr e ist direkt proportional zum Leistungsverm gen und zur Belastbarkeit des Lautsprechers Ein Tieft ner in einem kleineren Geh use ist h her belastbar als derselbe Tieft ner in einem gr eren Geh use Das Gegenteil gilt f r das Leistungsverm gen ein gr eres Geh use gibt tiefe Frequenzen lauter wieder und mit weniger Stromverbrauch als ein kleineres Das folgende geschlossene Geh usedesign bietet generell die beste Soundqualit t Die zu verwendende Geh usegr e h ngt von der Leistung und Gr e des Fahrzeugs ab in das es eingebaut wird Gr ere Geh use sind am besten geeignet wenn Sie weniger Leistung zur Verf gung haben 25 bis 50 der Belastbarkeit des Lautsprechers ein gr eres Fahrzeug haben oder mehr Leistung wollen Sie sollten ein kleineres Geh use verwenden wenn Sie die empfohlene Leistung 50 bis 100 der Nennbelastbarkeit des Lautsprechers besitzen ein kleineres Fahrzeug mit h herem Verst rkungsfaktor haben oder eine pr zisere Soundwiedergabe w nschen Das kleinere geschlossene Geh use bietet mehr Kontrolle was einen h rbar schnelleren und pr ziseren Bass erm glicht Ein Bassreflexgeh use bietet mehr Leistungsverm gen und einen st rkeren Tiefbass im Vergleich zu einem geschlossenen Geh use Ein Bassreflexgeh use verwendet die hintere Welle Sound von der R ckseite der Membran um die Lautsprecherleistung zu erh
44. e graves en s rie en raccordant la borne n gative de la premi re bobine la borne positive de la seconde 2 Raccordez la borne positive de la premi re bobine de chaque haut parleur de graves la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine de chaque haut parleur de graves la borne n gative de l amplificateur S rie parall le Trois haut parleurs deux bobines mobiles de 4 ohms Voir la figure 7 la page 8 Remarque V rifiez que le c blage du haut parleur de graves est conforme l illustration avec la borne n gative de la premi re bobine du haut parleur de graves reli e la borne positive de la seconde bobine Trois haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 4 ohms raccord es en s rie constituent une charge de 2 67 ohms pour l amplificateur 1 Configurez chaque haut parleur de graves en s rie en raccordant la borne n gative de la premi re bobine la borne positive de la seconde 2 Raccordez la borne positive de la premi re bobine de chaque haut parleur de graves la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine de chaque haut parleur de graves la borne n gative de l amplificateur S rie parall le Trois haut parleurs deux bobines mobiles de 2 ohms Voir la figure 8 la page 9 Remarque V rifiez que le c blage du haut par
45. econda bobina di ciascun woofer al terminale negativo dell amplificatore Tre diffusori in serie parallelo ciascuno con due bobine mobili da 4 ohm Vedi Figura 7 a pagina 8 Nota verificare che i woofer siano cablati come illustrato con il terminale negativo della prima bobina mobile di ciascun woofer collegato al terminale positivo della seconda bobina mobile del woofer stesso Tre woofer con due bobine mobili da 4 ohm ciascuno collegate in serie applicano un carico di 2 67 ohm all amplificatore quando sono collegati in parallelo 1 Collegare ciascun woofer in serie collegandone il terminale negativo della prima bobina al terminale positivo della seconda 2 Collegare il terminale positivo della prima bobina di ciascun woofer al terminale positivo dell amplificatore e il terminale negativo della seconda bobina di ciascun woofer al terminale negativo dell amplificatore Tre diffusori in serie parallelo ciascuno con due bobine mobili da 2 ohm Vedi Figura 8 a pagina 9 Nota verificare che i woofer siano cablati come illustrato con il terminale negativo della prima bobina mobile di ciascun woofer collegato al terminale positivo della seconda bobina mobile del woofer stesso Tre woofer con due bobine mobili da 2 ohm ciascuno collegate in serie applicano un carico di 1 33 ohm all amplificatore quando sono collegati in parallelo 1 Collegare ciascun woofer in serie collegandone il terminale negativo dell
46. ecte cada woofer en serie conectando la terminal negativa de una bobina a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina de cada woofer a la terminal positiva del amplificador Conecte la terminal negativa de la segunda bobina de cada woofer a la terminal negativa del amplificador En serie paralelo cuatro altavoces dos bobinas ac sticas de 2 Q cada uno Vea la figura 10 en la p gina 11 Nota Verifique y aseg rese de que el cableado del woofer es como se muestra la terminal negativa de la bobina de un woofer conectada a la terminal positiva de la bobina del otro woofer Cuatro woofers con dos bobinas ac sticas de 2 Q cada uno las bobinas ac sticas en serie y los 4 woofers en paralelo producen una carga de 1 Q en el amplificador 1 Conecte cada woofer en serie conectando la terminal negativa de una bobina a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina de cada woofer a la terminal positiva del amplificador Conecte la terminal negativa de la segunda bobina de cada woofer a la terminal negativa del amplificador 2 amplificadores un altavoz dos bobinas ac sticas de 2 2 Vea la figura 11 en la p gina 12 Un woofer con 2 bobinas ac sticas de 2 Q y cada bobina ac stica conectada a su propio amplificador produce una carga de 2 2 en cada amplificador 1 Conecte la terminal positiva y
47. eicolo 2008 directed electronics tutti i diritti riservati 55 CARATTERISTICHE O OA 7 AL 14 0000000000 0000000000 5 12 gt O O 00000000001 0000000000 0000000000 11 z 6 Protezione parapolvere in polipropilene resistente all umidit e ai raggi ultravioletti Surround maggiorato in NBR gomma nitrile butadiene per lunga escursione lineare controllata Cono in carta resistente all umidit e ai raggi ultravioletti Telaio in alluminio pressofuso su misura Supporto della bobina mobile in alluminio ventilata supporto da 6 4 cm Piastra anteriore in acciaio da 8 mm Due grandi magneti ceramici in cascata Piastra posteriore in acciaio da 8 mm staffa a T per i poli Apertura da 19 mm Parte del sistema migliorato di raffreddamento della bobina mobile a convezione forzata Protezione del magnete in PVC Bobina mobile da 4 ohm o 2 ohm doppia in rame per alte temperature Aperture di ventilazione del supporto della bobina mobile Parte del sistema migliorato di raffreddamento della bobina mobile a convezione forzata Doppio centratore in Conex intrecciato con fili conduttori applicati e avvolti Morsettiere su misura Anello di finitura in plastica ABS 56 2008 directed electronics tutti i diritti riservati CONFIGURAZIONI DI CABLAGGIO Un di
48. ffusore in serie con due bobine mobili da 2 ohm Vedi Figura 2 a pagina 4 Un woofer con due bobine mobili da 2 ohm collegate in serie applica un carico di 4 ohm all amplificatore 1 Collegare il woofer in serie collegando il terminale negativo di una bobina al terminale positivo dell altra bobina 2 Collegare il terminale positivo della prima bobina al terminale positivo dell amplificatore e il terminale negativo della seconda bobina al terminale negativo dell amplificatore Un diffusore in parallelo con due bobine mobili da 2 ohm Vedi Figura 3 a pagina 4 Un woofer con due bobine mobili da 2 ohm collegate in parallelo applica un carico di 1 ohm all amplificatore 1 Collegare il woofer in parallelo collegandone tra loro i due terminali positivi e i due terminali negativi 2 Collegare entrambi i terminali positivi del woofer al terminale positivo dell amplificatore ed entrambi i terminali negativi del woofer al terminale negativo dell amplificatore Un diffusore in parallelo con due bobine mobili da 4 ohm Vedi Figura 4 a pagina 5 Un woofer con due bobine mobili da 4 ohm collegate in parallelo applica un carico di 2 ohm all amplificatore 1 Collegare il woofer in parallelo collegandone tra loro i due terminali positivi e i due terminali negativi 2 Collegare entrambi i terminali positivi del woofer al terminale positivo dell amplificatore ed entrambi i termin
49. gt O O 00000000001 0000000000 0000000000 Cone de papel resistente umidade e radia o ultravioleta Estrutura de aluminio fundido personalizada Copo de bobina m vel de aluminio ventilado copo de bobina m vel de 2 5 Placa frontal de ago de 8 mm mas cer micos grandes de duas camadas Conjunto de placa traseira haste em T tipo forquilha de 8 mm de aco Abertura de ventilac o de 28 6 mm Parte do sistema aperfeicoado de arrefecimento da bobina convecc o forcada Protetor dos m s de PVC Bobina m vel dupla de cobre de alta temperatura de 2 ohm ou 4 ohm Ventila o no copo da bobina Parte do sistema aperfei oado de arrefecimento da bobina convecc o forcada Duas aranhas Conex entrelacadas com terminais de ouropel costurados em loop Blocos de terminais personalizados Anel de acabamento de ABS 2008 directed electronics Todos os direitos reservados CONFIGURA ES DE CONEX O Em s rie Um alto falante duas bobinas de 2 ohm Ver figura 2 na p gina 4 Um woofer com duas bobinas m veis de 2 ohm conectadas em s rie resulta em uma carga de 4 ohm ao amplificador 1 Conecte o woofer em s rie unindo o p lo negativo de um terminal ao p lo positivo do terminal da outra bobina 2 Conecte o terminal positivo da primeira bobina ao terminal positivo do amplificador Conecte o terminal negativo da segunda
50. gura 10 Abbildung 10 1 Connect each woofer in series by connecting the negative of the first coil to the positive terminal of the second coil 2 Wire the positive terminals of the first coil of each woofer to the positive terminal on the amplifier Wire the negative terminal of the second coil of each woofer to the negative terminal on the amplifier 2008 directed electronics all rights reserved 11 2 Amplifiers One Speaker dual 2 ohm voice coils One dual 2 ohm voice coil woofer with each voice coil connected to an individual amplifier resulting in a 2 ohm load to each amplifier Figure 11 Figura 11 Abbildung 11 1 Connect one of the speaker s voice coils to the first amplifier by connecting the positive terminal and the negative terminal from the speaker to the respective positive terminal and the negative terminal from the first amplifier 2 Connect the other of the speaker s voice coils to the second amplifier by connecting the positive terminal and negative terminal from the speaker to the respective positive terminal and the negative terminal from second amplifier 12 2008 directed electronics all rights reserved 2 Amplifiers One Speaker dual 4 ohm voice coils One dual 4 ohm voice coil woofer with each voice coil connected to an individual amplifier resulting in a 4 ohm load to each amplifier Figure 12 Fig
51. hen Ein richtig eingestelltes Geh use bietet eine Leistungsst rke ber die gesamte Bandbreite des Subwoofersystems hinweg und mehr Membrankontrolle als ein geschlossenes Geh use Eine niedrige Einstellung bietet weniger Gesamtverst rkung aber eine st rkere Auslenkung Tiefbass Ein hoch eingestelltes Geh use bietet mehr Verst rkung begrenzt aber den Tieffrequenzbereich des Systems Einer der Vorteile eines Bassreflexgeh uses ist die Einstellung auf eine bestimmte Tuningfrequenz als Fb bezeichnet Eine weitere wichtige Geh usespezifikation ist F3 die Absenkungsfrequenz bei der der Frequenzgang des Treibers um 3dB sinkt Dieser Wert ist bei der Einstellung des Hochpassfilters oder Ihres ORION IntelliQ wichtig Das IntelliQ sollte auf die Frequenz F3 eingestellt werden da dies eine Besch digung des Lautsprechers durch berlastung verhindert Eine gute Planung und fachgem e Konstruktion garantieren eine optimale Leistung Ihres Systems Die n chsten Seiten beschreiben verschiedene Geh use und Designs die die Leistung Ihrer XTRPRO Subwoofer verbessern 52 2008 directed electronics Alle Rechte vorbehalten GEHAUSEEMPFEHLUNGEN Geh usedetails 1 F r Baumaterial mit 34 Zoll 1 9 cm Dicke berechnete AuBenmaBe 2 EinschlieBlich Lautsprecherhub 3 Angegebene Volumen sind Netto Tuningvolumen 4 Geh use besitzen ein Minimum an D mpfungsmaterial Es ist gerade genug Material zur Auskleidung der Innensei
52. il to the negative terminal on the amplifier 2008 directed electronics all rights reserved 9 Series Parallel Four Speakers dual 4 ohm voice coils Note Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil Four dual 4 ohm voice coil woofers should be wired with the voice coils on each woofer in series and then parallel the four woofers for a resulting 2 ohm load to the amplifier Figure 9 Figura 9 Abbildung 9 1 Connect each woofer in series by connecting the negative of the first coil to the positive terminal of the second coil 2 Wire the positive terminals of the first coil of each woofer to the positive terminal on the amplifier Wire the negative terminal of the second coil of each woofer to the negative terminal on the amplifier 10 2008 directed electronics all rights reserved Series Parallel Four Speakers dual 2 ohm voice coils Note Verify and ensure that the woofer wiring is connected as shown with the negative connection from the first woofer coil connected to the positive connection of the second woofer coil Four dual 2 ohm voice coil woofers should be wired with the voice coils on each woofer in series and then parallel the four woofers for a resulting 1 ohm load to the amplifier Figure 10 Fi
53. istem muitos fatores diferentes que ajudam a determinar o melhor estilo de caixa para o usu rio ou o ve culo Estes s o alguns fatores que devem ser considerados O tamanho da caixa diretamente proporcional efici ncia e pot ncia m xima permiss vel do alto falante Um woofer em uma caixa pequena processa mais pot ncia do que o mesmo woofer em uma caixa maior O oposto se aplica em termos de efici ncia Uma caixa maior reproduz frequ ncias mais baixas com volume mais alto com menos pot ncia que uma caixa menor O design de caixa selada a seguir melhor em termos de qualidade sonora em geral O tamanho da caixa a usar depende da pot ncia e do tipo de ve culo no qual ser colocada Caixas maiores s o mais adequadas se a pot ncia for limitada 25 a 50 da capacidade de processamento de pot ncia do alto falante se o ve culo for grande ou o usu rio desejar reprodu o sonora mais alta Uma caixa menor deve ser utilizada se a pot ncia recomendada estiver dispon vel 50 a 100 da capacidade nominal de processamento de pot ncia do alto falante se o ve culo for menor alto ganho ou o usu rio desejar uma reprodu o sonora mais precisa A caixa selada menor proporciona mais controle o que resulta em graves mais r pidos e precisos Uma caixa ventilada oferece maior efici ncia e reprodu o mais profunda de graves em rela o a uma caixa selada Uma caixa ventilada usa a onda posterior som da parte traseira do cone
54. itivo e negativo do segundo amplificador ESPECIFICACOES Tradu o das especifica es ver detalhes nas p ginas 14 e 15 Modelo N mero do produto XTRPRO Tamanho Par metros Thiele Small Fs resson ncia ao ar livre Hz Vas conformidade equivalente p s c bicos Vas conformidade equivalente litros Qms Q mecanica Qes Q el trica Qts Q total do alto falante Re resist ncia CC ohms Z imped ncia nominal ohms Le indut ncia mh Efici ncia 1 W a 1 M dB Efici ncia 2 86 V a 1 M dB Xmax excurs o linear unidirecional pol Xmax excurs o linear unidirecional mm Pe pot ncia m xima permiss vel cont nua watts Capacidade de processamento de pico de pot ncia m sica watts Mms massa total m vel gramas Cms conformidade mec nica mm N B1 for a do motor Tesla M Sd rea de radia o efetiva cm2 Sd rea de radia o efetiva m2 Sd rea de radia o efetiva in2 Faixa de frequ ncia Hz 70 2008 directed electronics Todos os direitos reservados Produto de efici ncia da largura de banda EBP Dimensao fisica do alto falante Deslocamento do alto falante p s c bicos Di metro do orificio de montagem do alto falante pol mm Profundidade de instala o pol mm Peso do ima Oz Di metro do cone pol mm Caixas
55. l rights reserved 17 ENCLOSURE RECOMMENDATIONS Enclosure Details 1 External dimensions calculated for 3 4 building material 2 Includes speaker displacement 3 Volumes given are net tuning volume 4 Enclosures include a minimal amount of damping material Just enough material to line the inside of the enclosure is required XTRPRO102 amp 104 Sealed Enclosure Recommendations Box Properties Description Type Closed Box Shape Prism Square gt Bottom Front amp a Back Figure 14 Figura 14 Abbildung 14 18 Box Parameters Vb 0 75 cu ft V total 0 791 cu ft Qtc 0 598 QL u 7 F3 50 61 Hz Fill none External Dimensions A 12 in 305 mm B 15 5 in 394 mm C 10 8 in 274 mm Internal Dimensions A 10 5 in 267 mm B 14 in 356 mm C 9 3 in 236 mm Wall Thickness Front 0 75 in 19 mm Side 0 75 in 19 mm Box Parts Box Shape Square Prism 1 Top 1 Bottom depth c 10 8 in 274 mm width b 15 5 in 394 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 10 5 in 267 mm width d 14 in 356 mm thickness 0 75 in 19 mm 2 Sides height a 10 5 in 267 mm depth c 10 8 in 274 mm thickness 0 75 in 19 mm Driver Mounting Mounting Front 2008 directed electronics all rights reserved XTRPRO102 amp 104 Vented Enclosure Recommendations Box Properties Descriptio
56. la terminal negativa de una de las bobinas del altavoz a la terminal positiva y la terminal negativa correspondientes de uno de los amplificadores 2 Conecte la terminal positiva y la terminal negativa de la otra bobina del altavoz a la terminal positiva y la terminal negativa correspondientes del otro amplificador 2 amplificadores un altavoz dos bobinas ac sticas de 4 2 Vea la figura 12 en la p gina 13 2008 directed electronics Reservados todos los derechos 39 Un woofer con 2 bobinas ac sticas de 4 Q y cada bobina ac stica conectada a su propio amplificador produce una carga de 4 Q en cada amplificador 1 Conecte la terminal positiva y la terminal negativa de una de las bobinas del altavoz a la terminal positiva y la terminal negativa correspondientes de uno de los amplificadores 2 Conecte la terminal positiva y la terminal negativa de la otra bobina del altavoz a la terminal positiva y la terminal negativa correspondientes del otro amplificador ESPECIFICACIONES Traducci n de las especificaciones vea las p ginas 14 y 15 para m s detalles Modelo N de pieza XTRPRO Tama o Par metros Thiele Small Fs resonancia al aire libre Hz Vas cumplimiento de equivalencia pies3 Vas cumplimiento de equivalencia litros Qms Q mec nico Qes Q el ctrico Qts Q total del excitador Re resistencia CC 2 Z imped
57. leur de graves est conforme l illustration avec la borne n gative de la premi re bobine du haut parleur de graves reli e la borne positive de la seconde bobine Trois haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 2 ohms raccord es en s rie constituent une charge de 1 33 ohms pour l amplificateur 28 2008 directed electronics Tous droits r serv s 1 Configurez chaque haut parleur de graves en s rie en raccordant la borne n gative de la premi re bobine la borne positive de la seconde 2 Raccordez la borne positive de la premi re bobine de chaque haut parleur de graves la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine de chaque haut parleur de graves la borne n gative de l amplificateur S rie parall le Quatre haut parleurs deux bobines mobiles de 4 ohms Voir la figure 9 la page 10 Remarque V rifiez que le c blage du haut parleur de graves est conforme l illustration avec la borne n gative de la premi re bobine du haut parleur de graves reli e la borne positive de la seconde bobine Quatre haut parleurs de graves en parall le avec pour chacun les deux bobines mobiles de 4 ohms raccord es en s rie constituent une charge de 2 ohms pour l amplificateur 1 Configurez chaque haut parleur de graves en s rie en raccordant la borne n gative de la premi re bobine la borne positive
58. lificateur 1 Raccordez l une des bobines mobiles du haut parleur au premier amplificateur en reliant les bornes positive et n gative du haut parleur aux bornes positive 2008 directed electronics Tous droits r serv s 29 et n gative correspondantes du premier amplificateur 2 Raccordez l autre bobine mobile du haut parleur au second amplificateur en reliant les bornes positive et n gative du haut parleur aux bornes positive et n gative correspondantes du second amplificateur 2 amplificateurs Un haut parleur deux bobines mobiles de 4 ohms Voir la figure 12 la page 13 Un haut parleur de graves deux bobines mobiles de 4 ohms raccord es chacune un amplificateur distinct constitue une charge de 4 ohms pour chaque amplificateur 1 Raccordez l une des bobines mobiles du haut parleur au premier amplificateur en reliant les bornes positive et n gative du haut parleur aux bornes positive et n gative correspondantes du premier amplificateur 2 Raccordez l autre bobine mobile du haut parleur au second amplificateur en reliant les bornes positive et n gative du haut parleur aux bornes positive et n gative correspondantes du second amplificateur SP CIFICATIONS Explication des caract ristiques techniques voir les d tails en pages 14 et 15 Mod le R f rence XTRPRO Taille Param tres Thiele Small Fs r sonance l air libre
59. minal negativa de la segunda bobina de cada woofer a la terminal negativa del amplificador En serie paralelo tres altavoces dos bobinas ac sticas de 2 Q cada uno Vea la figura 8 en la p gina 9 Nota Verifique y aseg rese de que el cableado del woofer es como se muestra la terminal negativa de la bobina de un woofer conectada a la terminal positiva de la bobina del otro woofer Tres woofers con dos bobinas ac sticas de 2 2 cada uno las bobinas ac sticas en serie y los 3 woofers en paralelo producen una carga de 1 33 Q en el amplificador 1 Conecte cada woofer en serie conectando la terminal negativa de una bobina a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina de cada woofer a la terminal positiva del amplificador Conecte la terminal negativa de la segunda bobina de cada woofer a la terminal negativa del amplificador 38 2008 directed electronics Reservados todos los derechos En serie paralelo cuatro altavoces dos bobinas ac sticas de 4 O cada uno Vea la figura 9 en la p gina 10 Nota Verifique y aseg rese de que el cableado del woofer es como se muestra la terminal negativa de la bobina de un woofer conectada a la terminal positiva de la bobina del otro woofer Cuatro woofers con dos bobinas ac sticas de 4 Q cada uno las bobinas ac sticas en serie y los 4 woofers en paralelo producen una carga de 2 Q en el amplificador 1 Con
60. n Type Vented Box Shape Prism Square Figure 15 Figura 15 Abbildung 15 lt h O Ci O 2008 directed electronics all rights reserved Box Parameters Vb V total Fb QL F3 Fill Vents 0 75 cu ft No of Vents 1 0 841 cu ft Vent shape round 44 Hz Vent ends one flush 7 Dv 3 in 76 mm 35 24 Hz Lv 11 19 in 284 mm none External Dimensions A 12 in 305 mm B 15 5 in 394 mm C 11 39 in 289 mm Internal Dimensions A 10 5 in 267 mm B 14 in 356 mm C 9 89 in 251 mm Wall Thickness Front 0 75 in 19 mm Side 0 75 in 19 mm Box Parts Box Shape Square Prism 1 Top 1 Bottom depth c 11 39 in 289 mm width b 15 5 in 394 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 10 5 in 267 mm width d 14 in 856 mm thickness 0 75 in 19 mm 2 Sides height a 10 5 in 267 mm depth c 11 39 in 289 mm thickness 0 75 in 19 mm Driver Mounting Mounting Front Vent Parts 1 Duct outside diameter e 3 25 in 83 mm inside diameter g 3 in 76 mm length h 11 19 in 284 mm XTRPRO122 amp 124 Sealed Enclosure Recommendations Box Properties Description Box Parameters Type Closed Box Vb 1 5 cu ft Shape Prism Square V total 1 55 cu ft Qte 0 717 QL 6 886 F3 43 09 Hz Fill none External Dimensions A 16 in 406 mm B 16 in
61. n la seguente formula Fs Qes EBP Valori di EBP minori o uguali a 50 suggeriscono che preferibile adoperare una cassa sigillata valori compresi tra 50 e 90 indicano che i subwoofer sono versatili e valori uguali o maggiori di 90 suggeriscono che preferibile adoperare una cassa ventilata necessario usare sempre filtri subsonici regolandoli specificamente per la costruzione a cassa ventilata 2008 directed electronics tutti i diritti riservati 61 SPIEGAZIONE DEI DATI TECNICI DELLA CASSA Il tipo migliore di cassa per le esigenze del proprietario o le condizioni del veicolo dipende da numerosi fattori alcuni dei quali sono elencati di seguito Le dimensioni della cassa sono direttamente proporzionali all efficienza e alla potenza tollerabile dall altoparlante quest ultima tanto maggiore quanto pi piccola la cassa in cui inserito il woofer mentre per l efficienza vale il criterio opposto ossia una cassa pi grande riproduce le frequenze pi basse a un volume pi alto e con meno potenza rispetto a una cassa pi piccola La costruzione della cassa sigillata illustrata di seguito quella ottimale ai fini della qualit complessiva del suono Le dimensioni della cassa da usare dipendono dalla potenza e dal tipo di veicolo in cui la si installer Le casse pi grandi sono ottimali se la potenza inferiore dal 25 al 50 di quella massima tollerabile dall altoparlante il veicolo ha una grandezza signific
62. nal of the second coil to the negative terminal on the amplifier Parallel One Speaker dual 2 ohm voice coils One dual 2 ohm voice coil woofer with voice coils in parallel results in a 1 ohm load to the amplifier Figure 3 Figura 3 Abbildung 3 1 Connect the speaker in parallel by connecting the two positive terminals together and the two negative terminals together 2 Wire the positive terminals of the woofer to the positive terminal on the amplifier Wire the negative terminals of the woofer to the negative terminal on the amp 4 2008 directed electronics all rights reserved Parallel One Speaker dual 4 ohm voice coils One dual 4 ohm voice coil woofer with voice coils in parallel results in a 2 ohm load to the amplifier Figure 4 Figura 4 Abbildung 4 1 Connect the speaker in parallel by connecting the two positive terminals together and the two negative terminals together 2 Wire both positive terminals of the woofer to the positive terminal on the amplifier Wire both negative terminals of the woofer to the negative terminal on the amplifier 2008 directed electronics all rights reserved 5 Parallel Two Speaker dual 4 ohm voice coils Two dual 4 ohm voice coil woofers with voice coils in parallel and the two woofers in parallel results in a 1 ohm load to the amplifier Figure 5 Figura 5 Abbildung 5 1
63. ntrol this audible translates into faster and more accurate bass A vented enclosure will offer greater efficiency and stronger low bass output compared to a sealed design A vented enclosure uses the back wave sound from the back side of the cone to reinforce the output from the speaker A properly tuned enclosure will yield gain across the entire bandwidth of the subwoofer system and offer more cone control than a sealed enclosure A low tuning will yield less overall gain but greater extension low bass A high tuned enclosure will offer more gain but limit the low end response of the system One of the advantages of having a vented enclosure is because it is tunable to a specific frequency and that tuning frequency is known as the Fb Another important box specification is F3 which is the roll off frequency at which the driver s response is down 3dB This is an important number when it comes to setting your high pass filter or your ORION Intelli Q The Intelli Q should be set at the same frequency as the F3 as this will keep the speaker from damaging or what is know as over loading Good planning and proper construction will assure the best response from your system The next pages will outline many different enclosures and designs that allow the XTRPRO subwoofers to perform best As always if you have any questions on enclosure construction or design call Technical Support 1 800 753 0800 2008 directed electronics al
64. orbehalten 49 2 Verst rker Ein Lautsprecher Doppelte 2 Ohm Schwingspulen Siehe Abbildung 11 auf Seite 12 Ein Tieft ner mit doppelten 2 Ohm Schwingspulen bei dem jede Schwingspule an einen separaten Verst rker angeschlossen ist Lastwiderstand von 2 Ohm am Verst rker 1 SchlieBen Sie eine der Schwingspulen des Lautsprechers an den ersten Verst rker an indem Sie das positive und negative Terminal am Lautsprecher mit dem entsprechenden positiven und negativen Terminal am ersten Verst rker verbinden SchlieBen Sie die andere Schwingspule des Lautsprechers an den zweiten Verst rker an indem Sie das positive und negative Terminal am Lautsprecher mit dem entsprechenden positiven und negativen Terminal am zweiten Verst rker verbinden 2 Verst rker Ein Lautsprecher Doppelte 4 Ohm Schwingspulen Siehe Abbildung 12 auf Seite 13 Ein Tieft ner mit doppelten 4 Ohm Schwingspulen bei dem jede Schwingspule an einen separaten Verst rker angeschlossen ist Lastwiderstand von 4 Ohm am Verst rker 1 SchlieBen Sie eine der Schwingspulen des Lautsprechers an den ersten Verst rker an indem Sie das positive und negative Terminal am Lautsprecher mit dem entsprechenden positiven und negativen Terminal am ersten Verst rker verbinden SchlieBen Sie die andere Schwingspule des Lautsprechers an den zweiten Verst rker an indem Sie das positive und negative Terminal am Lau
65. orn ffnungsteile 1 Kanal Au endurchmesser e Innendurchmesser g L nge h 2008 directed electronics Alle Rechte vorbehalten ITALIANO INSTALLAZIONE I risultati conseguibili con questi subwoofer XTRPRO dipendono direttamente dalla qualit dell installazione eseguendola con cautela si avr la certezza di ottenere un suono soddisfacente per anni e anni Se non si certi di poter eseguire l installazione correttamente rivolgersi al rivenditore Orion che sar in grado di fornire l assistenza tecnica necessaria Se si decide di installare personalmente questi altoparlanti prima di iniziare leggere l intera sezione relativa alle casse sigillate e ventilate INDIVIDUAZIONE DEI PUNTI DI MONTAGGIO DEGLI ALTOPARLANTI La scelta dei punti di montaggio degli altoparlanti ha la massima influenza sulla qualita del suono dell impianto Nello scegliere la collocazione che soddisfa meglio le proprie esigenze occorre considerare diversi fattori i punti prescelti devono offrire uno spazio sufficiente per gli altoparlanti e al tempo stesso occorre accertarsi di non causare interferenze con il funzionamento dei componenti meccanici o elettrici del veicolo La scelta della posizione migliore per gli altoparlanti dipende dalle esigenze estetiche del proprietario e dalla configurazione dell interno del veicolo In genere i woofer vengono installati nel bagagliaio presso il sedile posteriore o nella parte posteriore del v
66. os todos los derechos DEUTSCH INSTALLATION Die Leistung dieser XTRPRO Subwoofer h ngt direkt von der Qualit t der Installation ab Ein sorgf ltiges Vorgehen bei der Installation garantiert Ihnen jahrelange H chstleistungen Wenn Sie sich nicht sicher sind ob Sie die Installation selbst ausf hren k nnen wenden Sie sich bitte an Ihren rtlichen Orion Fachh ndler Orion H ndler haben ausgebildetes Fachpersonal das aus Ihrem Orion System das Maximum an Leistung herausholen kann Wenn Sie dieses Lautsprechersystem selbst installieren wollen sollten Sie vor Beginn der Installation den gesamten Abschnitt ber geschlossene Geh use und Bassreflexgeh use durchlesen SO PLATZIEREN SIE DIE LAUTSPRECHER Die Wahl der korrekten Lautsprecherposition hat groBe Auswirkungen auf die Soundqualit t des Systems Bei der Wahl der Lautsprecherposition die Ihren Ans pr chen am besten entspricht sind mehrere Faktoren zu beachten Es muss an der Stelle gen gend Platz f r den Lautsprecher vorhanden sein Sie m ssen sicherstel len dass die gew hlte Stelle die mechanischen oder elektrischen Funktionen des Fahrzeugs nicht beeintr chtigt Die Wahl der geeigneten Einbaustelle h ngt sowohl von sthetischen Faktoren als auch vom Innenraum Ihres Fahrzeugs ab Normalerweise werden die Tieft ner im Kofferraum im R cksitz oder im hinteren Teil des Fahrzeugs installiert 2008 directed electronics Alle Rechte vorbehalten 45 HOHEPUNKTE
67. page 4 Un haut parleur de graves deux bobines mobiles de 2 ohms raccord es en s rie constitue une charge de 4 ohms pour l amplificateur 1 Configurez le haut parleur de graves en s rie en raccordant l une des bornes n gatives la borne positive de l autre bobine 2 Raccordez la borne positive de la premi re bobine la borne positive de l amplificateur Raccordez la borne n gative de la seconde bobine la borne n gative de l amplificateur Parall le Un haut parleur deux bobines mobiles de 2 ohms Voir la figure 3 la page 4 Un haut parleur de graves deux bobines mobiles de 2 ohms raccord es en parall le constitue une charge de 1 ohm pour l amplificateur 1 Configurez le haut parleur de graves en parall le en raccordant entre elles les deux bornes positives et les deux bornes n gatives 2 Raccordez les bornes positives du haut parleur de graves la borne positive de l amplificateur Raccordez les bornes n gatives du haut parleur de graves la borne n gative de l amplificateur Parall le Un haut parleur deux bobines mobiles de 4 ohms Voir la figure 4 la page 5 Un haut parleur de graves deux bobines mobiles de 4 ohms raccord es en parall le constitue une charge de 2 ohms pour l amplificateur 1 Configurez le haut parleur de graves en parall le en raccordant entre elles les deux bornes positives et les deux bornes n gatives
68. para refor ar a reprodu o sonora do alto falante Uma caixa sintonizada corretamente produz ganho em toda a largura de banda do sistema de subwoofer e oferece mais controle do cone que uma caixa selada Uma sintoniza o baixa produz menos ganho geral mas maior extens o graves baixos Uma caixa com sintoniza o alta oferece mais ganho mas limita a resposta na faixa baixa do sistema Uma das vantagens de ter uma caixa ventilada que ela pode ser sintonizada para uma frequ ncia espec fica conhecida como Fb Outra especifica o importante da caixa o par metro F3 a frequ ncia cr tica na qual a resposta do driver cai 3dB Este n mero importante para configurar um filtro passa alta ou o ORION IntelliQ O IntelliQ deve ser configurado na mesma frequ ncia que o par metro F3 pois isso impedir que o alto falante se danifique ou seja sofra sobrecarga O bom planejamento e a constru o apropriada assegurar o a melhor resposta do sistema As pr ximas p ginas descrevem as muitas caixas e designs diferentes que permitem que os subwoofers XTRPRO tenham melhor desempenho 72 2008 directed electronics Todos os direitos reservados RECOMENDACOES PARA CAIXAS Detalhes da caixa 1 Dimens es externas calculadas para material de constru o de 190 mm 3 4 de espessura 2 Inclui o deslocamento do alto falante 3 Os volumes fornecidos s o volumes de sintonizac o sem acr scimo 4 As caixas po
69. pour renforcer la puissance acoustique du haut parleur Un caisson correctement accord permet un gain lev sur toute la bande passante du caisson de graves et offre un meilleur contr le qu un caisson clos Un accord bas donne moins de gain d ensemble mais une meilleure extension extr mes graves Avec un caisson accord haut le gain est plus lev mais la r ponse du syst me dans les extr mes graves est limit e L un des avantages d un caisson event accord est la possibilit d accord une fr quence particuli re appel e Fb Une autre caract ristique importante du caisson est F3 la fr quence laquelle la r ponse du haut parleur est r duite de 3 dB Il s agit d une valeur importante pour le r glage du filtre passe haut ou du dispositif ORION IntelliQ Le dispositif IntelliQ doit tre r gl la fr quence F3 car cela permet d viter d endommager le haut parleur ou de le surcharger Une bonne pr paration et une construction ad quate garantissent la meilleure r ponse du syst me Les pages suivantes d crivent plusieurs types de caissons permettant d obtenir le meilleur fonctionnement des haut parleurs de graves XTRPRO 32 2008 directed electronics Tous droits r serv s RECOMMANDATIONS SUR LES ENCEINTES D tails des enceintes 1 Dimensions externes calcul es pour des mat riaux de 3 4 2 Inclut le volume d encombrement des haut parleurs 3 Les volumes indiqu s sont le volume
70. quenza uguale a F3 per prevenire danni all altoparlante causati da un eventuale sovraccarico Una pianificazione attenta e una costruzione appropriata garantiscono la risposta migliore dell impianto Nelle pagine successive sono illustrate numerosi tipi di casse e costruzioni che permettono di ottenere risultati ottimale dai subwoofer XTRPRO 62 2008 directed electronics tutti i diritti riservati RACCOMANDAZIONI PER LA CASSA Dettagli della cassa 1 Le misure esterne sono calcolate in base a un materiale da costruzione spesso 19 mm 0 75 in 2 Comprendono il volume interno del diffusore 3 1 volumi indicati sono netti 4 La cassa comprende una quantit minima di materiale di riempimento Occorre solo il materiale strettamente sufficiente per allineare l interno della cassa Legenda relativa alla cassa sigillata vedi pagine 18 20 e 22 per le misure Proprieta della cassa Descrizione Tipo cassa sigillata Forma prisma quadrato gt Superiore e inferiore i Anteriore e posteriore Laterali 2008 directed electronics tutti i diritti riservati Parametri della cassa Vb V totale Qtc QL F3 Riempitivo HH uw ou Dimensioni esterne A B G Dimensioni interne A B G Spessore delle pareti Anteriore Laterali Parti della cassa Forma della cassa prisma quadrato 1 superiore 1 inferiore profondit c
71. ques uns de ces facteurs La taille du caisson est directement proportionnelle au rendement et la puissance admissible du haut parleur La puissance admissible est plus lev e pour un haut parleur de graves dans un petit caisson que pour le m me haut parleur de graves dans un plus grand caisson Pour le rendement c est exactement le contraire un grand caisson permet de reproduire les tr s basses fr quences avec un volume plus lev et moins de puissance qu un petit caisson Le type de caisson clos ci dessous est le meilleur pour la qualit d ensemble du son La taille du caisson d pend de la puissance et du type de v hicule dans lequel il doit tre plac Les grands caissons conviennent mieux pour les faibles puissances 25 50 de la puissance admissible du haut parleur et les grands v hicules ou bien pour obtenir un plus grand volume sonore Il faut utiliser un petit caisson dans le cas d une forte puissance 50 100 de la puissance admissible du haut parleur ou d un petit v hicule gain lev ou bien pour obtenir une plus grande pr cision de reproduction du son Un caisson clos plus petit permet un meilleur contr le ce qui se traduit par des graves plus rapides et plus pr cis Par rapport un mod le clos un caisson vent accord offre un meilleur rendement et une puissance acoustique plus lev e dans les extr mes graves Un caisson clos utilise l onde arri re son provenant de l arri re du c ne
72. rnes A B C Epaisseur parois Avant C t s El ments du caisson Forme du caisson prisme carr 1 haut 1 bas profondeur c largeur b paisseur 1 avant 1 arri re hauteur a largeur d paisseur 2 c t s hauteur a profondeur c paisseur Montage du haut parleur Montage Avant l ments de l vent 1 gaine diam tre ext rieur e diam tre int rieur g longueur h 2008 directed electronics Tous droits r serv s ESPANOL INSTALACION El rendimiento de estos subwoofers XTRPRO es directamente proporcional a la calidad de la instalaci n El cuidado que se tenga durante el proceso de instalaci n ser recompensado con muchos a os de rendimiento satisfactorio Si no est seguro de sus capacidades de instalaci n p dale asistencia t cnica al distribuidor autorizado local de Orion Los distribuidores de Orion son profesionales capacitados que se dedican a extraer el rendimiento m ximo de los sistemas Orion Si decide instalar este sistema de altavoces usted mismo lea toda la secci n sobre cajas selladas y ventiladas antes de comenzar la instalaci n UBICACIONES DE MONTAJE DE LOS ALTAVOCES Escoger la ubicaci n correcta de los altavoces tendr un efecto m ximo en la calidad del sonido del sistema Es necesario que usted tenga en cuenta varias consideraciones cuando escoja el lugar que mejor se adapte a sus necesidades
73. ssuem uma quantidade minima de material abafador necess rio ter material suficiente para revestir a parte interna da caixa Tradu o do diagrama da caixa selada ver as Propriedades da caixa Propriedades da caixa Tipo Caixa fechada Formato Prisma quadrada gt Topo e parte i inferior Laterais 2008 directed electronics Todos os direitos reservados medidas nas p ginas 18 20 e 22 Par metros da caixa Vb V total Qtc QL F3 Enchimento II HW Dimens es externas A B G Dimens es internas A B C Espessura da parede Frente Laterais Partes da caixa Formato da caixa Prisma quadrada 1 topo 1 parte inferior profundidade c largura b espessura 1 frente 1 parte posterior altura a largura d espessura 2 laterais altura a profundidade c espessura Montagem do alto falante Montagem Frente 73 Traduc o do diagrama da caixa ventilada ver as medidas nas p ginas 19 21 e 23 Propriedades da caixa Descri o Tipo Caixa ventilada Vb Formato Prisma quadrada V total Qtc QL F3 Enchimento Il gt i Topo e parte i inferior Frente e parte posterior Laterais 74 Par metros da caixa Aberturas N de aberturas Formato da abertura redondo Extremidades da abertura uma alinhada Dv Lv Dimens es e
74. sta del excitador ha bajado 3 dB Este es un n mero importante cuando se trata de ajustar el filtro de pasaaltas del ORION IntelliQ El IntelliQ debe tener la frecuencia F3 para evitar da ar o sobrecargar el altavoz La buena planificaci n y la construcci n correcta garantizan la mejor respuesta posible del sistema En las siguientes p ginas se presentan diversas cajas y dise os que permiten que los subwoofers XTRPRO se desempe en de la mejor manera posible 42 2008 directed electronics Reservados todos los derechos RECOMENDACIONES PARA LA CAJA Detalles de la caja 1 Las dimensiones externas se han calculado para un material de construcci n de 34 plg de grosor 2 Incluye el desplazamiento del altavoz 3 Los vol menes que se dan son vol menes de sintonizaci n neta 4 Las cajas contienen una cantidad m nima de material amortiguador Se necesita s lo material suficiente para recubrir la superficie interna de la caja Traducci n del diagrama de la caja sellada las medidas se encuentran en las p ginas 18 20 y 22 Propiedades de la caja Descripci n Tipo caja cerrada Forma prisma cuadrado arriba y parte de abajo 0 gt adelante y i parte de atr s Par metros de la caja Vb E V total Qtc QL F3 Fill Dimensiones externas A B C Dimensiones internas A B C Grosor de la pared Parte de adelante Lados
75. stributed by ABLE gt Directed Electronics is committed to delivering Drixected Die ese oan world class quality products and services ELECTRONICS NE ns that excite and delight our customers Vista CA 92081 WWW DIRECTED COM O 2008 Directed Electronics All rights reserved GXTRPRO102 2008 11
76. t sans pr avis D TAILS DU CAISSON 1 Les param tres indiqu s ne sont valables que pour des applications convention nelles Pour obtenir de l aide veuillez t l phoner au service d assistance tech nique audio 2 Panneau de fibres de densit moyenne de 19 mm recommand 3 Les recommandations de caissons indiquent des volumes NETS Les volumes du haut parleur et de l vent sont pris en compte dans le volume du caisson Il n est pas n cessaire d ajouter ces volumes pour obtenir le volume BRUT du caisson REMARQUES En raison des possibilit s de puissance lev e et de la longue course de ces haut parleurs de graves les param tres Thiele Small ont t calcul s et mesur s l aide d un syst me d analyse Klippel Le facteur d efficacit EBP est d termin par la formule suivante Fs Qes EBP Les valeurs d EBP inf rieures ou gales 50 indiquent qu un caisson clos est pr f rable entre 50 et 90 les haut parleurs de graves sont polyvalents pour une valeur sup rieure ou gale 90 un caisson vent accord est recommand Toujours utiliser et r gler des filtres subsoniques en fonction des mod les de cais sons vent accord 2008 directed electronics Tous droits r serv s 31 EXPLICATION DES CARACT RISTIQUES TECHNIQUES DES CAISSONS De nombreux facteurs entrent en jeu dans la d termination du meilleur type de caisson pour un utilisateur ou un v hicule donn Voici quel
77. te des Geh uses n tig Erkl rung des Diagramms f r geschlossene Geh use MaBe finden Sie auf S 18 20 und 22 Geh useeigenschaften Beschreibung Geh useparameter Typ Geschlossen Vb Form Quader V total Qtc QL F3 F llung AuBenmaBe A B C InnenmaBe A A B G Wandst rke Vorn Seiten Geh useteile Geh useform Quader 1 Oberseite 1 Unterseite Tiefe c Breite b Dicke 1 Vorderseite 1 R ckseite H he a Breite d Dicke 2 Seiten H he a Von und Tiefe c hinten Dicke lt 0 gt Treibereinbau Einbau Vorn 2008 directed electronics Alle Rechte vorbehalten 53 Erkl rung des Diagramms f r Bassreflexgeh use MaBe finden Sie auf S 19 21 und 23 Geh useeigenschaften Beschreibung Typ Bassreflexbox Vb Form Quader V total Fb QL F3 F llung gt Geh useparameter Vorn und hinten Seiten 54 ffnungen Zahl d ffnungen Form Rund 1 b ndige ffnung Dv Lv Au enma e A B C InnenmaBe A B C Wandst rke Vorn Seiten Geh useteile Geh useform Quader 1 Oberseite 1 Unterseite Tiefe c Breite b Dicke 1 Vorderseite 1 R ckseite H he a Breite d Dicke 2 Seiten H he a Tiefe c Dicke Treibereinbau Einbau V
78. te effettiva m quadrati Sd superficie radiante effettiva sq in Gamma di frequenza Hz Prodotto energiaelarghezza di banda EBP Dimensioni fisiche del driver Volume interno del diffusore cu ft Diametro fori di montaggio pollici millimetri 2008 directed electronics tutti i diritti riservati Profondit di montaggio pollici millimetri Peso magneti oz Diametro telaio pollici millimetri Casse raccomandate Cassa sigillata tipica cu ft Cassa ventilata cu ft Frequenza di sintonizzazione dell apertura Hz Area equivalente dell apertura pollici Lunghezza dell apertura pollici dati tecnici sono soggetti a modifica senza preavviso DETTAGLI DELLA CASSA 1 parametri elencati sono validi solo per applicazioni convenzionali per ulteriori informazioni rivolgersi al servizio di assistenza 2 Si suggerisce una cassa in MDF pannelli di fibre a media densit da 0 75 1 9 cm 3 valori suggeriti per il volume della cassa sono valori NETTI Il volume della cassa tiene conto dei volumi dell altoparlante e dell apertura non occorre aggiungerli per calcolare il volume LORDO della cassa NOTE A causa dell elevata potenza generabile da questi woofer e della loro lunga escursione i parametri Thiele Small sono stati calcolati mediante un analizzatore Klippel Il prodotto energiaelarghezza di banda EBP calcolato co
79. these XTRPRO subwoofers is directly proportional to the quality of the installation Care taken with the installation process will be rewarded by years of satisfying performance If you are unsure of your installation abilities please refer to your local authorized ORION dealer for assistance Orion dealers are trained professionals dedicated to extracting the maximum performance out of your Orion system If you decide to install this speaker system yourself please read the entire section on sealed and vented enclosures before starting the installation FINDING SPEAKER MOUNTING LOCATIONS Choosing the correct speaker locations will have the greatest effect on the sound quality of the system Different considerations are needed when choosing the locations that best suit your needs The locations must be large enough for the speakers to fit Care is needed to ensure that the location you have chosen will not affect any of the mechanical or electrical operations of the vehicle Determining the best location for the speakers will depend on your cosmetic needs and your vehicle s interior Usually the woofers are installed in the trunk rear seat or rear of the vehicle 2 O 2008 directed electronics all rights reserved FEATURES 1 2 3 tr 14 13 a 12 109000080 o Besesesem o 0000000000 0000000000 0000000000 2000000000 FS Figure 1 Z Figura 1 7 Abbildung 1
80. tsprecher mit dem entsprechenden positiven und negativen Terminal am zweiten Verst rker verbinden TECHNISCHE DATEN Erkl rung der Daten Details siehe Seite 14 und 15 50 Modell Teilenummer XTRPRO Gr Be Thiele Small Parameter Fs Freiluftresonanz Hz Vas Aquivalente Nachgiebigkeit KubikfuB Vas Aquivalente Nachgiebigkeit Liter Qms Q mechanisch Qes Q elektrisch Qts totaler Treiberwert f r Q Re GS Widerstand Ohm Z Nennimpedanz Ohm 2008 directed electronics Alle Rechte vorbehalten Le Induktivit t mh Wirkungsgrad 1 W bei 1 M dB Wirkungsgrad 2 86 V bei 1 M dB Xmax linearer Hub in eine Richtung Zoll Xmax linearer Hub in eine Richtung mm Pe Dauerbelastbarkeit Watt Spitzenbelastbarkeit Musik Watt Mms Bewegte Gesamtmasse Gramm Cms mechanische Nachgiebigkeit mm N BI Motorst rke Tesla M Sd effektiver Strahlbereich Quadratzentimeter Sd effektiver Strahlbereich Quadratmeter Sd effektiver Strahlbereich Quadratzoll Frequenzbereich Hz Verst rkungs Bandbreitenprodukt EBP Abmessungen des Treibers Lautsprecherhub KubikfuB Einbaulochdurchmesser Zoll mm Einbautiefe Zoll mm Magnetgewicht Unzen Korbdurchmesser Zoll mm Empfohlene Geh use Typisches geschlossenes Geh use KubikfuB Bassreflexgeh use KubikfuB
81. ttom depth c 15 36 in 390 mm i width b 18 5 in 470 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 12 in 305 mm width d 17 in 432 mm thickness 0 75 in 19 mm 2 Sides height a 12 in 305 mm depth c 15 36 in 390 mm thickness 0 75 in 19 mm Driver Mounting Mounting Front h Vent Parts 4 A 1 Duct y O Do 9 outside diameter e 4 25 in 108 mm inside diameter g 4 in 102 mm length h 11 26 in 286 mm 2008 directed electronics all rights reserved 21 XTRPRO152 amp 154 Sealed Enclosure Recommendations Box Properties Description Box Parameters Type Closed Box Vb 2 cu ft Shape Prism Square V total 2 078 cu ft Qtc 0 963 QL 5 281 F3 37 55 Hz Fill none External Dimensions A 17 5 in 445 mm B 17 5 in 445 mm C 15 52 in 394 mm Internal Dimensions A 16 in 406 mm B 16 in 406 mm 7 C 14 02 in 356 mm C Wall Thickness Front 0 75 in 19 mm lt lt _B gt Side 0 75 in 19 mm gt Box Parts Box Shape Square Prism 1 Top 1 Bottom depth c 15 52 in 394 mm width b 17 5 in 445 mm thickness 0 75 in 19 mm 1 Front 1 Back height a 16 in 406 mm lt d gt lt c gt width d 16 in 406 mm thickness 0 75 in 19 mm 2 Sides Front amp height a 16 in 406 mm a Back depth c 15 52 in 394
82. ue to improper connection to equipment of another manufacturer modifi cation of existing equipment or Product which has been opened or tampered for any reason Units which are found to be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but may be replaced at the absolute and sole discretion of Directed Unit must be returned to Directed DO NOT RETURN THE ENTIRE ENCLOSURE THE UNIT ENCLOSURE IS COVERED BY A SEPARATE 90 DAY LIMITED CONSUMER WARRANTY PLEASE ONLY RETURN THE WARRANTIED UNIT UNLESS A WARRANTY CLAIM IS BE ING MADE FOR THE ENCLOSURE postage pre paid with bill of sale or other dated proof of purchase bearing the following information consumer s name telephone number and address authorized dealer s name and address and product description Unit must be returned to the following address ATTN WARRANTY DEPART MENT Directed Electronics 1 Viper Way Vista CA 92081 Note This warranty does not cover labor costs for the removal and or reinstallation of the Unit IN ORDER FOR THE TWO YEAR WARRANTY TO BE VALID YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED DIRECTED DEALER ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION AND PURCHASE WILL BE COVERED BY THE LIMITED 1 YEAR WARRANTY BY PURCHASING THIS PRODUCT ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY IM PLIED WARRANTY WARRANTY OF MERCHANTABILITY FITNES
83. ura 12 Abbildung 12 1 Connect one of the speaker s voice coils to the first amplifier by connecting the positive terminal and the negative terminal from the speaker to the respective positive terminal and the negative terminal from the first amplifier 2 Connect the other of the speaker s voice coils to the second amplifier by connecting the positive terminal and negative terminal from the speaker to the respective positive terminal and the negative terminal from second amplifier 2008 directed electronics all rights reserved 13 SPECIFICATIONS Model Part Number XTRPRO102 XTRPRO104 XTRPRO122 Thiele Small Parameters Fs free air resonance Hz 28 0 32 1 30 5 Vas equivalent compliance cu ft 0 681 0 587 1 198 Vas equivalent compliance liters 19 300 16 630 33 950 Qms Q mechanical 5 00 5 12 6 02 Qes Q electrical 0 48 0 54 0 62 Qts total driver Q 0 44 0 49 0 56 Re DC resistance ohms 4 1 7 2 4 1 Z nominal impedance ohms 4 8 4 Le inductance mh 2 03 3 00 2 06 Efficiency 1W 1M dB 81 3 81 9 83 7 Efficiency 2 86 V 1M dB 84 7 82 7 87 2 Xmax one way linear excursion in 0 702 0 702 0 702 Xmax one way linear excursion mm 17 825 17 825 17 825 Pe continuous power handling watts 500 500 500 Peak power handling music watts 1000 1000 1000 Mms total moving mass grams 190 65 1
84. ve Anschluss an der ersten Tieft ner Schwingspule mit dem positiven Anschluss an der zweiten Tieft ner Schwingspule verbunden ist Drei Tieft ner mit doppelten 2 Ohm Schwingspulen wobei die Schwingspulen jedes Tieft ners in Reihe und dann die drei Tieft ner parallel geschaltet wurden 48 2008 directed electronics Alle Rechte vorbehalten Lastwiderstand von 1 33 Ohm am Verst rker 1 SchlieBen Sie jeden Tieft ner in Reihe an indem Sie das negative Terminal der ersten Schwingspule mit dem positiven Terminal der zweiten Spule verbinden 2 Verbinden Sie das positive Terminal der jeweils ersten Tieft ner Schwingspule mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der jeweils zweiten Tieft ner Schwingspule mit dem negativen Terminal am Verst rker Reihe Parallel Vier Lautsprecher doppelte 4 Ohm Schwingspulen Siehe Abbildung 9 auf Seite 10 Hinweis Stellen Sie sicher dass die Tieft neranschl sse wie gezeigtvorgenommen wurden wobei der negative Anschluss an der ersten Tieft ner Schwingspule mit dem positiven Anschluss an der zweiten Tieft ner Schwingspule verbunden ist Vier Tieft ner mit doppelten 4 Ohm Schwingspulen sollten so angeschlossen werden dass die Schwingspulen an jedem Tieft ner in Reihe geschaltet und dann die vier Tieft ner parallel geschaltet werden Lastwiderstand von 2 Ohm am Verst rker 1 SchlieBen Sie jeden Tieft ner in Reihe an indem
85. vecci n forzada 10 Protector de im n de PVC 11 Dos bobinas ac sticas de alta temperatura de cobre de 20 o de 40 12 Respiradero en el formador de la bobina ac stica Parte del sistema mejorado de enfriamiento de bobina ac stica convecci n forzada 13 Dos ara as Conex entrelazadas con conductores de oropel bordado y enlazado 14 Bloques de terminales a la medida 15 Anillo de guarnici n de Acrilonitrilo Butadieno Estireno ABS 36 2008 directed electronics Reservados todos los derechos CONFIGURACIONES DE CABLEADO En serie un altavoz dos bobinas ac sticas de 2 Q Vea la figura 2 en la p gina 4 Un woofer con dos bobinas ac sticas de 2 Q y las bobinas ac sticas en serie produce una carga de 4 Q en el amplificador 1 Conecte el woofer en serie conectando la terminal negativa de una de las bobinas a la terminal positiva de la otra bobina 2 Conecte la terminal positiva de la primera bobina a la terminal positiva del amplificador Conecte la terminal negativa de la segunda bobina a la terminal negativa del amplificador En paralelo un altavoz dos bobinas ac sticas de 2 Vea la figura 3 en la p gina 4 Un woofer con 2 bobinas ac sticas de 2 Q y las bobinas ac sticas en paralelo produce una carga de 1 Q en el amplificador 1 Conecte el woofer en paralelo conectando las dos terminales positivas entre s y las dos terminales negativas entre s 2 Conecte
86. verbinden 2 Verbinden Sie das positive Terminal der ersten Schwingspule am jeweiligen Tieft ner mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der zweiten Schwingspule am jeweiligen Tieft ner mit dem negativen Terminal am Verst rker Reihe Parallel Drei Lautsprecher doppelte 4 Ohm Schwingspulen Siehe Abbildung 7 auf Seite 8 Hinweis Stellen Sie sicher dass die Tieft neranschl sse wie gezeigtvorgenommen wurden wobei der negative Anschluss an der ersten Tieft ner Schwingspule mit dem positiven Anschluss an der zweiten Tieft ner Schwingspule verbunden ist Drei Tieft ner mit doppelten 4 Ohm Schwingspulen wobei die Schwingspulen jedes Tieft ners in Reihe und dann die drei Tieft ner parallel geschaltet wurden Lastwiderstand von 2 67 Ohm am Verst rker 1 SchlieBen Sie jeden Tieft ner in Reihe an indem Sie das negative Terminal der ersten Schwingspule mit dem positiven Terminal der zweiten Spule verbinden 2 Verbinden Sie das positive Terminal der jeweils ersten Tieft ner Schwingspule mit dem positiven Terminal am Verst rker Verbinden Sie das negative Terminal der jeweils zweiten Tieft ner Schwingspule mit dem negativen Terminal am Verst rker Reihe Parallel Drei Lautsprecher doppelte 2 Ohm Schwingspulen Siehe Abbildung 8 auf Seite 9 Hinweis Stellen Sie sicher dass die Tieft neranschl sse wie gezeigtvorgenommen wurden wobei der negati
87. ways to improve our product the features and specifications are subject to change without notice PRACTICE SAFE SOUNDTM Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss High powered automotive sound systems can generate sound pressure levels in excess of 130dB When playing your system at high levels please use hearing protection and prevent long term exposure Model Number Serial Number Date of Purchase 2008 directed electronics all rights reserved 1 WHAT S IN THE BOX Included in this box are all the necessary mounting hardware and cables for your basic installation Listed below is a detailed list of the components included in this system package Quantity Description 1 Owner s Manual 1 Orion XTRPRO woofer 1 Mounting template 1 Trim ring with hardware TOOLS OF THE TRADE Listed are the majority of the tools required to perform the installation Having the proper tools will make the installation much easier It is very difficult when you get half way through the installation and discover that you require a specific tool to get yourself through a particular part of the installation Some of these tools are necessities Some make the job much easier e Marking Pen e Electric Drill and assorted Bits e Phillips Screwdriver e Wire Strippers e Allen Wrenches e Volt Ohm Meter Optional e Table Saw e Jig Saw e Wire Cutters e Wire Crimpers INSTALLATION The performance of
88. woofers ao terminal positivo do amplificador Conecte os terminais negativos dos woofers ao terminal negativo 2008 directed electronics Todos os direitos reservados 67 do amplificador S rie Paralela Dois alto falantes duas bobinas de 2 ohm Ver figura 6 na p gina 7 Nota Verifique e certifique se de que os cabos dos woofers estejam conectados como mostrado com o terminal negativo da bobina do primeiro woofer conectado ao terminal positivo da bobina do segundo woofer Dois woofers com duas bobinas m veis de 2 ohm conectadas em s rie e os dois woofers em s rie conectados em paralelo resultam em uma carga de 2 ohm ao amplificador 1 Conecte cada woofer em s rie unindo o terminal negativo da primeira bobina ao terminal positivo da segunda bobina 2 Conecte o terminal positivo da primeira bobina de cada woofer ao terminal positivo do amplificador Conecte o terminal negativo da segunda bobina de cada woofer ao terminal negativo do amplificador S rie Paralela Tr s alto falantes duas bobinas de 4 ohm Ver figura 7 na p gina 8 Nota Verifique e certifique se de que os cabos dos woofers estejam conectados como mostrado com o terminal negativo da bobina do primeiro woofer conectado ao terminal positivo da bobina do segundo woofer Tr s woofers com duas bobinas m veis de 4 ohm com as bobinas de cada woofer conectadas em s rie e em seguida os tr s woofers em paralelo resultam em uma
89. xternas A B C Dimens es internas A B C Espessura da parede Frente Laterais Partes da caixa Formato da caixa Prisma quadrada 1 topo 1 parte inferior profundidade c largura b espessura 1 frente 1 parte posterior altura a largura d espessura 2 laterais altura a profundidade c espessura Montagem do alto falante Montagem Frente Partes da abertura 1 duto di metro externo e di metro interno g comprimento h 2008 directed electronics Todos os direitos reservados WARRANTY LIMITED ONE YEAR CONSUMER WARRANTY LIMITED TWO YEAR CONSUMER WARRANTY FOR AUTHORIZED DIRECTED DEALER PURCHASE amp INSTALLATION Directed Electronics herein Directed promises to the original purchaser of the subwoofer or amplifier as applicable herein Unit or Product to repair or replace with a new or refurbished Unit at Directed s sole and absolute discretion should the Unit prove to be defective in workmanship or material under normal use for a period of two years from the date of purchase from the authorized Directed dealer PROVIDED the Unit was purchased and installed by an authorized Directed dealer During this two year period there will be no charge for the repair or replacement PROVIDED the Unit is returned to Directed DO NOT RETURN THE ENTIRE ENCLOSURE PLEASE RETURN THE WARRANTIED UNIT ONLY shipping prepaid

Orion Car Audio XTRPRO124 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents